Fabrication of bimodal-pore SrTiO3 microspheres with excellent photocatalytic performance for Cr(VI) reduction under simulated sunlight

Efficient removal of Cr(VI) by a 3D Z-scheme TiO2-ZnxCd1-xS graphene aerogel via synergy of adsorption and photocatalysis under visible light

Efficient and robust photocatalysts for environmental pollutants removal with outstanding stability have great significance. Herein, we report a kind of three dimensional (3D) photocatalyst presented as Z-scheme heterojunction, which combining TiO₂ and Zn_xCd_1-xS with graphene aerogel to contrast TiO₂-Zn_xCd_1-xS graphene aerogel (TSGA, x=0.5) through a moderate hydrothermal process. The as-prepared Z-scheme TSGA was used to remove aqueous Cr(VI) via a synergistic effect of adsorption and visible light photocatalysis. The adsorption equilibrium can be reached about 40 min, then after about 30 min irradiation under visible light (wavelength (λ) > 420 nm) the removal rate of Cr(VI) almost reached 100%, which is much better than the performance of pristine TiO₂ and Zn_0.5Cd_0.5S, as well as TiO₂ graphene aerogel (TGA) and Zn_0.5Cd_0.5S graphene aerogel (SGA). The virulent Cr(VI) was reduced to Cr(III) with hypotoxicity after photocatalysis on TSGA, meanwhile the as-synthesized TSGA presented a good stability and reusability. The reduced graphene oxide (rGO) sheets between TiO₂ and Zn_0.5Cd_0.5S played a role as charge transfer mediator, promoting the photoinduced electrons transfer and photocatalysis ability of TSGA was enhanced significantly. Hence, such photocatalyst exhibits a potential application on removing heavy metals with high efficiency and stability from polluted aqueous environment.

High-efficiency Hg(II) adsorbent: FeS loaded on a carbon black from pyrolysis of waste tires and sequential reutilization as a photocatalyst

Iron-sulfur nano compounds have been proven to be effective in mercury removal, but the agglomeration, poor dispersion and mobility, and easy oxidation challenges limit their application. Herein, carbon black originating from pyrolysis of waste tires was used as a carrier of nano-FeS to obtain an efficient adsorbent (C@PDA-FeS). It is found that the C@PDA-FeS shows outstanding adsorption ability, excellent selectivity, and high removal rate. A maximum adsorption capacity of 1754 mg/g is obtained, and the residual Hg(II) ion concentration is as low as 3.2 μg/L in the simulated industrial wastewater, which meets the industrial discharge standard under the optimal conditions. Meanwhile, the removal rate of Hg(II) ion can reach 99.8% after up to 10 cycles. More importantly, the C@PDA-FeS still shows good adsorption efficiency, and the removal rate of Hg(II) ion is over 99% (25 mg/L Hg(II) concentration) after 90 days of storage, demonstrating the long-term stability and promising future of the adsorbent. In addition, the waste adsorbent (C@PDA-FeS/HgS) is reused as a photocatalyst to degrade methylene blue, and the corresponding degradation rate is 92.9% (10 mg/L).

Role of SrCO3 on Photocatalytic Performance of SrTiO3-SrCO3 Composites

Perovskites such as SrTiO3 are interesting for photocatalytic applications due to their structure-related and electronic properties. These properties are influenced by the presence of SrCO3 which is often formed simultaneously during the hydrothermal synthesis of SrTiO3. In this study, SrTiO3-SrCO3 composites with different contents of SrCO3 (5–24 wt%) were synthesized. Their morphological, structural, and optical properties were investigated using complementary methods such as scanning electron microscopy (SEM), X-ray diffraction (XRD), nitrogen sorption, and diffuse reflectance spectroscopy (DRS). Their photocatalytic activity was assessed during the degradation of diclofenac (DCFNa) in aqueous solution and CO2 photoreduction under Xe lamp irradiation. Improved photocatalytic efficiency in DCFNa degradation was observed for all the studied composites in comparison with SrTiO3, and the highest mineralization efficiency was obtained for the sample with 21 wt% SrCO3 content. The presence of SrCO3 led to an increased concentration of active species, such as •OH radicals. Otherwise, its presence inhibits CH4 and C2H6 production during CO2 photoreduction compared with pure SrTiO3.

