Achieving the desired colour in discoloured teeth, using leucite-based CAD-CAM laminate systems

Effects of porcelain layer thickness and luting resin cement on the opalescence properties of porcelain veneers

BACKGROUND

When discolored teeth are repaired with porcelain veneers, the thickness of the restorations should be increased appropriately using opaque porcelain and bonded by applying opaque luting resin cement to cover discolored substrates. However, its impact on the opalescent performance has not been reported yet.

PURPOSE

To analyze the effects of opacity, body porcelain layer thickness, and luting resin cement on the opalescence properties of porcelain veneer restorations for discolored teeth.

METHODS

Ninety IPS d. SIGN A3 porcelain veneer specimens were prepared via powder-paste coating and sintering. Specimens were divided into three groups according to ceramic type and cement used or not: body porcelain group as control, body/opaque porcelain group and body/opaque porcelain-resin cement composite group. Each group was subdivided into three subgroups based on the thickness, 0.50, 0.75, and 1.00 mm (n = 10). Variolink N Bleach XL luting resin cement with thickness of 0.1 mm was applied to the bottoms of body/opaque porcelain specimens to produce body/opaque porcelain-resin cement composites. The opalescence (OP) values were calculated and the micromorphological characteristics were analyzed by scanning electron microscope (SEM). Statistical analysis was performed by using ANOVA test (P < 0.05).

RESULTS

The opalescence values determined for the body porcelain groups with thicknesses of 0.50, 0.75, and 1.00 mm and body/opaque porcelain specimens with thicknesses of 0.45/0.05, 0.70/0.05, and 0.95/0.05 mm were 3.35 ± 0.15, 3.83 ± 0.10, 6.73 ± 0.25, 7.95 ± 0.34, 15.16 ± 0.60, and 16.49 ± 0.89, respectively. The specimens in the body and body/opaque porcelain groups exhibited significant increases in their opalescence values with increasing thickness (P = 0.00). The opalescence values of the specimens increased significantly with the addition of a 0.05 mm opaque porcelain layer (P = 0.00). The opalescence values of the composites containing body/opaque porcelain layers with thicknesses of 0.45/0.05, 0.70/0.05, and 0.95/0.05 mm and luting resin cement were 9.46 ± 0.17, 16.47 ± 0.15, and 18.38 ± 0.47, respectively. The opalescence values of the composite specimens increased significantly with an increase in the thickness of the porcelain layer(P = 0.00).

CONCLUSIONS

The opaque porcelain layer and opaque resin cement can significantly improve the opalescence properties of porcelain laminate veneers for discolored teeth, but the opalescence performance is still poor than natural teeth. The body porcelain only contributes to opalescence within a certain thickness range.

Masking ability of CAD-CAM resin-matrix ceramics with different translucencies and thicknesses combined with four cement shades against varying background colors when facing veneer restorations

BACKGROUND

To evaluate the comprehensive effect of translucency, thickness, cement shades, and background color on the masking ability of resin-matrix ceramic veneer restorations.

METHODS

Resin-matrix ceramic specimens with 2 translucencies (LT, HT) and 3 thicknesses (0.5, 1.0, and 1.5 mm) were made of Upcera Hyramic (A2 shade). Cement specimens were made of Variolink N in 4 shades (yellow, white, transparent, and bleach XL). Five background specimens were made of IPS Natural Die Material in 5 shades (ND1, ND2, ND3, ND4, and ND5). Color coordinates of 120 subgroups (n = 5) of combined specimens composed of different ceramic, cement, and background specimens were obtained using a spectroradiometer. Color difference (ΔE00) compared with a 4-mm thick specimen of LT and HT ceramics was calculated and four-way ANOVA was used for statistical analysis (α = 0.05).

RESULTS

Translucency, thickness, cement shade, background color, and their interaction had significant effects on ΔE00 (p < 0.001). ΔE00 values of HT groups were always higher than that of LT groups and were greater than 1.8 against all background colors. ΔE00 values of LT groups could be achieved to be less than 1.8 with appropriate thickness and cement shade. ΔE00 value decreased with increasing ceramic thickness. The effect of cement shade on ΔE00 had no obvious regularity, but ΔE00 values of bleach XL cement shade group were always lower than other cement shade groups under ND3 and ND5 background color.

CONCLUSIONS

The masking ability of CAD-CAM resin-matrix ceramics can be simultaneously affected by translucency, thickness, cement shade, and background color. Resin-matrix ceramics with low translucency has a better masking ability than that with high translucency. The masking ability of CAD-CAM resin-matrix ceramics increase with increasing thickness. Cement shade has less impact on the final color of resin-matrix ceramic restorations.

