Efficient micropore sizes for carbon dioxide physisorption of pine cone-based carbonaceous materials at different temperatures

Cellulose-Amine Porous Materials: The Effect of Activation Method on Structure, Textural Properties, CO2 Capture, and Recyclability

CO2 capture via physical adsorption on activated porous carbons represents a promising solution towards effective carbon emission mitigation. Additionally, production costs can be further decreased by utilising biomass as the main precursor and applying energy-efficient activation. In this work, we developed novel cellulose-based activated carbons modified with amines (diethylenetriamine (DETA), 1,2-bis(3-aminopropylamino)ethane (BAPE), and melamine (MELA)) with different numbers of nitrogen atoms as in situ N-doping precursors. We investigated the effect of hydrothermal and thermal activation on the development of their physicochemical properties, which significantly influence the resulting CO2 adsorption capacity. This process entailed an initial hydrothermal activation of biomass precursor and amines at 240 °C, resulting in C+DETA, C+BAPE and C+MELA materials. Thermal samples (C+DETA (P), C+BAPE (P), and C+MELA (P)) were synthesised from hydrothermal materials by subsequent KOH chemical activation and pyrolysis in an inert argon atmosphere. Their chemical and structural properties were characterised using elemental analysis (CHN), infrared spectroscopy (IR), scanning electron microscopy (SEM), and thermogravimetric analysis (TG). The calculated specific surface areas (SBET) for thermal products showed higher values (998 m2 g-1 for C+DETA (P), 1076 m2 g-1 for C+BAPE (P), and 1348 m2 g-1 for C+MELA (P)) compared to the hydrothermal products (769 m2 g-1 for C+DETA, 833 m2 g-1 for C+BAPE, and 1079 m2 g-1 for C+MELA). Carbon dioxide adsorption as measured by volumetric and gravimetric methods at 0 and 25 °C, respectively, showed the opposite trend, which can be attributed to the reduced content of primary adsorption sites in the form of amine groups in thermal products. N2 and CO2 adsorption measurements were carried out on hydrothermal (C) and pyrolysed cellulose (C (P)), which showed a several-fold reduction in adsorption properties compared to amine-modified materials. The recyclability of C+MELA, which showed the highest CO2 adsorption capacity (7.34 mmol g-1), was studied using argon purging and thermal regeneration over five adsorption/desorption cycles.

A Study on Pre-Oxidation of Petroleum Pitch-Based Activated Carbons for Electric Double-Layer Capacitors

Electric double-layer capacitors (EDLCs) are an excellent electrochemical energy storage system (ESS) because of their superior power density, faster charge-discharge ability, and longer cycle life compared to those of other EES systems. Activated carbons (ACs) have been mainly used as the electrode materials for EDLCs because of their high specific surface area, superior chemical stability, and low cost. Petroleum pitch (PP) is a graphitizable carbon that is a promising precursor for ACs because of its high carbon content, which is obtained as an abundant by-product during the distillation of petroleum. However, the processibility of PP is poor because of its stable structure. In this study, pre-oxidized PP-derived AC (OPP-AC) was prepared to investigate the effects of pre-oxidation on the electrochemical behaviors of PP. The specific surface area and pore size distribution of OPP-AC were lower and narrower, respectively, compared to the textural properties of untreated PP-derived AC (PP-AC). On the other hand, the specific capacitance of OPP-AC was 25% higher than that of PP-AC. These results revealed that pre-oxidation of PP induces a highly developed micropore structure of ACs, resulting in improved electrochemical performance.

Recent Progress Using Solid-State Materials for Hydrogen Storage: A Short Review

With the rapid growth in demand for effective and renewable energy, the hydrogen era has begun. To meet commercial requirements, efficient hydrogen storage techniques are required. So far, four techniques have been suggested for hydrogen storage: compressed storage, hydrogen liquefaction, chemical absorption, and physical adsorption. Currently, high-pressure compressed tanks are used in the industry; however, certain limitations such as high costs, safety concerns, undesirable amounts of occupied space, and low storage capacities are still challenges. Physical hydrogen adsorption is one of the most promising techniques; it uses porous adsorbents, which have material benefits such as low costs, high storage densities, and fast charging–discharging kinetics. During adsorption on material surfaces, hydrogen molecules weakly adsorb at the surface of adsorbents via long-range dispersion forces. The largest challenge in the hydrogen era is the development of progressive materials for efficient hydrogen storage. In designing efficient adsorbents, understanding interfacial interactions between hydrogen molecules and porous material surfaces is important. In this review, we briefly summarize a hydrogen storage technique based on US DOE classifications and examine hydrogen storage targets for feasible commercialization. We also address recent trends in the development of hydrogen storage materials. Lastly, we propose spillover mechanisms for efficient hydrogen storage using solid-state adsorbents.