Longitudinal evaluation of simulated toothbrushing on the roughness and optical stability of microfilled, microhybrid and nanofilled resin-based composites

Flexural strength and degree of conversion of universal single shade resin-based composites

Background/purpose

Recently, a group of universal single-shade resin-based composites (RBCs) has been developed to simplify the process of shade selection. Excellent mechanical and physical properties are crucial for the ultimate success and clinical longevity of restorations. Therefore, evaluating the properties of the single-shaded RBCs is imperative. This study aimed to determine the flexural strength (FS) and degree of conversion (DC) of universal single-shade RBCs.

Materials and methods

In this study, four commercial RBCs were used; three universal single-shade RBCs; Omnichroma (OC), Charisma® Diamond ONE (CD), and Vittra APS Unique (VU), and a conventional nanohybrid composite Filtek™ Z250 XT (FT) which was used as a control. Sixty composite beams and 40 composite discs were used for FS and DC, respectively. A universal test machine with a three-point bending test was used to measure the FS, whereas the DC was measured using a Fourier-transform infrared spectrometer (FTIR). Three fractured specimens from each resin composite group were qualitatively analyzed using scanning electron microscopy.

Results

ANOVA was used to compare the mean values of FS and DC among the four RBCs (OC, CD, VU, and FT). Highly significant differences were observed in the mean FS and DC values (F = 673.043, p < 0.001 and F (=782.4, p < 0.0001), respectively. The highest FS was observed in the CD group, followed by FT and VU groups; the lowest value was observed in the OC group. In addition, a statistically significant difference was identified in DC values. The highest DC value was observed in VU, followed by OC and CD, and the lowest DC value was observed in FT.

Conclusion

Universal single-shade RBCs demonstrated a good FS, except for OC, which exhibited a significantly low FS. The DC of the universal single-shade RBCs was higher than that of the conventional nanohybrid composite restorative material.

Analysis of color stability and degree of conversion of different types of resin composites

Resin composites containing surface pre-reacted glass (S-PRG) have been introduced to reduce demineralization and improve remineralization of the tooth structure. However, water diffusion within the material is necessary for its action, which can impair its overall physicomechanical properties over time, including color stability. This study aimed to evaluate the color stability and related degree of conversion (DC) of four resin composites. Discs (6 x 4 mm, n = 5/group) of microhybrid (MH), nanofilled (NF), nanohybrid (NH), and S-PRG-based nanohybrid (S-PRG-NH) composites with two opacities (A2/A2E and A2O/A2D) were prepared. Color (CIELab and CIEDE2000) was evaluated with a spectrophotometer after aging in grape juice (2 x 10 min/10mL/7days). The DC was analyzed by using Fourier transform infrared spectroscopy before and after light-curing. Data were statistically analyzed by using two-way analysis of variance and post-hoc least significant difference tests (p<0.05). In the color stability analysis, the interaction between filler type and opacity was significant (CIELab, p = 0.0015; CIEDE2000, p = 0.0026). NH presented the highest color stability, which did not differ from that of MH. The greatest color alteration was observed for S-PRG-NH. S-PRG fillers also influenced DC (p < 0.05). The nanohybrid resin composite presented favorable overall performance, which is likely related to its more stable organic content. Notwithstanding the benefits of using S-PRG-based nanohybrid resins, mostly in aesthetic procedures, professionals should consider the susceptibility of such resins to color alteration, probably due to the water-based bioactive mechanism of action.

Change in surface properties of two different dental resin composites after using various beverages and brushing

BACKGROUND

The study aimed to evaluate the influence of various beverages; with and without brushing; on the surface mechanical properties of two resin composites.

METHODS

A total of 160 disc-shaped specimens were prepared for each of the following dental composites; nanohybrid ormocer (Admira fusion, VOCO GmbH, Cuxhaven, Germany) and nanohybrid resin composite (Grandio, VOCO GmbH, Cuxhaven, Germany). The baseline surface hardness and roughness measurements were carried out after 24 h. The composite samples were randomly distributed into one of the two groups; brushing and non-brushing, which were further divided into one of the four subgroups (n = 10); artificial saliva as control, coffee, red wine, and soft drink. In the non-brushing group, the specimens were immersed in the different beverages for five minutes three times daily for 30 days. The same procedure was done for the brushing group, in addition to brushing the specimens for five seconds. The surface hardness and roughness measurements were repeated after 30 days. One-way ANOVA and independent t-tests were used for statistical analysis.

