Removal of phosphate from aqueous solution using MgO-modified magnetic biochar derived from anaerobic digestion residue

Metal-doped biochar for selective recovery and reuse of phosphate from water: Modification design, removal mechanism, and reutilization strategy

Phosphorus (P) plays a crucial role in plant growth, which can provide nutrients for plants. Nonetheless, excessive phosphate can cause eutrophication of water, deterioration of aquatic environment, and even harm for human health. Therefore, adopting feasible adsorption technology to remove phosphate from water is necessary. Biochar (BC) has received wide attention for its low cost and environment-friendly properties. However, undeveloped pore structure and limited surface groups of primary BC result in poor uptake performance. Consequently, this work introduced the synthesis of pristine BC, parameters influencing phosphate removal, and corresponding mechanisms. Moreover, multifarious metal-doped BCs were summarized with related design principles. Meanwhile, mechanisms of selective phosphate adsorption by metal-doped BC were investigated deeply, and the recovery of phosphate from water, and the utilization of phosphate-loaded adsorbents in soil were critically presented. Finally, challenges and prospects for widespread applications of selective phosphate adsorption were proposed in the future.

Synthesis of a novel magnetic calcium-rich biochar nanocomposite for efficient removal of phosphate from aqueous solution

Phosphorus (P) scarcity and eutrophication have triggered the development of new materials for P recovery. In this work, a novel magnetic calcium-rich biochar nanocomposite (MCRB) was prepared through co-precipitation of crab shell derived biochar, Fe2+ and Fe3+. Characteristics of the material demonstrated that the MCRB was rich in calcite and that the Fe3O4 NPs with a diameter range of 18-22 nanometers were uniformly adhered on the biochar surface by strong ether linking (C-O-Fe). Batch tests demonstrated that the removal of P was pH dependent with an optimal pH of 3-7. The MCRB exhibited a superior P removal performance, with a maximum removal capacity of 105.6 mg g-1, which was even higher than the majority lanthanum containing compounds. Study of the removal mechanisms revealed that the P removal by MCRB involved the formation of hydroxyapatite (HAP-Ca5(PO4)3OH), electrostatic attraction and ligand exchange. The recyclability test demonstrated that a certain level (approximately 60%) was still maintained even after the six adsorption-desorption process, suggesting that MCRB is a promising material for P removal from wastewater.

Synthesis, characterization, and phosphorus adsorption of Mg/Fe-modified biochar from cotton stalk pretreated with Coriolus versicolor

In recent years, the research potential in utilizing biochars as adsorbents in adsorption processes has grown due to their eco-friendly and economical nature. However, biochar often possesses a negative surface charge that limits its affinity for binding anions. Nitric acid washing and pretreatment with Coriolus versicolor can break down the lignocellulosic structure in cotton stalk waste, facilitating the subsequent impregnation of Mg and Fe metal oxides. These pretreatment steps can lead to the production of diverse and functionalized biochars with higher adsorption capacities. In this study, cotton stalk waste was first washed with diluted nitric acid and then subjected to biological pretreatment by incubation with C. versicolor, followed by impregnation with Mg and Fe to obtain CV-CS/Fe and CV-CS/Mg biochars. The results showed that the applied pretreatments altered the physicochemical properties and significantly increased the phosphorus adsorption capacity. The adsorption capacities of CV-CS/Fe and CV-CS/Mg biochars were found to be 277.88 and 507.01 mg g-1, respectively. The results indicate that the incorporation of multiple metal oxide impregnates enhances P adsorption. Furthermore, in the kinetic study, pseudo-first-order and pseudo-second-order models provided a well fit, determining chemical adsorption as the main adsorption mechanism for phosphorus adsorption. The biochars demonstrated compatibility with Langmuir-Freundlich models. Overall, the findings suggest the possibility of synthesizing biochars with improved adsorptive properties through pretreatment, and these engineered biochars hold promising potential as effective adsorbents in the field. PRACTITIONER POINTS: Eco-friendly, natural, and economical biochar was synthesized. Biochar was produced via Coriolus versicolor pretreatment. High adsorption capacities of CV-PS/Mg biochars were found to be 507.01 mg g-1. Adsorption capacities of biochars can be improved by pretreatment.

