Development of dispersive liquid-liquid microextraction method for the analysis of organophosphorus pesticides in tea

Synthesis of green nanosorbent from bovine serum albumin and curcumin for magnetic solid phase extraction of pesticides from food samples

For the first time, a magnetic carbon nanocomposite was synthesized using one-step hydrothermal procedure, employing bovine serum albumin, curcumin, and ferric ammonium citrate. Additionally, the application of this novel composite as an adsorbent for magnetic dispersive solid phase extraction of fungicides and pesticides from water and food samples is a unique aspect of this study. Under optimum conditions (salt concentration: 5.0% w/v, pH: 7.0, desorption solvent: ethanol, sorbent amount: 20 mg, extraction time: 20 min, desorption time: 3 min, stirring rate: 500 rpm, sample volume: 30 mL, extraction temperature: room temperature, and desorption solvent volume: 150 μL) linearity (2.5 to 1400 ng mL-1), coefficients of determination (R2 ≥ 0.997), limits of detection (0.75 to 1.5 ng mL-1), and limits of quantification (2.5 to 5.0 ng mL-1) were achieved. The method validation results showed extraction recovery ranging from 71.2% to 93.4%, and preconcentration factors ranging from 142.5 to 186.1.

Pesticide residues in herbs and their transfer for infusions

In this work, a cost-effective gas chromatography-mass spectrometry method was validated for the analysis of twenty-five pesticide residues in herbs and infusions using a quick, easy, cheap, effective, rugged, and safe procedure or a dispersive liquid-liquid microextraction method, respectively. Figures of merit of the method showed good accordance with current guidelines. From the 58 herb samples studied (pertaining to 20 different species), 80% presented at least one detectable pesticide, with 62% of them above the maximum residual level. Results showed that pesticide residues from naturally contaminated herbs were not transferred at a significant rate to the herbal infusions. When a control assay was conducted by spiking a blank herb sample with a large amount of each pesticide (7 mg/L) 15 analytes were detected below the limit of quantification in the infusion.

Investigation of organophosphorus (OPs) compounds by a needle trap device based on mesoporous organo-layered double hydroxide (organo-LDH)

Organophosphorus (OPs) compounds can endanger human health and the environment by inhibiting the acetylcholinesterase enzyme. But these compounds have been widely used as pesticides due to their effectiveness against all kinds of pests. In this study, a Needle Trap Device (NTD) packed with mesoporous organo-layered double hydroxide (organo-LDH) material and coupled with gas chromatography-mass spectrometry (GC-MS) was employed for the sampling and analysis of OPs compounds (diazinon, ethion, malathion, parathion, and fenitrothion). In this way, the [magnesium-zinc-aluminum] layered double hydroxide ([Mg-Zn-Al] LDH) modified with sodium dodecyl sulfate (SDS) as a surfactant was prepared and characterized by FT-IR, XRD, BET, and FE-SEM, EDS, and elemental mapping techniques. Then, various parameters such as relative humidity, sampling temperature, desorption time, and desorption temperature were evaluated by the mesoporous organo-LDH:NTD method. The optimal values of these parameters were determined using response surface methodology (RMS) and central composite design (CCD). The optimal temperature and relative humidity values were obtained as 20 °C and 25.0%, respectively. On the other hand, the desorption temperature and time values were in the range of 245.0-254.0 °C and 5 min, respectively. The limit of detection (LOD) and limit of quantification (LOQ) were reported in the range of 0.02-0.05 mg m^-3 and 0.09-0.18 mg m^-3, respectively, which shows the high sensitivity of the proposed method compared to the usual methods. The repeatability and reproducibility of the proposed method (by calculating the relative standard deviation) was estimated in the range of 3.8-10.10 which indicates the acceptable precision of the organo-LDH:NTD method. Also, the desorption rate of the stored needles at 25 °C and 4 °C, was determined to be 86.0% and 96.0%, respectively after 6 days. The results of this study proved that the mesoporous organo-LDH:NTD method can be utilized as a fast, simple, environmentally friendly, and effective method for sampling and determining OPs compounds in the air.

