Intraocular pressure measurements during flap preparation using 2 femtosecond lasers and 1 microkeratome in human donor eyes

Femtosecond laser-assisted corneal transplantation with a low-energy, liquid-interface system

Femtosecond laser-assisted keratoplasty has been proposed as a treatment option for corneal transplantation. In this study, we investigated and compared the outcomes of Ziemer Z8 femtosecond laser (FSL)-assisted penetrating keratoplasty (PK) using a liquid interface versus flat interface. Thirty fresh porcine eyes underwent FSL-assisted PK with the Z8 using different levels of energies (30%, 90% or 150%) and different interfaces (liquid or flat). The real-time intraocular pressure (IOP) changes, incision geometry, corneal endothelial damage, as well as the accuracy of laser cutting and tissue reaction, were performed and compared. We found that the overall average IOP at all laser trephination stages was significantly higher with the flat interface, regardless of the energy used (68.9 ± 15.0 mmHg versus 46.1 ± 16.6 mmHg; P < 0.001). The overall mean laser-cut angle was 86.2º ± 6.5º and 88.2º ± 1.0º, for the liquid and flat platform respectively, indicating minimal deviation from the programmed angle of 90º. When high energy (150%) was used, the endothelial denuded area was significantly greater with the flat interface than with liquid interface (386.1 ± 53.6 mm² versus 139.0 ± 10.4 mm²P = 0.02). The FSL cutting did not cause obvious tissue reaction alongside the laser cut on histological evaluation. The results indicated a liquid interface is the preferable choice in FSL-assisted corneal transplantation.

Corneal stromal roughness after VisuMax and Intralase femtosecond laser photodisruption: An atomic force microscopy study

Purpose

To compare the induced corneal stromal bed roughness measured with atomic force microscopy (AFM) after LASIK flap creation with the IntraLase 60 kHz and the VisuMax femtosecond laser platforms.

Methods

Three freshly enucleated porcine eyes were operated with each femtosecond laser in this experimental study. Standard LASIK treatment parameters were used for the experiment. After LASIK flap creation, the corneal stromal roughness was assessed using a JPK NanoWizard II^® AFM in contact mode immersed in liquid. Olympus OMCL-RC800PSA commercial silicon nitride cantilever tips were used. Surface measurements were made in 10 regions of the central cornea of each sample measuring 20 x 20 microns, at 512 x 512 point resolution. Roughness was measured using the root-mean-square (RMS) value within the given regions.

Results

Measurements from 30 regions of the 3 eyes (10 measurements per eye) in the Intralase (FS1) group, and 30 regions of the 3 eyes (10 measurements per eye) in the VisuMax (FS2) group were analyzed. There was a statistically significant difference in mean ± standard deviation RMS values between the FS1 and the FS2 groups (360 ± 120 versus 230 ± 100 nm respectively; P< 0.00001).

Conclusion

This AFM study indicates that the surface of the stromal bed after LASIK flap creation is smoother in the FS2 group than the FS1 group.

Transient effect of suction on the retinal neurovasculature in myopic patients after small-incision lenticule extraction

PURPOSE

To characterize retinal neurovasculature changes after small-incision lenticule extraction (SMILE) in myopic patients.

SETTING

Ophthalmic Center, the Second Affiliated Hospital of Guangzhou Medical University, China.

DESIGN

Prospective interventional study.

METHODS

The corrected distance visual acuity/uncorrected distance visual acuity, corrected intraocular pressure (CIOP), and corneal tomography were evaluated at baseline (PRE), postoperative day (POD) 1, and POD 7. Ganglion cell-inner plexiform layer (GCIPL) and peripapillary retinal nerve fiber layer (pRNFL) thicknesses were measured. The vessel area densities (VADs, %), vessel skeleton densities (VSDs, %), vessel diameter index (VDI), and fractal dimensions (Dbox) of the superficial vascular plexus (SVP) and deep vascular plexus (DVP) were measured in a circular area (ϕ 2.5 mm) centered on the fovea.

