Selective and sensitive detection of nitrite based on NO sensing on a polymer-coated rotating disc electrode

Highly Sensitive Graphene-Based Electrochemical Sensor for Nitrite Assay in Waters

The importance of nitrite ions has long been recognized due to their extensive use in environmental chemistry and public health. The growing use of nitrogen fertilizers and additives containing nitrite in processed food items has increased exposure and, as a result, generated concerns about potential harmful health consequences. This work presents the development of an electrochemical sensor based on graphene/glassy carbon electrode (EGr/GC) with applicability in trace level detection of nitrite in water samples. According to the structural characterization of the exfoliated material, it appears as a mixture of graphene oxide (GO; 21.53%), few-layers graphene (FLG; 73.25%) and multi-layers graphene (MLG; 5.22%) and exhibits remarkable enhanced sensing response towards nitrite compared to the bare electrode (three orders of magnitude higher). The EGr/GC sensor demonstrated a linear range between 3 × 10^-7 and 10^-3 M for square wave voltammetry (SWV) and between 3 × 10^-7 and 4 × 10^-4 M for amperometry (AMP), with a low limit of detection LOD (9.9 × 10^-8 M). Excellent operational stability, repeatability and interference-capability were displayed by the modified electrode. Furthermore, the practical applicability of the sensor was tested in commercially available waters with excellent results.

Electrochemical Sensors Based on the Electropolymerized Natural Phenolic Antioxidants and Their Analytical Application

The design and fabrication of novel electrochemical sensors with high analytical and operational characteristics are one of the sustainable trends in modern analytical chemistry. Polymeric film formation by the electropolymerization of suitable monomers is one of the methods of sensors fabrication. Among a wide range of the substances able to polymerize, the phenolic ones are of theoretical and practical interest. The attention is focused on the sensors based on the electropolymerized natural phenolic antioxidants and their analytical application. The typical electropolymerization reaction schemes are discussed. Phenol electropolymerization leads to insulating coverage formation. Therefore, a combination of electropolymerized natural phenolic antioxidants and carbon nanomaterials as modifiers is of special interest. Carbon nanomaterials provide conductivity and a high working surface area of the electrode, while the polymeric film properties affect the selectivity and sensitivity of the sensor response for the target analyte or the group of structurally related compounds. The possibility of guided changes in the electrochemical response for the improvement of target compounds' analytical characteristics has appeared. The analytical capabilities of sensors based on electropolymerized natural phenolic antioxidants and their future development in this field are discussed.

New application for TiO2 P25 photocatalyst: A case study of photoelectrochemical sensing of nitrite ions

Developing photoelectrochemical (PEC) sensors based on photocatalytic materials has recently attracted great interest as an emerging technology for environmental monitoring. TiO₂ P25 is a well-known highly active photocatalyst, cheap, and produced commercially on a large scale. In the current work, a practical and durable TiO₂-based PEC sensor has been fabricated by immobilizing TiO₂ P25 nanoparticles at disposable screen-printed carbon substrates using drop-casting method. The fabricated PEC sensor has been applied for the anodic-detection and determination of nitrite (NO₂^-) ions under UV(A) light (LED, 365 nm) using chronoamperometry (CA) and differential pulse voltammetry (DPV). Linear calibration curves were obtained between the photocurrent responses and the concentrations of NO₂^- ions in the ranges of 0.1-5.0 and 0.5-10 mg L^-1 for CA and DPV, respectively. Surprisingly, the detection limits (sensitivities) of the fabricated sensor towards NO₂^- ions under light were enhanced by a factor of 4.75 (4.1) and 8.3 (37.4) for CA and DPV, respectively, in comparsion with those measured in the dark. It is found that the photo-excitation of TiO₂ facilitates the photooxidation of NO₂^- ions via the photo-generated holes whereas the photogenerated electrons contribute to the enhanced photocurrent and consequently the enhanced detection limit and sensitivity. The fabricated TiO₂-based PEC sensor exhibits a good stability, durability, and satisfying selectivity for NO₂^- ions determination. These results indicate that the TiO₂-based PEC sensor fabricated by utilizing cheap and commercially available components has great potential for being transferred from lab-to-factory.

A green carbon dots-based fluorescent sensor for selective and visual detection of nitrite triggered by the nitrite–thiol reaction

Selective and visual detection of nitrite is realized through the inner-filter effect triggered by the nitrite–thiol reaction based on green carbon dots.

A new electrochemical sensor for highly sensitive and selective detection of nitrite in food samples based on sonochemical synthesized Calcium Ferrite (CaFe2O4) clusters modified screen printed carbon electrode

Herein, we report a novel, disposable electrochemical sensor for the detection of nitrite ions in food samples based on the sonochemical synthesized orthorhombic CaFe₂O₄ (CFO) clusters modified screen printed electrode. As synthesized CFO clusters were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transformer infrared spectroscopy (FT-IR), Thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS), electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and amperometry (i-t). Under optimal condition, the CFO modified electrode displayed a rapid current response to nitrite, a linear response range from 0.016 to 1921 µM associated with a low detection limit 6.6 nM. The suggested sensor also showed the excellent sensitivity of 3.712 μA μM^-1 cm^-2. Furthermore, a good reproducibility, long-term stability and excellent selectivity were also attained on the proposed sensor. In addition, the practical applicability of the sensor was investigated via meat samples, tap water and drinking water, and showed desirable recovery rate, representing its possibilities for practical application.

Polypyrrole with a functionalized multi-walled carbon nanotube hybrid nanocomposite: a new and efficient nitrite sensor

This study mainly focuses on the electrochemical-assisted synthesis of conducting polymers such as polypyrrole (PPy) with sodium dodecyl sulfate (SDS) as a surfactant and supported with functionalized multi-walled carbon nanotubes (f-MWCNTs).

Preparation of hexagonal BN whiskers synthesized at low temperature and their application in fabricating an electrochemical nitrite sensor

Hexagonal boron nitride (h-BN) whiskers were synthesized via the polymeric precursor method using boric acid (H₃BO₃) and melamine (C₃H₆N₆) as raw materials at 1073–1273 K in flowing nitrogen/hydrogen (5% hydrogen).

Electrochemical detection of nitrite based on glassy carbon electrode modified with gold–polyaniline–graphene nanocomposites

This study reports possible interferences for the detection of NO₂⁻ on a Au–G–PANI/GCE.