Effects of ultraviolet weathering aging on the color stability and biocompatibility of various computer-aided design and computer-aided manufacturing glass-ceramic materials

OBJECTIVES

This study assessed the changes in color stability and biocompatibility of computer-aided design and computer-aided manufacturing (CAD-CAM) glass-ceramics after ultraviolet weathering (UW) aging.

METHODS

A total of 300 plate-shaped specimens (12.0 × 14.0 × 1.5 mm3) were prepared using a leucite-reinforced glass-ceramic (IPS Empress CAD; E), a lithium disilicate (IPS e.max CAD; M), and two zirconia-reinforced lithium silicate (Celtra Duo; C, Vita Suprinity; V) glass-ceramics. Specimens were divided into three groups (n = 25, each), subjected to water storage at 37 °C for 24 h (control group), or UW aging at 150 kJ/m2 (first-aged group) or 300 kJ/m2 (second-aged group). The color stability, mechanical and surface properties, and biocompatibility of the CAD-CAM glass-ceramics were investigated experimentally, followed by statistical analysis.

RESULTS

The brightness and redness or greenness were reduced in all groups after aging. After the first aging, V exhibited the largest color change and E exhibited the smallest color change. After the second aging, E exhibited the highest nanoindentation hardness and Young's modulus. The surface roughness was the highest for V after the first aging. Furthermore, the hydrophilicity of the materials increased after aging process. The cell proliferation/viability of human gingival fibroblasts was the highest in E before and after aging. Almost all cells survived for all groups based on a live/dead assay.

CONCLUSIONS

Leucite-reinforced glass-ceramic exhibit the highest color stability and biocompatibility after aging. The color stability and biocompatibility of CAD-CAM glass-ceramics depend on the aging process and material type.

CLINICAL SIGNIFICANCE

Various CAD-CAM glass-ceramics exhibit adequate color stability after UW aging. The leucite-reinforced glass-ceramics exhibit the highest color stability, cell proliferation, and viability after aging. The color stability, mechanical and surface properties, and biocompatibility of the glass-ceramics depend on the aging process and material type.

Optical properties of esthetic temporary cements and final restoration color

BACKGROUND

Opaque cements can be esthetically unfavorable and alternative translucent materials have been developed. The aim of this study was to evaluate the color interference of a new translucent cement compared with conventional materials, in association with interim restoration with different thickness and shades.

METHODS

Bis-acryl composite disks were prepared in 2 thicknesses (1.2 mm, 0.6 mm) and 3 shades (A3.5, A2, bleached) to simulate the restorations. Cementation over dentin disks was performed with 1 translucent cement (Provicol QM Aesthetic; VOCO), 2 conventional cements (Provicol; VOCO, Temp-Bond NE; Kerr Dental), and 1 transparent liquid (polyethylene glycol 400). The difference between the color of the specimens cemented with the transparent liquid and that of the specimens cemented with each cement was calculated (ΔEab). The data were analyzed using 3-way analysis of variance and Tukey tests (5%).

RESULTS

Significant differences were observed for all factors and some interactions (P < .05). For Provicol QM Aesthetic, the shade and thickness did not influence the ΔEab. For Provicol and Temp-Bond NE, the lighter and thinner the specimen, the higher the ΔEab. Only Provicol QM Aesthetic had smaller means than the perceptibility threshold. Temp-Bond NE and Provicol had higher values than the acceptability threshold for some combinations.

CONCLUSIONS

The highly translucent cement had less color interference than the conventional materials. The thickness and resin shade only affected the results for the opaque cements. The thinner specimens and the lighter shades had higher color interference.

PRACTICAL IMPLICATIONS

The use of a more translucent cement can produce a smaller color interference on the esthetic outcome of interim restorations.

Effect of ceramic primers with different chemical contents on the shear bond strength of CAD/CAM ceramics with resin cement after thermal ageing

BACKGROUND

This study evaluated the effect of ceramic primers containing 10-methacryloyloxydecyl phosphate (10-MDP) and γ-methacryloxypropyl trimethoxysilane (γ-MPTS) agents on the shear bond strength (SBS) of CAD/CAM ceramics with different chemical structures and resin cement.