Desalination RO reject brine as a novel-based porous geopolymer for phosphorus removal from contaminated media

Desalination reverse osmosis reject brine-based porous geopolymer (RO/GP) was produced and investigated as an improved adsorbent for phosphorus (P) removal from tainted seawater, brackish water, river water, and municipal wastewater effluent. The RO reject brine/geopolymer was produced by reacting metakaolin and fly ash with a Na-alkali activator and anhydrous RO brine as a sacrificial template. The influence of RO reject brine content on water absorption, porosity, mechanical, and structural properties were examined. The developed RO-based geopolymers exhibited the greatest porosity (58.3-84.2 % vol%), a significant ratio of open porosity to total porosity (67.7-92.1 %), and outstanding compression strength (3.6-10.4 MPa). The produced RO/GP structure has an adsorption capacity of 92.4 mg-P/g. The sequestration reaction of phosphorus by RO/GP is of pseudo-second-order kinetic behavior via Chi-squared (χ2), RMSE, and determination coefficient (R2) values. Regarding their agreement with Langmuir behavior, the phosphorus adsorption uptakes occur in homogeneous and monolayer states. The reaction is exothermic, spontaneous, and favorable. The RO/GP exhibits significant affinity for phosphorus co-existing with Cl-, Na+, SO42-, K+, HCO3-, and Ca2+. The RO/GP shows high safety during the adsorption investigation, with a total cost of 0.32 $/kg-P.

Efficient removal of phosphorus and nitrogen from aquatic environment using sepiolite-MgO nanocomposites: preparation, characterization, removal performance, and mechanism

Excessive phosphorus will lead to eutrophication in aquatic environment; the efficient removal of phosphorus is crucial for wastewater engineering and surface water management. This study aimed to fabricate a nanorod-like sepiolite-supported MgO (S-MgO) nanocomposite with high specific surface area for efficient phosphate removal using a facile microwave-assisted method and calcining processes. The impact of solution pH, adsorbent dosage, contact time, initial phosphate concentrations, Ca2+ addition, and N/P ratio on the phosphate removal was extensively examined by the batch experiments. The findings demonstrated that the S-MgO nanocomposite exhibited effective removal performance for low-level phosphate (0 ~ 2.0 mM) within the pH range of 3.0 ~ 10.0. Additionally, the nanocomposite can synchronously remove phosphate and ammonium in high-level nutrient conditions (> 2.0 mM), with the maximum removal capacities of 188.49 mg P/g and 89.78 mg N/g. Quantitative and qualitative analyses confirmed the successful harvesting of struvite in effluent with high-phosphate concentrations, with the mechanisms involved attributed to a synergistic combination of sorption and struvite crystallization. Due to its proficient phosphate removal efficiency, cost-effectiveness, and substantial removal capacity, the developed S-MgO nanocomposite exhibits promising potential for application in phosphorus removal from aquatic environments.

A comprehensive review on the preparation of biochar from digestate sources and its application in environmental pollution remediation

The preparation of biochar from digestate is one of the effective ways to achieve the safe disposal and resource utilization of digestate. Nevertheless, up to now, a comprehensive review encompassing the factors influencing anaerobic digestate-derived biochar production and its applications is scarce in the literature. Therefore, to fill this gap, the present work first outlined the research hotspots of digestate in the last decade using bibliometric statistical analysis with the help of VOSviewer. Then, the characteristics of the different sources of digestate were summarized. Furthermore, the influencing factors of biochar preparation from digestate and the modification methods of digestate-derived biochar and associated mechanisms were analyzed. Notably, a comprehensive synthesis of anaerobic digestate-derived biochar applications is provided, encompassing enhanced anaerobic digestion, heavy metal remediation, aerobic composting, antibiotic/antibiotic resistance gene removal, and phosphorus recovery from digestate liquor. The economic and environmental impacts of digestate-derived biochar were also analyzed. Finally, the development prospect and challenges of using biochar from digestate to combat environmental pollution are foreseen. The aim is to not only address digestate management challenges at the source but also offer a novel path for the resourceful utilization of digestate.

