A simple process for the deposition of TiO 2 onto BDD by electrophoresis and its application to the photoelectrocatalysis of Acid Blue 80 dye

Photoelectrocatalytic degradation of high-density polyethylene microplastics on TiO2-modified boron-doped diamond photoanode

Microplastic (MP) accumulation in the environment is accelerating rapidly, which has led to their effects on both the ecosystem and human life garnering much attention. This study is the first to examine the degradation of high-density polyethylene (HDPE) MPs via photoelectrocatalysis (PEC) using a TiO2-modified boron-doped diamond (BDD/TiO2) photoanode. This study was divided into three stages: (i) preparation of the photoanode through electrophoretic deposition of synthetic TiO2 nanoparticles on a BDD electrode; (ii) characterization of the modified photoanode using electrochemical, structural, and optical techniques; and (iii) degradation of HDPE MPs by electrochemical oxidation and photoelectrocatalysis on bare and modified BDD electrodes under dark and UV light conditions. The results indicate that the PEC technique degraded 89.91 ± 0.08% of HDPE MPs in a 10-h reaction and was more efficient at a lower current density (6.89 mA cm-1) with the BDD/TiO2 photoanode compared to electrochemical oxidation on bare BDD.

Construction of Z-Scheme TiO2/Au/BDD Electrodes for an Enhanced Electrocatalytic Performance

TiO₂/Au/BDD composites with a Z-scheme structure was prepared by orderly depositing gold (Au) and titanium dioxide (TiO₂) on the surface of a boron-doped diamond (BDD) film using sputtering and electrophoretic deposition methods. It was found that the introduction of Au between TiO₂ and the BDD, not only could reduce their contact resistance, to increase the carrier transport efficiency, but also could improve the surface Hall mobility of the BDD electrode. Meanwhile, the designed Z-scheme structure provided a fast channel for the electrons and holes combination, to promote the effective separation of the electrons and holes produced in TiO₂ and the BDD under photoirradiation. The electrochemical characterization elucidated that these modifications of the structure obviously enhanced the electrocatalytic performance of the electrode, which was further verified by the simulated wastewater degradation experiments with reactive brilliant red X-3B. In addition, it was also found that the photoirradiation effectively enhanced the pollution degradation efficiency of the modified electrode, especially for the TiO₂/Au/BDD-30 electrode.

Photoelectrocatalytic degradation of diclofenac with a boron-doped diamond electrode modified with titanium dioxide as a photoanode

The electrophoretic deposition of titanium dioxide (TiO₂) nanoparticles (Degussa P25) onto a boron-doped diamond (BDD) substrate was carried out to produce a photoanode (TiO₂/BDD) to apply in the degradation and mineralization of sodium diclofenac (DCF-Na) in an aqueous medium using photoelectrocatalysis (PEC). This study was divided into three stages: i) photoanode production through electrophoretic deposition using three suspensions (1.25%, 2.5%, 5.0% w/v) of TiO₂ nanoparticles, applying 4.8 V for 15 and 20 s; ii) characterization of the TiO₂/BDD photoanode using scanning electron microscopy and cyclic voltammetry response with the [Fe(CN)₆]^3-/4- redox system; iii) degradation of DCF-Na (25 mg L^-1) through electrochemical oxidation (EO) on BDD and PEC on TiO₂/BDD under dark and UVC-light conditions. The degradation of DCF-Na was evaluated using high-performance liquid chromatography and UV-Vis spectroscopy, and its mineralization measured using total organic carbon and chemical oxygen demand. The results showed that after 2 h, DCF-Na degradation and mineralization reached 98.5% and 80.1%, respectively, through PEC on the TiO₂/BDD photoanode at 2.2 mA cm^-2 under UVC illumination, while through EO on BDD applying 4.4 mA cm^-2, degradation and mineralization reached 85.6% and 76.1%, respectively. This difference occurred because of the optimal electrophoretic formation of a TiO₂ film with a 9.17 μm thickness on the BDD (2.5% w/v TiO₂, time 15 s, 4.8 V), which improved the electrocatalysis and oxidative capacity of the TiO₂/BDD photoanode. Additionally, PEC showed a lower specific energy consumption (1.55 kWh m^-3). Thus, the use of nanostructured TiO₂ films deposited on BDD is an innovative photoanode alternative for the photoelectrocatalytic degradation of DCF-Na, which substantially improves the degradation capacity of bare BDD.

