Glassy carbon electrodes modified with CNT dispersed in chitosan: Analytical applications for sensing DNA–methylene blue interaction

Application of silver solid amalgam electrodes in electrochemical detection of DNA damage

In this study, a mercury meniscus-modified silver solid amalgam electrode was used for the first time for the detection of UV-induced DNA damage. The integrity of the double-stranded DNA (dsDNA) layer was detected indirectly using the evaluation of the methylene blue reduction within its accumulation into dsDNA after the UV irradiation of the biosensor surface with two different wavelengths (254 nm and 365 nm), monitored by differential pulse voltammetry. Moreover, a simple electrochemical characterization of the biosensor surface was performed using cyclic voltammetry of the redox indicator hexaammineruthenium chloride (RuHex) present in the solution. Electrochemical impedance spectroscopy (EIS) was used in both cases for the verification of results. Individual electrochemical signals depend on the time of biosensor exposure to UV irradiation as well as on the selected wavelengths and are different for both used types of dsDNA (salmon sperm and calf thymus). The highest degradation degree up to 60% was observed using sensitive EIS of methylene blue after 10 min irradiation of the biosensor at 254 nm. The use of RuHex seems to be less sensitive for the detection of dsDNA structural changes, when the degradation degree up to 40% was observed, using EIS at the same conditions.

Novel DNA Biosensor for Direct Determination of Carrageenan

A novel disposable electrochemical biosensor based on immobilized calf thymus double-stranded DNA (dsDNA) on the carbon-based screen-printed electrode (SPE) is developed for rapid biorecognition of carrageenan by using methylene blue (MB) redox indicator. The biosensor protocol for the detection of carrageenan is based on the concept of competitive binding of positively charged MB to the negatively charged dsDNA and carrageenan. The decrement in the MB cathodic peak current (i_pc) signal as a result of the released MB from the immobilized dsDNA, and attracted to the carrageenan can be monitored via differential pulse voltammetry (DPV). The biosensor showed high sensitivity and selectivity to carrageenan at low concentration without interference from other polyanions such as alginate, gum arabic and starch. Calibration of the biosensor with carrageenan exhibited an excellent linear dependence from 1–10 mg L⁻¹ (R² = 0.98) with a detection limit of 0.08 mg L⁻¹. The DNA-based carrageenan biosensor showed satisfactory reproducibility with 5.6–6.9% (n = 3) relative standard deviations (RSD), and possessing several advantages such as simplicity, fast and direct application to real sample analysis without any prior extensive sample treatments, particularly for seaweeds and food analyses.

Methylene blue covalently attached to single stranded DNA as electroactive label for potential bioassays

Methylene blue is an electroactive molecule that has been employed for the detection of the DNA hybridization event in electrochemical sensors. However, its use as a covalent label is very scarce and in most of the cases, non-covalent interactions (hydrophobic, electrostatic) are employed. Although it has advantages as simplicity and fewer number of procedure steps, the covalent attachment is less exploited in the development of these sensors. In this article, the electrochemical behavior of methylene blue attached to different DNA-strands is studied. Several lengths (15- and 30-mer) and different degree of DNA modification (MB-DNA, MB-DNA-MB and MB-DNA-SH) have been studied. The highest signals were obtained for longer strands with two MB molecules. In all the cases the signal is enhanced by CNT-nanostructuration of the electrode. Adsorption on these modified screen-printed electrodes allowed the amplification by employing an accumulation time. In this way, a sensitivity of -0.2864 μA μM-1 and a limit of detection of 800 nM for a 120 s accumulation time were obtained.

A simple label-free electrochemical aptasensor for dopamine detection

A simple and label-free electrochemical biosensor based on a dopamine DNA aptamer was developed for the sensitive and selective detection of dopamine.

Simultaneous determination of ascorbic acid and rutin in pharmaceutical preparations with electrochemical method based on multi-walled carbon nanotubes-chitosan composite film modified electrode

In this paper, the simultaneous voltammetric determination of ascorbic acid (AA) and rutin (Ru) has been achieved at an acetylene black paste electrode modified with multi-walled carbon nanotubes-chitosan composite film (denoted as MWCNTs-CHIT/ABPE). Compared with bare electrode, the peak currents of AA and Ru at MWCNTs-CHIT/ABPE increased greatly and the anodic peak potential difference (ΔE(pa)) between AA and Ru are up to 342mV, which is undoubtedly attributed to the unique characteristics of AB and MWCNTs such as excellent electric conductivity, high surface area and strong adsorptive abilities, resulting in higher accumulation efficiency to AA and Ru. The influences of some experimental conditions on the oxidation of AA and Ru were tested and the calibration plot was examined. Under the optimized condition, a good linearity was obtained in the concentration range of 1μM-0.4mM for AA in the presence of 10μM Ru and 20nM-10μM for Ru in the presence of 1mM AA. The detection limits (S/N=3) of AA and Ru are 0.8μM and 10nM, respectively. The proposed method was successfully applied to the simultaneous determination of AA and Ru in pharmaceutical samples with reliable recovery.

Carbon nanotube-chitosan modified disposable pencil graphite electrode for vitamin B12 analysis

A single walled carbon nanotube-chitosan (SWCNT-chitosan) modified disposable pencil graphite electrode (PGE) was used in this study for the electrochemical detection of Vitamin B(12). Electrochemical behaviors of SWCNT-chitosan PGE and chitosan modified PGE were compared by using cyclic voltammetry (CV), square-wave voltammetry (SWV) and electrochemical impedance spectroscopy (EIS) techniques. SWCNT-chitosan modified electrode was also used for the quantification of Vitamin B(12) in pharmaceutical products. The results show that this electrode system is suitable for sensitive Vitamin B(12) analysis giving good recovery results. The surface morphologies of the SWCNT-chitosan PGE, chitosan modified PGE and unmodified PGE were characterized by using scanning electron microscopy (SEM).

Chitosan: an integrative biomaterial for lab-on-a-chip devices

Chitosan is a naturally derived polymer with applications in a variety of industrial and biomedical fields. Recently, it has emerged as a promising material for biological functionalization of microelectromechanical systems (bioMEMS). Due to its unique chemical properties and film forming ability, chitosan serves as a matrix for the assembly of biomolecules, cells, nanoparticles, and other substances. The addition of these components to bioMEMS devices enables them to perform functions such as specific biorecognition, enzymatic catalysis, and controlled drug release. The chitosan film can be integrated in the device by several methods compatible with standard microfabrication technology, including solution casting, spin casting, electrodeposition, and nanoimprinting. This article surveys the usage of chitosan in bioMEMS to date. We discuss the common methods for fabrication, modification, and characterization of chitosan films, and we review a number of demonstrated chitosan-based microdevices. We also highlight the advantages of chitosan over some other functionalization materials for micro-scale devices.