Biochar-supported magnesium oxide as high-efficient lead adsorbent with economical use of magnesium precursor

With unique porous structure inherited from lignocellulose, biochar was an appropriate carrier for small-size MgO materials, which could simplify the synthetic process and better solve agglomeration and separation problems during adsorption. Biochar-supported MgO was prepared with impregnation method. Under different synthesis conditions, the obtained MgO presented diverse properties, and moderate pyrolysis condition was conducive to the improvement of Mg conversion rate. The Pb(II) capacity was highly correlated with Mg content, rather than the specific surface area. Reducing the pyrolysis temperature or increasing the usage of supporter could improve adsorption efficiency when using Mg content-normalized capacity as the criterion. The better release ability of Mg, contribute by the higher extent of hydration and better spread of MgO, were the critical factors. The maximal Mg content-normalized capacity could reach 0.932 mmol·mmol-Mg^-1 with the mass ratio of biochar/MgCl₂·6H₂O = 4:1 at the pyrolysis temperature of 600 °C. Considering the ultimate utilization efficiency of Mg in precursor, the optimum Mg consumption-normalized capacity was 0.744 mmol·mmol-Mg^-1 with the mass ratio of biochar/MgCl₂·6H₂O = 1:1 at 600 °C.

Porous MgO-modified biochar adsorbents fabricated by the activation of Mg(NO3)2 for phosphate removal: Synergistic enhancement of porosity and active sites

Engineering magnesium oxide (MgO)-modified biochar (MgO-biochar) with high porosity and active MgO load is a feasible pathway to enhance phosphate adsorption capacity. However, the blockage to pores caused by MgO particles is ubiquitous during the preparation, which seriously impaired the enhancement in adsorption performance. In this research, with the intent to enhance phosphate adsorption, an in-situ activation method based on Mg(NO₃)₂-activated pyrolysis technology was developed to fabricate MgO-biochar adsorbents with abundant fine pores and active sites simultaneously. The SEM image revealed that the tailor-made adsorbent has well-developed porous structure and abundant fluffy MgO active sites. Its maximum phosphate adsorption capacity was coming up to 1809 mg/g. The phosphate adsorption isotherms are in accordance well with the Langmuir model. The kinetic data, which agreed with the pseudo-second-order model, indicated that chemical interaction is existing between phosphate and MgO active sites. This work verified that the phosphate adsorption mechanism on MgO-biochar was composed of protonation, electrostatic attraction, monodentate complexation and bidentate complexation. In general, the facile in-situ activation method using Mg(NO₃)₂ pyrolysis illuminated biochar activation with fine pores and highly efficient adsorption sites for efficient wastewater treatment.

Novel oxymagnesite/green rust nanohybrids for selective removal and slow release of phosphate in water

The new paradigm in wastewater treatment demands to change traditional pollutants removal into resource recovery, especially for non-renewable P resources, effectively recovering phosphate from wastewater and reutilizing it as a nutrient is crucial to P sustainable utilization and P-related pollution control. The nanomaterial-based adsorption technology for P recovery from wastewater is becoming a research hotspot due to its high efficiency and selectivity. Herein, to recover aqueous phosphate, we developed novel oxymagnesite/green rust (OMGR) nanohybrids by a one-pot hydrothermal method. Green rust nanoparticles dispersed on the highly reactive oxymagnesite (MgO2MgCO₃) nanosheets could achieve efficient recovery and reuse of P. The volume ratio of water to ethylene glycol played an important role in the preparation of OMGR. The OMGR possessed an excellent selectivity of phosphate removal in the presence of multi-anions and wide pH adaptability in 4.0-10.0. The formation of MgP nanocrystals and the inner-sphere FeOP complexes via ligand exchange contributed to the selective removal of P by OMGR, and the removal capacity reached 141 mg P^.g^-1. The process of phosphate removal by OMGR was spontaneously endothermic and controlled by the intraparticle and boundary layer diffusion. Most importantly, the high bioavailable P (127 mg^.g^-1) of P-loaded OMGR had a persistent release behavior regulated by dissolution and diffusion, indicating that the P-loaded OMGR can act as a slow-release P-fertilizer. The findings provide a green and eco-friendly approach to realizing P resource recovery and reuse for phosphate-containing wastewaters.

