Determination of ractopamine in pork by using electrochemiluminescence inhibition method combined with molecularly imprinted stir bar sorptive extraction

Mesoporous silica-mediated controllable electrochemiluminescence quenching for immunosensor with simplicity, sensitivity and tunable detection range

Straightforward and accurate measurement of medical biomarkers is of essential importance in clinical diagnostics and treatments. However, the major challenge is the diversity in dynamic range of different biomarkers ranging from pg mL^-1 to μg mL^-1 in various body fluids and tissues among patients. Here, we develop a mesoporous silica (MS)-mediated controllable electrochemiluminescence (ECL) quenching of immunosensor that allows accurate immunoassays with simplicity, sensitivity and tunable sensing range. MS is employed to enhance the sensitivity and tune ECL quenching to broaden the detection range just by altering luminophore (Ru(bpy)₃²⁺) and coreactant (DBAE) concentration without additional modifications. The immunoassay is followed: homogeneous sandwich immunoreaction, magnetic separation, and ECL quenching detection. As a proof-of-concept, simple and sensitive detection of IgG is achieved ranging from pg mL^-1 to μg mL^-1, and applications of the strategy are extended by the combination of ECL immunosensor with commercial ELISA kit. This study will not only be expected to serve as a new avenue for the assay of physiological and clinical implications of immunological biomarkers, but also benefit a wide range of applications that require a tunable detection range and ultrahigh sensitivity.

A highly-enhanced electrochemiluminescence luminophore generated by a metal-organic framework-linked perylene derivative and its application for ractopamine assay

In this study, a sensitive and effective monitoring method for ractopamine (RAC) was developed based on a sensitive electrochemiluminescence (ECL) aptasensor. Here, we employed a perylene derivative (PTC-PEI) with a Cu-based metal-organic framework (HKUST-1), which could accelerate the electron-transfer (ET) rate and strengthen interactions by the amido bond, resulting in enhanced ECL sensitivity and stability. Astonishingly, compared with the response of PTC-PEI and complex, the ECL signal of the MOF-based ECL material was noticeably raised by 6 times higher than that of PTC-PEI. HKUST-1 exhibited an excellent catalytic effect towards the electrochemical reduction process of S₂O₈^2-, thus allowing more sulfate radical anions (SO₄˙^-) to be generated. The strong ECL intensity of HKUST-1/PTC-PEI not only stemmed from the fixation of PTC-PEI that utilized its excellent film-forming abilities but also originated from the high porosity of HKUST-1 that carried more luminophores able to be excited. Satisfyingly, in the presence of the target molecule RAC, we observed an obvious quenching effect of signal, which could be attributed to aptamer recognition resulting in RAC being specifically captured on the electrode. Under optimal conditions, the developed sensor for the RAC assay displayed a desired linear range of 1.0 × 10^-12-1.0 × 10^-6 M and a low detection limit of 6.17 × 10^-13 M (S/N = 3). This ECL sensor showed high sensitivity, good stability and excellent selectivity. More importantly, the proposed aptasensor exhibited excellent determination towards RAC detection and potential practical utility for real samples.

Fabrication of an electrochemical biodevice for ractopamine detection under a strategy of a double recognition of the aptamer/molecular imprinting polymer

The importance of RAC tracking in human biofluids has boosted many demands for designing an ultrasensitive tool to determine the trace value of the RAC from clinical, judicial, and forensic centers. In this study, an electrochemical biodevice has developed for the highly selective detection of this illegal feed additive under a double recognition strategy of the aptamer (Apt) and molecular imprinting polymer (MIP) on a glassy carbon electrode (GCE). The sensing relies on this fact that both the MIP and Apt act synergistically to trap the RAC molecules. The sensing surface fabrication steps have been monitored by some electrochemical techniques such as electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV(. The charge transfer resistance (R_ct) value of the redox probe as a representative of the biodevice response has increased linearly with the RAC concentration increasing in a dynamic range of 1 fM to 1.90 µM. The detection limit (LOD) value has been estimated to be 330 aM, lower than all of the reported methods in the RAC sensing. Furthermore, the practical feasibility of biodevice has been evaluated in some human blood serum and urine samples. This strategy offers some useful advantages in reliable detection of the RAC, which may help in the routine analysis, as mandated by regulatory agencies.

Cross-linked chitosan/thiolated graphene quantum dots as a biocompatible polysaccharide towards aptamer immobilization

Chitosan has a number of commercial and possible biomedical uses. Chitosan as a polysaccharide is a bioactive polymer with a variety of applications due to its functional properties such as antibacterial activity, non-toxicity, ease of modification, and biodegradability. In this work, cross-linked chitosan/thiolated graphene quantum dot as a biocompatible polysaccharide was modified by gold nanoparticle and used for immobilization of ractopamine (RAC) aptamer. A highly specific DNA-aptamer (5'-SH-AAAAAGTGCGGGC-3'), selected to RAC was immobilized onto thiolated graphene quantum dots (GQDs)-chitosan (CS) nanocomposite modified by gold nanostructures (Au NSs) and used for quantification of RAC. Different shapes of gold nanostructures with various sizes from zero-dimensional nanoparticles to spherical structures were prepared by one-step template-assistant green electrodeposition method. Fully electrochemical methodology was used to prepare a new transducer on a glassy carbon surface which provided a high surface area to immobilize a high amount of the aptamer. Therefore, a label free electrochemical (EC) apta-assay for ultrasensitive detection of RAC was developed. A special immobilization media consisting of Au NSs/GQDs-CS/Cysteamine (CysA) was utilized to improve conductivity and performance of the biosensor. The RAC aptamer was attached on the Au NSs of the composite membrane via AuS bond. The fabrication process of the EC aptamer based assay was characterized by some electrochemical techniques. The peak currents obtained by differential pulse voltammetry decreased linearly with the increasing of RAC concentrations and the apta-assay responds approximately over a wide dynamic range of RAC concentration from 0.0044 fM to 19.55 μM. The low limit of quantification was 0.0044 fM.

