TiO2/reduced graphene oxide nanocomposite as efficient ascorbic acid amperometric sensor

3D-printed sensor decorated with nanomaterials by CO2 laser ablation and electrochemical treatment for non-enzymatic tyrosine detection

The combination of CO₂ laser ablation and electrochemical surface treatments is demonstrated to improve the electrochemical performance of carbon black/polylactic acid (CB/PLA) 3D-printed electrodes through the growth of flower-like Na₂O nanostructures on their surface. Scanning electron microscopy images revealed that the combination of treatments ablated the electrode's polymeric layer, exposing a porous surface where Na₂O flower-like nanostructures were formed. The electrochemical performance of the fabricated electrodes was measured by the reversibility of the ferri/ferrocyanide redox couple presenting a significantly improved performance compared with electrodes treated by only one of the steps. Electrodes treated by the combined method also showed a better electrochemical response for tyrosine oxidation. These electrodes were used as a non-enzymatic tyrosine sensor for quantification in human urine samples. Two fortified urine samples were analyzed, and the recovery values were 106 and 109%. The LOD and LOQ for tyrosine determination were 0.25 and 0.83 μmol L^-1, respectively, demonstrating that the proposed devices are suitable sensors for analyses of biological samples, even at low analyte concentrations.

Reduced graphene oxide on silver nanoparticle layers-decorated titanium dioxide nanotube arrays as SERS-based sensor for glyphosate direct detection in environmental water and soil

When glyphosate, a widely used organophosphate herbicide in agricultural applications, contaminates the environment, it could lead to chronic harm to human health. Herein, an efficient, air-stable and reusable surface-enhanced Raman scattering (SERS) substrate was designed to be an analytical tool for direct determination of glyphosate. A vertical heterostructure of reduced graphene oxide (rGO)-wrapped dual-layers silver nanoparticles (AgNPs) on titania nanotube (TiO2 NTs) arrays was constructed as a SERS substrate. The TiO2 NTs/AgNPs-rGO exhibited high SERS performance for methylene blue detection, offering an analytical enhancement factor (AEF) as large as 7.1 × 108 and the limit of detection (LOD) as low as 10-14 M with repeatability of 4.4 % relative standard deviation (RSD) and reproducibility of 2.0 % RSD. The sensor was stable in ambient and was reusable after photo-degradation. The designed sensor was successfully applied for glyphosate detection with a LOD of 3 µg/L, which is below the maximum contaminant level of glyphosate in environmental water, as recommended by the U.S. EPA and the European Union. A uniqueness of this study is that there is no significant difference between the real-world applications of the SERS sensor on direct glyphosate analysis in environmental samples compared to an analysis using ultra-high performance liquid chromatography.

Ultrathin g-C3N4 nanosheet-CoOOH nanocomposite for fluorescence imaging of ascorbic acid in living cells

Ascorbic acid (AA), a critical cellular metabolite involved in many biochemical pathways, is an important antioxidant in human body. Therefore, it is of great significance to monitor AA in living cells. Nowadays, there are various technologies developed for the detection of AA, but few methods could sensitively and selectively detect the intracellular AA. Here, we reported a highly efficient biosensor (g-C₃N₄-CoOOH nanocomposite) based on ultrathin graphitic carbon nitride (g-C₃N₄) nanosheets and CoOOH nanoflakes, for sensitive detection and fluorescence imaging of AA in living cell. The g-C₃N₄ used here as fluorescence donor is a promising bioimaging nanomaterial because of their high fluorescence quantum yield, good biocompatibility and low toxicity. In addition, the CoOOH was used to be perfect fluorescence quencher. Herein, we enabled the CoOOH in situ to form a layer on the surface of g-C₃N₄, resulting in fluorescence quench of the g-C₃N₄. Upon the addition of AA, the CoOOH nanoflakes were reduced to Co²⁺, and the system gave a "turn on" fluorescence signal. It developed as an efficient sensing platform for AA, and the linear range was from 5 to 50 μM with a 1.6 μM detection limit. This novel biosensor, g-C₃N₄-CoOOH nanocomposite exhibited highly selective response toward AA relative to other biomolecules. Furthermore, this biosensor was used successfully to visualize and monitor AA in living cells. Hopefully, we believe that this biosensor would provide a low-cost and highly sensitive platform for AA detection and bioimaging. Schematic illustration of the sensing strategy based on the g-C₃N₄-CoOOH nanocomposite for AA detection.