METHODS

A total of 640 CAD/CAM ceramic specimens were obtained from Vita Mark II (VM), IPS E.max CAD (EM), Vita Suprinity (VS) and Vita Enamic (VE). The specimens were divided into two groups: etched with hydrofluoric acid (HF) and unetched. Each group was treated with a different ceramic primer (Clearfil Ceramic Primer Plus, G-Multi Primer and Monobond S), except for an untreated group (n = 10). After ceramic primers and resin cement were applied to each ceramic surface, half of the specimens were thermally aged at 10,000 cycles, 5-55 ± 1 °C, with a dwell time of 30 s. The SBS was tested with a universal testing machine at a 0.5 mm/min crosshead speed. Data were analysed by using statistical software (SPSS 20). Normal data distribution was checked with the Shapiro‒Wilk test. Three-way ANOVA was used to analyse the difference between the numeric data of the HF etched and thermally aged groups. A post hoc Tukey test was applied in the paired comparison of significant difference. The statistical significance level was accepted as p < 0.05.

RESULTS

The highest SBS values were obtained in the HF etched G-Multi primer applied nonaged EM group (28.3 ± 2.62 MPa), while the lowest values were obtained in the nonetched and thermally aged EM group that received no treatment (2.86 ± 0.04 Mpa). The SBS significantly increased in all specimens on which the ceramic primer was applied (p < 0.001). Thermal ageing had a significant negative effect on the SBS values in all groups (p < 0.001).

CONCLUSION

The positive combined effects of the 10-MDP and γ-MPTS agents resulted in a significant increase in the bonding strength of the resin cement to the CAD/CAM ceramics. In addition, the increase in the amount of inorganic filler provided a favourable effect on durable adhesion.

A Scoping Review on the Polymerization of Resin-Matrix Cements Used in Restorative Dentistry

In dentistry, clinicians mainly use dual-cured or light-cured resin-matrix cements to achieve a proper polymerization of the organic matrix leading to enhanced physical properties of the cement. However, several parameters can affect the polymerization of resin-matrix cements. The main aim of the present study was to perform a scoping review on the degree of conversion (DC) of the organic matrix, the polymerization, and the light transmittance of different resin-matrix cements used in dentistry. A search was performed on PubMed using a combination of the following key terms: degree of conversion, resin cements, light transmittance, polymerization, light curing, and thickness. Articles in the English language published up to November 2022 were selected. The selected studies' results demonstrated that restorative structures with a thickness higher than 1.5 mm decrease the light irradiance towards the resin-matrix cement. A decrease in light transmission provides a low energy absorption through the resin cement leading to a low DC percentage. On the other hand, the highest DC percentages, ranging between 55 and 75%, have been reported for dual-cured resin-matrix cements, although the polymerization mode and exposure time also influence the DC of monomers. Thus, the polymerization of resin-matrix cements can be optimized taking into account different parameters of light-curing, such as adequate light distance, irradiance, exposure time, equipment, and wavelength. Then, optimum physical properties are achieved that provide a long-term clinical performance of the cemented restorative materials.

Porcelain Veneers in Vital vs. Non-Vital Teeth: A Retrospective Clinical Evaluation

Nowadays, the ceramic veneer approach can be considered more predictable than direct composite veneer. To date, there is a lack of studies comparing the clinical performance of anterior veneers cemented on vital teeth (VT) and non-vital teeth (NVT). This longitudinal clinical study investigated the performance of ceramic veneers in VT or anterior NVT. A total of 55 patients were evaluated in the study. Two groups were defined based on the vitality status of the teeth (93 teeth-vital and 61 teeth-non-vital). The United States Public Health Service (USPHS) criteria were used to assess the clinical status. The data were evaluated statistically with the Mann-Whitney U test. All restorations were considered acceptable, and only one veneer in VT failed for the criteria of secondary caries. There were no statistically significant differences in any of the criteria evaluated (p ≤ 0.671). The ceramic veneers evaluated showed a satisfactory clinical performance both in VT and NVT.

Using artificial intelligence to predict the final color of leucite-reinforced ceramic restorations

OBJECTIVES

The aim of this study was to evaluate the accuracy of machine learning regression models in predicting the final color of leucite-reinforced glass CAD/CAM ceramic veneer restorations based on substrate shade, ceramic shade, thickness and translucency.

METHODS

Leucite-reinforced glass ceramics in four different shades were sectioned in thicknesses of 0.3, 0.5, 0.7, and 1.2 mm. The CIELab coordinates of each specimen were obtained over four different backgrounds (black, white, A1, and A3) interposed with an experimental translucent resin cement using a calibrated spectrophotometer. The color change (CIEDE2000) values, as well as all the CIELab values for each one of the experimental groups, were submitted to 28 different regression models. Each regression model was adjusted according to the weights of each dependent variable to achieve the best-fitting model.