Engineered magnetic oxides nanoparticles as efficient sorbents for wastewater remediation: a review

The rapid urbanization and industrialization is causing worldwide water pollution, calling for advanced cleaning methods. For instance, pollutant adsorption on magnetic oxides is efficient and very practical due to the easy separation from solutions by an magnetic field. Here we review the synthesis and performance of magnetic oxides such as iron oxides, spinel ferrites, and perovskite oxides for water remediation. We present structural, optical, and magnetic properties. Magnetic oxides are also promising photocatalysts for the degradation of organic pollutants. Antimicrobial activities and adsorption of heavy metals and radionucleides are also discussed.

Bi selectively doped SrTiO3-x nanosheets enhance photocatalytic CO2 reduction under visible light

Converting CO₂ into chemical energy by using solar energy is an environmental strategy to achieve carbon neutrality. In this paper, two dimensionality (2D) SrTiO_3-x nanosheets with oxygen vacancies were synthesized successfully. Oxygen vacancies will generate defect levels in the band structure of SrTiO_3-x. So, SrTiO_3-x nanosheets have good photocatalytic CO₂ reduction performance under visible light. In order to further improve its photocatalytic efficiency, Bi was used to dope Sr site and Ti site in SrTiO_3-x nanosheets respectively. It is found that Sr site is the adsorption site of CO₂ molecules. When Bi replaced Sr, CO₂ adsorption on the surface of SrTiO_3-x nanosheets was weakened. When Bi replaced Ti, there has no effect on CO₂ adsorption. Due to the synergistic effect of Bi doping, oxygen vacancies, and Sr active site, the 1.0% Bi-doped Ti site in SrTiO_3-x (1.0% Bi-Ti-STO) had the best photocatalytic performance under visible light (λ ≥ 420 nm). CO and CH₄ yields were 5.58 umol/g/h and 0.36 umol/g/h. Photocatalytic CO₂ reduction path has always been the focus of exploration. The in-situ FTIR spectrum proved the step of photocatalytic CO₂ reduction and COO- and COOH are important intermediates in the photocatalytic CO₂ reaction.

Photocatalytic overall water splitting without noble-metal: Decorating CoP on Al-doped SrTiO3

CoP, a noble-metal-free cocatalyst, was first introduced onto the surface of Al-doped SrTiO₃ (Al:STO) via an in situ photodeposition-phosphorization method for photocatalytic overall water splitting (POWS) into stoichiometric H₂ and O₂. Compared with pure Al:STO, the POWS activity was enhanced by a factor of ~ 421 over 1.0%CoP/Al:STO, with the highest evolution rates of 2106 and 1002 μmol h^-1 g^-1 for H₂ and O₂, respectively. The mechanism for the remarkably boosted POWS activity was systematically analyzed based on the comprehensive characterization. On the one hand, benefiting from the in situ photodeposition process, CoP with metallic character were intimately decorated onto the surface of Al:STO and accelerated the separation and migration of photoinduced charge carriers. On the other hand, CoP, serving as reactive sites for H₂ evolution reaction, lowered the overpotential and facilitated the surface reduction reaction, thereby enhancing the POWS activity. Furthermore, Cr₂O₃ was photodeposited on the surface of 1.0%CoP/Al:STO composite to suppress the undesired reverse reaction and the POWS activity was further enhanced up to 3558 and 1722 μmol h^-1 g^-1 for H₂ and O₂, respectively, with apparent quantum yield of 7.1% at 350 ± 10 nm. This work presents a new avenue for designing POWS system without noble-metal cocatalyst.

Manipulating the Structure and Characterization of Sr1−xLaxTiO3 Nanocubes toward the Photodegradation of 2-Naphthol under Artificial Solar Light

Effective La-doped SrTiO3 (Sr1−xLaxTiO3, x = 0–0.1 mol.% La-doped) nanocubes were successfully synthesized by a hydrothermal method. The influence of different La dopant concentrations on the physicochemical properties of the host structure of SrTiO3 was fully characterized. X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) revealed that the Sr2+ in the crystal lattice of SrTiO3 was substituted by La3+. As a result, the absorption region of the Sr1−xLaxTiO3 could be extended to visible light. Scanning electron microscopy (SEM) images confirmed that their morphologies are associated with an increased surface area and an increased La-doping concentration. The decrease in the photoluminescence (PL) intensity of the dopant samples showed more defect levels created by the dopant La+3 cations in the SrTiO3 structure. The photocatalytic activities of Sr1−xLaxTiO3 were evaluated with regard to the degradation of 2-naphthol at typical conditions under artificial solar light. Among the candidates, Sr0.95La0.05TiO3 exhibited the highest photocatalytic performance for the degradation of 2-naphthol, which reached 92% degradation efficiency, corresponding to a 0.0196 min−1 degradation rate constant, within 180 minutes of irradiation. Manipulating the structure of Sr1−xLaxTiO3 nanocubes could produce a more effective and stable degradation efficiency than their parent compound, SrTiO3. The parameters remarkably influence the Sr1−xLaxTiO3 nanocubes’ structure, and their degradation efficiencies were also studied. Undoubtedly, substantial breakthroughs of Sr1−xLaxTiO3 nanocube photocatalysts toward the treatment of organic contaminants from industrial wastewater are expected shortly.