Decolorization and Oxidation of Acid Blue 80 in Homogeneous and Heterogeneous Phases by Selected AOP Processes

This paper is a kinetic study that compares the rate of decolorization and subsequently the mineralization of Acid Blue 80 in model dyeworks wastewater, both in the homogeneous phase using the Fenton and photo-Fenton reactions, UV-C and UVC/H2O2 processes, and in the heterogeneous phase, where the proven commercial photocatalysts P25, P90, and AV01 based on TiO2 were used. The influence of pH of the environment was studied and in the case of the Fenton reaction, the influence of the concentration of catalyzing Fe2+ ions on the rate of decolorization of the model wastewater was also studied. The optimal molar ratio of H2O2/Fe2+ was 10:1. For describing the reaction kinetics, first-order speed constants were best-suited. In all applied processes, the dye chromophore degraded, which was accompanied by a quantitative decolorization of the model wastewater. Subsequently, the mineralization of colorless intermediate products was studied through a decrease in COD or, more precisely, TOC. The mineralization efficiency in the homogeneous phase ranged between 18.6 and 97.1% after 24 h. In the case of heterogeneous photocatalysis, it ranged between 79.6 and 97.3% after 24 h, with efficiency declining in the order P90 > P25 > AV01.

Photoelectrochemical oxygen evolution with interdigitated array electrodes: the example of TiO2

The catalytic reactions of photoelectrochemical water splitting attracts tremendous attention as a promising strategy for clean energy production. And the research on reaction mechanism is particularly important in design and developing new catalysts. In this work, the special electrochemical tool of interdigitated array (IDA) electrodes was utilized in investigating the photoelectrochemical oxygen evolution reaction process and detecting the reaction productin situwith the generation-collection mode. TiO₂was taken as a model catalyst and was decorated onto the IDA generator electrode through an electrophoresis method, so that the photoelectrochemical water splitting can take place on the IDA generator and the reaction product can be detected directly with the IDA collector in real time. It is found that TiO₂can be successfully decorated onto the surface of IDA electrode with the expected photoelectrochemical activity, and the generation-collection mode reveals and distinguishes the production of O₂from the overall photoelectrochemical current on TiO₂generator. The mass transfer process of O₂from the TiO₂generator to the collector could be observed as well. Large overall current at high potential range indicates the possible increasing production of the byproducts or nonfaradaic current.

Fundamentals and applications of photoelectrocatalysis as an efficient process to remove pollutants from water: A review

Water pollution is an environmental problem in constant raising because of population growing, industrial development, agricultural frontier expansion, and principally because of the lack of wastewater treatment technology to remove organic recalcitrant and toxic pollutants from industrial and domestic wastewater. Recalcitrant compounds are a serious environmental and health problem mainly due to their toxicity and potential hazardous effects on living organisms, including human beings. Conventional wastewater treatments have not been able to remove efficiently pollutants from water; however, electrochemical advanced oxidation processes (EAOPs) are able to solve this environmental concern. One of the most recent EAOPs technology is photoelectrocatalysis (PEC), it consists in applying an external bias potential to a semiconductor film placed over a conductive substrate to avoid the recombination of photogenerated electron-hole (e^-/h⁺) pairs, increasing h⁺ availability and hydroxyl radicals' formation, responsible for promoting the degradation/mineralization of organic pollutants in aqueous medium. This review summarizes the recent advances in PEC as a promising technology for wastewater treatment. It addresses the fundamentals and kinetic aspects of PEC. An analysis of photoanode materials and of the configuration of photoelectrochemical reactors is also presented, including an analysis of the influence of the main operational parameters on the treatment of contaminated water. Finally, the most recent applications of PEC are reviewed, and the challenges and perspectives of PEC in wastewater treatment are discussed.

Photoelectrocatalytic degradation of glyphosate on titanium dioxide synthesized by sol-gel/spin-coating on boron doped diamond (TiO2/BDD) as a photoanode

The construction of a photoanode with several layers of titanium oxysulfate as a precursor to form titanium dioxide-TiO2 on boron doped diamond-BDD (TiO2/BDD), and its application for the photoelectro-degradation of glyphosate in aqueous medium are presented. The study was divided into three stages: i) optimization of the number of layers of the TiO2 precursor to modify BDD using a novel method combining Sol-gel/Spin-Coating; ii) characterization of the TiO2/BDD electrodes, by scanning electron microscopy-SEM, dispersive energy spectroscopy-EDX, Ray diffraction-XRD, contact angle, and electrochemical response by cyclic voltammetry using [Fe(CN)6]3-/4- system; iii) degradation of glyphosate (50 mg L-1) by electrochemical oxidation on BDD and photoelectrocatalysis on TiO2/BDD in dark and UV-light conditions, at different current densities, for 5 h. The glyphosate degradation and mineralization were evaluated by High-Performance Liquid Chromatography, Total Organic Carbon, Chemical Oxygen Demand and inorganic-ions concentration (NO3-, PO43-, and NH4+). Also, the aminomethylphosphonic acid-AMPA was quantified by HPLC, as a degradation intermediate. Using five layers of the TiO2 precursor, in the construction of TiO2/BDD photoanode, and a lower contact angle, greater photoelectrocatalysis against the [Fe(CN)6]3-/4- redox system and better degradation of glyphosate compared to BDD without modification were achieved. The formation of TiO2 nanoparticles (14.79 ± 3.43 nm) in anatase phase on BDD was verified by SEM and XRD. Additionally, glyphosate degradation and mineralization were 2.3 times faster by photoelectrocatalysis on TiO2/BDD, relative to BDD, at 3 mA cm-2 and UV-light. Thus, the presence of TiO2 on BDD increases the rate and efficiency of glyphosate degradation with respect to electrochemical oxidation on BDD.