A new application of continuous sample drop flow microextraction using octanoic acid as a green extraction solvent for the determination of antibiotic drugs in urine samples

In this study, octanoic acid (OA) was used as an extraction solvent for the pre-concentration and determination of three antibiotic drugs (levofloxacin, metronidazole, and tinidazole) in urine samples. To extract the antibiotic drugs, a green solvent was used as the extraction solvent in the continuous sample drop flow microextraction method, followed by a high-performance liquid chromatography photodiode array detector. According to the findings, the present study offers an environmentally friendly analytical method with a high capacity for the microextraction of the antibiotic drugs at very low concentrations. The calculated detection limits were 6.0-10.0 µg/L and the linear range was found between 20 and 780 µg/L. The proposed method showed excellent repeatability with the RSD values ranging from 2.8 to 5.5%. The relative recoveries were between 79.0 and 92.0% in the urine samples with spiked levels of 40.0-100.0 µg/L for metronidazole and tinidazole, and 100.0-200.0 μg/L for levofloxacin.

Development of a new and facile method for determination of chlorpyrifos residues in green tea by dispersive liquid-liquid microextraction

In this work a simple, rapid, and environmentally friendly method has been established for the determination of chlorpyrifos residue in green tea by dispersive liquid-liquid microextraction and gas chromatography-flame photometric detection. Some experimental parameters that influence extraction efficiency, such as the kind and volume of disperser solvents and extraction solvents, extraction time, addition of salt and pH, were investigated. And the optimal experimental conditions were obtained, quantitative analysis was carried out using external standard method. The correlation coefficient of the calibration curves was 0.999 with in 0.05 mg/kg to 5 mg/kg. The results showed that under the optimum conditions, the enrichment factors of the chlorpyrifos was about 554.51, the recoveries for standard addition fell in the range from 91.94 to 104.70% and the relative standard deviations was 4.61%. The limit of quantification of chlorpyrifos in green tea was 0.02 μg/mL at the signal/noise ratio of 3.

The performance of water-soluble fluoride transformation in soil-tea-tea infusion chain system and the potential health risk assessment

BACKGROUND

Water-soluble fluoride (WS-F) can be absorbed directly by tea plants from soil and comprises a major source of dietary F in tea consumers. To reveal the WS-F accumulation in tea leaves and assess WS-F health risks, 70 sets of samples including tea leaves at three maturity stages and corresponding topsoil were collected from Xinyang, China. The WS-F contents in tea samples and pH values in soil samples were determined.

RESULTS

The contents of WS-F in tea leaves exhibited a positive correlation with leaf maturity. The contents of WS-F in tea leaves showed a positive correlation with WS-F contents in the soil as the soil pH value exceeds 5. All the bud with two leaves samples, 84.29% of the third to sixth leaves samples, and 78.57% mature leaves samples in 5-min infusion tend to be no health threat. The leaching characteristics of WS-F from tea leaves were influenced by the leaf maturity and soaking time.

CONCLUSION

Taking measures to control pH and WS-F concentration of plantations soil, as well as drinking tea infusion made from young leaves or reducing soaking time could decrease the WS-F health risk. © 2021 Society of Chemical Industry.

Analytical Extraction Methods and Sorbents' Development for Simultaneous Determination of Organophosphorus Pesticides' Residues in Food and Water Samples: A Review

Extensive use of organophosphorus pesticides in agriculture leads to adverse effects to the environment and human health. Sample preparation is compulsory to enrich target analytes prior to detection as they often exist at trace levels and this step is critical as it determines the concentration of pollutants present in samples. The selection of a suitable extraction method is of great importance. The analytical performance of the extraction methods is influenced by the selection of sorbents as sorbents play a vital role in the sensitivity and selectivity of an analytical method. To date, numerous sorbent materials have been developed to cater to the needs of selective and sensitive pesticides' detection. Comprehensive details pertaining to extraction methods, developed sorbents, and analytical performance are provided. This review intended to provide a general overview on different extraction techniques and sorbents that have been developed in the last 10 years for organophosphorus pesticides' determinations in food and water samples.

Development of a SPE/GC-MS method for the determination of organophosphorus pesticides in food samples using syringe filters packed by GNP/MIL-101(Cr) nanocomposite

In this study, we report the synthesis and application of a nanocomposite comprising metal-organic framework MIL-101(Cr) and graphene nanopowder (GNP) as a promising sorbent for the extraction of organophosphorus pesticides (OPPs) in juices, water, vegetables and honey samples. A syringe filter, for the first time, was used to host the synthesized nanocomposite and extract the OPPs followed by GC-MS analysis. Different characterization methods including XRD, FTIR, TGA, BET and SEM were employed to confirm the formation of studied nanocomposite. The results indicated that the GNP/MIL-101(Cr) could provide higher capacity for adsorption of OPPs and lower detection limit compared to pristine MIL-101(Cr). The detection limits were 0.005 to 15.0 µg/Kg and the linear range found between 0.05 and 400 µg/Kg. The proposed method showed very good repeatability with the RSD values ranging from 2.9% to 7.1%. The recoveries were between 84% -110% with the spiked levels of 2.0-100.0 µg/Kg.

