Examination of gas and solid products during the preparation of activated carbon using phosphoric acid

Advanced Material-oriented Biomass Precise Reconstruction: A Review on Porous Carbon with Inherited Natural Structure and Created Artificial Structure by Post-treatment

Manufacturing of porous carbon with biomass resources has been intensively investigated in recent decades. The diversity of biomass species and great variety of processing methods enable the structural richness of porous carbon as well as their wide applications. In this review, we specifically focused on the structure of biomass-derived porous carbon either inherited from natural biomass or created by post-treatment. The intrinsic structure of plant biomass was briefly introduced and the utilization of the unique structures at different length-scales were discussed. In term of post-treatment, the structural features of activated carbon by traditional physical and chemical activation were summarized and compared in a wide spectrum of biomass species, statistical analysis were performed to evaluate the effectiveness of different activation methods in creating specific pore structures. The similar pore structure of biomass-derived carbon and coal-derived carbon suggested a promising replacement with more sustainable biomass resources in producing porous carbon. In summary, using biomass as porous carbon precursor endows the flexibility of using its naturally patterned micro-structure and the tunability of controlled pore-creation by post treatment. This article is protected by copyright. All rights reserved.

Sago cycas-based hierarchical-structured porous carbon for adsorption of acetone vapour: preparation, characterization and performance

The porous structure and oxygen-containing functional groups of carbon materials play important roles in the adsorption of volatile organic compounds (VOCs). In this study, hierarchical-structured porous carbons (HSPCs) with a large specific surface area and abundant oxygen-containing functional groups were prepared from sago cycas without a template or post-processing for acetone (one of the most common VOCs) adsorption. The micropore volume (0.41-1.15 cm³ g^-1) and oxygen-containing functional groups (0.3-1.92 mmol g^-1) of HSPCs were manipulated by adjusting the activation temperature. Static adsorption data showed that the HSPC activated at 600 °C (HSPC-600) was superior for acetone adsorption, and a maximum adsorption capacity of 3.75 mmol g^-1 was achieved at 25 °C and 0.1 kPa. Breakthrough curves and cyclic adsorption-desorption tests demonstrated the dynamic adsorption capacity and regeneration performance of HSPC-600 were excellent as well. The adsorption isotherms were well described by Langmuir and Langmuir-Freundlich models, indicating the adsorption of acetone on HSPCs is a monolayer adsorption process. Due to electrostatic interaction, hydrogen bond and van der Waals forces between acetone molecules and oxygen-containing functional groups, the adsorption capacity of HSPCs for acetone was significantly improved at low relative pressure. This study may provide a peculiar insight into the development of high-performance acetone adsorbent.

Effect of Process Parameters on the Microstructure and Performance of TiO2-Loaded Activated Carbon

In this study, the visible-light-driven photocatalytic regeneration performance of TiO2-loaded activated carbon (TiO2/AC) was effectively improved. By carefully controlling the activation condition at 700 °C for 2 h with a 60% H3PO4 concentration and 3:1 TBT (tetrabutyl titanate) impregnation ratio, 90.5% of methylene blue (50 mg/L) was removed within 2 h by a low-dose TiO2/AC (0.5 g/L), which was much higher than those obtained in previous studies on TiO2/AC. Moreover, the effects of process variables on the microstructure and performance of TiO2/AC were systematically investigated. The results showed that (1) the long period of activation time effectively inhibited the photogenerated charge carrier recombination and enhanced the regeneration performance of samples; (2) the photogenerated charge carrier recombination rate was lowered initially and then increased as the temperature ascended, whereas the pore volume showed an opposite variation tendency, and thus the adsorption and regeneration performances of samples were improved at 500-700 °C and then weakened at 800 °C; (3) the increase of H3PO4 concentration effectively inhibited the charge carrier recombination and had an improvement in the adsorption and regeneration performances of samples; and (4) the photogenerated charge carrier recombination rate and bandgap value of samples decreased initially and then increased with increasing TBT mass ratio, so the regeneration performances of samples were improved initially and then lowered.

Effective Removal of Pb(II) Ions by Electrospun PAN/Sago Lignin-based Activated Carbon Nanofibers

Heavy metal pollution, such as lead, can cause contamination of water resources and harm human life. Many techniques have been explored and utilized to overcome this problem, with adsorption technology being the most common strategies for water treatment. In this study, carbon nanofibers, polyacrylonitrile (PAN)/sago lignin (SL) carbon nanofibers (PAN/SL CNF) and PAN/SL activated carbon nanofibers (PAN/SL ACNF), with a diameter approximately 300 nm, were produced by electrospinning blends of polyacrylonitrile and sago lignin followed by thermal and acid treatments and used as adsorbents for the removal of Pb(II) ions from aqueous solutions. The incorporation of biodegradable and renewable SL in PAN/SL blends fibers produces the CNF with a smaller diameter than PAN only but preserves the structure of CNF. The adsorption of Pb(II) ions on PAN/SL ACNF was three times higher than that of PAN/SL CNF. The enhanced removal was due to the nitric acid treatment that resulted in the formation of surface oxygenated functional groups that promoted the Pb(II) ions adsorption. The best-suited adsorption conditions that gave the highest percentage removal of 67%, with an adsorption capacity of 524 mg/g, were 40 mg of adsorbent dosage, 125 ppm of Pb(II) solution, pH 5, and a contact time of 240 min. The adsorption data fitted the Langmuir isotherm and the pseudo-second-order kinetic models, indicating that the adsorption is a monolayer, and is governed by the availability of the adsorption sites. With the adsorption capacity of 588 mg/g, determined via the Langmuir isotherm model, the study demonstrated the potential of PAN/SL ACNFs as the adsorbent for the removal of Pb(II) ions from aqueous solution.