Chitosan-based green sorbent material for cations removal from an aqueous environment

Insight into microplastics in the aquatic ecosystem: Properties, sources, threats and mitigation strategies

Globally recognized as emergent contaminants, microplastics (MPs) are prevalent in aquaculture habitats and subject to intense management. Aquaculture systems are at risk of microplastic contamination due to various channels, which worsens the worldwide microplastic pollution problem. Organic contaminants in the environment can be absorbed by and interact with microplastic, increasing their toxicity and making treatment more challenging. There are two primary sources of microplastics: (1) the direct release of primary microplastics and (2) the fragmentation of plastic materials resulting in secondary microplastics. Freshwater, atmospheric and marine environments are also responsible for the successful migration of microplastics. Until now, microplastic pollution and its effects on aquaculture habitats remain insufficient. This article aims to provide a comprehensive review of the impact of microplastics on aquatic ecosystems. It highlights the sources and distribution of microplastics, their physical and chemical properties, and the potential ecological consequences they pose to marine and freshwater environments. The paper also examines the current scientific knowledge on the mechanisms by which microplastics affect aquatic organisms and ecosystems. By synthesizing existing research, this review underscores the urgent need for effective mitigation strategies and further investigation to safeguard the health and sustainability of aquatic ecosystems.

An innovative approach to synthesize graft copolymerized acetylacetone chitosan/surface functionalized alginate/rutile for efficient Ni(II) uptake from aqueous medium

In this study, an innovative approach is followed to synthesize graft copolymerized chitosan with acetylacetone (AA-g-CS) through free-radical induced grafting. Afterwards, AA-g-CS and rutile have been intercalated uniformly into amino carbamate alginate matrix to prepare its biocomposite hydrogel beads of improved mechanical strength having different mass ratio i.e., 5.0 %, 10.0 % 15.0 % and 20.0 % w/w. Biocomposites have been thoroughly characterized through FTIR, SEM and EDX analysis. Isothermal sorption data showed good fit with Freundlich model as conferred from regression coefficient (R² ≈ 0.99). Kinetic parameters were evaluated through non-linear (NL) fitting of different kinetic models. Experimental kinetic data exhibited close agreement to quasi-second order kinetic model (R² ≈ 0.99) which reveals that chelation between heterogeneous grafted ligands and Ni(II) is occurring through complexation. Thermodynamic parameters were evaluated at different temperatures to observe the sorption mechanism. The negative values of ΔG° (-22.94, -23.56, -24.35 and - 24.94 kJ/mol), positive ΔH° (11.87 kJ/mol) and ΔS° (0.12 kJ/molK^-1) values indicated that the removal process is spontaneous and endothermic. The maximum monolayer sorption capacity (q_m) was figured as 246.41 mg/g at 298 K and pH = 6.0. Hence, 3AA-g-CS/TiO₂ could be better candidate for economic recovery of Ni(II) ions from waste effluents.

Parametric and kinetic studies of activated sludge dewatering by cationic chitosan-like bioflocculant BF01314 produced from Citrobacter youngae

Bacterial strains belonging to Citrobacter spp. were reported to produce polysaccharides consisting of N-acetylglucosamine and glucosamine like chitosan, with high flocculation activity. In this work, the flocculation dewatering performance of activated sludge conditioned by a novel cationic chitosan-like bioflocculant (BF) named BF01314, produced from Citrobacter youngae GTC 01314, was evaluated under the influences of flocculant dosage, pH, and temperature. At BF dosage as low as 0.5 kg/t DS, the sludge dewaterability was significantly enhanced in comparison to the raw (untreated) sludge, featuring well-flocculated characteristic (reduction in CST from 22.0 s to 9.4 s) and good sludge filterability with reduced resistance (reduction in SRF by one order from 7.42 × 1011 to 9.59 × 10¹⁰ m/kg) and increased compactness of sludge (increase in CSC from 15.2 to 23.2%). Besides, the BF demonstrated comparable high sludge dewatering performance within the pH range between 2 and 8, and temperature range between 25 °C and 80 °C. Comparison between the BF, the pristine chitosan and the commercial cationic copolymer MF 7861 demonstrated equivalent performance with enhanced dewaterability at the dosage between 2.0 and 3.0 kg/t DS. Besides, the BF demonstrated strong flocculation activity (>99%) when added to the sludge suspension using moderate to high flocculation speeds (100-200 rpm) with at least 3-min mixing time. The BF's reaction in sludge flocculation was best fitted with a pseudo first-order kinetic model. Electrostatic charge patching and polymer bridging mechanisms are believed to be the dominant mechanistic phenomena during the BF's sludge conditioning process (coagulation-flocculation).