Nanostructured β‐tricalcium Phosphate (Ca3(PO4)2 Based Electrochemical Sensor for Detection of Methyl Parathion and Mercury (II) Ions

In this work, we have fabricated a new electrochemical sensor based on β‐tricalcium phosphate (Ca3(PO4)2) nanoparticles (NPs) modified glassy carbon electrode (GCE) for the selective nonenzymatic determination of methyl parathion and mercury (II) ions independently. β‐tricalcium phosphate (β‐TCP) NPs were prepared by chemical precipitation method and structural and morphological properties were investigated by XRD, FTIR, and SEM. The electrochemical behavior of MP and mercury (Hg2+) ions were investigated by cyclic voltammetry (CV) and square wave voltammetry (SWV) techniques using β‐TCP/GCE. The modified electrode exhibited excellent electrocatalytic activity towards both the MP and Hg over a wide linear range from 0.15 to 141 μM and 1–381 µM with the lowest detection limits of 88 and 136.4 nM respectively. The sensor has high selectivity towards MP and Hg in the presence of major interfering compounds such as 3-nitrophenol, 4-nitrophenol, 4-aminophenol, catechol, hydroquinone and heavy metals such as lead, cadmium and arsenic. Applicability of the fabricated sensor for detection of MP and Hg (II) ions has been tested in tap water by standard addition method.

Application of liquid-phase microextraction to the analysis of plant and herbal samples

INTRODUCTION

The analysis of plant and herbal samples is a challenging task for analytical chemists due to the complexity of the matrix combined with the low concentration of analytes. In recent years different liquid-phase microextraction (LPME) techniques coupled with a variety of analytical equipment have been developed for the determination of both organic and inorganic analytes.

OBJECTIVE

Over the past few years, the number of research papers in this field has shown a markedly growing tendency. Therefore, the purpose of this review paper is to summarise and critically evaluate research articles focused on the application of LPME techniques for the analysis of plant and herbal samples.

RESULTS

Due to the complex nature of the samples, the direct application of LPME techniques to the analysis of plants has not often been done. LPME techniques as well as their modalities have been commonly applied in combination with other pretreatment techniques, including a solid-liquid extraction technique supported by mechanical agitation or auxiliary energies for plant analysis. Applications and the most important parameters are summarised in the tables.

CONCLUSION

This review summarises the application of the LPME procedure and shows the major benefits of LPME, such as the low volume of solvents used, high enrichment factor, simplicity of operation and wide selection of applicable detection techniques. We can expect further development of microextraction analytical methods that focus on direct sample analysis with the application of green extraction solvents while fully automating procedures for the analysis of plant materials.

Solid-phase microextraction of organophosphorous pesticides from food samples with a nitrogen-doped porous carbon derived from g-C3N4 templated MOF as the fiber coating

A nitrogen-doped metal organic framework (MOF) based porous carbon (C-(C₃N₄@MOF)) was produced by the carbonization of a graphitic carbon nitride (g-C₃N₄) templated MOF (NH₂-MIL-125). The C-(C₃N₄@MOF) was then coated on a stainless steel wire by sol-gel technique to serve as a solid-phase microextraction (SPME) fiber coating. The coated fiber was studied for the extraction of fourteen organophosphorous pesticides (OPPs) from different fruit and vegetable samples followed by gas chromatography-mass spectrometer (GC-MS) detection. The C-(C₃N₄@MOF) coated fiber exhibited a high extraction capability for the OPPs. Both single factor optimization and response surface analysis (Box-Behnken Design) methods were implemented to optimize the experiment conditions for the extraction. The results indicated that the linear response for the fourteen OPPs was in the range from 0.69 to 3000 ng g^-1 and the coefficients of determination (r²) ranged from 0.9981 to 0.9998. The limits of detection (LODs, S/N = 3) ranged from 0.23 to 7.5 ng g^-1. The method recoveries (R) of the fourteen OPPs for spiked fruit and vegetable samples were between 82.6% and 118%, with the relative standard deviations (RSDs) varying from 2.8% to 11.7%. The fiber can be reused over 100 times without a significant loss of extraction efficiency.