RESULTS

Different substrates, ceramic shades, and thicknesses influenced the L, a, and b of the final restoration. Of all variables, the substrate influenced the final ceramic shade most, followed by the ceramic thickness and the L, a, and b of the ceramic. The decision tree regression model had the lowest mean absolute error and highest accuracy to predict the shade of the ceramic restoration according to the substrate shade, ceramic shade and thickness.

CLINICAL SIGNIFICANCE

The machine learning regression model developed in the study can help clinicians predict the final color of the ceramic veneers made with leucite-reinforced glass CAD/CAM ceramic HT and LT when cemented with translucent cements, based on the color of the substrate and ceramic thicknesses.

Effects of background color and thickness on the optical properties of CAD-CAM resin-matrix ceramics

STATEMENT OF PROBLEM

Information regarding the masking ability of computer-aided design and computer-aided manufacture (CAD-CAM) resin-matrix ceramic materials with different compositions is scarce.

PURPOSE

The purpose of this in vitro study was to evaluate the effects of background color and thickness on the optical properties (color and translucency) of CAD-CAM resin-matrix ceramics.

MATERIAL AND METHODS

Twelve rectangular specimens were fabricated at a different thickness (1, 1.5, and 2 mm) (n=12) from each of the resin-matrix ceramic materials: Shofu block (SB), Lava Ultimate (LU), CERASMART (CS), VITA ENAMIC (VE), Crystal Ultra (CU), and the VITABLOCS Mark II feldspathic ceramic (VB). The color of the specimens over amalgam, titanium, enamel, and dentin backgrounds was measured with a spectrophotometer, and the color differences (ΔE∗ab) were calculated by using the Commission Internationale de l'Eclairage (CIE) 76 formula. The difference in color of the specimen over the black and white backgrounds was used to calculate the translucency parameter (TP). ANOVA was used to statistically test whether material, background, and thicknesses influenced ΔE∗ab and TP values. Post hoc comparisons were performed to determine the significant difference among the groups (α=.05).

RESULTS

The interaction with 2 between factors demonstrated that the material was a factor that significantly influenced ΔE∗ab (P<.001). The highest mean ±standard deviation of ΔE∗ab was recorded in the combination of VB material and 2-mm thickness (1.84 ±0.37), and the lowest with CS material with 1.5-mm thickness (0.47 ±0.24). The type of material and specimen thickness significantly influenced TP (P<.001). The highest and lowest mean ±standard deviation of TP were recorded for the 1-mm-thick CS (14.20 ±0.90) and 2-mm-thick SB (4.91 ±0.42) specimens, respectively.

CONCLUSIONS

CERASMART resin-matrix ceramic and VITABLOCS Mark II feldspathic ceramic exhibited high and low masking abilities over the investigated background substrates, respectively. However, irrespective of the thickness, all study materials exhibited acceptable masking abilities.

Final Colour of Ultratranslucent Multilayered Zirconia Veneers, Effect of Thickness, and Resin Cement Shade

Background

Aesthetic restorations should be able to mimic the natural colour depth of teeth, affected by several factors including material properties. There is a lack of information regarding the effect of cement shade and material thickness on the final colour of ultratranslucent multilayered zirconia veneers.

Objectives

This study evaluated the effect of ceramic thickness and resin cement shade on the final colour of different layers of ultratranslucent multilayered (UTML) zirconia veneers.

Methods

This in vitro study produced 90 rectangular-shaped specimens with nonsintered Katana UTML monolithic zirconia (Kuraray Noritake Dental, Tokyo, Japan), shade A1 blocks. Ceramic samples were prepared in two groups of 0.7 mm and 0.5 mm thicknesses, 45 of each (a: 8 × 11 × 0.5 mm; b: 8 × 11 × 0.7 mm). Specimens of each thickness were further divided into 5 groups: universal, clear, brown, white, and opaque (n = 9). Each adhesive resin cement (Panavia V5) was applied between the ceramic samples and composite substrate. The colour values were measured using a spectrophotometer in baseline and after resin cement application according to the CIELab system. For all samples, ΔE00 values were obtained. Data were evaluated with SPSS 25 using the three-way ANOVA test (p < 0.05).

Results

The factors of cement shade, ceramic thickness, and ceramic layers have statistically significant effect on ΔE00 values (p < 0.001). The results showed lower ΔE00 values with thicker ceramic veneers. Tukey test results showed that the opaque and brown shade had a significantly greater ΔE00 values comparing to universal (p = 0.004), clear, and white shades (p < 0.001).

Conclusion

The colour change was greater in lower ceramic thickness. Different shades of resin cement and layers of UTML zirconia differently affected the final colour.

