Photoelectrochemical properties of “increasingly dark” TiO2 nanotube arrays

Photoactivity of amorphous and crystalline TiO2 nanotube arrays (TNA) films in gas phase CO2 reduction to methane with simultaneous H2 production

This study assessed the photoactivity of amorphous and crystalline TiO2 nanotube arrays (TNA) films in gas phase CO2 reduction. The TNA photocatalysts were fabricated by titanium anodization and submitted to an annealing treatment for crystallization and/or cathodic reduction to introduce Ti3+ and oxygen vacancies into the TiO2 structure. The cathodic reduction demonstrated a significant effect on the generated photocurrent. The photoactivity of the four TNA catalysts in CO2 reduction with water vapor was evaluated under UV irradiation for 3 h, where CH4 and H2 were detected as products. The annealed sample exhibited the best performance towards methane with a production rate of 78 μmol gcat-1 h-1, followed by the amorphous film, which also exhibited an impressive formation rate of 64 μmol gcat-1 h-1. The amorphous and reduced-amorphous films exhibited outstanding photoactivity regarding H2 production (142 and 144 μmol gcat-1 h-1, respectively). The annealed catalyst also revealed a good performance for H2 production (132 μmol gcat-1 h-1) and high stability up to five reaction cycles. Molecular dynamic simulations demonstrated the changes in the band structure by introducing oxygen vacancies. The topics covered in this study contribute to the Sustainable Development Goals (SDG), involving affordable and clean energy (SDG#7) and industry, innovation, and infrastructure (SDG#9).

The Impact of Side-Selective Laser Tailoring of Titania Nanotubes on Changes in Photoelectrocatalytic Activity

Over the last few decades, titanium(IV) oxide-based materials have gained particular attention due to their stability, corrosion resistance, photocatalytic activity under UV light, and possibilities for modification. Among various structures, TiO₂ nanotubes (NTs) grown on Ti foil or glass substrates and obtained through a simple anodization process are widely used as photocatalysts or photoanodes. During the anodization process, the geometry of the nanotubes (length, distribution, diameter, wall thickness, etc.) is easily controlled, though the obtained samples are amorphous. Heat treatment is required to transform the amorphous material into crystalline material. However, instead of time- and cost-consuming furnace treatment, fast and precise laser annealing is applied as a promising alternative. Nonetheless, laser treatment can result in geometry changes of TiO₂ NTs, consequently altering, their electrochemical activity. Moreover, modification of the TiO₂ NTs surfaces with transition metals and further laser treatment can result in materials with unique photoelectrochemical properties. In this regard, we gathered the latest achievements in the field of laser-treated titania for this review paper. We mainly focused on single structural and morphological changes resulting from pulsed laser annealing and their influence on the electrochemical properties of titania. Finally, the theoretical basis for and combination of laser- and metal-modifications and their impact on the resulting possibilities for electrochemical water splitting are also discussed.

Galvanic Deposition of Pt Nanoparticles on Black TiO2 Nanotubes for Hydrogen Evolving Cathodes

A galvanic deposition method for the in-situ formation of Pt nanoparticles (NPs) on top and inner surfaces of high-aspect-ratio black TiO₂ -nanotube electrodes (bTNTs) for true utilization of their total surface area has been developed. Density functional theory calculations indicated that the deposition of Pt NPs was favored on bTNTs with a preferred [004] orientation and a deposition mechanism occurring via oxygen vacancies, where electrons were localized. High-resolution transmission electron microscopy images revealed a graded deposition of Pt NPs with an average diameter of around 2.5 nm along the complete nanotube axis (length/pore diameter of 130 : 1). Hydrogen evolution reaction (HER) studies in acidic electrolytes showed comparable results to bulk Pt (per geometric area) and Pt/C commercial catalysts (per mg of Pt). The presented novel HER cathodes of minimal engineering and low noble metal loadings (μg cm^-2 range) achieved low Tafel slopes (30-34 mV dec^-1 ) and high stability in acidic conditions. This study provides important insights for the in-situ formation and deposition of NPs in high-aspect-ratio structures for energy applications.

Titanium industrial residues surface modification towards its reuse as antimicrobial surfaces

In this study, a new material obtained from titanium ingots residue was coated with natural carotenoids having antibacterial properties. The waste is a no recycling titanium scrap from technological production process which was pressed and transformed into disks titanium samples. Through anodization and annealing procedures of the titanium disk, a nanostructured titanium dioxide surface with photocatalytic and antibacterial properties was successfully obtained. The titanium scrap impurities (V, Al, and N), unwanted for production process, have shown to improve electrochemical and semiconductor properties of the residue surfaces. The nanostructured titanium scrap surface was modified with two different carotenoids, torularhodin and β-carotene, to potentiate the antibacterial properties. The bactericidal tests were performed against Salmonella typhimurium and Escherichia coli, both Gram-negative. The best bactericidal effect is obtained for nanostructured titanium scrap disks immersed in torularhodin, with a percentage of growth inhibition around 60% against both tested bacteria. The results suggest that this low-cost waste material is suitable for efficient reuse as antibacterial surface after a few simple and inexpensive treatments.