Rational design of an ionic liquid dispersive liquid–liquid micro-extraction method for the detection of organophosphorus pesticides

In this study, a functionalized ionic liquid (IL), [MimCH₂COOCH₃][NTf₂] was rationally designed and explored as an extraction solvent in dispersive liquid–liquid microextraction (DLLME) combined with ultra-high performance liquid chromatography (UHPLC) for the sensitive determination of organophosphorus pesticides (OPs).

A novel high-performance liquid chromatography-fluorescence analysis coupled with in situ degradation-derivatization technique for quantitation of organophosphorus thioester pesticide residues in tea

A novel high-performance liquid chromatography-fluorescence analysis in combination with in situ degradation-derivatization (ISD-D) technique was developed for simultaneous determination of seven organophosphorus thioester pesticides (OPTPs) in tea. The ISD-D technique was based on degradation of OPTPs by a nucleophilic substitution reaction between phenylbutane-1,2,3-trione-2-oxime and OPTPs, which can give thiol degradation products (DPs). The thiol DPs obtained were derivatized with the novel derivatization reagent N-(4-(carbazole-9-yl)-phenyl)-N-maleimide (NCPM) in a syringe. Attractively, NCPM itself did not fluoresce, whereas the derivatives of the thiol DPs fluoresced intensely, with excitation and emission maxima at 290 nm and 368 nm, respectively, which extraordinary reduced the background interference and increased the detection sensitivity for thiol DPs. Excellent linearity (R² > 0.995) for all OPTPs was achieved, with limits of detection and limits of quantitation ranging from 0.23 to 0.45 μg/kg and from 0.75 to 1.43 μg/kg, respectively. Satisfactory recoveries ranging from 90.5% to 96.0% were obtained for all OPTPs. The ISD-D technique provided a novel and sensitive strategy for quantitation of trace amounts of OPTPs in real samples. Graphical abstract ᅟ.

Sensitive determination of atorvastatin in human plasma by dispersive liquid-liquid microextraction and solidification of floating organic drop followed by high-performance liquid chromatography

A novel and sensitive dispersive liquid-liquid microextraction method based on the solidification of the floating organic drop combined with high-performance liquid chromatography and ultraviolet detection was used for the determination of atorvastatine in blood serum samples. The chromatographic separation of atorvastatin was carried out using methanol as the mobile phase organic modifier. Various parameters affecting the extraction efficiency were optimized, such as the kind and volume of extraction solvent (1-undecanol) and disperser solvent (acetonitrile), pH, and the extraction time. The calibration curve was linear in the range of 0.2-6000 μg/L of atorvastatin (r(2) = 0.995) with a limit of detection of 0.07 μg/L. The relative standard deviation for 100 μg/L of atorvastatin in human plasma was 8.4% (n = 4). The recoveries of plasma samples spiked with atorvastatin were in the range of 98.8-113.8%. The obtained results showed that the proposed method is fast, simple, and reliable for the determination of very low concentrations of atorvastatin in human plasma samples.

Vortex-assisted low density solvent based demulsified dispersive liquid-liquid microextraction and high-performance liquid chromatography for the determination of organophosphorus pesticides in water samples

A simple, rapid, effective and eco-friendly preconcentration method, vortex-assisted low density solvent based solvent demulsified dispersive liquid-liquid microextraction (VLDS-SD-DLLME), followed by high performance liquid chromatography-diode array detector (HPLC-DAD) analysis, has been developed for the first time for the determination of four organophosphorus pesticides (OPPs) (e.g., azinphos-methyl, parathion-methyl, fenitrothion and diazinon) in environmental water samples. In this preconcentration procedure, an emulsion was obtained after the mixture of extraction solvent (1-dodecanol) and dispersive solvent (acetonitrile, ACN) was injected rapidly into 10 mL of the sample solution. The vortex agitator aided the dispersion of the extraction solvent into the sample solution. After the formation of an emulsion, the demulsifier (ACN) was added, resulting in the rapid separation of the mixture into two phases without centrifugation. Under optimal conditions, the proposed method provided high extraction efficiency (90-99%), good linearity range (0.5-500 ng mL(-1)), low limits of detection (0.25-1 ng mL(-1)) and good repeatability and recoveries were obtained.