Masking Abilities of Dental Cad/Cam Resin Composite Materials Related to Substrate and Luting Material

An outstanding treatment challenge related to aesthetic monolithic materials is to mask discolored substrates in aesthetic areas. The purpose of the study is to evaluate the substrate masking ability of different resin composite materials and the influence of their association with luting agents and substrates. Five types of 2M2 HT (high translucency) resin composite materials were selected: Vita Enamic [E] and four types of nanoparticle-filled composites Lava Ultimate [L], Cerasmart [C], Shofu HC [S], and Hyramic [H]. Resin composite Vita VM LC with different shades was used for the substrates: 2M2, 3M2, and CP2. Variolink Esthetic Try-inpastes neutral, light+, and warm+ colors were chosen to simulate the luting agent color. Optical parameters (TP (translucency), CR (contrast ratio), and OP (opalesce)) and color differences ΔE (chromatic difference) were calculated. Statistical analyses were performed to evaluate the comparisons between the groups and establish correlations. TP average values for all materials were in the range of 21.49–24.53. OP average values were in the rage of 6.31–7.85. OP is moderate positive correlated to TP and CR is negative and strong correlated to TP. Related to materials, average color changes decrease as following: E > H > C > L > S. Referring to the tryin material, warm colors induce marked color changes of the restoration. The differences of the color changes determined by all studied substrates are significant. For the final aesthetic aspect of the restoration, it is essential to consider the underlying dental structure, luting agent, and restoration material as a whole unit. The masking ability of the investigated resin matrix ceramic materials materials shows differences, the best behavior demonstrated Shofu HC and Lava Ultimate. Marked color changes are related to high chroma substrates. For substrates with a darker color, the association with warm try-in pastes lead to marked color changes, but with neutral and light try-in pastes at most perceivable.

Effect of CAD-CAM ceramic materials on the color match of veneer restorations

STATEMENT OF PROBLEM

With the different translucency levels and types of computer-aided design and computer-aided manufacturing (CAD-CAM) ceramic materials, choosing the most appropriate CAD-CAM ceramic materials to better reproduce the color appearance of natural teeth can be challenging.

PURPOSE

The purpose of this in vitro study was to analyze the color differences between natural teeth and milled veneers fabricated with the different types of CAD-CAM ceramic materials.

MATERIAL AND METHODS

Ten extracted maxillary central incisor teeth with the A2 shade in the body region were prepared for ceramic veneers. The veneer restorations were designed by using the duplicating method and fabricated from 9 milling blocks (IPS e.max CAD HT/LT, Lava Ultimate CAD HT/LT, VITA SUPRINITY HT/T, IPS Empress CAD HT/LT/Multi) in a dental milling unit (n=10). The bonding surface of the abutment tooth was coated with a thin layer of a separating agent, and the veneer specimen with resin cement was then bonded to the corresponding abutment tooth. A clinical spectrophotometer was used to measure the Commission Internationale de l'Eclairage Lab values of natural teeth, abutment teeth, and milled veneers in the cervical, body, and incisal regions. Color differences between the natural tooth and A2 shade tab (ΔE₁) and between the milled veneer and natural tooth (ΔE₂) were calculated. The ΔE₂ values were compared with the perceptibility threshold (ΔE=2.6) and acceptability threshold (ΔE=5.5). The paired-samples t test, 1-way analysis of covariance, and 2-way ANOVA were used to analyze data (α=.05).

RESULTS

The results of 1-way analysis of covariance showed that ceramic materials significantly affected the a∗ and b∗ values of the milled veneers (P<.001) but did not affect the L∗ values of the milled veneers (P>.05). The results of 2-way ANOVA indicated that the ΔE₂ values were not significantly affected by different CAD-CAM ceramic materials (F=1.560, P=.138), while statistically significant differences were found in the veneer regions (F=6.588, P=.002). The ΔE₂ values ranged from 2.41 to 5.36, less than the clinically acceptable color threshold of 5.5.

CONCLUSIONS

The color parameters of milled veneers were affected by the different types of CAD-CAM ceramic materials. The color of the veneer restoration was able to match that of the natural tooth.

The effect of resin cement shade and restorative material type and thickness on the final color of resin-matrix ceramics

PURPOSE

This study aims to evaluate the effects of cement shade, restorative material type, and thickness on the final color of resin-matrix ceramics.

METHODS

Ninety A2 shade resin-matrix ceramic specimens were prepared from Vita Enamic, GC Cerasmart, and Lava Ultimate at 0.5 and 1.0 mm thicknesses. Sixty resin cement disks were fabricated from different shades (A1, A3O, B05, and TR) of RelyX Ultimate at 0.1 mm thickness. CIE color coordinates were measured using a spectrophotometer, and color differences (∆ E 00 ) were calculated. Data were statistically analyzed (P =0.05).