RESULTS

A total of 38 myopic patients were recruited. The GCIPL thickness was increased after SMILE at POD 1 and POD 7 (P < .01) but no significant changes in the pRNFL thickness. The VAD, VSD, and Dbox of the SVP were decreased at POD 1 (P < .01), but not at POD 7. The VDI in small vessels of the SVP and DVP was decreased at POD 1 (P < .05) and increased at POD 7 (P < .05). Changes in CIOP were positively correlated with changes in the GCIPL thickness. Changes in CIOP were negatively correlated with changes in the VAD of small vessels and the Dbox of total vessels in the DVP. Changes in CIOP were negatively correlated with the VSD and VDI of small vessels in the DVP and changes in the VDI of big vessels in the SVP.

CONCLUSIONS

The transient fluctuations in the retinal neurovasculature after SMILE may represent a characteristic homeostasis pattern in patients after refractive surgery.

SMILE – Small Incision Lenticule Extraction

Die SMILE (small incision lenticule extraction) zählt zu den Verfahren der refraktiven Lentikel-Extraktion und hat sich im letzten Jahrzehnt zu einem etablierten Bestandteil des modernen refraktivchirurgischen Spektrums entwickelt. Dieser Beitrag gibt einen Überblick über Patientenselektion, Operationsmethode, mögliche Komplikationen und klinische Ergebnisse dieser Methode.

[SMILE - Small Incision Lenticule Extraction]

Refractive lenticule extraction is a corneal surgical technique that uses a femtosecond laser exclusively to create an intrastromal refractive lenticule for the correction of myopia and myopic astigmatism. In small incision lenticule extraction (SMILE) the generated refractive lenticule is subsequently extracted through a small incision. The reported efficacy, predictability and safety of the flap-less SMILE procedure is similar to those of femtosecond laser in situ keratomileusis (LASIK). Advantages of SMILE over LASIK include less iatrogenic dry eye, fewer induced higher-order aberrations, and potentially less biomechanical weakening of the cornea. However, there is a steeper surgeon learning curve for SMILE as the procedure is technically more challenging than LASIK. Furthermore, the current SMILE laser platform cannot use cyclotorsion control or eye-tracking technology and retreatment options are more complex compared to LASIK. This review looks at patient selection, surgical method, possible complications, retreatment options, and postoperative outcome of the SMILE technique.

Suction stability management in small incision lenticule extraction: incidence and outcomes of suction loss in 4000 consecutive procedures

PURPOSE

To report the incidence and outcomes of suction loss during small incision lenticule extraction (SMILE).

METHODS

The incidence of suction loss was measured over 4000 consecutive SMILE procedures and categorized by cause, the interface in which suction was lost and management (restart/continue SMILE, re-SMILE thinner cap, convert to laser in-situ keratomileusis [LASIK]). One-year outcomes were compared to the fellow eye where no suction loss occurred.

RESULTS

There were 20 cases of suction loss (0.50%): during the lenticule interface in seven eyes, lenticule side cut in one eye, cap interface in nine eyes and small incision for three eyes. Small incision lenticule extraction (SMILE) was continued in seven eyes, thinner cap SMILE in four eyes, LASIK in eight eyes, and the small incision was manually completed in one eye. Suction loss was caused by a Bell's reflex in 10 eyes, fixation light tracking in six eyes, patient anxiety in two eyes, a nociceptive reflex in one eye and false suction in one eye. There was no difference in results for suction loss and fellow eyes, respectively: uncorrected distance visual acuity was 20/20 or better in 100% in both groups, spherical equivalent was within ±0.50 D in 85% and 79%, one line loss of corrected distance visual acuity in 5% and 0%, and no eyes lost two lines.

CONCLUSION

Suction loss can be managed depending on the interface during which suction is lost. Treatment was completed on the same day in all instances. Visual and refractive outcomes were unaffected compared to the fellow eye in this series.