Protective Properties of Copper-Loaded Chitosan Nanoparticles against Soybean Pathogens Pseudomonas savastanoi pv. glycinea and Curtobacterium flaccumfaciens pv. flaccumfaciens

Soybeans are a valuable food product, containing 40% protein and a large percentage of unsaturated fatty acids ranging from 17 to 23%. Pseudomonas savastanoi pv. glycinea (Psg) and Curtobacterium flaccumfaciens pv. flaccumfaciens (Cff) are harmful bacterial pathogens of soybean. The bacterial resistance of soybean pathogens to existing pesticides and environmental concerns requires new approaches to control bacterial diseases. Chitosan is a biodegradable, biocompatible and low-toxicity biopolymer with antimicrobial activity that is promising for use in agriculture. In this work, a chitosan hydrolysate and its nanoparticles with copper were obtained and characterized. The antimicrobial activity of the samples against Psg and Cff was studied using the agar diffusion method, and the minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) were determined. The samples of chitosan and copper-loaded chitosan nanoparticles (Cu²⁺ChiNPs) significantly inhibited bacterial growth and were not phytotoxic at the concentrations of the MIC and MBC values. The protective properties of chitosan hydrolysate and copper-loaded chitosan nanoparticles against soybean bacterial diseases were tested on plants in an artificial infection. It was demonstrated that the Cu²⁺ChiNPs were the most effective against Psg and Cff. Treatment of pre-infected leaves and seeds demonstrated that the biological efficiencies of (Cu²⁺ChiNPs) were 71% and 51% for Psg and Cff, respectively. Copper-loaded chitosan nanoparticles are promising as an alternative treatment for bacterial blight and bacterial tan spot and wilt in soybean.

Cellulose/inorganic nanoparticles-based nano-biocomposite for abatement of water and wastewater pollutants

Nanostructured materials offer a significant role in wastewater treatment with diminished capital and operational expense, low dose, and pollutant selectivity. Specifically, the nanocomposites of cellulose with inorganic nanoparticles (NPs) have drawn a prodigious interest because of the extraordinary cellulose properties, high specific surface area, and pollutant selectivity of NPs. Integrating inorganic NPs with cellulose biopolymers for wastewater treatment is a promising advantage for inorganic NPs, such as colloidal stability, agglomeration prevention, and easy isolation of magnetic material after use. This article presents a comprehensive overview of water treatment approaches following wastewater remediation by green and environmentally friendly cellulose/inorganic nanoparticles-based bio-nanocomposites. The functionalization of cellulose, functionalization mechanism, and engineered hybrid materials were thoroughly discussed. Moreover, we also highlighted the purification of wastewater through the composites of cellulose/inorganic nanoparticles via adsorption, photocatalytic and antibacterial approach.

Design and fabrication of chitosan cross-linked bismuth sulfide nanoparticles for sequestration of mercury in river water samples

The existence of heavy metals in ecological systems poses great threats to living organisms due to their toxicant and bio-accumulating properties. Mercury is a known toxicant with notable malignant impacts. It has long been known to cause toxic threats to the health of living organisms since the break out of Minamata disease. The turbulent expulsion of mercury-based pollutants from the industrial sector, requires a proper solution. Many attempts have been made to design a greener and more efficient route for a satisfactory removal of mercury. In the current study, bismuth sulfide nanoparticles (BiSNPs) have been synthesized via the co-precipitation method. The BiSNPs were supported with crosslinked chitosan to enhance their sorption capacity and avoid leaching. The average size of the BiSNPs was 42 nm based on SEM micrographs. The SEM analysis of the bismuth sulfide chitosan-crosslinked beads (BiS-CB) showed that the beads possessed a spherical and smooth morphology with a size of 1.02 mm. The FTIR analysis showed that the beads possessed the characteristics bands of imine groups of chitosan, bismuth, sulfur, and glycosidic linkages present in the molecules. The XRD analysis confirmed the phase crystallinity of the BiS-CB with an average crystallite size of 11 nm. The BiS-CB was employed for the sorption of mercury from water samples. The maximum sorption capacity of 65.51 mg/g was achieved at optimized conditions of pH 5, concentration 80 ppm, in 45 min at 30 °C. The mechanism studied for mercury removal showed that sorption followed the complexation mechanism according to the SHAB concept. In conclusion, the results showed that the BiS-CB sorbent exhibited an excellent sorption capacity to remove mercury.