RESULTS

The ΔE 00 values were influenced by the cement shade, restorative material type, thickness, and their interactions ( P < 0.05). A3O cement caused clinically unacceptable values for all groups at 0.5 mm thickness and GC at 1.0 mm thickness. A1 and TR cement shades demonstrated visually perceptible but clinically acceptable values, except for VE-A1 and LU-A1 at 0.5 mm thickness. The ∆E 00 values of the B05 cement shade were lower than the visually perceptible threshold for both thicknesses except for GC at 0.5 mm thickness.

CONCLUSIONS

The shade of the resin cement and the type and thickness of the resin-matrix ceramic material significantly affected the resulting final color. To provide a shade matching with natural dentition and to obtain esthetic restorations, especially for the anterior teeth, the resin cement shade and resin-matrix ceramic material should be carefully selected.

Effect of color of the cement and the composite resin foundation on the resultant color of resin-matrix ceramics

STATEMENT OF PROBLEM

An improper restoration color match to the adjacent natural teeth can jeopardize esthetic success. The type of resin-matrix ceramic (RMC), the shade of the underlying foundation, and the shade of cement may affect the optical behavior of RMC materials, but studies on this issue are lacking.

PURPOSE

The purpose of this in vitro study was to assess the cumulative effect of different shades of composite resin foundation (CRF) and cement on the optical behaviors of 3 different RMCs.

MATERIAL AND METHODS

Forty-five rectangular RMC specimens (14×12×1 mm, shade A2) were prepared from 3 different blocks, including a polymer-infiltrated ceramic network (Vita Enamic [VE]), a resin nanoceramic (Lava Ultimate [LU]), and a flexible nanoparticle-filled resin (GC Cerasmart [GC]) (n=15 per RMC block). CRFs (14×12×4 mm) were fabricated in white and dentin shades (n=1 per composite resin shade). Cement specimens (G-CEM LinkForce) were prepared from 3 shades (A2, opaque [OP], and translucent [TR]) (n=15 per shade). For control groups, 3 rectangular RMC foundations (14×12×4 mm) were also milled from RMC blocks (n=1 per block). Color coordinates were recorded by using a digital spectrophotometer. The coordinates of 4-mm-thick RMC foundations served as the control groups. The coordinates of RMC specimens on each combination of CRF and cement served as test groups. The CIEDE2000 (ΔE₀₀) formula was used to assess color differences. Data were subjected to 3-way ANOVA and Tukey honestly significant difference (HSD) tests (α=.05).

RESULTS

ΔE₀₀ values of specimens were influenced by the CRF shade, cement shade, RMC type, as well as the interaction terms of the 3 variables (P<.001). Color differences in groups VE-A2-dentin, VE-OP-dentin, LU-OP-dentin, and GC-OP-dentin showed perceptible but clinically acceptable values (0.8<ΔE₀₀≤1.8). The highest and lowest ΔE₀₀ values were observed in the white-OP-LU (5.32 ±0.34) and dentin-OP-VE (0.94 ±0.31) groups.

CONCLUSIONS

Opaque cement on the white foundation led to the highest ΔE₀₀ values in the resultant colors of all RMC groups. When used with the same shade on the dentin foundation, this cement produced clinically acceptable results.

[Study of masking ability of laminate veneers for discolored teeth]

OBJECTIVE

To select the most effective method among different masking treatments, such as different thickness and transparence, tissue surface's opaque coating, and opaque resin cement to restore discolored teeth esthetically by porcelain veneer.

METHODS

Four extracted intact maxillary central incisors were prepared for porcelain veneer restoration and each three heat pressed porcelain veneers from three thicknesses (0.8 mm, 1.0 mm, 1.2 mm) and two transparency(high transparence, HT and low transparence, LT))in Vita shade A2 were fabricated for each tooth, in total of 72 pieces. The surfaces of three prepared teeth were then painted to mimic situations of severe dental fluorosis, severe tetracycline teeth, and necrotic teeth. Each of the veneers was temporarily cemented to the corresponding tooth surface using try-in cements with three different colors (transparent, opaque, and yellow), then used the shade guide (3D master) and electronic colorimeter (easy shade) to record the shade of each porcelain veneer through hue, lightness, and chroma reading. After that, high-transparence porcelain veneers in thickness of 0.8 mm was fused with a layer of opaque porcelain in tissue surface, and were shade matched again after cementation. Statistic treatments were performed to analyze the difference in each masking method.