Retinal nerve fiber layer thickness after laser-assisted subepithelial keratomileusis and femtosecond LASIK: a prospective observational cohort study

Purpose

Based on the assumption that high levels of intraocular pressure (IOP) during femtosecond laser-assisted in situ keratomileusis (FS-LASIK) may compromise the retinal nerve fiber layer (RNFL), newer femtosecond platforms that operate without causing significant IOP elevation have been developed in recent years. However, this assumption has not been adequately tested. The aim of the current study was to evaluate possible changes in RFNL thickness in nonglaucomatous myopic patients undergoing FS-LASIK using the 60 KHz IntraLase^® device that significantly elevates the IOP for an appreciable period of time vs an advanced surface ablation technique (laser-assisted subepithelial keratomileusis, LASEK) that does not induce any IOP elevation.

Methods

This was a prospective, observational, controlled cohort study. One randomly selected eye of 114 consecutive eligible patients was analyzed. Inclusion criteria were myopia up to -6.00 diopters and astigmatism up to -2.00 diopters. As clinically indicated, 50 patients underwent LASEK and 64 underwent FS-LASIK. The RNFL thickness was determined with a spectral-domain optical coherence tomography device preoperatively and 3 months postoperatively by the same masked observer.

Results

There was no significant difference in preoperative refractive error, age, or sex between the groups. Preoperatively, central corneal thickness was significantly lower in the LASEK group (529.1±36.1 vs 562.4±31.6 µm, P=0.001). For the LASEK group, there was no significant difference between preoperative and postoperative RNFL thickness in the studied sectors (superior-temporal, temporal, inferior-temporal, average). For the FS-LASIK group, compared to preoperative RNFL measures, statistically significant thicker postoperative values were found for the average RNFL (mean difference: 0.67 µm, 0.7% increase, P=0.008) and the inferior-temporal sector (mean difference: 0.92 µm, 0.6% increase, P=0.02).

Conclusion

LASIK with a femtosecond platform that induces high intraoperative IOP did not cause RNFL thinning. The observed differences between preoperative and postoperative values are below the axial resolution limit of optical coherence tomography devices.

Real-Time Intraocular Pressure Measurements in the Vitreous Chamber of Rabbit Eyes During Small Incision Lenticule Extraction (SMILE)

PURPOSE

To investigate real-time intraocular pressure (IOP) during small incision lenticule extraction (SMILE) in rabbit eyes for myopia correction.

METHODS

During SMILE, real-time IOP was measured in the vitreous cavity of rabbit eyes with an optic fiber pressure sensor (OFPS). Two groups (n = 6 for each) underwent surgery, one group for a -2.00 diopter (D) refractive spherical correction and the other for a -6.00 D correction.

RESULTS

During surgery, the IOP increased once the glass contact attached to the cornea (Pre-suction), and peaked 83.94 mmHg (SD ± 23.87 mmHg) for the -2.00 D group and 89.17 mmHg (SD ± 22.66 mmHg) for the -6.00 D group, both average values were less than 110 mmHg when suction was initiated to fix the glass contact onto the cornea (Suction on). It then fell to 74.81 mmHg (SD ± 20.64 mmHg) and 76.94 mmHg (SD ± 27.43 mmHg), respectively, and remained stable during lenticule creation (Cutting). After suction stopped (Suction off), IOP fell steeply. During lenticule separation/extraction, the change in IOP was 32.26 mmHg (SD ± 2.91 mmHg). Notably, the average duration of elevated IOP during the surgery was 166.05 s (no longer than 3 min).

CONCLUSIONS

The IOP fluctuations in the vitreous cavity using an OFPS in a rabbit model during SMILE showed that real-time IOP significantly was increased during Pre-suction, Suction on, Cutting, Suction off, and lenticule separation/extraction compared to baseline IOP, although, peaked at Suction on. Neither the degree of myopic correction nor central corneal thickness significantly affected these changes in IOP.

Urrets-Zavalia Syndrome After Combined Trabeculotomy-Trabeculectomy Surgery

We report a case of a rare complication after trabeculotomy combined with a small trabeculectomy with mitomycin C in a young patient with juvenile glaucoma. The patient underwent uneventful surgery. However, postoperatively, he experienced a long-lasting hypotony with the need of 2 revision surgeries and 2 short episodes of high-intraocular pressure. He developed a fixed dilated pupil over time.