RESULTS

The soft drink had the most deteriorating effect and artificial saliva had the least. The change in surface properties was higher in the brushing subgroups. Grandio exhibited a higher change in surface microhardness while Admira fusion exhibited a higher change in surface roughness.

CONCLUSIONS

The surface properties of both dental resin composites were negatively affected by using beverages and brushing.

Isolated effect of filler particle size on surface properties of experimental resin composites before and after toothbrush abrasion

OBJECTIVE

This study aimed to isolate the relationship between filler size and the surface properties of roughness and gloss before and after toothbrush abrasion for experimental resin-based composites (RBCs) containing uniform spherical fillers.

MATERIALS AND METHODS

Five experimental light-cured RBCs with different spherical filler sizes and three commercial RBCs were studied. Forty specimens were polished using silicon carbide papers. Gloss was measured after 0, 90, 180, and 360 min of simulated toothbrushing, and surface roughness was measured before and after 360 min of toothbrushing. Two-way ANOVA/Tukey's multiple comparison tests were used to compare the RBCs, and the correlation between particle size and surface roughness or gloss was also determined.

RESULTS

After polishing and toothbrushing, RBCs with smaller fillers exhibited significantly higher gloss and lower surface roughness, and RBCs with larger fillers exhibited lower gloss and higher surface roughness. A significant correlation was found between filler particle size and gloss and surface roughness both before and after toothbrush abrasion.

CONCLUSIONS

Gloss of RBCs containing fillers with larger particle sizes was significantly reduced. After toothbrushing abrasion, the surface roughness increased for all RBCs, except those containing the finest-sized fillers. The particle size of the filler is a critical determinant of the surface roughness and gloss of RBCs, after polishing and after toothbrushing.

CLINICAL SIGNIFICANCE

Increased surface roughness caused by toothbrush abrasion reduces the gloss of resin-based composites. Resin-based composites containing finer fillers best maintain glossiness after routine tooth brushing.

Effect of oral exposure on chemical, physical, mechanical, and morphologic properties of clear orthodontic aligners

INTRODUCTION

The dental industry is heavily committed to developing more esthetic solutions for orthodontic treatments. Invisalign is a system of transparent orthodontic aligners introduced as an alternative to conventional orthodontic fittings with brackets and metal wires. This study aimed to assess the chemical, physical, mechanical and morphologic changes in these polymeric aligners after exposure to the oral environment.

METHODS

Twenty-four Invisalign orthodontic aligners were equally divided into 2 groups: an in vivo aged group in which patients used aligners for 14 days and the reference group, unexposed to the oral environment. Different experimental techniques were used to study the chemical structure, the color changes and translucency, the density and subsequent volume of the aligners, mechanical properties, surface roughness, morphology and elemental composition. The data were subjected to several statistical analyses.

RESULTS

Clear orthodontic aligners exhibit chemical stability but undergo a statistically significant optical change in color and translucency. There was a gradual increase in the water absorption rate and the dimensional variation of the polymer, indicating a strong correlation among these factors. The mechanical properties of the polymer showed a statistically significant decrease in its elastic modulus and hardness. There was a slight tendency toward increased surface roughness of the material, but no statistical differences were found between reference and aged groups. The surface morphology of the used aligners demonstrates microcracks, distortions and biofilm formation.

CONCLUSION

Intraoral aging adversely affected the physical, mechanical, and morphologic properties of the Invisalign appliance.

Effect of charcoal-based dentifrices on surface roughness of an aged resin composite

BACKGROUND

Recently, the use of whitening dentifrice has increased among patients. However, these products might increase the surface roughness of composite restorations and make them more susceptible to discoloration and plaque accumulation. This study aimed to compare the effects of two charcoal-based dentifrices and other whitening dentifrices with different mechanisms of action on the surface roughness of an aged resin composite.