Core-shell magnetic molecularly imprinted polymer for selective recognition and detection of sunset yellow in aqueous environment and real samples

Magnetic Molecularly imprinted polymers (MMIPs) have been recently recognized as an exceptional tool for monitoring and decontamination of environmental and biological samples of diverse nature. Based on the potential applications as sorbents and biomimetic sensors, herein, a core-shell magnetic-molecularly imprinted polymer (MMIP) was developed as a selective material for separation and sensing of sunset yellow (SY) dye in an aqueous environment and real samples. The MMIP was synthesized via precipitation polymerization using SY as a template, MAA as a functional monomer (chosen based on simulation studies), EGDMA as a cross-linking agent, and AIBN as an initiator. To elaborate the specificity of MMIP, a comparative agent, magnetic non-imprinted polymer (MNIP) was also synthesized. The XRD results showed that the MMIP showed both crystalline and amorphous structure attributed to the presence and polymeric and non-polymeric groups. The FTIR spectra confirmed synthesis of intermediate and final MMIP product. The SEM results showed spherical morphology and porous structure of the MMIP with an average particle size of 0.636 μm in diameter. The MMIP was first employed as a sorbent for the removal of SY from the aqueous environment. The binding experiments performed at optimized operating conditions (pH 2; time 30 min; sorbent dosage 3 mg; sorbate concentration 80 ppm) showed more selectivity when compared with MNIP. The data fitted best to Langmuir's sorption isotherm (Q_o 359.8 mg/g) and followed the pseudo-second-order kinetic model. The synthesized MMIP was also used as an electrochemical sensor for detection of SY dye in the aqueous environment, which exhibited a linear range of detection as (1.51 × 10^-6 - 1.5 × 10^-3 M). The limit of detection (LOD) and limit of quantification (LOQ) were found to be 0.00413 M and 0.0137 M, respectively. While the R² value was found to be 0.997 at optimized analytical conditions. These results suggested that the synthesized MMIP can be applied for the selective separation and quantification of SY dye in sample of diverse nature.

Hydrogel Beads of Amidoximated Starch and Chitosan as Efficient Sorbents for Inorganic and Organic Compounds

The synthesis of hydrogel beads involving natural polymers is, nowadays, a leading research area. Among natural polymers, starch and chitosan represent two biomolecules with proof of efficiency and low economic impact in various utilization fields. Therefore, herein, the features of hydrogel beads obtained from chitosan and three sorts of starch (potato, wheat and rise starches), grafted with acrylonitrile and then amidoximated, were deeply investigated for their use as sorbents for heavy metal ions and dyes. The hydrogel beads were prepared by ionotropic gelation/covalent cross-linking of chitosan and functionalized starches. The chemical structure of the hydrogel beads was analyzed by FT-IR spectroscopy; their morphology was revealed by optical and scanning electron microscopies, while the influence of the starch functionalization strategies on the crystallinity changes was evaluated by X-ray diffraction. Molecular dynamics simulations were used to reveal the influence of the grafting reactions and grafted structure on the starch conformation in solution and their interactions with chitosan. The sorption capacity of the hydrogel beads was tested in batch experiments, as a function of the beads’ features (synthesis protocol, starch sort) and simulated polluted water, which included heavy metal ions (Cu²⁺, Co²⁺, Ni²⁺ and Zn²⁺) and small organic molecules (Direct Blue 15 and Congo red).

