Catalytic performance of a metal-free graphene oxide-Al2O3 composite assembled by 3D printing

High electrical characteristics through graphene oxide doping process on physicochemically reformed inorganic thin films

This study investigated the improvement of the electro-optical properties of a liquid crystal (LC) cell fabricated through brush coating using graphene oxide (GO) doping. The physical deformation of the surface was analyzed using atomic force microscopy. The size of the groove increased as the GO dopant concentration increased, but the direction of the groove along the brush direction was maintained. X-ray photoelectron spectroscopy analysis confirmed that the number of C-C and O-Sn bonds increased as the GO concentration increased. Since the van der Waals force on the surface increases as the number of O-metal bonds increases, we were able to determine why the anchoring energy of the LC alignment layer increased. This was confirmed by residual DC voltage and anchoring energy measurements that were later performed. As the GO concentration increased, the width of the hysteresis curve decreased, indicating that the residual DC voltage decreased. Additionally, the 15% GO-doped sample exhibited a significant increase in its anchoring energy up to 1.34 × 10-3 J/m2, which is similar to that of rubbed polyimide. It also secured a high level of electro-optical properties and demonstrated potential as a next-generation thin-film display despite being produced via a simple brush-coating process.

Polymer–Nickel Composite Filaments for 3D Printing of Open Porous Materials

Catalysis has been a key way of improving the efficiency-to-cost ratio of chemical and electrochemical processes. There have been recent developments in catalyst materials that enable the development of novel and more sophisticated devices that, for example, can be used in applications, such as membranes, batteries or fuel cells. Since catalytic reactions occur on the surface, most catalyst materials are based on open porous structures, which facilitates the transport of fluids (gas or liquid) and chemical (or electrochemical) specific surface activity, thus determining the overall efficiency of the device. Noble metals are typically used for low temperature catalysis, whereas lower cost materials, such as nickel, are used for catalysis at elevated temperatures. 3D printing has the potential to produce a more sophisticated fit for purpose catalyst material. This article presents the development, fabrication and performance comparison of three thermoplastic composites where PLA (polylactic acid), PVB (polyvinyl butyral) or ABS (acrylonitrile butadiene styrene) were used as the matrix, and nickel particles were used as filler with various volume fractions, from 5 to 25 vol%. The polymer–metal composites were extruded in the form of filaments and then used for 3D FDM (Fused Deposition Modeling) printing. The 3D printed composites were heat treated to remove the polymer and sinter the nickel particles. 3D printed composites were also prepared using nickel foam as a substrate to increase the final porosity and mechanical strength of the material. The result of the study demonstrates the ability of the optimized filament materials to be used in the fabrication of high open porosity (over 60%) structures that could be used in high-temperature catalysis and/or electrocatalysis.

3D-Printed Porous Magnetic Carbon Materials Derived from Metal-Organic Frameworks

Here we report new porous carbon materials obtained by 3D printing from photopolymer compositions with zinc- and nickel-based metal–organic frameworks, ZIF-8 and Ni-BTC, followed by high-temperature pyrolysis. The pyrolyzed materials that retain the shapes of complex objects contain pores, which were produced by boiling zinc and magnetic nickel particles. The two thus provided functionalities—large specific surface area and ferromagnetism—that pave the way towards creating heterogenous catalysts that can be easily removed from reaction mixtures in industrial catalytic processes.

Applications of Ceramic/Graphene Composites and Hybrids

Research activity on ceramic/graphene composites and hybrids has increased dramatically in the last decade. In this review, we provide an overview of recent contributions involving ceramics, graphene, and graphene-related materials (GRM, i.e., graphene oxide, reduced graphene oxide, and graphene nanoplatelets) with a primary focus on applications. We have adopted a broad scope of the term ceramics, therefore including some applications of GRM with certain metal oxides and cement-based matrices in the review. Applications of ceramic/graphene hybrids and composites cover many different areas, in particular, energy production and storage (batteries, supercapacitors, solar and fuel cells), energy harvesting, sensors and biosensors, electromagnetic interference shielding, biomaterials, thermal management (heat dissipation and heat conduction functions), engineering components, catalysts, etc. A section on ceramic/GRM composites processed by additive manufacturing methods is included due to their industrial potential and waste reduction capability. All these applications of ceramic/graphene composites and hybrids are listed and mentioned in the present review, ending with the authors' outlook of those that seem most promising, based on the research efforts carried out in this field.