METHODS

Forty-five composite specimens were made (2 × 7mm) and their initial surface roughness was obtained using a Profilometer. The specimens were subjected to the Accelerated Artificial Aging (AAA) process for 300 hours. Then, the surface roughness of the specimens was reevaluated using the Profilometer. The specimens were randomly divided into 5 groups (N.=9), namely Control (Gc), Bencer (Gb; Sormeh Company, Tehran, Iran), Perfect White Black (Gp), Colgate Total Whitening (Gt), and Colgate Optic White (Go) (Colgate-Palmolive Company, New York, NY, USA). The specimens were brushed for 14 minutes with respective dentifrices. In the Gc group, the specimens were only brushed with distilled water. The surface roughness of the specimens was measured again. The data were analyzed using repeated measure ANOVA at a significance level of 0.05.

RESULTS

There was no significant difference in surface roughness parameters (Ra, Rq, Rz) between the groups, but in each group, the roughness parameters decreased after the aging procedure and increased after brushing significantly except for Rz parameter in Gb group which increased after aging and decreased after brushing.

CONCLUSIONS

None of the whitening dentifrices used in the present study had an adverse effect on the surface roughness of an aged composite resin.

Comparative study on the impact-sliding wear behaviour of CAD/CAM resin-ceramic materials and tooth enamel

OBJECTIVES

To compare the impact-sliding wear of different CAD/CAM resin-ceramic materials and tooth enamel, and explore the corresponding wear damage mechanism.

METHODS

Human tooth enamel (EN), Vita ENAMIC (Vita, VE), Lava Ultimate (3 M, LU), and GC CERASMART (GC, CS) were used in this study. The hardness, elastic modulus, and roughness values of the samples were measured. Further, impact-sliding wear tests were performed in a ball-on-flat configuration with spherical zirconia antagonists and the coefficients of friction (CoF) were recorded simultaneously. Additionally, a white light interferometer was used to determine the volume losses and scanning electron microscopy was used to observe the wear morphology of the wear scars and the damage feature in the vertical sections to clarify the damage mechanism during the impact-sliding wear test.

RESULTS

EN exhibited the highest elastic modulus and CoF, followed by VE, LU, and CS. The hardness and roughness of EN and VE were similar and were higher than those of LU and CS. Throughout the wear tests, VE exhibited the highest volume loss, whereas CS exhibited the lowest. The wear damage characteristics of VE were similar to those of EN, displaying brittle fractures of inorganic substances and plastic deformation of organic substances in the impact part, exhibiting plough marks in the sliding parts. In the case of LU and CS, the entire wear areas displayed plastic deformation of the resin matrix, exfoliation of the filler particles, and plough marks.

SIGNIFICANCE

Enamel and polymer-infiltrated ceramic network materials exhibit similar wear damage modes. Additionally, the high-density nanocomposite resin material is the most resistant to impact-sliding wear from a tribological perspective.

The Effects of Different Pediatric Drugs and Brushing on the Color Stability of Esthetic Restorative Materials Used in Pediatric Dentistry: An In Vitro Study

The aim of the current study is to observe how different pediatric drugs and tooth brushing affect the color stability of different esthetic restorative materials. Three restorative materials (composite, compomer, and glass ionomer cement (GIC)) were each used to produce 72 specimens (10 mm × 2 mm). The specimens were divided into six groups and immersed in distilled water and five different pediatric drugs (amoxicillin, ibuprofen, ventolin, paracetamol, and multivitamins). Each group was divided into two subgroups (brushed and non-brushed). Over the course of two weeks, the specimens were agitated for one minute every eight hours. Color changes in all the specimens were evaluated using a spectrophotometer at 1 and 2 weeks. GIC showed a change in color that was significantly greater than that in all the other materials in each solution, except for those in amoxicillin. After a period of 1 to 2 weeks, the most noticeable change in color was detected in the amoxicillin composite and amoxicillin GIC unbrushed groups, and after 2 weeks, a significant difference was found in the ventolin GIC unbrushed group. The color stability of the restorative materials used in pediatric dentistry can be influenced by using popular liquid pediatric medications. GIC was the least color-stable material when subjected to liquid medications.

