An efficient platform for the electrooxidation of formaldehyde based on amorphous NiWO4 nanoparticles modified electrode for fuel cells

NiCo-LDH coupled with 2D ZIF-derived Co nitrogen doped carbon nanosheet arrays as a self-supporting electrocatalyst for detection of formaldehyde

Formaldehyde is susceptible to illegal addition to foodstuffs to extend their shelf life due to its antimicrobial, preservative and bleaching properties. In this study, a self-supporting "nanosheet on nanosheet" arrays electrocatalyst with core-shell heterostructure was prepared in situ by coupling NiCo layer double hydroxide with 2D ZIF derived Co-nitrogen-doped porous carbon on carbon cloth (Co-N/C@NiCo-LDH NSAs/CC). Co-N/C nanosheet arrays act as a scaffold core with good electrical conductivity, providing more NiCo-LDH nucleation sites to avoid NiCo-LDH agglomeration, thus having fast mass/charge transfer performance. While the NiCo-LDH nanosheet arrays shell with high specific surface area provide more active sites for electrochemical reactions. As an electrocatalytic sensing electrode, Co-N/C@NiCo-LDH NSAs/CC has a wide linear range of 1 μM to 13 mM for formaldehyde detection, and the detection limit is 82 nM. Besides, the sensor has been applied to the detection of formaldehyde in food samples with satisfactory results.

A new method for the preparation of MgAl layered double hydroxide-copper metal-organic frameworks structures: application to electrocatalytic oxidation of formaldehyde

In this research, we present a novel design protocol for the in-situ synthesis of MgAl layered double hydroxide-copper metal-organic frameworks (LDH-MOFs) nanocomposite based on the electrocoagulation process and chemical method. The overall goal in this project is the primary synthesis of para-phthalic acid (PTA) intercalated MgAl-LDH with Cu (II) ions to produce the paddle-wheel like Cu-(PTA) MOFs nanocrystals on/in the MgAl-LDH structure. The physicochemical properties of final product; Cu-(PTA) MOFs/MgAl-LDH, were characterized by the surface analysis and chemical identification methods (SEM, EDX, TEM, XRD, BET, FTIR, CHN, DLS, etc.). The Cu-(PTA) MOFs/MgAl-LDH nanocomposite was used to modification of the carbon paste electrode (CPE); Cu-(PTA) MOFs/MgAl-LDH/CPE. The electrochemical performance of Cu-(PTA) MOFs/MgAl-LDH/CPE was demonstrated through the utilization of electrochemical methods. The results show a stable redox behavior of the Cu (III)/Cu (II) at the surface of Cu-(PTA) MOFs/MgAl-LDH/CPE in alkaline medium (aqueous 0.1 M NaOH electrolyte). Then, the Cu-(PTA) MOFs/MgAl-LDH/CPE was used as a new electrocatalyst toward the oxidation of formaldehyde (FA). Electrochemical data show that the Cu-(PTA) MOFs/MgAl-LDH/CPE exhibits superior electrocatalytic performance on the oxidation of FA. Also the diffusion coefficient, exchange current density (J°) and mean value of catalytic rate constant (Kcat) were found to be 1.18 × 10-6 cm2 s-1, 23 mA cm-2 and 0.4537 × 104 cm3 mol-1 s-1, respectively. In general, it can be said the Cu-(PTA) MOFs/MgAl-LDHs is promising candidate for applications in direct formaldehyde fuel cells.

Recent Advances in Electrochemical Sensors for Formaldehyde

Formaldehyde, a ubiquitous indoor air pollutant, plays a significant role in various biological processes, posing both environmental and health challenges. This comprehensive review delves into the latest advancements in electrochemical methods for detecting formaldehyde, a compound of growing concern due to its widespread use and potential health hazards. This review underscores the inherent advantages of electrochemical techniques, such as high sensitivity, selectivity, and capability for real-time analysis, making them highly effective for formaldehyde monitoring. We explore the fundamental principles, mechanisms, and diverse methodologies employed in electrochemical formaldehyde detection, highlighting the role of innovative sensing materials and electrodes. Special attention is given to recent developments in nanotechnology and sensor design, which significantly enhance the sensitivity and selectivity of these detection systems. Moreover, this review identifies current challenges and discusses future research directions. Our aim is to encourage ongoing research and innovation in this field, ultimately leading to the development of advanced, practical solutions for formaldehyde detection in various environmental and biological contexts.

