Effect of La doping level on structural and sensing properties of LZO/RGO nanohybrid: Highly selective sensing platform for isoprenaline determinations in the presence of ascorbic acid, uric acid and folic acid

Improvements in the Magnesium Ion Transport Properties of Graphene/CNT-Wrapped TiO2 -B Nanoflowers by Nickel Doping

Magnesium-ion batteries are widely studied for its environmentally friendly, low-cost, and high volumetric energy density. In this work, the solvothermal method is used to prepare titanium dioxide bronze (TiO2 -B) nanoflowers with different nickel (Ni) doping concentrations for use in magnesium ion batteries as cathode materials. As Ni doping enhances the electrical conductivity of TiO2 -B and promotes magnesium ion diffusion, the band gap of TiO2 -B host material can be significantly reduced, and as Ni content increases, diffusion contributes more to capacity. According to the electrochemical test, TiO2 -B exhibits excellent electrochemical performance when the Ni element doping content is 2 at% and it is coated with reduced graphene oxide@carbon nanotube (RGO@CNT). At a current density of 100 mA g-1 , NT-2/RGO@CNT discharge specific capacity is as high as 167.5 mAh g-1 , which is 2.36 times of the specific discharge capacity of pure TiO2 -B. It is a very valuable research material for magnesium ion battery cathode materials.

Different additives of gold nanoparticles and lithium oxide loaded chitosan based films; controlling optical and structural properties, evaluating cell viability

Natural chitosan-based films (CS) were fabricated by changing ingredient corporations between gold nanoparticles (AuNPs), lithium oxide (Li₂O), and graphene oxide (GO). A Series of films with different components were obtained. The structural examination is executed by XRD, FTIR, and EDX to analyze crystal structure, chemical bonding, and chemical contents, respectively. The findings illustrated that, the Li₂O@CS exhibited the lowest contact angle with 70 ± 4.6°. Scanning Electron Microscopy (SEM) displayd rod-shaped AuNPs with an average length of 0.3 μm and an average width of 90 nm. The refractive index of CS recorded 2.142, while AuNPs/Li₂O/GO@CS slightly declined to 2.085. Concerning AuNPs/Li₂O/GO@CS, the detected cell viability percentage of normal lung cells among the usage of 156.25 μg/mL is 98.91%, while 9.77 μg/mL achieved 125.78%. Therefore, combining AuNPs, GO and Li₂O within the CS matrix results in films of boosted biocompatibility and can be suggested for medical applications.

Electrochemical sensors for β-adrenoceptor agonist isoprenaline analysis in human urine and serum samples using manganese cobalt oxide-modified glassy carbon electrode

Schematic illustration for the synthesis of the MCO nanosphere and modification with GCE towards the electrochemical determination of isoprenaline.

Spectroelectrochemical Determination of Isoprenaline in a Pharmaceutical Sample

UV/Vis absorption spectroelectrochemistry (SEC) is a multi-response technique that has been commonly used for the characterization of materials and the study of reaction mechanisms. However, it has been scarcely used for quantitative purposes. SEC allows us to obtain two analytical signals simultaneously, yielding a dual sensor in just one experiment. In the last years, our group has developed new devices useful for analysis. In this work, a SEC device in parallel configuration, based on optical fibers fixed on screen-printed electrodes, was used to determine isoprenaline in a commercial drug, using both, the electrochemical and the spectroscopic signals. In this commercial drug, isoprenaline is accompanied in solution by other compounds. Among them is sodium metabisulfite, an antioxidant that strongly interferes in the isoprenaline determination. A simple pretreatment of the drug sample by bubbling wet-air allows us to avoid the interference of metabisulfite. Here, we demonstrate again the capabilities of UV/Vis absorption SEC as double sensor for analysis and we propose a simple pretreatment to remove interfering compounds.

Selective Detection of Folic Acid Using 3D Polymeric Structures of 3-Carboxylic Polypyrrole

The detection of folic acid in biological samples or pharmaceutical products is of great importance due to its implications in the biological functions of the human body, along with the development and growth of the fetus. The deficiency of folic acid can be reversed by the intake of different pharmaceutical formulations or alimentary products fortified with this molecule. The elaboration of sensing platforms represents a continuous work in progress, a task in which the use of conductive polymers modified with different functionalities represents one of the outcoming strategies. The possibility of manipulating their morphology with the use of templates or surfactants represents another advantage. A sensing platform based on carboxylic functionalized polypyrrole was synthesized via the electrochemical approach in the presence of a polymeric surfactant on a graphite-based surface. The sensor was able to detect the folic acid from 2.5 μM to 200 μM with a calculated limited of detection of 0.8 μM. It was employed for the detection of the analyte from commercial human serum and pharmaceutical products with excellent recovery rates. The results were double checked using an optimized spectrophotometric procedure that confirmed furthermore the performances of the sensor related to real samples assessment.