Development and maintenance of surface gloss of dental composites after polishing and brushing: Review of the literature

OBJECTIVE

To describe the effect of the composites' composition to produce high surface smoothness/gloss using finishers/polishers, and to assess maintained smoothness/gloss under toothbrush abrasion.

MATERIALS AND METHODS

PubMed papers published from January 01, 2000 to September 01, 2021 were included, and keywords used were: filler particle size, shape, amount of dental composites; finishing/polishing, gloss/roughness, and toothbrush abrasion of composites. Seventy-five in-vitro studies were included in this literature review. Forty-six articles assessed filler particle size/composition/shape and distribution to obtain high gloss/smoothness on different formulations; and the finishers/polishers effect on these materials. Twenty-nine papers assessed toothbrush abrasion of composites.

RESULTS

Suprananofill/nanofill/microfills typically showed the smoothest and glossiest surfaces compared to nanohybrid, microhybrid and hybrid composites. Microfill (0.04-0.07 μm, 71-88 GU); suprananofill (0.001-0.8 μm, 52-92 GU), microhybrids (0.05-0.35 μm, 35-95 GU) and nanohybrids (0.05-0.21 μm, 66-97 GU). Composites with small, spherical particles tend to show smoother, glossier surfaces and more wear resistant compared to resin composites with larger or irregular particles. Several studies showed higher roughness and reduced gloss after toothbrush abrasion.

CONCLUSIONS

Within the limitations of this study, suprananofill/nanofill/microfill composites tended to show the smoothest/glossiest surfaces due to smaller particle size. Composites with small, spherical particles tended to show smoother/glossier surfaces. Overall, toothbrush abrasion showed higher surface roughness and reduced gloss.

CLINICAL SIGNIFICANCE

Suprananofills/nanofills/microfills had good polishability and polish retention due to their smaller particle size. The effectiveness of a polishing system is material-dependent. In general, Enhance-PoGo, Sof-Lex discs, and Sof-Lex Spiral wheels showed similar level of smoothness.

Influence of Toothbrush Abrasion and Surface Treatments on Roughness and Gloss of Polymer-Infiltrated Ceramics

The aim of this study was to compare the surface roughness and gloss of polymer-infiltrated ceramics after simulated in vitro toothbrushing in different storage mediums. Four polymer- infiltrated ceramics were evaluated, Lava ultimate (LU), Vita enamic (EN), Shofu (SH), and Crystal ultra (CU). The control group was a feldspathic ceramic, Vita Mark II (VM). One hundred and twenty specimens (12 × 14 × 2.5 mm) were prepared using a precision saw. For each material (n = 24), the specimens were allocated into two groups, polished and stained. The specimens of each group were stored (for 7 days) in either citric acid (0.2N) or distilled water. Data for surface gloss (ΔE*_SCE-SCI) and roughness (Ra) were evaluated before (baseline) and after simulated toothbrushing. For toothbrushing simulation, a toothpaste slurry containing a toothpaste of 100 relative dentin abrasion (RDA) and 0.3 ml distilled water was used for 3650 cycles (7300 strokes) for each specimen. Data were analyzed using t-test and ANOVA. A p-value of ≤ to 0.05 was considered significant. The highest mean value of surface gloss was identified in CU (stained—water) (4.3 (0.47)) (ΔE*) and EN (stained—acid) (4.3 (1.00)) (ΔE*) specimens, whereas the lowest mean value was shown by SH (stained—acid) (2.04 (0.42)) (ΔE*) samples. The highest mean value of surface roughness was observed in SH (0.40 (0.99)) Ra (stained—acid) whereas the lowest in VM (0.13 (0.039)) Ra (polished— water). A significant difference (p < 0.05) was observed in surface roughness and gloss between the materials with simulated toothbrushing, except in VM and LU, respectively. Therefore, it can be concluded that simulated toothbrushing impacts on surface roughness and gloss, irrespective of the storage medium.

Fabrication and characterization of remineralizing dental composites containing calcium type pre-reacted glass-ionomer (PRG-Ca) fillers

OBJECTIVE

To fabricate and characterize dental composites with calcium type pre-reacted glass-ionomer (PRG-Ca) fillers.