Contralateral assessment of sub-Bowman keratomileusis (SBK) microkeratome suction duration on laser-assisted in-situ keratomileusis (LASIK) flap characteristics

PURPOSE

To describe the effect of prolonging the standard suction duration during laser-assisted in-situ keratomileusis (LASIK) and its effect on flap thickness and hinge length using sub-Bowman keratomileusis (SBK) microkeratome.

METHODS

Fifty-six eyes (28 patients) were included and divided into 2 groups; Group-A: eyes with flatter corneas (36 eyes, 18 patients) and mean keratometric readings ranging from 40.13 to 43.71 diopters (D). Group-B: eyes with steeper corneas (20 eyes, 10 patients) with mean keratometric readings ranging from 43.85 to 46.72 D. One-Use-Plus SBK microkeratome was used for flap creation. For right eyes, flap was created immediately once suction was built up. In left eyes, the surgeon waited for 10 s after suction was built up before flap creation. Flap hinge length and flap thickness were measured using surgical caliper and ultrasonic pachymetry, respectively.

RESULTS

Statistically significant differences were observed in corneal flap hinge size between right eyes versus left eyes, with a mean of 3.98 ± 0.48 vs. 3.78 ± 0.55 mm (p < 0.001). Mean flap thickness in both eyes did not prove to be statistically significantly different with either surgical technique (90.2 ± 1.68 vs. 90.07 ± 1.44 μm, p = 0.8). Sub-group analysis of Group-A vs. Group-B revealed hinge sizes that were significantly larger in steeper corneas (p < 0.01 and p < 0.05, respectively). However, flap thickness in both groups was unaffected by surgical procedure (p = 0.5).

CONCLUSIONS

Increasing suction duration increases flap hinge length and stabilizes the flap, especially in steeper corneas.

Comparison of intra-ocular pressure changes with liquid or flat applanation interfaces in a femtosecond laser platform

Cataract surgery is the most common surgical procedure and femtosecond laser assisted cataract surgery (FLACS) has gained increased popularity. FLACS requires the application of a suction device to stabilize the laser head and focus the laser beam accurately. This may cause a significant escalation in intra-ocular pressure (IOP), which poses potential risks for patients undergoing cataract surgery. In this study we aimed to assess the effect of the Ziemer LDV Z8 femtosecond cataract machine on IOP. We demonstrated through a porcine model that IOP was significantly higher with a flat interface but could be abrogated by reducing surgical compression and vacuum. Pressure was lower with a liquid interface, and further altering angulation of the laser arm could reduce the IOP to 36 mmHg. A pilot series in patients showed comparable pressure rises with the porcine model (30 mmHg). These strategies may improve the safety profile in patients vulnerable to high pressure when employing FLACS with the Ziemer LDV Z8.

Excimer versus Femtosecond Laser Assisted Penetrating Keratoplasty in Keratoconus and Fuchs Dystrophy: Intraoperative Pitfalls

Purpose. To assess the intraoperative results comparing two non-mechanical laser assisted penetrating keratoplasty approaches in keratoconus and Fuchs dystrophy. Patients and Methods. 68 patients (age 18 to 87 years) with keratoconus or Fuchs dystrophy were randomly distributed to 4 groups. 35 eyes with keratoconus and 33 eyes with Fuchs dystrophy were treated with either excimer laser ([Exc] groups I and II) or femtosecond laser-assisted ([FLAK] groups III and IV) penetrating keratoplasty. Main intraoperative outcome measures included intraoperative decentration, need for additional interrupted sutures, alignment of orientation markers, and intraocular positive pressure (vis a tergo). Results. Intraoperative recipient decentration occurred in 4 eyes of groups III/IV but in none of groups I/II. Additional interrupted sutures were not necessary in groups I/II but in 5 eyes of groups III/IV. Orientation markers were all aligned in groups I/II but were partly misaligned in 8 eyes of groups III/IV. Intraocular positive pressure grade was recognized in 12 eyes of groups I/II and in 19 eyes of groups III/IV. In particular, in group III, severe vis a tergo occurred in 8 eyes. Conclusions. Intraoperative decentration, misalignment of the donor in the recipient bed, and need for additional interrupted sutures as well as high percentage of severe intraocular positive pressure were predominantly present in the femtosecond laser in keratoconus eyes.

