Amine functionalized graphene oxide/CNT nanocomposite for ultrasensitive electrochemical detection of trinitrotoluene

Design and optimization of a cost-effective paper-based voltammetric sensor for the determination of trinitrotoluene (TNT) utilizing cysteamine-linked Fe3O4 @Au nanocomposite

This paper presents the development and optimization of a cost-effective paper electrochemical sensor for the detection of TNT using Fe3O4-Au core-shell nanoparticles modified with cysteamine (Fe3O4@Au/CA). The sensor was constructed by modifying a graphite paste with the aforementioned nanoparticles, which facilitated the formation of a Meisenheimer complex between cysteamine and TNT as an electron donor and an electron acceptor, respectively. The central composite design was employed to optimize four key parameters pH, modifier percentage, contact time, and buffer type to enhance the performance of the sensor. The detection limit was found to be 0.5 nM of TNT, while the linear range of the electrode response spanned from 0.002 μM to 10 μM. The simplicity and low cost of the sensor make it highly attractive for practical applications, particularly in scenarios where rapid and on-site TNT detection is required.

Sensitive and selective impedimetric determination of TNT using RSM-CCD optimization

Detection of trace amounts of 2,4,6-Trinitrotoluene as a widely used explosive in the military and industrial sectors is of vital importance due to security and environmental concerns. The sensitive and selective measurement characteristics of the compound still is considered a challenge for analytical chemists. Unlike conventional optical and electrochemical methods, the electrochemical impedance spectroscopy technique (EIS), has a very high sensitivity, but it faces a significant challenge in that it requires complex and expensive steps to modify the electrode surface with selective agents. We reported the design and construction of an inexpensive, simple, sensitive, and selective impedimetric electrochemical TNT sensor based on the formation of a Meisenheimer complex between magnetic multiwalled carbon nanotubes modified with aminopropyl triethoxysilane (MMWCNTs @ APTES) and TNT. The formation of the mentioned charge transfer complex at the electrode-solution interface blocks the electrode surface and disrupts the charge transfer in [(Fe (CN) ₆)] ^3-/4- redox probe system. Charge transfer resistance changes (ΔR_CT) were used as an analytical response that corresponded to TNT concentration. To investigate the influence of effective parameters on the electrode response, such as pH, contact time, and modifier percentage, the response surface methodology based on central composite design (RSM-CCD) was used. The calibration curve was achieved in the range of 1-500 nM with a detection limit of 0.15 nM under optimal conditions, which included pH of 8.29, contact time of 479 s, and modifier percentage of 12.38% (w/w). The selectivity of the constructed electrode towards several nitroaromatic species was investigated, and no significant interference was found. Finally, the proposed sensor was able to successfully measure TNT in various water samples with satisfactory recovery percentages.

Detection of Nitroaromatic Explosives in Air by Amino-Functionalized Carbon Nanotubes

Nitroaromatic explosives are the most common explosives, and their detection is important to public security, human health, and environmental protection. In particular, the detection of solid explosives through directly revealing the presence of their vapors in air would be desirable for compact and portable devices. In this study, amino-functionalized carbon nanotubes were used to produce resistive sensors to detect nitroaromatic explosives by interaction with their vapors. Devices formed by carbon nanotube networks working at room temperature revealed trinitrotoluene, one of the most common nitroaromatic explosives, and di-nitrotoluene-saturated vapors, with reaction and recovery times of a few and tens of seconds, respectively. This type of resistive device is particularly simple and may be easily combined with low-power electronics for preparing portable devices.

Melamine functionalised multiwalled carbon nanotubes (M-MWCNTs) as a metal-free electrocatalyst for simultaneous determination of 4-nitrophenol and nitrofurantoin

An innovative melamine functionalised multiwalled carbon nanotube (M-MWCNTs) based electrochemical sensor has been developed for the determination of environmental nitro-aromatic pollutants, such as 4-nitrophenol (4-NP) and nitrofurantoin (NFT).