A wireless smartphone-based "tap-and-detect" formaldehyde sensor with disposable nano-palladium grafted laser-induced graphene (nanoPd@LIG) electrodes

We developed a fully integrated smart sensing device for on-site testing of food to detect trace formaldehyde (FA). A nano-palladium grafted laser-induced graphene (nanoPd@LIG) composite was synthesized by one-step laser irradiation of a Pd²⁺-chitosan-polyimide precursor. The composite was synthesized in the form of a three-electrode sensor on a polymer substrate. The electrochemical properties and morphology of the fabricated composite were characterized and the electrochemical kinetics of FA oxidation at the nanoPd@LIG electrode were investigated. The nanoPd@LIG electrode was combined with a smart electrochemical sensing (SES) device to determine FA electrochemically. The proposed SES device uses near field communication (NFC) to receive power and transfer data between a smartphone interface and a battery-free sensor. The proposed FA sensor exhibited a linear detection range from 0.01 to 4.0 mM, a limit of detection of 6.4 μM, good reproducibility (RSDs between 2.0 and 10.1%) and good anti-interference properties for FA detection. The proposed system was used to detect FA in real food samples and the results correlated well with the results from a commercial potentiostat and a spectrophotometric analysis.

Fluorometric Sensing and Detection of p-Nitroaniline by Mixed Metal (Zn, Ni) Tungstate Nanocomposite

Aromatic amines are important chemical intermediates that hold an irreplaceable significance for synthesizing many chemical products. However, they may react with substances excreted from human bodies to generate blood poisoning, skin eczema, and dermatitis disease and even induce cancer-causing high risks to human health and the environment. Metal tungstates have been proven to be highly efficient materials for developing various toxic gases or chemical detection sensor systems. However, the major factors of the sensors, such as sensitivity, selectivity, stability, response, and recovery times, still need to be optimized for practical technological applications. In this work, Ni-doped ZnWO₄ mixed metal tungstate nanocomposite material was synthesized by the hydrothermal method and explored as a sensor for the fluorometric determination of p-nitroaniline (p-NA). Transmission electron microscopy (TEM) was used for the elucidation of the optimized particle diameter. Scanning electron microscopy (SEM) was employed to observe the surface morphological changes in the material during the solid-state reactions. The vibration modes of as-prepared samples were analyzed using Fourier-transform infrared spectroscopy (FTIR). The chemical bonding and oxidation states of individual elements involved in material synthesis were observed using X-ray photoelectron spectroscopy (XPS). The PL activities of the metal tungstate nanoparticles were investigated for the sensing of p-nitroaniline (p-NA). The obtained results demonstrated that ZnNiWO₄ was more effective in sensing p-NA than the other precursors were by using the quenching effect. The material showed remarkably high sensitivity towards p-NA in a concentration range of 25-1000 μM, and the limit of detection (LOD) value was found to be 1.93 × 10^-8 M for ZnWO₄, 2.17 × 10^-8 M for NiWO₄, and 2.98 × 10^-8 M for ZnNiWO₄, respectively.

Bismuth-coated screen-printed electrodes for the simple voltammetric determination of formaldehyde

For the first time, bismuth modified electrodes have been used for the voltammetric detection of formaldehyde (FM). The well-known method of forming formaldehyde hydrazone (FAH) in the presence of hydrazine sulphate was used to convert the hydrated form of FM into its electrochemically active derivative. Various experimental conditions for differential pulse voltammetry were studied to achieve the best analytical performance. The FAH reduction current (FM response) reaches its maximum value at a pH of a phosphate buffer solution of 5.2 ± 0.1 in the presence of 0.09-0.12 M hydrazine sulfate on a bismuth film preliminarily precipitated for 8-12 min from acidic Bi(III) acetate solutions at an electrolysis potential of -1.0 V on the surface of a screen-printed carbon electrode (SPCE). A dendritic-like film structure was created on the SPCE surface. Under the optimized conditions a linear calibration curve over the range of 0.01-5 mg L^-1 (0.33-167 μM) FM was achieved, with a detection limit of 0.002 mg L^-1 (0.06 μM). The determination of FM in waste water, melt water from snow within the city industrial zone, and a widely used pharmaceutical preparation "Endofalk®" with good results revealed the potential applicability of a bismuth modified SPCE (BiSPCE) for trace analysis.