Electrochemical luminescence determination of hyperin using a sol-gel@graphene luminescent composite film modified electrode for solid phase microextraction

In this paper, a novel electrochemiluminescence (ECL) sensor of sol-gel@graphene luminescent composite film modified electrode for hyperin determination was prepared using graphene (G) as solid-phase microextraction (SPME) material, based on selective preconcentration of target onto an electrode and followed by luminol ECL detection. Hyperin was firstly extracted from aqueous solution through the modified GCE. Hydrogel, electrogenerated chemiluminescence reagents, pH of working solution, extraction time and temperature and scan rate were discussed. Under the optimum conditions, the change of ECL intensity was in proportion to the concentration of hyperin in the range of 0.02-0.24μg/mL with a detection limit of 0.01μg/mL. This method showed good performance in stability, reproducibility and precision for the determination of hyperin.

A Novel Electrochemiluminescence Sensor for Sensitive Determination of Carbaryl Based on Solid Phase Microextraction at NH2–Graphene–Nafion Modified Electrode

Sensitive electrochemiluminescence (ECL) detection and solid phase microextraction (SPME) using a NH2–graphene–Nafion modified glassy carbon electrode was developed for carbaryl. The NH2–graphene was synthesised and characterised by Fourier transform infrared spectroscopy, scanning electron microscopy, and X-ray diffraction. The main parameters that affect the extraction efficiencies, such as the buffer and sample pH, and extraction time were investigated and optimised. The introduction of NH2–graphene into Nafion improves the conductivity of the film because of its electrical conductivity. The electrode enables the determination of carbaryl in the range from 5 × 10–4 to 10 μg mL–1, and the limit of detection was 2 × 10–4 μg mL–1 at a signal-to-noise ratio of 3. The ECL intensity retained 97 % of its initial response current after storage for 10 days, indicating a good storage stability of the sensor. The relative standard deviations (RSDs) of intra-assay and inter-assay were found to be 3.5 and 5.3 %, respectively, indicating an acceptable reproducibility. Furthermore, the ECL sensor was successfully applied to the selective and sensitive quantitative determination of carbaryl in river samples, the recoveries of carbaryl ranged from 99.0 to 108.0 %, and the RSDs were less than 5.0 %, which shows good reproducibility and high precision of analysis.

A molecularly imprinted sensor based on an electrochemiluminescent membrane for ultratrace doxycycline determination

A new electrochemical luminescence sensor was developed based on a molecularly imprinted membrane prepared by electropolymerization of pyrogallol doped with alizarin red. The ECL signal was produced by the oxidation of the polypyrogallol polymer, which was then reacted with alizarin red, and enhanced by doxycycline molecules due to energy transfer.

Stir bar sorptive extraction: recent applications, limitations and future trends

Stir bar sorptive extraction (SBSE) has generated growing interest due to its high effectiveness for the extraction of non-polar and medium-polarity compounds from liquid samples or liquid extracts. In particular, in recent years, a large amount of new analytical applications of SBSE has been proposed for the extraction of natural compounds, pollutants and other organic compounds in foods, biological samples, environmental matrices and pharmaceutical products. The present review summarizes and discusses the theory behind SBSE and the most recent developments concerning its effectiveness. In addition, the main results of recent analytical approaches and their applications, published in the last three years, are described. The advantages, limitations and disadvantages of SBSE are described and an overview of future trends and novel extraction sorbents and supports is given.

Flow-injection chemiluminescence method to detect a β2 adrenergic agonist

A new method for the detection of β2 adrenergic agonists was developed based on the chemiluminescence (CL) reaction of β2 adrenergic agonist with potassium ferricyanide-luminol CL. The effect of β2 adrenergic agonists including isoprenaline hydrochloride, salbutamol sulfate, terbutaline sulfate and ractopamine on the CL intensity of potassium ferricyanide-luminol was discovered. Detection of the β2 adrenergic agonist was carried out in a flow system. Using uniform design experimentation, the influence factors of CL were optimized. The optimal experimental conditions were 1 mmol/L of potassium ferricyanide, 10 µmol/L of luminol, 1.2 mmol/L of sodium hydroxide, a flow speed of 2.6 mL/min and a distance of 1.2 cm from 'Y2 ' to the flow cell. The linear ranges and limit of detection were 10-100 and 5 ng/mL for isoprenaline hydrochloride, 20-100 and 5 ng/mL for salbutamol sulfate, 8-200 and 1 ng/mL for terbutaline sulfate, 20-100 and 4 ng/mL for ractopamine, respectively. The proposed method allowed 200 injections/h with excellent repeatability and precision. It was successfully applied to the determination of three β2 adrenergic agonists in commercial pharmaceutical formulations with recoveries in the range of 96.8-98.5%. The possible CL reaction mechanism of potassium ferricyanide-luminol-β2 adrenergic agonist was discussed from the UV/vis spectra.