Converting Chrysotile Nanotubes into Magnesium Oxide and Hydroxide Using Lanthanum Oxycarbonate Hybridization and Alkaline Treatment for Efficient Phosphate Adsorption

Magnesium oxide and hydroxide nanomaterials comprise a class of promising advanced functional metal nanomaterials whose use in environmental and material applications is increasing. Several strategies to synthesize these nanomaterials have been described but are unsustainable and uneconomic. This work reports on a processing strategy that turns natural magnesium-rich chrysotile into magnesium oxide and hydroxide nanoparticles via nanoparticle hybridization and an alkaline process while enabling La-based nanoparticles to coat the chrysotile nanotube surfaces. The adsorbent's resulting hybrid nanostructure had an outstanding capacity for phosphate uptake (135.2 mg P g^-1) and enhanced regeneration performance. Furthermore, the adsorbent featured wide applicability with respect to the coexistence of competitive anions and a broad range of pH conditions, and its high-performance phosphate removal from sewage effluent was also demonstrated. Spectroscopic and microscopic analyses revealed the scavenging ability of phosphate by the La-based and Mg-based nanoparticles and the multiple capture mechanisms involved, including surface complexation and ion exchange. This proposed approach expands chrysotile's potential use as a magnesium-rich nanomaterial and harbors great promise for the removal of pollutants in a variety of real-world settings.

Preparation, adsorption performance and mechanism of MgO-loaded biochar in wastewater treatment: A review

Biochar is a low cost, porous and solid material with an extremely high carbon content, various types of functional groups, a large specific surface area and many other desirable characteristics. Thus, it is often used as an adsorbent or a loading matrix. Nano-magnesium oxide is a crystalline material with small particles and strong ion exchangeability. However, due to the high surface chemical energy, it easily forms agglomerates of particles. Therefore, to combine the advantages of biochar and magnesium, metal magnesium nanoparticles can be loaded onto the surface of biochar with different modification techniques, resulting in biochars with low cost and high adsorption performance to be used as an adsorption matrix (collectively referred to as Mg@BC). This review presents the effects of different Mg@BC preparation methods and synthesis conditions and summarizes the removal capabilities and adsorption mechanisms of Mg@BC for different types of pollutants in water. In addition, the review proposes the prospects for the development of Mg@BC to solve various problems in the future.

Environmental application of engineering magnesite slag for phosphate adsorption from wastewater

Herein, magnesite slags (MS), which remain after sulfuric acid extraction from light burnt magnesite in the magnesite industry, were used as phosphate adsorbents in wastewater. The MS were calcined under 700 °C to enhance phosphate adsorption. The calcined magnesite slags (CMS) were characterized by nitrogen adsorption-desorption isotherm, X-ray diffraction, and scanning electron microscopy. A series of batch adsorption experiments were carried out to test the phosphate adsorption capacity of CMS. The results showed that the calcific treatment promoted the conversion from Mg, Ca, Fe, etc. compound to metal oxide of the MS. The generated metal oxide particles resulted in 237.4 mg/g increase in the phosphate adsorption capacity. The phosphate adsorption isotherm of CMS fitted the Langmuir model better, and the maximum adsorption capacity of CMS was 526 mg/g. The adsorption kinetics of phosphate on CMS can be described by the pseudo-second-order model. The phosphate removal efficiency was greater than 98% in 300 mg/L phosphate solution. Mechanism investigation results indicated that phosphate was adsorbed by CMS through MgO protonation, electrostatic attraction, Mg-P complexation, and ligand exchange. The results obtained in this work demonstrate that the CMS is a potential effective adsorbent for removal and reutilization phosphate from P-contaminated water, due to it can be employed as a fertilizer after phosphate adsorption.