Fabrication of MOF-derived tubular In2O3@SnIn4S8 hybrid: Heterojunction formation and promoted photocatalytic reduction of Cr(VI) under visible light

Tubular In₂O₃@SnIn₄S₈ hierarchical hybrid photocatalyst was firstly fabricated by a two-step method. The morphology and composition were characterized by scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), and X-ray diffraction (XRD). The XRD results show that the obtained In₂O₃ microtubes were highly crystallized, while the SnIn₄S₈ flakes prepared at low temperature were poorly crystallized. The SEM image of the hybrid shows that numerous SnIn₄S₈ nanoflakes were assembled over the surface of In₂O₃ microtubes. In₂O₃ served as dispersing-templates have reduced the agglomeration of SnIn₄S₈ flakes. Meanwhile, the heterojunctions formed at the interfaces between In₂O₃ and SnIn₄S₈ could facilitate the interfacial charge transfer, as well as promote the photocatalytic activity of the hybrid. In the treatment of Cr(VI)-containing wastewater, the In₂O₃@SnIn₄S₈ hybrid not only exhibited strong adsorption ability, but also showed remarkably enhanced photocatalytic activity compared with pure SnIn₄S₈. The photocatalytic reaction constant k for In₂O₃@SnIn₄S₈ was approximately 2.54 times higher than that of SnIn₄S₈. The efficient activity of this hybrid photocatalyst should be ascribed to the promoted separation efficiency of electron/hole pairs, which was proved by the following three-dimensional excitation-emission matrix fluorescence spectra (3D EEMs), photocurrent responds, and EIS characterizations.

An eco-friendly low-temperature synthetic approach towards micro-pebble-structured GO@SrTiO3 nanocomposites for the detection of 2,4,6-trichlorophenol in environmental samples

The low-temperature synthesis of the graphene oxide-wrapped perovskite-type strontium titanate nanocomposites (GO@SrTiO₃-NC) is reported for the electrochemical sensing of organochlorine pesticide 2,4,6-trichlorophenol (TCP) detection. The as-prepared GO@SrTiO₃ nanocomposites provide a large surface area, excellent conductivity, and active sites, which are more favorable to the catalysis of TCP. The synergistic effect between the GO and the perovskite SrTiO₃ results in the extended working range of 0.01 to 1.47 and 1.47 to 434.4 μM with a very low detection limit of 3.21 nM towards TCP detection. Moreover, the prepared sensor possessed good selectivity and long-term stability. Finally, the practical applicability of the sensor was tested in environmental samples of river water and soil, exhibiting adequate recovery values.

Synthesis of hydroxide-enriched cerium-doped oxy-sulfide catalyst for visible light-assisted reduction of Cr(vi)

Semiconductor catalysts are significantly attractive materials for different cutting-edge applications, including the detoxification of toxic pollutants.

Recent advances in surface and interface design of photocatalysts for the degradation of volatile organic compounds

Photocatalysis has attracted wide attention in eliminating volatile organic compounds (VOCs). This paper pays attention to the relationship between structure and performance of photocatalysts based on the fact that catalytic reactions arise on the surface of catalysts and the interface structure of photocatalysts plays key role in transfer efficiency of charges carriers. This review summarizes various surface/interface designs including unsaturated coordination such as oxygen vacancies, surface halogenations, and heterojunctions, homojunctions, facets, etc., as well as the application in photocatalytic degradation of VOCs. This paper reviews the influence of surface and interface properties of materials on VOCs molecules, effective strategies to promote the decomposition of VOCs from the perspectives of VOCs activation, reaction barrier etc., and presents various methods of photocatalyst design appropriately. The degradation path of highly toxic benzene VOCs are also summarized. In addition, the possible problems and suggestions for photocatalytic degradation of VOCs are proposed.