RSM-Based Preparation and Photoelectrocatalytic Performance Study of RGO/TiO2 NTs Photoelectrode

In this paper, reduced graphene oxide (RGO) was prepared by a modified Hummers method and chemical reduction method, and an RGO/TiO2 NTs (RGO/TiO2 nanotubes) photoelectrode was prepared by the electrochemical deposition method. The as-prepared RGO/TiO2 NTs were analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD), and their photocatalytic activities were investigated by measuring the degradation of methylene blue (MB) under simulated solar light irradiation. The SEM and XRD results indicated that the original tubular structure of TiO2-NTs was not changed after RGO modification. The surface of the TiO2 NTs photoelectrode was covered with a non-uniform, flake-shaped reduced graphene oxide film. The thickness of the RGO/TiO2 NTs was increased to about 22.60 nm. The impedance of the RGO/TiO2 NTs was smaller than that of the TiO2 NT photoelectrode. The optimal preparation conditions of RGO/TiO2 NT photoelectrodes were investigated by using a single factor method and response surface method. The best preparation conditions were as follows: deposition potential at 1.19 V, deposition time of 10.27 min, and deposition temperature at 24.94 °C.

Influence of ruthenium doping on UV- and visible-light photoelectrocatalytic color removal from dye solutions using a TiO2 nanotube array photoanode

The photocatalytic activity of TiO₂ anodes was enhanced by synthesizing Ru-doped Ti|TiO₂ nanotube arrays. Such photoanodes were fabricated via Ti anodization followed by Ru impregnation and annealing. The X-ray diffractograms revealed that anatase was the main TiO₂ phase, while rutile was slightly present in all samples. Scanning electron microscopy evidenced a uniform morphology in all samples, with nanotube diameter ranging from 60 to 120 nm. The bias potential for the photoelectrochemical (PEC) treatment was selected from the electrochemical characterization of each electrode, made via linear sweep voltammetry. All the Ru-doped TiO₂ nanotube array photoanodes showed a peak photocurrent (PP) and a saturation photocurrent (SP) upon their illumination with UV or visible light. In contrast, the undoped TiO₂ nanotubes only showed the SP, which was higher than that reached with the Ru-doped photoanodes using UV light. An exception was the Ru(0.15 wt%)-doped TiO₂, whose SP was comparable under visible light. Using that anode, the activity enhancement during the PEC treatment of a Terasil Blue dye solution at E_bias(PP) was much higher than that attained at E_bias(SP). The percentage of color removal at 120 min with the Ru(0.15 wt%)-doped TiO₂ was 98% and 55% in PEC with UV and visible light, respectively, being much greater than 82% and 28% achieved in photocatalysis. The moderate visible-light photoactivity of the Ru-doped TiO₂ nanotube arrays suggests their convenience to work under solar PEC conditions, aiming at using a large portion of the solar spectrum.

Advances in Template Prepared Nano-Oxides and their Applications: Polluted Water Treatment, Energy, Sensing and Biomedical Drug Delivery

The nano-oxide materials with special structures prepared by template methods have a good dispersion, regular structures and high specific surface areas. Therefore, in some areas, improved properties are observed than conventional bulk oxide materials. For example, in the treatment of dye wastewater, the treatment efficiency of adsorbents and catalytic materials prepared by template method was about 30 % or even higher than that of conventional samples. This review mainly focuses on the progress of inorganic, organic and biological templates in the preparation of micro- and nano- oxide materials with special morphologies, and the roles of the prepared materials as adsorbents and photocatalysts in dye wastewater treatment. The characteristics and advantages of inorganic, organic and biological template are also summarized. In addition, the applications of template method prepared oxides in the field of sensors, drug carrier, energy materials and other fields are briefly discussed with detailed examples.