Insight into the Impacts and Removal Pathways of Perfluorooctanoic Acid (PFOA) in Anaerobic Digestion

Perfluorooctanoic acid (PFOA) that accumulates in wastewater and excess sludge interact with the anaerobes and deteriorate the energy recovery and pollutants removal performance in the anaerobic digestion (AD) system. However, the interaction between PFOA and microbial metabolism in the AD systems remains unclear. This study aimed to clarify the effects and mechanism of PFOA on the AD process as well as the removal pathways of PFOA in an AD system. The results showed that the methane recovery efficiency was inhibited by 7.6–19.7% with the increased PFOA concentration of 0.5–3.0 mg/L, and the specific methanogenesis activity (SMA) was inhibited by 8.6–22.3%. The electron transfer system (ETS) was inhibited by 22.1–37.3% in the PFOA-containing groups. However, extracellular polymeric substance (EPS) gradually increased due to the toxicity of PFOA, and the ratio of protein to polysaccharide shows an upward trend, which led to the formation of sludge aggregates and resistance to the toxic of PFOA. The PFOA mass balance analysis indicated that 64.2–71.6% of PFOA was removed in the AD system, and sludge adsorption was the main removal pathway, accounting for 36.1–61.2% of the removed PFOA. In addition, the anaerobes are proposed to have the potential to reduce PFOA through biochemical degradation since 10.4–28.2% of PFOA was missing in the AD system. This study provides a significant reference for the treatment of high-strength PFOA-containing wastes.

Solvent-Free Synthesis of MgO-Modified Biochars for Phosphorus Removal from Wastewater

Adsorption is an efficient technology for removing phosphorus from wastewater to control eutrophication. In this work, MgO-modified biochars were synthesized by a solvent-free ball milling method and used to remove phosphorus. The MgO-modified biochars had specific surface areas 20.50–212.65 m² g⁻¹ and pore volume 0.024–0.567 cm³ g⁻¹. The as-prepared 2MgO/BC-450-0.5 had phosphorus adsorption capacities of 171.54 mg g⁻¹ at 25 °C and could remove 100% of phosphorus from livestock wastewater containing 39.51 mg L⁻¹ phosphorus. The kinetic and isotherms studied show that the pseudo-second-order model (R² = 0.999) and Langmuir models (R² = 0.982) could describe the adoption process well. The thermodynamic analysis indicated that the adsorption of phosphorus on the MgO-modified biochars adsorbent was spontaneous and endothermic. The effect of pH, FTIR spectra and XPS spectra studies indicated that the phosphorus adsorption includes a protonation process, electrostatic attraction and precipitation process. This study provides a new strategy for biochar modification via a facile mechanochemical method.

Feasible synthesis of a novel and low-cost seawater-modified biochar and its potential application in phosphate removal/recovery from wastewater

