Experimental corroboration of the theory of chronoamperometry at high roughness electrode for reversible charge transfer

In Situ Electrochemical Impedance Spectroscopic Method for Determination of Surface Roughness and Morphological Convexity

A novel in situ electrochemical impedance spectroscopy (EIS) method is developed for the determination of RMS roughness (h), electroactive roughness factor (R_c^*), and morphological convexity (H̅*) of the electrode surface. Our method uses the angular frequency of maximum phase (ω_M) in anomalous Warburg impedance to extract in situ RMS roughness (h). The compact electric double layer (C-EDL) formation frequency (ω_H) is used to extract the electroactive roughness factor and morphological convexity. The theory unravels the inverse square root dependence of h on ω_M through an elegant equation, h=D/ωM, where D is the diffusion coefficient of electroactive species. Similarly, the equation for the electroactive roughness factor is R_c^* = ω_H⁰/ω_H and ω_H⁰ is the smooth electrode C-EDL formation frequency. These equations are validated for the nanoparticles deposited and mechanically roughened Pt electrodes. Finally, this in situ method is applicable for both low and high roughness electrodes which transcend the limitations of contemporary methods.

Surface Modification Effect and Electrochemical Performance of LiOH-High Surface Activated Carbon as a Cathode Material in EDLC

This study aimed to improve the performance of the activated carbon-based cathode by increasing the Li content and to analyze the effect of the combination of carbon and oxidizing agent. The crystal structure and chemical structure phase of Li-high surface area activated carbon material (Li-HSAC) was analyzed by X-ray diffraction (XRD) and Raman spectroscopy, the surface state and quantitative element by scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDX) and the surface properties with pore-size distribution by Brunauer–Emmett–Teller (BET), Barrett–Joyner–Halenda (BJH) and t-plot methods. The specific surface area of the Li-YP80F is 1063.2 m²/g, micropore volume value is 0.511 cm³/g and mesopore volume is 0.143 cm³/g, and these all values are higher than other LiOH-treated carbon. The surface functional group was analyzed by a Boehm titration, and the higher number of acidic groups compared to the target facilitated the improved electrolyte permeability, reduced the interface resistance and increased the electrochemical properties of the cathode. The oxidizing agent of LiOH treated high surface area of activated carbon was used for the cathode material for EDLC (electric double layer capacitor) to determine its electrochemical properties and the as-prepared electrode retained excellent performance after 10 cycles and 100 cycles. The anodic and cathodic peak current value and peak segregation of Li-YP80F were better than those of the other two samples, due to the micropore-size and physical properties of the sample. The oxidation peak current value appeared at 0.0055 mA/cm² current density and the reduction peak value at –0.0014 mA/cm², when the Li-YP80F sample used to the Cu-foil surface. The redox peaks appeared at 0.0025 mA/cm² and –0.0009 mA/cm², in the case of using a Nickel foil, after 10 cycling test. The electrochemical stability of cathode materials was tested by 100 recycling tests. After 100 recycling tests, peak current drop decreased the peak profile became stable. The LiOH-treated high surface area of activated carbon had synergistically upgraded electrochemical activity and superior cycling stability that were demonstrated in EDLC.

Impact of electrode micro- and nano-scale topography on the formation and performance of microbial electrodes

From a fundamental standpoint, microbial electrochemistry is unravelling a thrilling link between life and materials. Technically, it may be the source of a large number of new processes such as microbial fuel cells for powering remote sensors, autonomous sensors, microbial electrolysers and equipment for effluent treatment. Microbial electron transfers are also involved in many natural processes such as biocorrosion. In these contexts, a huge number of studies have dealt with the impact of electrode materials, coatings and surface functionalizations but very few have focused on the effect of the surface topography, although it has often been pointed out as a key parameter impacting the performance of electroactive biofilms. The first part of the review gives an overview of the influence of electrode topography on abiotic electrochemical reactions. The second part recalls some basics of the effect of surface topography on bacterial adhesion and biofilm formation, in a broad domain reaching beyond the context of electroactivity. On these well-established bases, the effect of surface topography is reviewed and analysed in the field of electroactive biofilms. General trends are extracted and fundamental questions are pointed out, which should be addressed to boost future research endeavours. The objective is to provide basic guidelines useful to the widest possible range of research communities so that they can exploit surface topography as a powerful lever to improve, or to mitigate in the case of biocorrosion for instance, the performance of electrode/biofilm interfaces.