Detection and remediation of pollutants to maintain ecosustainability employing nanotechnology: A review

Environmental deterioration due to anthropogenic activities is a threat to sustainable, clean and green environment. Accumulation of hazardous chemicals pollutes soil, water and air and thus significantly affects all the ecosystems. This article highlight the challenges associated with various conventional techniques such as filtration, absorption, flocculation, coagulation, chromatographic and mass spectroscopic techniques. Environmental nanotechnology has provided an innovative frontier to combat the aforesaid issues of sustainable environment by reducing the non-requisite use of raw materials, electricity, excessive use of agrochemicals and release of industrial effluents into water bodies. Various nanotechnology based approaches including surface enhance scattering, surface plasmon resonance; and distinct types of nanoparticles like silver, silicon oxide and zinc oxide have contributed significantly in detection of environmental pollutants. Biosensing technology has also gained significant attention for detection and remediation of pollutants. Furthermore, nanoparticles of gold, ferric oxide and manganese oxide have been used for the on-site remediation of antibiotics, organic dyes, pesticides, and heavy metals. Recently, green nanomaterials have been given more attention to address toxicity issues of chemically synthesized nanomaterials. Hence, nanotechnology has provided a platform with tremendous applications to have sustainable environment for present as well as future generations. This review article will help to understand the fundamentals for achieving the goals of sustainable development, and healthy environment.

Colorimetric optical nanosensors for trace explosive detection using metal nanoparticles: advances, pitfalls, and future perspective

Warfare threats and acts of terror are challenging situations encountered by defense agencies across the globe and are of growing concern to the general public, and security-minded policy makers. Detecting ultra-low quantities of explosive compounds in remote locations or under harsh conditions for anti-terror purposes as well as the environmental monitoring of residual or discarded explosives in soil, remains a major challenge. The use of metal nanoparticles (NPs) for trace explosive detection has drawn considerable interest in recent years. For nano-based explosive sensor devices to meet real-life operational demands, analytical parameters such as, long-shelf life, stability under harsh conditions, ease-of-use, high sensitivity, excellent selectivity, and rapid signal response must be met. Generally, the analytical performance of colorimetric-based nanosensor systems is strongly dependent on the surface properties of the nanomaterial used in the colorimetric assay. The size and shape properties of metal NPs, surface functionalisation efficiency, and assay fabrication methods, are factors that influence the efficacy of colorimetric explosive nanosensor systems. This review reports on the design and analytical performances of colorimetric explosive sensor systems using metal NPs as optical signal transducers. The challenges of trace explosive detection, advances in metal NP colorimetric explosive design, limitations of each methods, and possible strategies to mitigate the problems are discussed.

Recent Developments in the Field of Explosive Trace Detection

Explosive trace detection (ETD) technologies play a vital role in maintaining national security. ETD remains an active research area with many analytical techniques in operational use. This review details the latest advances in animal olfactory, ion mobility spectrometry (IMS), and Raman and colorimetric detection methods. Developments in optical, biological, electrochemical, mass, and thermal sensors are also covered in addition to the use of nanomaterials technology. Commercially available systems are presented as examples of current detection capabilities and as benchmarks for improvement. Attention is also drawn to recent collaborative projects involving government, academia, and industry to highlight the emergence of multimodal screening approaches and applications. The objective of the review is to provide a comprehensive overview of ETD by highlighting challenges in ETD and providing an understanding of the principles, advantages, and limitations of each technology and relating this to current systems.

Silver embellished PANI/CNT nanocomposite for antimicrobial activity and sequestration of dye based on RSM modelling

Silver doped PANI/CNT (Ag-PANI/CNT) nanocomposite was synthesized and investigated as adsorbent for its possible application in the elimination of organic dye Brilliant Blue G (BBG). The morphological characteristics of Ag-PANI/CNT were studied using Fourier transform infrared, scanning electron microscopy, elemental mapping, transmission electron microscopy and X-ray diffraction. The response of operational parameters given as adsorbent dosage, concentration, pH and contact time for dye removal were investigated by using Response Surface Methodology (RSM). The results from RSM suggested that the efficiency of BBG elimination is 98.7 under the optimum conditions of experimental factors. The adsorption studies showed that the equilibrium data fitted well with Langmuir isotherm model compared to Freundlich. Finally, the antimicrobial activities of Ag-PANI/CNT were tested against bacterial strain Escherichia coli and Salmonella typhi and fungal strains Aspergillus niger.