In this study, a novel and low-cost seawater-modified biochar (SBC) was fabricated via the pyrolysis of fir wood waste followed by co-precipitation modification using seawater as the Ca/Mg source. The co-precipitation pH was a vital factor during modification, and the optimal pH was 10.50 according to calculations using PHREEQC 2.5 and experiments. The characterizations indicated that Ca and Mg were loaded on the SBC as irregular CaCO₃ and nanoflake-like Mg(OH)₂, respectively, with the latter dominating. The SBC exhibited a high maximum adsorption capacity of 181.07 mg/g for phosphate, calculated using the Langmuir model, excellent adsorption performance under acidic and neutral conditions (pH = 3.00-7.00), and remarkable selectivity against Cl^-, NO₃^-, and SO₄^2-. The presence of HCO₃^- promoted adsorption. The mechanisms behind phosphate adsorption involved electrostatic attraction, ligand exchange, precipitation, and inner-sphere complexation. Mg, rather than Ca, was served as the main adsorptive sites for phosphate. Additionally, the feasibility of treating real-world wastewater was tested in batch (using SBC powders) and fixed-bed column (using SBC granules) experiments. The results indicate that the SBC powders could reduce the phosphate concentration from 1.26 mg P/L to below 0.5 mg P/L at a low dose of 0.50 g/L, and the SBC granules exhibited a high removal efficiency with excellent recyclability; the capacity still remained at 78.92% of the initial capacity after five adsorption-desorption runs. Furthermore, the modification process almost did not increase the production cost of the SBC, which was estimated to be 0.41 $/kg. Our results demonstrate that seawater is a low-cost and efficient modifier for biochar modification, and the resultant SBC demonstrates great potential for treating actual phosphate-containing wastewater.

Biomass as source for hydrochar and biochar production to recover phosphates from wastewater: A review on challenges, commercialization, and future perspectives

Excessive phosphate run-off with total phosphorus concentration greater than 20 μg P L^-1 triggers the growth of harmful algal species in waterbodies and potentially leads to eutrophication. This has severe negative implications on aquatic environment and impacts human health. The annual economic impact of harmful algal blooms is reported to be as high as $25 million for public health and commercial fishery sector, $29 million for recreation/tourism sector and $2 million for monitoring and management. Adsorption is widely considered as an effective and economic strategy to achieve extremely low concentration of phosphorus. The char produced by valorizing various waste biomasses have been gaining attention in phosphorus remediation owing to their availability, their ability to regenerate and reuse. This review paper exclusively focuses on utilizing hydrochar and biochar synthesized from waste biomass, respectively, through hydrothermal carbonization and slow pyrolysis to mitigate phosphorus concentration and potential strategies for handling the spent char. The key mechanisms involved in phosphate adsorption are electrostatic interaction, ion exchange and complexation. The maximum adsorption capacity of hydrochar and biochar ranges from 14-386 mg g^-1 and 3-887 mg g^-1, respectively. Hydrochar and biochar are cost-effective alternative to commercial activated carbon and spent char can be used for multiple adsorption cycles. Furthermore, extensive research studies on optimizing the feedstock, reaction and activation conditions coupled with technoeconomic analysis and life cycle assessment could pave way for commercialization of char-based adsorption technology.

Biochar application in organics and ultra-violet quenching substances removal from sludge dewatering leachate for algae production

Algae production in nutrient rich sludge dewatering leachate after biogas production is a promising option for wastewater treatment plants. However, the ultra-violet (UV) absorbing characteristic of UV-quenching substances (UVQS) existing in these waters can notably reduce the light transmission within the liquid body. The present work demonstrates a comparative adsorptive removal of UVQS, and other organic substances (expressed as COD and TOC) onto the "acid catalyst" functionalised adsorbent (PPhA) and commercial activated carbon (CAC) from leachate originating from leftover sludge dewatering after biogas production. Laboratory scale column studies were performed to investigate the adsorption performance of selected parameters. The PPhA increased the UV transmittance of leachate more than 4 times and outperformed CAC. Bed Depth Service Time and Yan models were used on the experimental data in order to estimate the maximum adsorption capacity and evaluate the characteristics of the fixed-bed. The PPhA equilibrium uptake of COD and TOC amounted to 5.7 mg/g and 0.9 mg/g, respectively. The postulated removal mechanism in environmentally relevant conditions (e.g., pH neutral) suggested a complex interaction between the biochar and organic macromolecules. Diluted phosphoric acid solution (0.01 mol/L) was successfully used for the column regeneration. Beside the UVQS, PPhA showed affinity towards toxic heavy metals (e.g., Pb, Ni, Co) pointing out the rich surface chemistry of the PPhA. Based on the obtained results and successfully implemented scale-up methodology, the low-cost PPhA adsorbent might effectively compete with the CAC as a highly efficient platform in wastewaters leachate processing.