Bilateral Iris Atrophy after the Femtosecond Assisted Laser In Situ Keratomileusis Surgery

Purpose. To report an unknown complication of laser in situ keratomileusis (LASIK) surgery. Case Presentation. A 28-year-old female presented with photophobia and glare to our eye service. She stated in her medical history that she had undergone femtosecond assisted LASIK surgery in both eyes 15 months ago and her symptoms started just after this surgery. On admission, her best-corrected visual acuity was 10/10 in both eyes. She had mydriatic pupils with no direct light reflex. Examination of the anterior segment revealed bilateral iris atrophy projecting within the LASIK ablation zone and a transillumination defect was remarkable on the slit lamp examination. Conclusion. We hypothesized that this condition may have been caused by the abnormally increased IOP that resulted in ischemia in the iris vascular plexus during the suction process of surgery.

Small incision lenticule extraction (SMILE) history, fundamentals of a new refractive surgery technique and clinical outcomes

This review summarizes the current status of the small incision lenticule extraction (SMILE) procedure. Following the early work by Sekundo et al. and Shah et al., SMILE has become increasingly popular. The accuracy of the creation of the lenticule with the VisuMax femtosecond laser (Carl Zeiss Meditec) has been verified using very high-frequency (VHF) digital ultrasound and optical coherence tomography (OCT). Visual and refractive outcomes have been shown to be similar to those achieved with laser in situ keratomileusis (LASIK), notably in a large population reported by Hjortdal, Vestergaard et al. Safety in terms of the change in corrected distance visual acuity (CDVA) has also been shown to be similar to LASIK. It was expected that there would be less postoperative dry eye after SMILE compared to LASIK because the anterior stroma is disturbed only by the small incision, meaning that the anterior corneal nerves should be less affected. A number of studies have demonstrated a lower reduction and faster recovery of corneal sensation after SMILE than LASIK. Some studies have also used confocal microscopy to demonstrate a lower decrease in subbasal nerve fiber density after SMILE than LASIK. The potential biomechanical advantages of SMILE have been modeled by Reinstein et al. based on the non-linearity of tensile strength through the stroma. Studies have reported a similar change in Ocular Response Analyzer (Reichert) parameters after SMILE and LASIK, however, these have previously been shown to be unreliable as a representation of corneal biomechanics. Retreatment options after SMILE are discussed. Tissue addition applications of the SMILE procedure are also discussed including the potential for cryo-preservation of the lenticule for later reimplantation (Mohamed-Noriega, Angunawela, Lim et al.), and a new procedure referred to as endokeratophakia in which a myopic SMILE lenticule is implanted into a hyperopic patient (Pradhan et al.). Finally, studies reporting microdistortions in Bowman's layer and corneal wound healing responses are also described.

Changes in corneal deformation parameters after lenticule creation and extraction during small incision lenticule extraction (SMILE) procedure

Purpose

To investigate the effects of lenticule creation and subsequent corneal lenticule extraction on corneal deformation parameters during small incision lenticule extraction (SMILE) procedure.

Materials and Methods

In this prospective study, 18 eyes of 10 patients (27.90±7.11 years, −5.64±2.45 diopters) scheduled for SMILE procedure were enrolled. Changes in the corneal deformation parameters, including deformation amplitude (DA), applanation time(AT1 and AT2), applanation length(AL1 and AL2), corneal velocity(CV1 and CV2), peak distance(P.Dist.), radius and intraocular pressure values were measured preoperatively, immediately after lenticule creation and subsequent to corneal lenticule extraction in all eyes with the Corvis Scheimpflug Technology (Corvis ST, OCULUS, Wetzlar, Germany). Repeated measures analysis of variance (ANOVA) with bonferroni-adjusted post hoc comparisons was performed to investigate changes following each step of the procedure.