Carbon nanostructures: a comprehensive review of potential applications and toxic effects

There is no doubt that nanotechnology has revolutionized our life since the 1970s when it was first introduced. Nanomaterials have helped us to improve the current products and services we use. Among the different types of nanomaterials, the application of carbon-based nanomaterials in every aspect of our lives has rapidly grown over recent decades. This review discusses recent advances of those applications in distinct categories, including medical, industrial, and environmental applications. The first main section introduces nanomaterials, especially carbon-based nanomaterials. In the first section, we discussed medical applications, including medical biosensors, drug and gene delivery, cell and tissue labeling and imaging, tissue engineering, and the fight against bacterial and fungal infections. The next section discusses industrial applications, including agriculture, plastic, electronic, energy, and food industries. In addition, the environmental applications, including detection of air and water pollutions and removal of environmental pollutants, were vastly reviewed in the last section. In the conclusion section, we discussed challenges and future perspectives.

A portable ascorbic acid in sweat analysis system based on highly crystalline conductive nickel-based metal-organic framework (Ni-MOF)

Conductive metal-organic frameworks can provide unique porous structures, large pore volumes, many catalytically active sites and high crystallinity, and so are becoming increasingly important and attractive as electrocatalytic materials. The present work synthesized nanorods of the conductive compound Ni₃(2,3,6,7,10,11-hexaiminotriphenylene)₂ (Ni₃(HITP)₂) with a high degree of crystallinity from HITP ligands and Ni²⁺ ions. Screen-printed electrodes made with this material were employed to fabricate an enzyme-free sensor for the detection of ascorbic acid (AA). The sensor exhibited good catalytic activity during the electrocatalytic analysis of AA in alkaline media, attributed to the synergistic effect of highly active Ni-N₄ catalytic sites in the nanorods, the two-dimensional superimposed honeycomb lattice of the Ni₃(HITP)₂, and the large specific surface area of this material. The latter property facilitated efficient electron transfer during catalytic oxidation. A portable electrochemical AA detection system was developed using Ni₃(HITP)₂ as the electrode material together with application-specific integrated circuits and a smartphone application with App. Good sensing performance was obtained, including a wide linear range (2-200 μM) with high sensitivity (0.814 μA μM^-1 cm^-2), and low detection limit (1 μM). This system can be used to monitor AA levels and trends in sweat to assess vitamin C intake as a part of personal health management.

Titania (TiO2)/silica (SiO2) nanospheres or NSs amalgamated on a pencil graphite electrode to sense l-ascorbic acid electrochemically and augmented NSs for antimicrobial behaviour

Synthesis of TiO2@SiO2 nanospheres, modification on a pencil graphite electrode, electrochemical sensing study of the modified electrode for ascorbic acid detection and antimicrobial study of nanospheres have been investigated.

Photocatalysis of dichlorvos using graphene oxide-TiO2nanocomposite under visible irradiation: process optimization using response surface methodology

Graphene oxide-TiO₂nanocomposite (GOT) was used for degradation and mineralization of dichlorvos, an organophosphorus pesticide, from aqueous solution under visible irradiation. The nanocomposite was characterized by scanning electron microscopy, transmission electron microscopy, UV-DRS, Fourier-transform infrared spectroscopy, Raman spectroscopy, and x-ray photoelectron spectroscopy. Anatase phase TiO₂nanoparticles (10-20 nm in diameter) were present in the nanocomposite. The nanoparticles were uniformly distributed on reduced GO sheets. A three-factor face-centered central composite design with response surface methodology was used for modeling and optimization of various variables that may potentially affect photodegradation, i.e. pH, catalyst loading, and initial dichlorvos concentration. A quadratic model was built to predict degradation, mineralization efficiency, and reaction rate constant. The experimental and predicted values depicted a good correlation and the utility of the models was confirmed by the highF-values observed for the degradation and mineralization models. High coefficient of determination (R²) was obtained for the degradation (R² = 0.95) and mineralization (R² = 0.93) models. Pareto analysis was carried out to determine the effect of each variable on photocatalytic degradation and mineralization. The predicted results suggested that the optimum conditions for obtaining maximum degradation (69%) and mineralization (64%) were: initial dichlorvos concentration of 0.5 mg l^-1with a catalyst dose of 110 mg l^-1at pH 6.5. The main effect plots also suggested a significant influence of the variables used in the photocatalysis of dichlorvos by GOT.