A graphene electrode functionalized with aminoterephthalic acid for impedimetric immunosensing of Escherichia coli

A screen-printed electrode prepared from graphene oxide (GO) has been functionalized with 2-aminoterephthalic acid, followed by the exploitation of this functional material in an electrochemical immunoassay for Escherichia coli (E. coli) by immobilizing the antibody on its surface. The functionalization steps followed a straightforward approach and were proven by various instrumental techniques. The detection of E. coli with antibody immobilized electrodes was performed using electrochemical impedance spectroscopy. The analyses were carried out using the hexacyanoferrate redox couple as the electrochemical probe. The present method has a wide analytical range (from 2.2 × 10² to 2.2 × 10⁸ cfu.mL^-1), a low limit of detection (2 cfu.mL^-1), fast response (4 min), and good stability (up to 2 months). The analytical performance of the biosensor was comparable to the previously reported electrochemical biosensors for E. coli. As such, the approach of functionalization of graphene with 2-aminoterephthalic acid should be useful to allow the development of other similar sensing systems for other environmentally and clinically important analytes. Graphical abstractSchematic representation of the preparation and the function of an amino-functionalized graphene oxide (NH₂-GO) based impedimetric biosensor for the electrochemical detection of E. coli.

A disposable electrochemical sensor based on electrospinning of molecularly imprinted nanohybrid films for highly sensitive determination of the organotin acaricide cyhexatin

Nanofibrous polyporous membranes imprinted with cyhexatin (CYT) were formed via the ordered distribution of the imprints in electrospun nanofibers. The MIPs have a high mass transfer rate and enhanced adsorption capacity. In addition, a printed carbon electrode with enhanced sensitivity was developed via electrochemical fabrication of reduced graphene oxide (rGO) and gold nanoparticles (AuNPs). The molecularly imprinted sensor exhibits excellent selectivity and sensitivity for CYT. The structure and morphology of the nanohybrid films were characterized by using scanning electron microscopy, atomic force microscopy and chronoamperometry. The sensing performances were evaluated by cyclic voltammetry, differential pulse voltammetry and electrochemical impedance spectroscopy by using hexacyanoferrate(IV) as an electrochemical probe. The electrode, best operated at a working potential of around 0.16 V (vs. Ag/AgCl), has a linear response in the 1-800 ng mL^-1 CYT concentration range and a detection limit of 0.17 ng mL^-1 (at S/N = 3). The sensor demonstrated satisfactory recoveries when applied to the determination of CYT in spiked pear samples. Graphical abstract Schematic presentation of the electrochemical sensor for detection of CYT.

Extending the application of a magnetic PEG three-part drug release device on a graphene substrate for the removal of Gram-positive and Gram-negative bacteria and cancerous and pathologic cells

Objective

In this study, novel graphene oxide (GO)-based nanocomposites are presented. In fact, we have tried to replace the carboxyl groups on the surface of GO with amine groups to allow the biocompatible poly(ethylene glycol) bis(carboxymethyl) ether (average Mn 600) polymer to bond through an amide bond.

Materials and methods

The synthesis was conducted accurately according to final characterization experiments (Raman, X-ray diffraction [XRD], atomic force microscopy [AFM], X-ray photoelectron spectroscopy [XPS], thermogravimetric analysis [TGA], etc). The antimicrobial property of this nanocomposite was examined in Escherichia coli (ATCC 25922) as Gram-negative and Staphylococcus aureus (ATCC 25923) as Gram-positive bacterial species. Besides, curcumin (CUR) was added to the produced nanocomposite both as a promising anticancer drug and an antioxidant, the toxicity of which was then assessed on cellular-based HepG2 and pC12.

Results

An intense increase in toxicity was detected by MTT assay.

Conclusion

It can mainly be concluded that the nanocomposite synthesized in this study is capable of delivering drugs with antibacterial properties.