Results

All surgical procedures were uneventful. A significant difference was detected among the three time points (pre-operation, post-lenticule creation and post lenticule extraction) for AT1 (P<0.001), AT2 (P = 0.001), DA(P<0.001), and IOP(P = 0.002). Bonferroni-adjusted post hoc comparisons indicated that there was no significant change in AT1, AT2, DA, or IOP after lenticule creation (post hoc P>0.05), but there was a significant change in these parameters following subsequent corneal lenticule extraction (post hoc P<0.01), when compared to values obtained pre-operatively. The scheimpflug camera of the Corvis ST demonstrated the intralamellar small gas bubbles formed from the vaporisation of tissue after lenticule creation and a gray zone was observed between the cap and the residual stromal bed after lenticule extraction.

Conclusions

There is a significant change in corneal deformation parameters following SMILE procedure. The changes may be caused predominantly by stromal lenticule extraction, while lenticule creation with femtosecond laser may not have an obvious effect on corneal deformation properties.

Patient and surgeon experience during laser in situ keratomileusis using 2 femtosecond laser systems

PURPOSE

To describe the subjective experience of patients and surgeons during laser in situ keratomileusis (LASIK) using the Intralase 60 kHz or the Visumax 500 kHz femtosecond laser.

SETTING

Singapore National Eye Centre, Singapore.

DESIGN

Prospective randomized clinical study.

METHODS

In myopic patients, LASIK was performed with the corneal flap created using the 60 kHz laser in 1 eye and the 500 kHz laser in the contralateral eye. Postoperatively, patients completed a standardized validated questionnaire about their subjective intraoperative experiences (eg, light perception, pain, fear). Surgeons reported their intraoperative experiences and preferences.

RESULTS

Loss of light perception occurred in 50.0% of 60 kHz laser cases and 0% of 500 kHz laser cases during docking and in 63.0% and 0% of cases, respectively, during laser flap creation (P < .0001). The mean pain score with the 60 kHz laser was significantly higher during docking (P < .0001) but not during laser flap cutting (P = .006). Subconjunctival hemorrhage occurred in 67.4% of eyes with the 60 kHz laser and in 2.2% of eyes with the 500 kHz laser (P < .0001). The 500 kHz laser was preferred by 78.3% of patients, while 21.7% preferred the 60 kHz laser (P < .0001). The surgeons preferred the 60 kHz laser in 50.0% of cases and the 500 kHz laser in 8.7% (P < .0001); 41.3% had no preference.

CONCLUSIONS

Patients preferred surgery with the 500 kHz laser with no loss of light perception, less pain, less fear, and less subconjunctival hemorrhage. Surgeons preferred the 60 kHz laser.

Changes in retinal nerve fiber layer thickness following mechanical microkeratome-assisted versus femtosecond laser-assisted LASIK

Purpose

To study the influence of the transient elevation of intraocular pressure during suction in laser-assisted in situ keratomileusis (LASIK) on the retinal nerve fiber layer (RNFL) thickness both in microkeratome assisted and femotsecond (FS) LASIK.

Patients and methods

An interventional case series that included 40 eyes suffering from myopia who were candidates for LASIK. All underwent Wave Front Guided LASIK by the same surgeon using the VisX CustomVue platform. A corneal flap was created in 20 eyes using a mechanical microkeratome Moria M2 (MMK), while the IFS IntraLase™ was used in the remaining 20 eyes. Mean suction time was recorded from “Suction ON” to “Suction OFF” time. Optic cube and RNFL thickness analysis using Spectral Domain Optical Coherence Tomography (SD-OCT) Cirrus-HD was completed before, and 1 month after LASIK.

Results

The study included 40 eyes of 20 patients. All were females with mean age 33.5 ± 6.4 years. Mean preoperative spherical equivalent was −3.62 ± 2.31D. Average preoperative RNFL thickness was 94.6 ± 12.1μm in MMK group while the postoperative average thickness was 95.1 ± 11.9 um with no statistically significant difference (P-value: 0.37). Average preoperative RNFL thickness was 108.28 ± 8.4 μm in FS group compared to 108.38 ± 11.2 μm in the postoperative average with no statistically significant difference (P-value: 0.94). Mean “Suction ON” to “Suction OFF” time was 22 seconds in the MMK group compared to 41 seconds in the FS group.

Conclusion

The rise of intraocular pressure during application of suction ring in LASIK surgery does not affect the RNFL thickness as measured by SD-OCT, whether the flap is created by MMK or FS.