N-Hydroxysuccinimide crosslinked graphene oxide–gold nanoflower modified SPE electrode for sensitive detection of chloramphenicol antibiotic

Here we introduce a composite material that consists of graphene oxide (GO) sheets crosslinked with N-hydroxysuccinimide (NHS) and functionalized with gold nanoflowers (AuNFs). Furthermore, a screen printed electrode (SPE) modified with the introduced composite is electrochemically reduced to obtain an SPE/rGO–NHS–AuNFs electrode for sensitive and selective determination of chloramphenicol (CAP) antibiotic drug. The morphological structure of the as-prepared nanocomposite was characterized by scanning electron microscopy, energy-dispersive X-ray spectroscopy, cyclic voltammetry, Fourier-transform infrared spectroscopy and electrochemical impedance spectroscopy. The proposed sensor demonstrated excellent performance with a linear concentration range of 0.05 to 100 μM and a detection limit of 1 nM. The proposed electrode offers a high level of selectivity, stability, reproducibility and a satisfactory recovery rate for electrochemical detection of CAP in real samples such as blood serum, poultry feed, milk, eggs, honey and powdered milk samples. This further demonstrates the practical feasibility of the proposed sensor in food analysis.

Here we introduce a composite material that consists of graphene oxide (GO) sheets crosslinked with N-hydroxysuccinimide (NHS) and functionalized with gold nanoflowers (AuNFs).

Computational studies and biosensory applications of graphene-based nanomaterials: a state-of-the-art review

Graphene, graphene oxide (GO) and graphene quantum dots (GQDs) are expected to play a vital role in the diagnosis of severe ailments. Computer-based simulation approaches are helpful for understanding theoretical tools prior to experimental investigation. These theoretical tools still have a high computational requirement. Thus, more efficient algorithms are required to perform studies on even larger systems. The present review highlights the recent advancement in structural confinement using computer simulation approaches along with biosensory applications of graphene-based materials. The computer simulation approaches help to identify the interaction between interacting molecules and sensing elements like graphene sheets. The simulation approach reduces the wet-lab experiment time and helps to predict the interaction and interacting environment. The experimental investigation can be tuned at a molecular level easily to predict small changes in structural configuration. Here, the molecular simulation study could be useful as an alternative to actual wet experimental approaches. The sensing ability of graphene-based materials is a result of interactions like hydrogen bonding, base-base interaction, and base-to-pi interaction to name a few. These interactions help in designing and engineering a substrate for sensing of various biomolecules.

Electrochemical detection of ascorbic acid in artificial sweat using a flexible alginate/CuO-modified electrode

A flexible sensor is presented for electrochemical detection of ascorbic acid in sweat based on single-step modified gold microelectrodes. The modification consists of electrodeposition of alginate membrane with trapped CuO nanoparticles. The electrodes are fabricated at a thin polyimide support and the soft nature of the membrane can withstand mechanical stress beyond requirements for skin monitoring. After characterization of the membrane via optical and scanning electron microscopy and cyclic voltammetry, the oxidative properties of CuO are exploited toward ascorbic acid for amperometric measurement at micromolar levels in neutral buffer and acidic artificial sweat, at ultralow applied potential (- 5 mV vs. Au pseudo-reference electrode). Alternatively, measurement of the horizontal shift of redox peaks by cyclic voltammetry is also possible. Obtaining a limit of detection of 1.97 μM, sensitivity of 0.103 V log (μM)^-1 of peak shift, and linear range of 10-150 μM, the effect of possible interfering species present in sweat is minimized, with no observable cross-reaction, thus maintaining a high degree of selectivity despite the absence of enzymes in the fabrication scheme. With a lateral flow approach for sample delivery, repeated measurements show recovery in few seconds, with relative standard deviation of about 20%, which can serve to detect increased loss or absence of vitamin, and yet be improved in future by optimized device designs. This sensor is envisioned as a promising component of wearable devices for e.g. non-invasive monitoring of micronutrient loss through sweat, comprising features of light weight, low cost, and easy fabrication needed for such application. Graphical Abstract Schematic depiction of the cyclic voltammetry signal change as the sweat flows over the sensor surface.