METHODS

PRG-Ca fillers were prepared by the reaction of calcium fluoroaluminosilicate glass with polyacrylic acid. Seven dental composites were produced from the same organic matrix (70/30wt% Bis-GMA/TEGDMA), with partial replacement of barium borosilicate (BaBSi) fillers (60wt%) by PRG-Ca fillers (wt%): E0 (0) - control, E1 (10), E2 (20), E3 (30), E4 (40), E5 (50) and E6 (60). Enamel remineralization was evaluated in caries-like enamel lesions induced by S. mutans biofilm using micro-CT. The following properties were characterized: degree of conversion (DC%), roughness (Ra), Knoop hardness (KHN), flexural strength (FS), flexural modulus (FM), water sorption (W_sp), water solubility (W_sl), and translucency (TP). Data were analyzed to one-way ANOVA and Tukey's HSD test (α=0.05).

RESULTS

All composites with PRG-Ca induced enamel remineralization. E0 and E1 presented similar and highest DC% than E2=E3=E4=E5=E6. Ra and KHN were not influenced by PRG-Ca fillers (p<0.05). The higher the content of PRG-Ca, the lower FS, FM and TP (p<0.05). W_sp increased linearly with the content of PRG-Ca fillers (p<0.05). E6 presented the highest W_sl (p<0.05), while the W_sl of the other composites were not different from each other (p>0.05).

SIGNIFICANCE

Incorporation of 10-40wt.% of PRG-Ca fillers endowed remineralizing potential to dental composites without jeopardizing the overall behavior of their physicochemical properties. Dental composites with PRG-Ca fillers seems to be a good alternative for reinforcing the enamel against caries development.

Colour stability and surface properties of high-translucency restorative materials for digital dentistry after simulated oral rinsing

High-translucency restorative materials are commonly used in the restoration of anterior teeth where aesthetics is a critical factor. In this in vitro study, the impact of mouthwash on the colour stability and surface characteristics of high-translucency computer-aided design and computer-aided manufacturing (CAD-CAM) dental restorative materials was evaluated. Two-hundred specimens were fabricated from five high-translucency CAD-CAM materials: a resin nano ceramic; a polymer-infiltrated ceramic network; a feldspathic ceramic; a lithium disilicate glass ceramic; and high-translucency zirconia. Each group of ceramic specimens was then divided into four subgroups: conventional mouthwash (LISTERINE); whitening mouthwash (LISTERINE Healthy White); chlorhexidine gluconate; and distilled water. Oral rinsing was simulated at 100 rpm for 180 h, representing 15 yr of clinical simulation. The specimens were then evaluated for colour, translucency, gloss, roughness, and surface morphology. Two-way ANOVA and linear mixed models were used for intergroup comparisons (α = 0.05). The polymer-infiltrated ceramic network and feldspathic ceramic became brighter, more opaque, less glossy, and rougher after rinsing with the whitening mouthwash. The long-term use of specific mouthwashes can cause deterioration of the optical and surface properties of high-translucency CAD-CAM dental restorations.

Surface Roughness of Different Composite Resins after Application of 15% Carbamide Peroxide and Brushing with Toothpaste: An In-Vitro Study

Objectives:

This study aimed to evaluate the effect of toothbrushing after application of 15% carbamide peroxide (CP) on the surface roughness of three types of composite resins.

Materials and Methods:

Twenty samples, measuring 4 mm in height and diameter, were fabricated of three composite resins namely microfilled (MF) Heliomolar HB, nanohybrid (NH) IPS Empress Direct and microhybrid (MH) Tetric Ceram HB. After polishing, the initial surface roughness was measured with a profilometer. The tray technique was used to apply 15% CP gel for 6 hours. Then, cleaning was carried out with an Oral-B electric toothbrush for 3 minutes in a tank containing a freshly mixed toothpaste. These procedures were repeated for 21 days. Then, the surface roughness was measured again and compared with the initial values. A mixed-design ANOVA model was used for the analysis of data (P<0.05).

Results:

The baseline roughness was significantly lower in MF compared to the NH and MH composites (P<0.001). Roughness increased in all study groups during the intervention period; however, this increase was not significant in the MH group (P=0.17). Furthermore, the increase in roughness in MF was smaller than that in NH (P<0.001) and MH (P=0.02) groups.

