The distinctive sensing performance of cobalt ion in LaBO3 perovskite (B = Fe, Mn, Ni, or Cr) for hydrazine electrooxidation

Removal of Pb(II) ions by cellulose modified-LaFeO3 sorbents from different biomasses

LaFeO3 perovskite is prepared by the cellulose-modified microwave-assisted citrate method using two different biomasses as a cellulose source; rice straw (RS) and banana peel (BP). The prepared samples are assigned as LaFeO3/cellulose-RS and as LaFeO3/cellulose-BP, respectively. Raman Spectra prove the presence of perovskite and cellulose phases, as well as biochar resulted from the thermal treatment of the cellulose. LaFeO3/cellulose-RS has a cauliflower morphology while, two phases are observed for LaFeO3/cellulose-BP, mesoporous cellulose phase and octahedral LaFeO3 nanoparticles as shown by scanning electron microscope (SEM) images. LaFeO3/cellulose-BP has higher porosity and larger BET surface area than LaFeO3/cellulose-RS. Both samples are applied for the removal of Pb(II) ions from aqueous solution by adsorption. The adsorption follows Langmuir isotherm, with maximum adsorption capacities of 524 and 730 mg/g for LaFeO3/cellulose-RS and LaFeO3/cellulose-BP, respectively. Cellulose precursors from different biomasses affect structural and morphological properties of LaFeO3/cellulose samples as well as the sorption performance for Pb(II) ions. BP is more recommended than RS, as a biomass, in the present study.

A correlation of the adsorption capacity of perovskite/biochar composite with the metal ion characteristics

LaFeO₃/biochar composite is prepared by cellulose-modified microwave-assisted method at 450 °C. The structure is identified by Raman spectrum which, consists of characteristics biochar bands and octahedral perovskite chemical shifts. The morphology is examined by scanning electron microscope (SEM); two phases are observed, rough microporous biochar and orthorhombic perovskite particles. The BET surface area of the composite is 57.63 m²/g. The prepared composite is applied as a sorbent for the removal of Pb²⁺, Cd²⁺, and Cu²⁺ ions from aqueous solutions and wastewater. The adsorption ability reaches a maximum at pH > 6 for Cd²⁺, and Cu²⁺ ions, and is pH-independent for Pb²⁺ ions adsorption. The adsorption follows pseudo 2nd order kinetic model, Langmuir isotherm for Pb²⁺ ions, and Temkin isotherms for Cd²⁺, and Cu²⁺ ions. The maximum adsorption capacities, q_m, are 606, 391, and 112 mg/g for Pb²⁺, Cd²⁺, and Cu²⁺ ions, respectively. The electrostatic interaction is responsible for the adsorption of Cd²⁺, and Cu²⁺ ions on LaFeO₃/biochar composite. In case of Pb²⁺ ions form a complex with the surface functional groups of the adsorbate. LaFeO₃/biochar composite shows high selectivity for the studied metal ions and excellent performance in real samples. The proposed sorbent can be easily regenerated and effectively reused.

Three-Dimensional Electrochemical Sensors for Food Safety Applications

Considering the increasing concern for food safety, electrochemical methods for detecting specific ingredients in the food are currently the most efficient method due to their low cost, fast response signal, high sensitivity, and ease of use. The detection efficiency of electrochemical sensors is determined by the electrode materials' electrochemical characteristics. Among them, three-dimensional (3D) electrodes have unique advantages in electronic transfer, adsorption capacity and exposure of active sites for energy storage, novel materials, and electrochemical sensing. Therefore, this review begins by outlining the benefits and drawbacks of 3D electrodes compared to other materials before going into more detail about how 3D materials are synthesized. Next, different types of 3D electrodes are outlined together with common modification techniques for enhancing electrochemical performance. After this, a demonstration of 3D electrochemical sensors for food safety applications, such as detecting components, additives, emerging pollutants, and bacteria in food, was given. Finally, improvement measures and development directions of electrodes with 3D electrochemical sensors are discussed. We think that this review will help with the creation of new 3D electrodes and offer fresh perspectives on how to achieve extremely sensitive electrochemical detection in the area of food safety.

Graphene and Perovskite-Based Nanocomposite for Both Electrochemical and Gas Sensor Applications: An Overview

Perovskite and graphene-based nanocomposites have attracted much attention and been proven as promising candidates for both gas (H₂S and NH₃) and electrochemical (H₂O₂, CH₃OH and glucose) sensor applications. In this review, the development of portable sensor devices on the sensitivity, selectivity, cost effectiveness, and electrode stability of chemical and electrochemical applications is summarized. The authors are mainly focused on the common analytes in gas sensors such as hydrogen sulfide, ammonia, and electrochemical sensors including non-enzymatic glucose, hydrazine, dopamine, and hydrogen peroxide. Finally, the article also addressed the stability of composite performance and outlined recent strategies for future sensor perspectives.

Crystalline Cobalt/Amorphous LaCoOx Hybrid Nanoparticles Embedded in Porous Nitrogen-Doped Carbon as Efficient Electrocatalysts for Hydrazine-Assisted Hydrogen Production

Hydrazine electro-oxidation has received substantial attention owing to its high energy density, low onset potential, and wide applications in hydrazine-assisted hydrogen production and direct hydrazine fuel cells. In this work, crystalline cobalt/amorphous LaCoO_x hybrid nanoparticles embedded in porous nitrogen-doped carbon (N-C) were fabricated via pyrolytic decomposition of the dual-metal lanthanum-incorporated zeolitic imidazolate framework (La/ZIF-67), which exhibit high activity and stability toward the electrocatalytic hydrazine oxidation reaction (HzOR). The hybrid nanoparticles based on metallic cobalt and amorphous LaCoO_x could provide abundant active sites for HzOR catalysis, while the highly conductive and porous N-C could act as both robust skeleton for anchoring the active hybrid nanoparticles and facile charge transport pathway for the HzOR process, thereby resulting in enhanced HzOR activity. With the synergistic merits of enriched active sites, a large surface area, enhanced charge-transfer ability, and intimate catalyst anchoring, promoted HzOR performance with high activity and stability was achieved for the optimized catalyst, which shows an ultralow onset potential of -0.17 V versus reversible hydrogen electrode (RHE), high HzOR current density of 69.2 mA cm^-2 at 0.3 V versus RHE, and superior stability for 20 h continuous catalysis, making the catalyst a promising electrode material for hydrazine-assisted hydrogen production.