A generalised model for cheese mass loss determination during ripening

Modeling weight loss of cheese during ripening and the influence of dairy system, parity, stage of lactation, and composition of processed milk

The yield, flavor, and texture of ripened cheese result from numerous interrelated microbiological, biochemical, and physical reactions that take place during ripening. The aims of the present study were to propose a 2-compartment first-order kinetic model of cheese weight loss over the ripening period; to test the variation in new informative phenotypes describing this process; and to assess the effects on these traits of dairy farming system, individual farms within dairy system, animal factors, and milk composition. A total of 1,211 model cheeses were produced in the laboratory using individual 1.5-L milk samples from Brown Swiss cows reared on 83 farms located in Trento Province. During ripening (60 d; temperature 15°C, relative humidity 85%), the weight of all model cheeses was measured, and cheese yield (cheese weight/processed milk weight, %CY) was calculated at 7 intervals from cheese-making (0, 1, 7, 14, 28, 42, and 60 d). Using these measures, a 2-compartment first-order kinetic model (3-parameter equation) was developed for modeling %CY during the ripening period, as follows: [Formula: see text] , where %CY_t is the %CY at ripening time t; %CY_i and %CY_f are the modeled %CY traits at time 0 d (%CY_i = initial %CY) and at the end of a ripening period sufficient to reach a constant wheel weight (%CY_f = final %CY after 60 d ripening in the case of small model cheeses); k_CY is the instant rate constant for cheese weight loss (%/d). Cheese weight and protein and fat losses were calculated as the % difference between the model cheeses at 0 and after 60 d of ripening. The variation in cheese pH was calculated as the % difference between pH at 0 and after 60 d. Dairy system, individual herd within dairy system, and the cow's parity and lactation stage (tested with a linear mixed model) strongly affected almost all the traits collected during model cheese ripening. Milk fat, protein, lactose, pH, and somatic cell score also greatly affected almost all the traits, although k_CY was affected only by milk protein. After including milk composition in the linear mixed model, the importance of all the herd and animal sources of variation was greatly reduced for all traits. The proposed model and novel traits could be tested, first, with the aim of establishing new monitoring procedures enabling the dairy industry to improve milk quality-based payment systems at the herd level and, second, with a view to exploring possible genetic improvements to dairy cow populations.

Penicillium commune affects textural properties and water distribution of hard and extra-hard cheeses

We analyzed the effects of growth of Penicillium commune, one of the most frequent fungal species associated with cheese, on the water diffusion and texture of hard and extra-hard cheeses. A total of 36 hard cheese blocks and 36 extra-hard cheese blocks were manufactured, salted at different levels (0.5, 1.25 and 2% w/w), and assigned to different treatments (control and inoculated). Cheese texture was analyzed using a penetration needle probe at 2 and 5 weeks after ripening. Firmness, defined as the maximum force detected in the penetration probe, was higher in both hard and extra-hard inoculated cheese blocks compared with the control. In addition, the presence of fungal growth on cheese rind increased the total work of penetration (a measure of resistance to probe penetration), but only in extra-hard cheeses, suggesting that the moisture of cheese might be affecting the growth capacities and performance of P. commune. The change in textural properties of cheeses was linked to desiccation of the upper 0.5-cm rind layer mediated by P. commune.

Effect of different thistle flower ecotypes as milk-clotting in Serra da Estrela cheese

Purpose

Thistle flower (Cynara cardunculus) aqueous extracts, as rich source of milk-clotting peptidases, have been widely used for cheeses marketed under the Registry of the Protected Designation of Origin, as it is the case of Serra da Estrela cheese, manufactured from raw ewes’ milk and without addition of any commercial starter culture. This paper aims at studying the influence of six different ecotypes of thistle flowers in cheese properties during the ripening and of final products.

Design/methodology/approach

Cheeses were produced with different thistle flower extracts and then the clotting time, weight and colour of cheeses, as well as texture properties and sensorial characteristics, were evaluated.

Findings

The clotting time varied from 47 to 66 min, and the weight loss along ripening varied between 32 and 40 per cent. There was some influence of thistle flower ecotype on the colour during ripening and in the final product. The results of texture analysis revealed significant differences between the thistle ecotypes: crust firmness varying from 2.4 to 5.6 N; inner firmness from 0.82 to 1.82 N; stickiness from −0.5 to −1.60 N; adhesiveness from −3.0 to −11.3 N.s; and Ecotype C was particularly distinguishable. Sensorial evaluation revealed differences among the cheeses, with Ecotype C receiving the highest score for global appreciation.

Originality/value

The usage of different extracts of thistle flower to produce Serra da Estrela cheese with different properties is a novelty, and it allows the possibility of manipulating this parameter in the future so as to produce cheeses with specific characteristics, addressed to different consumer targets.