Preparation and Characterization of Low-Cost Ceramic Membrane Coated with Chitosan: Application to the Ultrafine Filtration of Cr(VI)

In this work, low-cost ceramic membranes (CMs) were prepared from ultrafine starting powders such as kaolin, clay, and starch by a dry compaction method. The ceramic membranes were sintered at different temperatures and times and were characterized by XRD, XRF, TG-DTA, SEM-EDS, N₂-BET, water absorption, compressive strength, and pure water flux. The optimal membrane, sintered at 1000 °C for 3 h, possessed water absorption of 27.27%, a compressive strength of 31.05 MPa, and pure water flux of 20.74 L/h m². Furthermore, chitosan crosslinked with glutaraldehyde was coated on the surface of the ceramic membrane by the dip coating method, and the pore size of the chitosan-coated ceramic membrane (CCCM) was 16.24 nm. Eventually, the separation performance of this membrane was assessed for the removal of chromium(VI) from aqueous solution. The ultrafine filtration of Cr(VI) was studied in the pH range of 2-7. The maximum removal of Cr(VI) was observed to be 71.25% with a pH of 3. The prepared CCCM showed good membrane properties such as mechanical stability and ultrafine structure, which have important applications for the treatment of wastewater including such heavy metals.

Covalent and Non-covalent Functionalized Nanomaterials for Environmental Restoration

Nanotechnology has emerged as an extraordinary and rapidly developing discipline of science. It has remolded the fate of the whole world by providing diverse horizons in different fields. Nanomaterials are appealing because of their incredibly small size and large surface area. Apart from the naturally occurring nanomaterials, synthetic nanomaterials are being prepared on large scales with different sizes and properties. Such nanomaterials are being utilized as an innovative and green approach in multiple fields. To expand the applications and enhance the properties of the nanomaterials, their functionalization and engineering are being performed on a massive scale. The functionalization helps to add to the existing useful properties of the nanomaterials, hence broadening the scope of their utilization. A large class of covalent and non-covalent functionalized nanomaterials (FNMs) including carbons, metal oxides, quantum dots, and composites of these materials with other organic or inorganic materials are being synthesized and used for environmental remediation applications including wastewater treatment. This review summarizes recent advances in the synthesis, reporting techniques, and applications of FNMs in adsorptive and photocatalytic removal of pollutants from wastewater. Future prospects are also examined, along with suggestions for attaining massive benefits in the areas of FNMs.

Synthesis of hybrid biosorbent based on 1,2-cyclohexylenedinitrilotetraacetic acid modified crosslinked chitosan and organo-functionalized calcium alginate for adsorptive removal of Cu(II)

The present study is based on the synthesis of a novel hybrid biosorbent using 1,2-cyclohexylenedinitrilotetraacetic acid modified crosslinked chitosan and amino-thiocarbamate moiety functionalized sodium alginate (CDTA-CS/TSC-CA). The fabricated sorbent was employed to investigate the efficient recovery of Cu(II) from aqueous media. CDTA-CS/TSC-CA was characterized using Fourier Transform Infrared Spectroscopy (FTIR) and Scanning Electron Microscopy (SEM). Analysis confirmed the successful modification of both biopolymers and subsequent loading of Cu(II) ions. CDTA-CS/TSC-CA was casted in the form of hydrogel beads having different CDTA-CS to TSC-CA mass ratios i.e., 10.0-40.0% by mass. The hydrogel beads 4CDTA-CS/TSC-CA with CDTA-CS/TSC-CA mass ratio of 40.0% was found most effective for copper sorption. Equilibrium sorption results showed that initial concentration of copper, medium pH, contact time, sorbent dosage and temperature influenced the sorption capacity (q_e). Rate of sorption data was interpreted using different kinetic models and found best fitted with pseudo second order rate expression (R² ≈ 0.99), illustrating that the rate determining step includes the electron density transfer from sorbent coordination sites to central copper ions. Crank's RIDE equation and Elovich chemisorption model (ECM) revealed the presence of two sorption phases, initially rapid sorption followed by comparatively a slow uptake. Equilibrium sorption data was well depicted by Langmuir model and maximum monolayer adsorption capacity (q_m) was computed as 276.53 mg·g^-1 at 298 K. Standard Gibbs free energy change, ∆G° (-19.99, -20.18 and -20.36 kJ/ mol), standard enthalpy change, ∆H° (-8.95 kJmol) and standard entropy change, ∆S° (0.04 kJ/mol K^-1) values suggested that the adsorption process is spontaneous and exothermic. Hence, 4CDTA-CS/TSC-CA was found efficient biosorbent for copper removal from its dilute effluents.

