Numerical simulation of 222Rn profiling in an experimental chamber using CFD technique

Numerical simulation application in occupational health studies: a review

Most occupational hazardous agents in workplaces should be evaluated and controlled. Different methods exist for identifying, evaluating and controlling these agents, such as numerical simulation tools. Numerical simulations can help experts to improve occupational health. Due to the importance and abilities of numerical simulations, this study divided occupational hazardous agents into 10 subgroups. These subgroups included air pollution, ventilation, respiratory airways, noise and vibration, lighting, radiation, ergonomics, fire and explosion, risk assessment and personal protective equipment. Recent research studies in each subgroup were then reviewed, and the codes and software used in simulations were determined. The results show that Fluent software and k-ϵ turbulence models are the most used in occupational health studies simulations. Today, different codes and software have been developed for simulation, and we suggest their use in occupational health studies.

Novel approaches for accurately measuring radon exhalation rate and mechanism interpreted by numerical simulation

Measurements of radon exhalation rate using traditional methods can be affected by back-diffusion or differential pressure in the accumulation chamber, resulting in deviations between the measured and the true values. To obtain an accurate radon exhalation rate for evaluation of radon-risk regions, two novel approaches of measurements based on traditional methods were proposed. Repeated experiments were implemented on a self-designed stainless cylindrical vessel filled with uranium tailings sand. The measured radon exhalation rates on average were 0.51 ± 0.02 and 0.52 ± 0.02 Bq m-2 s-1 for the two proposed methods, with 0.02% and 0.04%, respectively, deviations from the theoretical value. In addition, numerical techniques were employed to interpret the defects of traditional methods and mechanisms of proposed approaches to measure accurate values. Two novel approaches have significantly reduced the impact of back diffusion and differential pressure inside the chamber and consumed less time.

A CFD-based approach to study the deposition and distribution behaviour of 212Pb in a calibration chamber

Among the several aspects of decay products behavior, deposition is of special significance because of its prominent role in the activity removal from the environment, which eventually results in the occurrence of decay product disequilibrium with the parent gas. This point is particularly important in case of thoron dosimetry where thoron progeny ²¹²Pb accounts for the most of the radiological dose. The deposition depends on the size distribution of decay products and the structure of air turbulence at the air-surface interface. In the present work, the effect of varying air-flow (fan speed) and aerosol count median diameter (CMD) was studied on the deposition and distribution profile of ²¹²Pb using computational fluid dynamics (CFD). The simulations have been carried out in a cubical calibration chamber of volume 8 m³, facilitated at RP&AD, BARC. Simulated results showed that the increase of total depositional loss rate of attached fraction of ²¹²Pb due to increase of the fan speed was significant for CMD up to 400 nm, beyond which this effect started becoming less prominent with increasing diameter. Besides, a minimum of the total depositional loss rate curve was seen to be shifted to the higher CMD with increase of the fan speed. CFD results were found to be in good agreement with experimental observations obtained in the controlled conditions with thoron source.

A CFD-based approach to optimize operating parameters of a flow-through scintillation cell for measurement of 220Rn in indoor environments

The measurements and monitoring of ²²²Rn/²²⁰Rn have been of emerging interest in occupational environments particularly in radium/thorium handling facilities and environments with monazite deposits for the inhalation dosimetry. The performance of a flow-through Lucas scintillation cell (LSC) for long run ²²⁰Rn measurements, depends upon the exact distribution pattern of ²²⁰Rn and its decay products in the LSC which can vary with the design of inlet path and flow rates. In this work, the CFD technique has been used to study the concentration profiles of ²²⁰Rn and its decay products in LSC for varying flow rates and inlet needle lengths. The variation of alpha production efficiency (η_α) is computed and analyzed for each case; aiming to select the best operating range of parameters for the optimum performance of LSC for ²²⁰Rn measurements. It is seen that LSC can be operated in the flow rate ranging from 0.6 to 1 lpm with inlet needle length varying from 22.5 to 45 mm for improved sensitivity.

Implications on dose estimation and dispersion patterns of thoron in a typical indoor environment

A model that describes the pollutant sources/sinks and inlet-outlet can help to assess the indoor exposure. Short half-life of radioactive thoron (²²⁰Rn) makes it vital and an interesting element to study its dispersion behavior. This work presents an extensive depiction of the influence of indoor environment thoron dispersion under fixed boundary conditions within the volume domain of 90 m³ using computational fluid dynamics (CFD) software. For the desirable air flow, inlet and outlet are considered in the room and the k-ɛ model is used. The thoron distribution is studied at different locations and different heights to cover the whole room. Obtained dispersion patterns vary at different locations and indicate non-uniformity of thoron level with elevated values in the room corners. Mean concentration was found to be 11 Bq/m³ with the exhalation rate of 0.102 Bqm^-2 s^-1. Some stagnant zones were found especially at the corners where the concentration is almost 5 times the average concentration. Such varying thoron level results in the overestimation and underestimation of the dose. The inhomogeneous behavior of thoron may cause variation in equilibrium factor. A simulated model is beneficial in understanding the radioactive gas behavior and has its importance in planning to find the correct dose estimation and, therefore, the best mitigation techniques.