Conclusion:

The effect of intervention was more pronounced on NH and MH groups. Surface roughness changes were minor in MF composite resin.

The Effect of Desensitizing Toothpastes and Coffee Staining on the Optical Properties of Natural Teeth and Microhybrid Resin Composites: An In-Vitro Study

Objective

To evaluate the effect of different desensitizing toothpastes and coffee staining on the discoloration rate of natural human tooth and composite materials.

Materials and Methods

A total of 56 human teeth and 56 composite specimens were used. After initial color measurements were taken, specimens and teeth were exposed to simulated toothbrushing with six desensitizing toothpastes containing different active ingredients: stannous fluoride, strontium acetate, potassium citrate and hydroxyapatite, cetylpyridinium chloride, arginine, and novamin. Specimens were then exposed to coffee staining. Throughout the staining procedure, the storing solution was refreshed every day and the specimens were brushed with the tested toothpastes. Color measurements and changes were recorded at each stage and analyzed with one-way ANOVA, Dunnett tests, and paired sample t-test (p<0.05).

Results

The largest color change was obtained with the stannous fluoride toothpaste after coffee staining for natural teeth (2.6 ΔE ₀₀ ^⁎) and composite specimens (3.1 ΔE ₀₀ ^⁎). Coffee staining resulted in significant changes for ΔE ₀₀ ^⁎ values of all groups, except for natural teeth brushed with a novamin-based (p= 0.06) toothpaste. For composite specimens, only the stannous fluoride and cetylpyridinium chloride-based toothpastes resulted in significant color changes relative to the control group. ΔL^⁎ and Δb^⁎ values were also increased after staining for all groups (p<0.05).

Conclusions

Desensitizing toothpastes alone did not cause perceptible color changes; however, in combination with coffee staining, it tended to increased discoloration for both composites and natural teeth.

Assessing staining resistance of a CAD/CAM interpenetrating network composite material

Background

Color change of dental materials over time because of staining agents has important effects on the long-term prognosis of dental esthetic treatments. In the present study, staining resistance of an interpenetrating network composite material with different translucency levels (translucent and high translucent) and various surface procedures for finishing were investigated.

Methods

Same shade CAD/CAM interpenetrating network composite specimens having two different translucency levels were prepared using by a water cooling cutting saw. Specimens were grouped and different finishing procedures were performed. Then, specimens were kept in distilled water, red wine and coffee for different periods. Color was evaluated before and after exposure to staining liquids using a clinical spectrophotometer.

Results

In the 7 days Glaze group (ΔE₀₀ > 2.2), color difference was only perceivable in the specimens kept in red wine. In the 28 days red wine high translucent groups, only the high translucent Clinical group showed a clinically acceptable (ΔE₀₀ < 2.2) color change. In the translucent groups kept in red wine, only the translucent Glaze group showed a clinically perceivable color change (ΔE₀₀ > 2.2). In the 28 day measurements, all the translucent groups showed a clinically perceivable color change (ΔE₀₀ > 2.2). Of the translucent groups kept in coffee for 28 days, it was observed that only the translucent Clinical group demonstrated a clinically non-perceivable color change (ΔE₀₀ < 2.2).

Conclusions

All the translucent groups kept in red wine showed a clinically perceivable color change after 28 days. Only the high translucent Clinical Kit group showed a clinically acceptable color change. Among high translucent and translucent specimens kept in coffee only the translucent Clinical group showed a clinically acceptable color change after 28 days.

Surface deterioration of monolithic CAD/CAM restorative materials after artificial abrasive toothbrushing

PURPOSE

The purpose of this in vitro study was to evaluate the effect of abrasive toothbrushing on the surface properties of monolithic computer-assisted design and computer-assisted manufacturing (CAD/CAM) materials stored in food-simulating liquids (FSLs).