Organophosphorus pesticide and ester analysis by using comprehensive two-dimensional gas chromatography with flame photometric detection

Thirty-seven phosphorus (P)-containing compounds comprising organophosphorus pesticides and organophosphate esters were analyzed by using comprehensive two-dimensional gas chromatography with flame photometric detection in P mode (GC × GC-FPD(P)), with a non-polar/moderately polar column set. A suitable modulation temperature and period was chosen based on experimental observation. A number of co-eluting peak pairs on the (1)D column were well separated in 2D space. Excellent FPD(P) detection selectivity, responding to compounds containing the P atom, produces clear 2D GC × GC plots with little interference from complex hydrocarbon matrices. Limits of detection (LOD) were within the range of 0.0021-0.048 μmol L(-1), and linear calibration correlation coefficients (R(2)) for all 37 P-compounds were at least 0.998. The P-compounds were spiked in 2% diesel and good reproducibility for their response areas and retention times was obtained. Spiked recoveries were 88%-157% for 5 μg L(-1) and 80%-138% for 10 μg L(-1) spiked levels. Both (1)tR and (2)tR shifts were noted when the content of diesel was in excess of 5% in the matrix. Soil samples were analyzed by using the developed method; some P-compounds were positively detected. In general, this study shows that GC × GC-FPD(P) is an accurate, sensitive and simple method for P-compound analysis in complicated environmental samples.

Microextraction techniques for the determination of volatile and semivolatile organic compounds from plants: a review

Vegetables and fruits are necessary for human health, and traditional Chinese medicine that uses plant materials can cure diseases. Thus, understanding the composition of plant matrix has gained increased attention in recent years. Since plant matrix is very complex, the extraction, separation and quantitation of these chemicals are challenging. In this review we focus on the microextraction techniques used in the determination of volatile and semivolatile organic compounds (such as esters, alcohols, aldehydes, hydrocarbons, ketones, terpenes, sesquiterpene, phenols, acids, plant secondary metabolites and pesticides) from plants (e.g., fruits, vegetables, medicinal plants, tree leaves, etc.). These microextraction techniques include: solid phase microextraction (SPME), stir-bar sorptive extraction (SBSE), single drop microextraction (SDME), hollow fiber liquid phase microextraction (HF-LPME), dispersive liquid liquid microextraction (DLLME), and gas purge microsyringe extraction (GP-MSE). We have taken into consideration papers published from 2008 to the end of January 2013, and provided critical and interpretative review on these techniques, and formulated future trends in microextraction for the determination of volatile and semivolatile compounds from plants.

Determination of pesticide residues in ginseng by dispersive liquid-liquid microextraction and ultra high performance liquid chromatography-tandem mass spectrometry

A procedure involving acetonitrile-based extraction combined with dispersive liquid-liquid microextraction (DLLME) and detection by ultra high performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS) was used for determination of 39 pesticides in ginseng. The extraction of pesticide residues in ginseng was performed with acetonitrile, applying QuEChERS methodology, and the extract was further disposed by DLLME method before analyzed by UHPLC-MS/MS. The average recoveries ranged from 70 to 120% for 82% of the analytes with RSD lower than 15%. The calibration curves obtained with blank matrices were linear with a correlation coefficient of over 0.99. The limits of detection were between 0.01 and 1.0μg/kg. Matrix effects were studied by comparing solvent calibration curves and matrix-matched calibration curves. The results indicate the feasibility of this method for the determination of 39 pesticides in ginseng.

Enantioselective behavior of malathion enantiomers in toxicity to beneficial organisms and their dissipation in vegetables and crops

The dissipation behavior of the two enantiomers of malathion was elucidated in five plant species using enantioselective high performance liquid chromatography (HPLC), and the acute toxicity of the individual enantiomers toward earthworms and honeybees was studied. The calculated LC(50) values of the R-, S- and rac-malathion to earthworms were 0.3869, 25.17, and 19.19 μg/cm(2), respectively, while the calculated LC(50) values of R-, S- and rac-malathion to bees were 2.15, 36.67, and 7.11 μg/mL, respectively. This indicated that the R-enantiomer was more toxic than S-enantiomer. The results of the degradation of racemate in Chinese cabbage and rape showed that the inactive S-(-)-enantiomer degraded faster than the active R-(+)-enantiomer. Inversely, we found a preferential degradation of the R-(+)-enantiomer in sugar beet. However, the degradation of malathion in paddy rice and wheat were nonenantioselectivity. In all plants, malathion was degraded to levels <10% after 5 days, and the calculated t(½) values of the enantiomers ranged from 0.83 to 1.43 days in these five plants. In conclusion, our findings of enantioselectivity in the environmental fate and acute toxicity of the malathion enantiomers may have implications for better environmental and ecological risk assessment for chiral pesticides in general.