Surface Sizing Treated MWCNTs and Its Effect on the Wettability, Interfacial Interaction and Flexural Properties of MWCNT/Epoxy Nanocomposites

A surface-sizing technique was offered to take full advantage of multi-walled carbon nanotubes (MWCNTs) and epoxy resins. Two surface-sizing treated MWCNTs were obtained through a ball-milling treatment of amino-functionalized MWCNTs (MWCNT-NH₂) with n-butyl glycidylether (BuGE) and benzyl glycidylether (BeGE). These were referred to as MWCNT-BuGE and MWCNT-BeGE. The results indicated that the surface sizing effectively enhanced wettability, dispersibility of MWCNTs in the epoxy resin. These ameliorating effects, along with improved interfacial interaction between MWCNT-BeGE containing benzene rings and the epoxy matrix, which can offer a more efficient local load-transfer from matrix to MWCNTs, as observed by a higher G-band shift in Raman spectrum under bending loads than that of MWCNT-BuGE reinforced ones. Correspondingly, MWCNT-BeGE/epoxy nanocomposites exhibited increasing flexural strength and modulus of 22.9% and 37.8% respectively compared with the neat epoxy, and 7.3% and 7.7% respectively compared with MWCNT-BuGE/epoxy nanocomposites with the same MWCNT content.

One-pot synthesis of amine-functionalized graphene oxide by microwave-assisted reactions: an outstanding alternative for supporting materials in supercapacitors

A simple and straightforward method using microwave-assisted reactions is presented for the functionalization of graphene oxide with aromatic and non-aromatic amines, notedly dibenzylamine (DBA), p-phenylenediamine (PPD), diisopropylamine (DPA) and piperidine (PA). The as-synthesized amine-functionalized graphene oxide materials (amine-GO) were characterized using spectroscopic techniques including XRD, FTIR, ¹³C NMR, XPS, TEM for imaging and thermogravimetric analysis (TGA). The characterization confirmed the functionalization for all amines, reaching relatively high surface nitrogen atomic concentrations of up to 8.8%. The investigations of electrochemical behavior for the amine-GOs show the significant improvement in GO's electrochemical properties through amine functionalization, exhibiting long life cycle stability and reaching specific capacitance values of up to 290 F g⁻¹ and 260 F g⁻¹ for GO-PA and GO-DPA samples, respectively, confirming their potential application as alternative supporting materials in supercapacitors.

A simple and straightforward method using microwave-assisted reactions is presented for the functionalization of graphene oxide with aromatic and non-aromatic amines.

Anion selective pTSA doped polyaniline@graphene oxide-multiwalled carbon nanotube composite for Cr(VI) and Congo red adsorption

Multiwalled carbon nanotube (CNT)-graphene oxide (GO) composite was combined with polyaniline (Pani) using an oxidative polymerisation technique. The resulting Pani@GO-CNT was later doped with para toluene sulphonic acid (pTSA) to generate additional functionality. The functional groups exposed on the GO, Pani and pTSA were expected to impart a high degree of functionality to the pTSA-Pani@GO-CNT composite system. The composite was characterised by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. The characterisation results revealed the characteristics of Pani, GO, CNT, and pTSA, and suggested the successful formation of the pTSA-Pani@GO-CNT composite system. The composite was utilised successfully for the adsorptive removal of Cr(IV) and Congo red (CR) dye and the adsorption of both pollutants was found to be strongly dependent on the solution pH, adsorbate concentration, contact time, and reaction temperature. The maximum adsorption of Cr(IV) and CR was observed in an acidic medium at 30°C. The kinetics for Cr(IV) and CR adsorption was studied using pseudo-first order, pseudo-second order, and intraparticle diffusion models. The adsorption equilibrium data were also fitted to the Langmuir and Freundlich isotherm models. The thermodynamic results showed that the adsorption process was exothermic in nature. The present study provides a new methodology for the preparation of a highly functionalised Pani-based nanocomposite system and its potential applications to the adsorptive removal of a multicomponent pollutant system from an aqueous solution.