Engineered biochars for recovering phosphate and ammonium from wastewater: A review

Biochar has gained great scientific attention as a promising agent for agricultural and environmental applications. A variety of biochars with excellent properties such as high porosity, surface area and functional groups have been developed for nutrients recovery from wastewater. Compared to pristine biochar, engineered biochar with enlarged surface area and abundant functional groups has been prepared which shows a new type of carbon-based material with enhanced adsorption potential for nutrients in wastewater. To date, a few reviews have been specifically focused on several important aspects of engineered biochar, such as its application to recover phosphate and ammonium from wastewater and subsequent use as a slow-release fertilizer. In this work, novel modification/treatment methods including activation with acid/alkali, functionalization with amides, thiols and oxidizing agents, metal salt impregnation, loading with various minerals and carbon-based materials are reviewed for preparing engineered biochar with improved adsorption capacity. Various sources of biomass for producing biochars were estimated, and the intrinsic characteristics and potential of biochar products for simultaneous recovery/removal of phosphate and ammonium from wastewater were evaluated. Relevant interaction mechanisms of phosphate and ammonium adsorption on engineered biochars have been discussed in details. Finally, important future prospects as well as industrial/commercial-scale application of engineered biochars for phosphate and ammonium recovery from wastewater have been emphasized. We believe that this review will provide broad scientific opportunities for thorough understanding of applying engineered biochar as a low-cost and environmentally sustainable material for nutrients recovery from wastewater.

Preparation of magnetic biochar and its application in catalytic degradation of organic pollutants: A review

In recent years, magnetic biochar (MBC) has been greatly concerned because of its magnetic separation characteristics, and has been successfully used as a catalyst in the catalytic degradation of organic pollutants. However, there is currently a lack of a more systematic summary of MBC preparation methods, and no detailed overview of the catalytic mechanism of MBC catalysts for the degradation of organic pollutants. Therefore, we carry out this work to fill the above gaps. At first, we summarize the raw materials, preparation methods, and types of MBC in detail, and emphasize the MBC prepared by iron-containing sludge. Then, the catalytic mechanisms of MBC in peroxydisulfate, peroxymonosulfate, Fenton-like, photocatalysis, and NaBH₄ systems are carefully summarized, highlighting the contribution of various parts of MBC in catalysis. The degradation efficiency of organic pollutants in the above systems is evaluated. Finally, the stability and reusability of MBC catalysts are evaluated. In conclusion, this review contributes a meager force to the future development of MBC.

Enhanced removal of phosphate from aqueous solution using Mg/Fe modified biochar derived from excess activated sludge: removal mechanism and environmental risk

In this study, Mg-modified sludge biochar (MB) and Mg-Fe double oxides/sludge biochar composites (MFB) were synthesized for enhanced removal of phosphate from aqueous solution. The phosphate adsorption followed the Langmuir-Freundlich isotherm model, and the maximum capacity was 142.31 mg P/g and 35.41 mg P/g for MB and MFB, respectively. MB exhibited the higher adsorption capacity at pH 8-9 and performed well under the influences of coexisting anions and temperature (4-45 °C). Adsorption kinetics was well described by the pseudo-second-order kinetic model, indicating the chemical bonding between phosphate and adsorption sites. The adsorption capacity of phosphate decreased by < 15% after three successive recycles. Based on FTIR, XRD, and XPS analysis, the main mechanisms for phosphate removal by MB included electrostatic attraction, surface complexation, and precipitation. Hydroxides/oxides particles of Mg on the surface of MB with positive charge could adsorb HPO₄^2- and PO₄^3- to form surface complex and convert to MgHPO₄ and Mg₃(PO₄)₂. The released amounts of Fe, Cd, Cr, Pb, Cu, Zn, Sb, and As from MB and MFB were low and acceptable. However, the released amount of Mg was as high as 4.9 wt% for MB and 8.7 wt% for MFB at the pH corresponding maximum adsorption capacity, posing a risk of salt increase. The grass (Lolium perenne L.) germination and early growth with the addition of P-laden biochars as fertilizer are seriously inhibited due to the high alkalinity, particularly for MB. The environmental risk of P-laden biochars (with high alkalinity and salt content) as fertilizer should be emphasized in practical application.