An amperometric biosensor based on poly(L-aspartic acid), nanodiamond particles, carbon nanofiber, and ascorbate oxidase-modified glassy carbon electrode for the determination of L-ascorbic acid

An amperometric L-ascorbic acid biosensor utilizing ascorbate oxidase (AOx) immobilized onto poly(L-aspartic acid) (P(L-Asp)) film was fabricated on carbon nanofiber (CNF) and nanodiamond particle (ND)-modified glassy carbon electrode (GCE). Effects of AOx, ND, and CNF amounts were investigated by monitoring the response currents of the biosensor at different amounts of AOx, ND, and CNF. The electropolymerization step of L-aspartic acid on CNF-ND/GCE surface was also optimized. Scanning electron microscopy (SEM), cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS) techniques were used to enlighten the modification steps of the biosensor. The effects of pH and applied potential were studied in detail to achieve the best analytical performance. Under optimized experimental conditions, the AOx/P(L-Asp)/ND-CNF/GCE biosensor showed a linear response to L-ascorbic acid in the range of 2.0 × 10^-7-1.8 × 10^-3 M with a detection limit of 1.0 × 10^-7 M and sensitivity of 105.0 μAmM^-1 cm^-2. The novel biosensing platform showed good reproducibility and selectivity. The strong interaction between AOx and the P(L-Asp)/ND-CNF matrix was revealed by the high repeatability (3.4%) and good operational stability. The AOx/P(L-Asp)/ND-CNF/GCE biosensor was successfully applied to the determination of L-ascorbic acid in vitamin C effervescent tablet and pharmaceutical powder containing ascorbic acid with good results, which makes it a promising approach for quantification of L-ascorbic acid. Graphical abstract.

One-step rapid synthesis of Ni6(C12H25S)12 nanoclusters for electrochemical sensing of ascorbic acid

Metal nanoclusters (NCs) are highly desirable as active catalysts due to their highly active surface atoms. Among the reported metal clusters, nickel nanoclusters (Ni NCs) have been less well developed than others, such as gold, silver and copper. Herein a simple method is developed to synthesize atomically precise Ni clusters with the molecular formular of Ni₆(C₁₂H₂₅S)₁₂. Moreover, the single crystal of the Ni₆(C₁₂H₂₅S)₁₂ cluster is also obtained. The composition, morphology and optical properties of the prepared Ni₆ clusters are characterized by X-ray crystallography, XPS, XRD, SEM, HRTEM, FTIR and UV-Vis spectroscopy. The Ni cluster is composed of six nickel atoms that form a hexagonal ring with an exterior 1-dodecanethiol shell, resembling a double crown. Meanwhile, the Ni₆ NCs can be self-assembled into nanosheets due to their uniform size. It was found that the Ni₆(C₁₂H₂₅S)₁₂ clusters loaded on carbon black exhibit higher electrocatalytic activity than Ni nanoparticles towards ascorbic acid (AA) oxidation. The Ni₆ clusters show high sensing performance for AA with a wide linear range (1-3212 μM) and a low detection limit of 0.1 μM (S/N = 3). The significantly enhanced catalytic activity can be ascribed to the high fraction of surface Ni atoms with low coordination in the sub-nanometer clusters. The present work not only provides a straightforward method for synthesizing atomically precise metal clusters but also indicates that ultrasmall Ni clusters can be used as highly efficient catalysts for the electrochemical detection of AA.

Design of a new electrochemical sensing system based on MoS2–TiO2/reduced graphene oxide nanocomposite for the detection of paracetamol

Synthetic route for the MoS₂–TiO₂/rGO nanocomposite and the electrode reaction for paracetamol.