MATERIALS AND METHODS

Fourty-eight disk-shaped test specimens of each material (Paradigm MZ100/PMZ, Lava Ultimate/LU, Vita Enamic/VE, and Vita Mark II/VMII) with a diameter of 10.0 mm and a thickness of 3.0 ± 0.05 mm were prepared. Specimens were divided into 4 subgroups (n=12) and stored in air, distilled water, 0.02 M citric acid, or 75% ethanol/water solution for 7 days at 36.5℃. Then, the specimens were brushed in a multi-station brushing machine under a vertical load of 2.0 N for 3 hours. Surface gloss (GU), roughness (Ra), and hardness (Vickers [VHN]) were measured after storage and brushing simulation. The data sets were statistically analyzed with 2 and 3-way ANOVAs followed by the Tukey's post-hoc comparisons (α=.05).

RESULTS

Statistically significant difference was found among the materials concerning the results of surface properties. VMII showed the highest VHN, while PMZ produced the lowest. Storage in FSLs significantly affected the VHN of PMZ and LU. VMII showed the lowest Ra and highest GU irrespective of FSLs and of abrasive toothbrushing. VE, LU, and PMZ produced significant decrease in GU and increase in Ra after toothbrushing.

CONCLUSION

Surface properties of monolithic CAD/CAM restorative materials were differently affected by the storage media and abrasive toothbrushing.

Evaluation of ex vivo effectiveness of commercial desensitizing dentifrices

BACKGROUND

Dentin hypersensitivity is a short, severe pain with fast onset. Therapy aims to either prevent or decrease neural transmission or physically occlude the dentinal tubules. This study aimed to evaluate the effectiveness of commercial desensitizing dentifrice by means of an ex vivo method.

MATERIAL AND METHODS

Samples (n=8 lower human premolars for each group) were randomly allocated into: G1- brushing with Colgate®Sensitive Pro-Relief; G2- brushing with Sensodyne®Rapid Relief; G3- brushing with Sensodyne®Repair & Protect; and G4- brushing with Colgate®Maximum Cavity Protection. The test bodies were submitted to simulated toothbrushing and dentifrices were analyzed regarding their hydrodynamic size, polydispersity index (PI) and zeta potential. Specimens were evaluated using: scanning electron microscopy (SEM); spectroscopy energy dispersive X-ray (EDS); and profilometry. A qualitative analysis of the photomicrographs and topographies was performed.

RESULTS

The dentifrices showed statistical similar physical and chemical characteristics. They also demonstrated obliteration of dentinal tubules when micrographs were observed. Regarding the chemical elements present in the dentin samples, there was a statistically significant difference between the control and experimental surfaces in the four groups.

CONCLUSIONS

Joint data analysis shows that the desensitizing dentifrice showed better results with regards to the obliteration of dentinal tubules compared to positive and negative controls. Key words:Dentin hypersensitivity, dentin desensitizing agents, toothpastes.

Influence of Mechanical and Chemical Degradation in the Surface Roughness, Gloss, and Color of Microhybrid Composites

AIM

The aim of this study was to investigate the association of different degradations on the roughness, gloss, and color changes of microhybrid composites.

MATERIALS AND METHODS

Ten specimens were prepared for Charisma, Amelogen Plus, Point 4, and Opallis resins. Surfaces were polished and baseline measurements of roughness, gloss, and color were recorded. Specimens were then submitted to chemical and mechanical challenges, and the specimens were reevaluated. Roughness and gloss were analyzed by Kruskal -Wallis and Dunn's test (p < 0.05). Color change (ΔE) was analyzed by one-way analysis of variance and Tukey's tests (p < 0.05). The initial and final data were compared using the Wilcoxon test (p < 0.05). Spearman test checked the correlation between the roughness and gloss (p < 0.05).

RESULTS

Regarding surface roughness and gloss, there was no difference between composites before challenges. However, all composites showed a significant increase of roughness after challenges, with highest values for Charisma. The gloss was influenced by challenges, evidencing the best gloss for Point 4. Charisma showed the highest value of color change. There was no correlation between surface roughness and gloss for the initial analysis, and after the challenges.

CONCLUSION

Composites were influenced by association of challenges, and Charisma showed the highest changes for roughness, gloss, and color.

CLINICAL SIGNIFICANCE

The type of composite resin influenced the properties of materials, which are surface roughness, gloss, and color change. The dentist should be aware of the performance of different brands, to choose the correct required composite resin for each type of patient or region to be restored.

Evaluation of staining and color changes of a resin infiltration system

OBJECTIVE

To analyze the staining and color changes of a resin infiltrant system used for management of white spot lesions (WSLs).