Effects of Benzalkonium Chloride Contents on Structures, Properties, and Ultrafiltration Performances of Chitosan-Based Nanocomposite Membranes

The effects of benzalkonium chloride (BKC) contents on the structure, properties, and ultrafiltration performance of chitosan-based nanocomposite membranes containing poly(ethylene glycol) and multi-walled carbon nanotube (chitosan/BKC/PEG/CNT) were examined. The membranes were prepared by a mixing solution method and phase inversion before being characterized with microscopic techniques, tensile tests, thermogravimetric analysis, water contact angle, and porosity measurements. The performance of the nanocomposite membranes in regard to permeability (flux) and permselectivity (rejection) was examined. The results show that the incorporation of BKC produced nanocomposite membranes with smaller pore structures and improved physico-chemical properties, such as an increase in porosity and surface roughness (Ra = 45.15 to 145.35 nm and Rq = 53.69 to 167.44 nm), an enhancement in the elongation at break from 45 to 109%, and an enhancement in the mechanical strength from 31.2 to 45.8 MPa. In contrast, a decrease in the membrane hydrophilicity (water contact angle increased from 56.3 to 82.8°) and a decrease in the average substructure pore size from 32.64 to 10.08 nm were observed. The membrane rejection performances toward Bovine Serum Albumin (BSA) increased with the BKC composition in both dead-end and cross-flow filtration processes. The chitosan/BKC/PEG/CNT nanocomposite membranes have great potential in wastewater treatments for minimizing biofouling without reducing the water purification performance.

Preparation and applications of chitosan and cellulose composite materials

Chitosan is a natural fiber, chemically cellulose-like biopolymer, which is processed from chitin. Its use as a natural polymer is getting more attention because it is non-toxic, renewable, and biocompatible. However, its poor mechanical and thermal strength, particle size, and surface area restrict its industrial use. Consequently, to improve these properties, cellulose and/or inorganic nanoparticles have been used. This review discusses the recent progress of chitosan and cellulose composite materials, their preparation, and their applications in different industrial sectors. It also discusses the modification of chitosan and cellulose composite materials to allow their use on a large scale. Finally, the recent development of chitosan composite materials for drug delivery, food packaging, protective coatings, and wastewater treatment are discussed. The challenges and perspectives for future research are also considered. This review suggests that chitosan and cellulose nano-composite are promising, low-cost products for environmental remediation involving a simple production process.

Microbial recovery of critical metals from secondary sources

The continuous development of technologies involving critical metals, both in Europe and over the world, and geopolitical challenges in areas rich in critical metal sources, imposed increased research efforts to recover them from secondary sources, by eco-efficient processes. Yet, microbes-metal interactions are not sufficiently exploited to recover metals from secondary sources, although they are already used in ore extraction. This review examines and compare strategies and processes involving microorganisms for critical metals recovery, since conventional physico-chemical methods are energy-intensive and often polluting. Two groups of microbial assisted recovery processes are discussed: metal mobilization from metal bearing waste, and selective metal separation from leaching solutions by immobilization on microbial biomass. Because most of the identified microbial technologies are developed on laboratory scale, the increase of biorecovery efficiency is compulsory for enhancing scaling-up potential. Future developments focused on novel microorganisms and high-performance strategies for critical metal recovery by microbial processes are considered.

Development of poly(vinyl alcohol)/chitosan/aloe vera gel electrospun composite nanofibers as a novel sorbent for thin-film micro-extraction of pesticides in water and food samples followed by HPLC-UV analysis

Schematic presentation of applying PVA/CA/CS/AV composite nanofibers as the extraction phase in thin-film micro-extraction (TFME) of six pesticide compounds prior to HPLC-UV analysis.

Sustainable remediation of hazardous environmental pollutants using biochar-based nanohybrid materials

Biochar is a well-known carbon material with diversified functionalities and excellent physicochemical characteristics with high wastewater treatment potential. This review aims to summarize recent advancements in the development of biochar and biochar-based nanohybrid materials as a potential tool for the removal of harmful organic compounds such as synthetic dyes/effluents. The formation of biochar using pyrolysis of renewable feedstocks and their applications in various industries are explained hereafter. The characteristics and construction of biochar-based hybrid materials are explained in detail. Diversity of feedstocks, including municipal wastes, industrial byproducts, agricultural, and forestry residues, endows different biochar types with a wide structural variety. The production of cost-effective biochar drives the interest in manipulating biochars and induces desire functionality using nanoscale reinforcements. Various types of biochars, such as magnetic biochar, layered nanomaterial coated biochar, nanometallic oxide composites, chemically and physically functionalized biochar, have been produced. With the aid of nanomaterial, hybrid biochar exhibits a high potential to remove toxic contaminants. Depending upon biochar type, dyes/effluents can be removed via different mechanisms, including the Fenton process, photocatalytic degradation, π-π interaction, electrostatic interaction, and physical adsorption. In conclusion, desired physicochemical features, and tunable surface properties of biochar present high potential material in removing organic dyes and other effluents. The blended biochar with different materials/nanomaterials endows broader development and multi-functional opportunities for treating dyes/effluents.