Bimetallic nickel/manganese phosphate–carbon nanofiber electrocatalyst for the oxidation of formaldehyde in alkaline medium

The development of earth-abundant transition metal-based catalysts, supported by a conductive carbonaceous matrix, has received great attention in the field of conversion of formaldehyde derivatives into toxic-free species. Herein, we report a comprehensive investigation of bimetallic electrocatalyst activity towards the electrooxidation of formaldehyde. The bimetallic phosphate catalyst is prepared by co-precipitation of Ni and Mn phosphate precursors using a simple reflux approach. Then the bimetallic catalyst is produced by mixing the Ni/Mn with carbon fibres (CNFs). The structural properties and crystallinity of the catalyst were investigated by using several techniques, such as scanning electron microscopy, X-ray diffraction, energy-dispersive X-ray spectroscopy, and Brunauer Emmett−Teller theory. The system performance was studied under potentiostatic conditions. Some theoretical thermodynamic and kinetic models were applied to assess the system performance. Accordingly, key electrochemical parameters, including surface coverage (Γ) of active species, charge transfer rate (k_s), diffusion coefficient of the formaldehyde (D), and catalytic rate constant (k_cat) were calculated at Γ = 1.690 × 10⁻⁴ mmol cm⁻², k_s = 1.0800 s⁻¹, D = 1.185 × 10⁻³ cm² s⁻¹ and k_cat = 1.08 × 10⁵ cm³ mol⁻¹ s⁻¹. These findings demonstrate the intrinsic electrocatalytic activity of formaldehyde electrooxidation on nickel/manganese phosphate- CNFs in alkaline medium.

The catalytic performance of bimetallic Ni/Mn phosphate–carbon nanofiber composite catalyst is better than mono metallic catalysts toward electrooxidation of formaldehyde.

Investigation on NiWO4/PANI composite as an electrode material for energy storage devices

NiWO4/PANI was synthesized by an in situ chemical oxidative polymerization route. Incorporation of NiWO4 in a PANI matrix rendered high specific capacitance and salient morphological features.

Visible Light-Driven Photoelectrocatalytic Water Splitting Using Z-Scheme Ag-Decorated MoS2/RGO/NiWO4 Heterostructure

Herein, we have successfully constructed a solid-state Z-scheme photosystem with enhanced light absorption capacity by combining the optoelectrical properties of AgNPs with those of the MoS2/RGO/NiWO4 (Ag-MRGON) heterostructure. The Ag-MRGON Z-scheme system demonstrates improved photo-electrochemical (PEC) water-splitting performance in terms of applied bias photon-to-current conversion efficiency (ABPE), which is 0.52%, and 17.3- and 4.3-times better than those of pristine MoS2 and MoS2/NiWO4 photoanodes, respectively. The application of AgNPs as an optical property enhancer and RGO as an electron mediator improved the photocurrent density of Ag-MRGON to 3.5 mA/cm2 and suppressed the charge recombination to attain the photostability of ∼2 h. Moreover, the photocurrent onset potential of the Ag-MRGON heterojunction (i.e., 0.61 VRHE) is cathodically shifted compared to those of NiWO4 (0.83 VRHE), MoS2 (0.80 VRHE), and MoS2/NiWO4 heterojunction (0.73 VRHE). The improved PEC water-splitting performance in terms of ABPE, photocurrent density, and onset potential is attributed to the facilitated charge transfer through the RGO mediator, the plasmonic effect of AgNPs, and the proper energy band alignments with the thermodynamic potentials of hydrogen and oxygen evolution.