MATERIALS AND METHODS

WSLs were artificially created on left buccal halves of 48 extracted human teeth. These sites were then treated with resin infiltration (RI) while the right halves of the teeth remained as nonresin (NRI) areas. Six groups were formed (n = 8 teeth/group) and were exposed to the following: red wine, coffee, orange juice, combined staining agents, accelerated aging, and distilled water for 1 week. The teeth were then polished with a prophy cup and polishing paste. Color properties were assessed using a spectrophotometer at baseline (T0), after each exposure (T1), and after polishing (T2). Color difference (ΔE*) was calculated between each time point for both halves of the teeth (RI and NRI). Data were analyzed with a two-way analysis of variance with presence of resin infiltration and staining agents as the main effects for each time point pair. Multiple comparisons were made with a Bonferroni post hoc test. The level of significance was set at P < .05.

RESULTS

The red wine and combined staining agent groups caused the greatest color change between all intervals (P < .05). Significant interactions were recorded between resin infiltration application and staining agents at all time periods (P < .05). The presence of resin infiltration as a main effect did not affect color change between T0 and T2 (P > .05).

CONCLUSIONS

RI areas showed higher staining susceptibility than did NRI areas. However, prophylaxis had a strong effect on reversing the discoloration of both RI and NRI areas.

Roughness Analysis on Composite Materials (Microfilled, Nanofilled and Silorane) After Different Finishing and Polishing Procedures

The finishing and polishing of composite materials affect the restoration lifespan. The market shows a variety of finishing and polishing procedures and the choice among them is conditioned by different factors such as the resulting surface roughness. In the present study, 156 samples were realized with three composite materials, -microfilled, nanofilled and silorane-, and treated with different finishing and polishing procedures. Profilometric analyses were carried out on the samples’ surface, the measured roughness values were submitted to statistical analysis. A complete factorial plan was drawn up and two-way analysis of variance (ANOVA) was carried out to investigate whether the following factors affect the values of roughness: (i) material; (ii) polishing/finishing procedure. Tukey post-hoc test was also conducted to evaluate any statistically significant differences between the material/procedure combinations. The results show that the tested materials do not affect the resulting surface quality but roughness values depend on the finishing/polishing procedure adopted. The procedures that involve: (a) the finishing with medium Sof-Lex discs and (b) the finishing with two tungsten carbide multi-blade milling cutters Q series and UF series are those that allow the lowest values of roughness to be obtained.

Surface Texture and Optical Properties of Self-Adhering Composite Materials after Toothbrush Abrasion

This study evaluated the surface texture and optical properties of two self-adhering composites and a nanofilled composite before and after toothbrush abrasion. Vertise Flow (Kerr), Fusio Liquid (Pentron Clinical) and Filtek Z350 XT (3M ESPE) composites were divided into 3 groups (n = 6). Disks of 12 mm diameter and 2 mm thick were made. All materials were light-cured with a LED light source for 40 seconds. Analyses of surface roughness, gloss retention and color stability were performed 24 hours after light curing and after 20,000 brushing cycles. Data were analyzed with analysis of variance (ANOVA) and Tukey's test (α = 5%).

RESULTS

Tukey's test ascertained that toothbrush abrasion resulted in rougher and matte surfaces for all composites tested. Filtek Z350 presented better gloss retention after abrasion. On surface roughness evaluation, there was no statistical difference between Fusio Liquid Dentin and Filtek Z350 resins (p > 0.05). Vertise Flow resin showed better color stability (ΔE), than the other two materials.

CONCLUSION

Nanofilled material presented better gloss retention but it did not produce the best results in aspects related to surface roughness and color stability compared to self-adhering composites.

CLINICAL SIGNIFICANCE

A simulation of degradation process by using toothbrush abrasion produced a rougher and matte surface in all composites tested. The surface texture was not only related to filler's amount present in materials, but also with the organic matrix composition of them. The results suggested that the constant development of new materials, seeking for a technical simplification, seems an innovative attraction for dentist's clinical routine, even though larger studies are necessary to promote to everyone a better understanding and improvement of action and effectiveness of this new class of materials.