Influence of Synthesis Methods on the High-Efficiency Removal of Cr(VI) from Aqueous Solution by Fe-Modified Magnetic Biochars

Fe-modified biochars have been widely used in removal of Cr(VI) from water due to the resulting modified surface functional groups and magnetization property. However, few studies have synthetically investigated modification methods and synthesis parameters on the improvement of the removal efficiency of Cr(VI) by Fe-modified biochars. Herein, 10 types of corn straw-based magnetic biochars were produced using pre-modification and post-modification methods with various modifier ratios, and the highest heating temperature (HHT). Cr(VI) removal results suggest that the removal efficiency of pre-modified biochars ranged from 50.7 to 98.6%, which was much higher than that of post-modified (6.6-21.6%) and unmodified biochars (0.4-7.6%). The effect of synthesis methods on Cr(VI) adsorption was in the following order: Fe-modification method > modifier ratio > HHT. The adsorption kinetics and isotherm results of three types of pre-modified biochars were well fitted with the pseudo-second-order model (R ² > 0.99) and the Langmuir adsorption model (R ² > 0.99), respectively, indicating the surface homogeneity of the pre-modified biochars and unilayer chemisorptions of Cr(VI). Characterization results show that iron oxides or zerovalent iron particles were successfully deposited onto the surface of biochars and magnetism was introduced. A good Pearson correlation (r = -0.9694) between the removal efficiency and pH value in modified biochar suggests that the lower pH value may offer more positive charges and promote electrostatic attraction. Therefore, the dominant mechanism for enhanced Cr(VI) adsorption on pre-modified biochar was electrostatic attraction, resulting from its distinguished acidity nature. Our findings provide new insights into the high-efficiency removal of Cr(VI) onto Fe-modified magnetic biochars and will benefit future design of more efficient magnetic biochars.

Efficient Removal 17-Estradiol by Graphene-Like Magnetic Sawdust Biochar: Preparation Condition and Adsorption Mechanism

The occurrence of environmental endocrine disrupting chemicals (EDCs) in aquatic environments has caused extensive concern. Graphene-like magnetic sawdust biochar was synthesized using potassium ferrate (K₂FeO₄) to make activated sawdust biochar and applied for the removal of 17-estradiol (E2). The characterization showed that the surface morphology of five graphene-like magnetic sawdust biochars prepared with different preparation conditions were quite different. The specific surface area and pore structure increased with the increment of K₂FeO₄ addition. The results have shown that graphene-like magnetic sawdust biochar (1:1/900 °C) had the best removal on E2. The experimental results indicated that pseudo-first-order kinetic model and the Langmuir model could describe the adsorption process well, in which the equilibrium adsorption capacity (q_e,1) of 1:1/900 °C were 59.18 mg·g⁻¹ obtained from pseudo-first-order kinetic model and the maximum adsorption capacity (q_max) of 1:1/900 °C were 133.45 mg·g⁻¹ obtained from Langmuir model at 298K. At the same time, lower temperatures, the presence of humic acid (HA), and the presence of NaCl could be regulated to change the adsorption reaction in order to remove E2. Adsorption capacity was decreased with the increase of solution pH because pH value not only changed the surface charge of graphene-like magnetic sawdust biochar, but also affected the E2 in the water. The possible adsorption mechanism for E2 adsorption on graphene-like magnetic sawdust biochar was multifaceted, involving chemical adsorption and physical absorption, such as H-bonding, π-π interactions, micropore filling effects, and electrostatic interaction. To sum up, graphene-like magnetic sawdust biochar was found to be a promising absorbent for E2 removal from water.