Development and characterization of regenerable chitosan-coated nickel selenide nano-photocatalytic system for decontamination of toxic azo dyes

In this investigation, chitosan-coated nickel selenide nano-photocatalyst (CS-NiSe) was successfully prepared through the chemical reduction method. FTIR spectroscopy confirmed the synthesis of CS-NiSe nano-photocatalyst. Further, XRD analysis exhibited a monoclinic crystalline phase of photocatalyst with a crystallite size of 32 nm based on Scherer's equation. The SEM micrographs showed that the photocatalyst has an average particle size of 60 nm. The bandgap of CS-NiSe was (2.85 eV) in the visible region of the spectrum. Due to this reason, the CS-NiSe was applied under solar light illumination for the photocatalytic activity of Erythrosine and Allura red dyes. The CS-NiSe presented the highest degradation efficiency of 99.53% for Erythrosine dye in optimized experimental conditions of 100 min at 30 °C, 30 ppm concentration, pH 5.0, and 0.14 g catalyst dose. For Allura red dye, a high degradation of 96.12% was attained in 120 min at pH 4.0, 100 ppm initial dye concentration, 35 °C temperature, and 0.1 g catalyst dose. The CS-NiSe showed excellent degradation efficiency and reduced to (95% for Erythrosine and 91% for Allura red dye) after five consecutive batches. Moreover, the statistical and neural network modelling analysis showed the significant influence of all studied variables on dyes degradation performance. The results demonstrated that CS-NiSe exhibited excellent photocatalytic performances for Erythrosine and Allura red dyes and could be a better photocatalyst for removing these dyes from industrial effluents.

Gamma radiation-induced grafting of poly(2-aminoethyl methacrylate) onto chitosan: A comprehensive study of a polyurethane scaffold intended for skin tissue engineering

A novel brush-like poly(2-aminoethyl methacrylate) (PAEMA) was grafted onto chitosan (CS) through gamma radiation-induced polymerization. The copolymer (CS-g-PAEMA) was used to prepare a sodium acetate leached poly(urethane-urea) scaffold. The above derivatives were developed, synthesized, and characterized to meet the specific characteristics of biomaterials. The results revealed that this method is an easy and successful route for grafting PAEMA onto CS. The feasibility of preparing a CS-g-PAEMA polyurethane foam was confirmed by mechanical, morphometric, spectroscopic, and cytotoxic studies. The scaffold showed high biocompatibility both in vitro and in vivo. The first experiment proved that CS-based polyurethane efficiently allows the dynamic culturing of human fibroblast cells. Additionally, an in vivo study in a murine model indicated a complete integration of the scaffold to surrounding subcutaneous tissue as supported by the histological and histochemical assessments. The aforementioned results support the use of CS-g-PAEMA poly(saccharide-urethane) as a model of in vitro-engineered skin.

Toughened chitosan-based composite membranes with antibiofouling and antibacterial properties via incorporation of benzalkonium chloride

Biofouling due to biofilm formation is a major problem in ultrafiltration membrane applications. In this work, a potential approach to solve this issue has been developed by functionalization of chitosan-based membranes with benzalkonium chloride (BKC). The chitosan composite membranes consisting of poly(ethylene glycol) (PEG), multiwalled carbon nanotubes (MWCNT), and BKC were synthesized by mixing the membrane precursors and the antibacterial solution, and casting via an inversed phase technique. The effects of the BKC content on the morphology and performance of the membranes are investigated by varying the BKC feed compositions. The composite membranes demonstrate better antibacterial efficacy against Staphylococcus aureus than Escherichia coli. The permeability and selectivity performances of the composites as filter membranes are examined by employing a dead-end filtration system. Interestingly, enhanced toughness of the membranes is observed as a function of the BKC content. Mechanisms of the structural formation are investigated. The results from SEM, XRD, and FTIR spectroscopy revealed that MWCNT/BKC are located as nanoclusters with π–π stacking interactions, and are covered by PEG chains. The shape of the dispersed domains is spherical at low BKC contents, but becomes elongated at high BKC contents. These act as soft domains with an anisotropic shape with toughening of the brittle chitosan matrix, leading to enhanced durability of the membranes, especially in ultrafiltration applications. The composite membranes also demonstrate improved rejection in dead-end ultrafiltration systems due to high porosity, high hydrophilicity, and the positive charges of the membrane surface.