The effect of carbon nanotubes/NiFe2O4 on the thermal stability, combustion behavior and mechanical properties of unsaturated polyester resin

The incorporation of MWCNT@NiFe₂O₄ into the UPR matrix exhibit significant improvements in flame retardancy and mechanical properties, compared to that of pure UPR.

MEISENHEIMER COMPLEX BETWEEN 2,4,6-TRINITROTOLUENE AND 3-AMINOPROPYLTRIETHOXYSILANE AND ITS USE FOR A PAPER-BASED SENSOR

2,4,6-Trinitrotoluene (TNT) forms a red-colored Meisenheimer complex with 3-aminopropyltrenthoxysilane (APTES) both in solution and on solid phase. The TNT-APTES complex is unique since it forms yellow-colored complexes with 2,4,6-trinitrophenol and 4-nitrophenol, and no complex with 2,4-dinitrotoluene. The absorption spectrum of TNT-APTES has two absorption bands at 530 and 650 nm, while APTES complexes with 2,4,6-trinitrophenol and 4-nitrophenol have absorption maxima at around 420 nm, and no absorption change for 2,4-dinitrotoluene. The TNT-APTES complex facilitates the exchange of the TNT-CH3 proton/deuteron with solvent molecules. The red color of TNT-APTES is immediately visible at 1 µM of TNT.

Nanobioprobe mediated DNA aptamers for explosive detection

Specific nucleic acid aptamers using the microtiter plate based modified SELEX method against explosive trinitrotoluene are reported. Efficient partitioning of dsDNA was carried out using streptavidin labeled gold nanoprobes for the selection of specific aptamers. The selected binders having an affinity of ~10(-7) M were used in the newly developed electrochemical aptasensor, exhibiting a detection limit of around 1 ppb for trinitrotoluene.

Robust electrochemical analysis of As(III) integrating with interference tests: a case study in groundwater

In Togtoh region of Inner Mongolia, northern China, groundwater encountered high concentrations As contamination (greater than 50 μg L(-1)) causes an increasing concern. This work demonstrates an electrochemical protocol for robust (efficient and accurate) determination of As(III) in Togtoh water samples using Au microwire electrode without the need of pretreatment or clean-up steps. Considering the complicated conditions of Togtoh water, the efficiency of Au microwire electrode was systematically evaluated by a series of interference tests, stability and reproducibility measurements. No obvious interference on the determination of As(III) was observed. Especially, the influence of humic acid (HA) was intensively investigated. Electrode stability was also observed with long-term measurements (70 days) in Togtoh water solution and under different temperatures (0-35 °C). Excellent reproducibility (RSD:1.28%) was observed from different batches of Au microwire electrodes. The results obtained at Au microwire electrode were comparable to that obtained by inductively coupled plasma atomic emission spectroscopy (ICP-AES), indicating a good accuracy. These evaluations (efficiency, robustness, and accuracy) demonstrated that the Au microwire electrode was able to determine As(III) in application to real environmental samples.

Molybdenum disulfide nanoflower-chitosan-Au nanoparticles composites based electrochemical sensing platform for bisphenol A determination

Two-dimensional transition metal dichalcogenide are attracting increasing attention in electrochemical sensing due to their unique electronic properties. In this work, flower-like molybdenum disulfide (MoS2) was prepared by a simple hydrothermal method. The scanning electron microscopy and transmission electron microscopy images showed the MoS2 nanoflower had sizes with diameter of about 200nm and was constructed with many irregular sheets as a petal-like structure with thickness of several nanometers. A novel electrochemical sensor was constructed for the determination of bisphenol A (BPA) based on MoS2 and chitosan-gold nanoparticles composites modified electrode. The sensor showed an efficient electrocatalytic role for the oxidation of BPA, and the oxidation overpotentials of BPA decreased significantly and the peak current increased greatly compared with bare GCE and other modified electrode. A good linear relationship between the oxidation peak current and BPA concentration was obtained in the range from 0.05 to 100μM with a detection limit of 5.0×10(-9)M (S/N=3). The developed sensor exhibited high sensitivity and long-term stability, and it was successfully applied for the determination of BPA in different samples. This work indicated MoS2 nanoflowers were promising in electrochemical sensing and catalytic applications.