RESULTS

For each 0.2 mm increase in the veneer thickness of porcelain, the average lightness was reduced by 1 unit, while the chroma was not changed which was independent of the type of the resin cements. When the thickness of the porcelain veneer was decreased to 0.8 mm, the opacity effect was not remarkable even if a low-transparence porcelain veneer was used. Transparent and yellow resin cements had poor opaque performance, while opaque resin cement could reduce the lightness by 2 units and the chroma was also reduced. The opaque layer of the tissue surface could be applied uniformly, and the lightness and chroma could be reduced to Vita 2M1 to 2M1.5 levels regardless of the color of resin cements, which suggested a stable opacity effect for different discolored teeth in this study.

CONCLUSION

For porcelain veneer restoration of discolored teeth, thickened veneers are the most effective means to display a natural transmittance and color. Tissue surface's opacity coatings and opaque resin cements can also be used to reduce grayscale and increase lightness.

Evaluation of shade correspondence between current monolithic CAD/CAM blocks and target shade tab by considering the influence of cement shade and restorative material thickness

It was aimed to evaluate shade matching between novel CAD/CAM blocks and the A2 target shade tab by considering the influence of cement shade and restorative material thickness on the chromatic background. A total number of 120 rectangular-shaped specimens were subtracted from four different prefabricated CAD/CAM blocks [Vita Enamic (VE), Lava Ultimate (LU), GC Cerasmart (GC), and Vita Mark II (VMII)]. These specimens had thicknesses of 0.5 mm and 1.0 mm. Three different shades (A2, opaque, and translucent) of dual-polymerized resin cement were chosen. The dentin shade (A3.5) restorative composite foundation was incrementally fabricated in a silicon mold. For control group, the A2 shade tab of the Vitapan classical shade guide was used. Different restorative material-cement-foundation assemblies were generated with optic gel. Color readings were performed by using a clinical spectrophotometer, and CIEDE2000 (ΔE₀₀) formula was used to assess color differences. Data were statistically analyzed (α = 0.05). With increasing thickness, color difference values decreased. Higher mean ΔE₀₀ units were observed in all restorative material sub-groups for 0.5 mm thickness. In TR shade, no statistically significant difference was detected among the mean ΔE₀₀ values of 0.5 mm-thick restorative materials. Color differences in groups 1.0 mm-opaque-LU and 1.0 mm-opaque-GC indicated perceptible but clinically acceptable values (0.8˂ΔE₀₀ ≤ 1.8). The highest and lowest ΔE₀₀ units were observed in the 0.5 mm-A2-VE group (ΔE₀₀ = 7.07) and 1 mm-opaque-GC group (ΔE₀₀ = 1.46), respectively. Luting cement shade, restorative material type, and thickness significantly influenced the resultant color of restoration. Opaque cement on dentin foundation exhibited lower color differences.

Cement opacity and color as influencing factors on the final shade of metal-free ceramic restorations

OBJECTIVE

To investigate the influence of opacity and color of luting cements on the final shade of metal-free restorations.

MATERIALS AND METHODS

Five resin cement colors in combination with four different thicknesses of CAD/CAM ceramic materials were tested, and a composite substrate was used as dentin color reference (n = 3). Specimen color was measured with a spectrophotometer equipped with an integrating sphere before and after cementation (CIELAB). Cement and ceramic color and opacity (TP) were assessed by measuring the tested ceramic thickness as a 1-mm thick disk for each of the cement shades. The differences in color were evaluated (ΔE₀₀ ). Data were statistically analyzed by a Two-Way ANOVA followed by the Tukey Test for post-hoc comparison (P < .05) and multiple comparison Pearson's test (P < .05); the acceptability and perceptibility threshold were evaluated.

RESULTS

Statistically significant influence was found for factors ceramic thickness and cement shade (P < .001). Perceptible and unacceptable color changes were induced on the final restoration by resin cements (ranging from ΔE₀₀  = 0.69 ± 0.54 to ΔE₀₀  = 5.53 ± 0.46), the correlation between factors became strong (r²  > 0.6) in case of mismatch between color and translucency of cement and ceramic. Only the clear shade in combination with the thickest ceramic, resulted in an imperceptible color change (ΔE₀₀  = 0.69 ± 0.54).

CONCLUSIONS

The final shade of ceramic restorations can be influenced by resin cements; the magnitude of influence is related to the cement optical properties.

CLINICAL SIGNIFICANCE

In order to influence the final shade of a ceramic restoration, a cement more opaque than the restorative material should be used. Conversely, in the case of a fitting shade of the restoration, a cement more translucent than the restoration should be used to avoid undesired changes.