Chitosan/PEG/MWCNT/BKC membranes exhibit enhanced antibiofouling properties against S. aureus and E. coli. MWCNT/BKC are located as dispersed nano-clusters with π–π stacking interactions in the chitosan matrix, and are coved by PEG chains.

Chitosan-capped ternary metal selenide nanocatalysts for efficient degradation of Congo red dye in sunlight irradiation

Wastewater emerging from the industries containing organic pollutants is a severe threat to humans' health and aquatic life. Therefore, the degradation of highly poisonous organic dye pollutants is necessary to ensure public health and environmental protection. To tackle this problem, visible-light-driven ternary metal selenide nanocomposites were synthesized successfully by the solvothermal method and supported by chitosan microspheres (FeNiSe-CHM). The prepared nanoparticles were capped in chitosan microspheres to avoid leaching and facilitate easy recovery of the catalyst. FTIR spectrum confirmed the synthesis of nanocomposite and nanocomposite-chitosan microspheres (FeNiSe-CHM). Based on the SEM images, the nanomaterial and FeNiSe-CHM has an average particle size of 64 nm and 874 μm, respectively. The presence of iron, nickel and selenium elements in the EDX spectrum revealed the synthesis of FeNiSe-NPs. XRD analysis determined the crystallite structure of nanocomposites as 14.2 nm. The photocatalyst has a crystalline structure and narrow bandgap of 2.09 eV. Moreover, the as-synthesized FeNiSe-CHM were employed for the photodegradation of carcinogenic and mutagenic Congo red dye. The catalyst microspheres showed efficient photocatalytic degradation efficiency of up to 99% for Congo red dye under the optimized conditions of 140 min, pH 6.0, dye concentration 60 ppm and catalyst dose of 0.2 g in the presence of sunlight irradiation following the second-order kinetics. After five consecutive cycles, it showed a slight loss in the degradation efficiency. In conclusion, the results demonstrate a high potential of chitosan-based ternary metal selenide nanocomposites for abatement of dye pollutants from the industrial wastewater.

Selenide-chitosan as High-performance Nanophotocatalyst for Accelerated Degradation of Pollutants

Water pollution is one of the major global challenges today. Water bodies are contaminated by the heavy release of waste effluents of textile industries, which includes intensively colored dye pollutants. Herein, a ternary nanocomposite of bismuth copper selenide with small particle size and ternary metal selenide (TMS)-chitosan microspheres (TMS-CM) of the spherical porous surface were successfully synthesized. SEM, XRD, EDX, FTIR, and UV/Vis spectrophotometry analysis revealed the structural and morphological characteristics of the newly synthesized nanocomposites. SEM imaging showed the average diameter of TMS nanoparticle to be 33 nm. The crystal size was calculated as 6.33 nm and crystalline structure as orthorhombic using XRD findings. EDX confirmed the presence of Bi, Cu, and Se in the ternary nanocomposite. The bandgap of 1.8 eV was calculated from Tauc's plot for the TMS nanocomposite. SEM confirmed the successful synthesis of spherical TMS-CM microspheres of porous surface morphology with an average size of 885.6 μm. The presence of chitosan microspheres in the synthesis of TMS nanocomposite was identified by FTIR spectral analysis. Furthermore, highly efficient photocatalytic degradation (up to 95.4%) of ARS was achieved within 180 min at pH 4.0 using 0.5 g of TMS-CM in sunlight. The first-order kinetic model fitted well to the photocatalytic decontamination of ARS using TMS-CM with a rate constant of 6.1x10^-2  min^-1 . The TMS-CM gave attractive results and high efficiency in photocatalytic degradation of ARS dye after reusing and regeneration of up to seven successive cycles. The newly synthesized nanophotocatalyst could be efficiently used for the decontamination of dye polluted water from textile industries.