Color agreement between try-in paste and resin cement: Effect of thickness and regions of ultra-translucent multilayered zirconia veneers

Background. The current study aimed at identifying the color agreement between try-in pastes and the respective resin cements and investigated the effect of thickness and regions of Ultra-Translucent Multilayered Zirconia Veneers.

Methods. A total of 90 cubic zirconia discs were prepared at two different thicknesses (0.5 mm and 0.7 mm) (n=45) in five groups in terms of the shade of the try-in paste and resin cement as follows: Universal, Clear, Brown, White and Opaque. Try-in paste and the respective resin cement were applied between the specimens and composite substrate, respectively, and colorimetric evaluation was carried out using CIE-Lab system. For each specimen, ΔE between the try-in paste and cement was calculated. Data were analyzed with SPSS 17 using Multifactor ANOVA (P<0.05).

Results. Multifactor ANOVA results showed that ΔE values were significantly affected by the resin cement shade and the thickness of ceramic veneer (P<0.05). The results showed better shade agreement between the try-in paste and the respective resin cement with thicker ceramic veneers. The results of Tukey HSD revealed that ΔE values for the Clear, Universal and Brown shades were less than those of the White and Opaque shades. Lighter shades exhibited better agreement between the try-in paste and the respective resin cement.

Conclusion. Perceptible color difference was found between the try-in pastes and the respective resin cement in most colors investigated. Although, the agreement of the try-in pastes and the respective resin cement was affected by the thickness of zirconia veneers, the different regions of multilayered ultra-translucent zirconia ceramic showed no significant effect.

Comparative color and surface parameters of current esthetic restorative CAD/CAM materials

PURPOSE

The purpose of this study was to derive and compare the inherent color (hue angle, chroma), translucency (TP_SCI), surface gloss (ΔE^*_SCE-SCI), and surface roughness (R_a) amongst selected shades and brands of three hybrid CAD/CAM blocks [GC Cerasmart (CS); Lava Ultimate (LU); Vita Enamic (VE)].

MATERIALS AND METHODS

The specimens (N = 225) were prepared into square-shaped (12 × 12 mm²) with different thicknesses and shades. The measurements of color, translucency, and surface gloss were performed by a reflection spectrophotometer. The surface roughness and surface topography were assessed by white light interferometry.

RESULTS

Results revealed that hue and chroma values were influenced by the material type, material shade, and material thickness (P < .001). The order of hue angle amongst the materials was LU > CS > VE, whereas the order of chroma was VE > CS > LU. TP_SCI results demonstrated a significant difference in terms of material types and material thicknesses (P ≤ .001). TP_SCI values of the tested materials were ordered as LU > CS > VE. ΔE^*_SCE-SCI and R_a results were significantly varied amongst the materials (P < .001) and amongst the shades (P < .05). The order of ΔE^*_SCE-SCI amongst the materials were as follows LU > VE ≥ CS, whereas the order of R_a was CS ≥ VE > LU.

CONCLUSION

Nano-ceramic and polymer-infiltrated-feldspathic ceramic-network CAD/CAM materials exhibited different optical, inherent color and surface parameters.

The effect of ceramic thickness and resin cement shades on the color matching of ceramic veneers in discolored teeth

The objective of this study was to analyze the effects of ceramic material thickness and resin cement shade on the color matching of ceramic veneers at the gray tooth structures. Seventy-two artificial maxillary right central incisor teeth (C2 shade) were prepared according to veneer tooth preparation in practice. Ceramic materials (LT, A2 shade, IPS e.max Press) were selected to fabricate the 0.50- and 0.75-mm thick veneers at the body region. The ceramic veneer specimens were bonded to the artificial teeth by the 6 shades of resin cements (Variolink Veneer: shades of HV+3, LV-2, LV-3; and RelyX^TM Veneer: shades of WO, TR, A3). A clinical spectrophotometer (Crystaleye, Olympus) was used to measure the color parameters. The color differences (ΔE values) of ceramic veneers and A2 shade tab (Vitapan Classical, Vita) and C* _ab values were calculated. The results of three-way ANOVA indicated that the ΔE values of ceramic veneer and A2 shade tab were significantly different in the thickness of ceramic materials, shades of resin cements, and measuring regions (p < 0.001). There were significant differences in 0.50-mm-thick ceramic veneers that exhibited higher ΔE values compared with veneers that were 0.75-mm thick. Tukey's HSD test showed that the average ΔE values in body region were significantly smaller than that in cervical and incisal regions. The color matching of ceramic veneers was significantly influenced not only by the ceramic thickness and the resin cement shades but also the tooth regions.