Enhanced Visible-Light Photocatalytic Activity of Ag QDs Anchored on CeO2 Nanosheets with a Carbon Coating

Ag quantum dots (QDs) anchored on CeO2 nanosheets with a carbon coating (Ag/CeO2@C) (composites) were prepared via an in situ reduction approach for the photocatalytic degradation of Cr(VI) and tetracycline hydrochloride (TCH) in the visible-light region. The photocatalytic activity of Ag/CeO2@C was greatly affected by carbon content, Ag-doping content, Cr(VI) concentration, pH value, and inorganic ions. Enhanced photocatalytic activity was obtained by Ag/CeO2@C (compared to CeO2 and CeO2@C), of which 3-Ag/CeO2@C-2 with an Ag-doping content of 5.41% presented the best removal efficiency and the most superior stability after five cycles. ·O2- and ·OH radicals were crucial for the photocatalytic capacity of 3-Ag/CeO2@C-2. The combined effect of the surface plasma resonance (SPR) of Ag QDs, an electron trapper of carbon shells, and the redox activity of the Ce(III)/Ce(IV) coupling induced efficient charge transfer and separation, suppressing the recombination of electron-hole pairs.

A novel n-type CdS nanorods/p-type LaFeO3 heterojunction nanocomposite with enhanced visible-light photocatalytic performance

In this work, a novel n-type CdS nanorods/p-type LaFeO3 (CdS NRs/LFO) nanocomposite was prepared, for the first time, via a facile solvothermal method. The as-prepared n-CdS NRs/p-LFO nanocomposite was characterized by using powder X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HR-TEM), energy-dispersive X-ray spectroscopy (EDX), UV-visible diffuse reflection spectroscopy (DRS), vibrating sample magnetometry (VSM), photoluminescence (PL) spectroscopy, and Brunauer-Emmett-Teller (BET) surface area analysis. All data revealed the attachment of the LFO nanoparticle on the surface of CdS NRs. This novel nanocomposite was applied as a novel visible light photocatalyst for the degradation of methylene blue (MB), rhodamine B (RhB) and methyl orange (MO) dyes under visible-light irradiation. Under optimized conditions, the degradation efficiency was 97.5% for MB, 80% for RhB and 85% for MO in the presence of H2O2 and over CdS NRs/LFO nanocomposite. The photocatalytic activity of CdS NRs/LFO was almost 16 and 8 times as high as those of the pristine CdS NRs and pure LFO, respectively. The photocatalytic activity was enhanced mainly due to the high efficiency in separation of electron-hole pairs induced by the remarkable synergistic effects of CdS and LFO semiconductors. After the photocatalytic reaction, the nanocomposite can be easily separated from the reaction solution and reused several times without loss of its photocatalytic activity. Trapping experiments indicated that ·OH radicals were the main reactive species for dye degradation in the present photocatalytic system. On the basis of the experimental results and estimated energy band positions, the mechanism for the enhanced photocatalytic activity was proposed.

Self-Assembled Single-Crystalline GaN Having a Bimodal Meso/Macropore Structure To Enhance Photoabsorption and Photocatalytic Reactions

This paper describes the self-assembled fabrication of single-crystal GaN with a bimodal pore (meso/macropore) size distribution (BiPS-GaN). A 4.7 μm-thick BiPS-GaN layer was grown spontaneously using halogen-free vapor phase epitaxy in conjunction with boron impurity doping (>1 × 10¹⁹ atoms/cm³) on a GaN template fabricated via metalorganic chemical vapor deposition (MOCVD-GaN). The boron impurity acted as a surfactant, and its segregation generated a dense (>1 × 10¹⁰ cm^-2), homogeneous distribution of mesopores with sizes of 30-40 nm in GaN during growth. In addition, macropores with sizes of 0.1-2 μm were produced by the fusion of mesopores in close proximity to one another. As a result, BiPS-GaN exhibited a high density of both meso- and macropores, all aligned in the vertical direction (that is, along the c axis). BiPS-GaN showed good electroconductivity and almost the same high degree of crystallinity as the MOCVD-GaN template. Furthermore, the hybrid meso/macropore structure of BiPS-GaN imparted excellent photoabsorption properties and allowed this material to work as an efficient support for a nanosized IrO _x catalyst. The photocurrent density in BiPS-GaN was enhanced by as much as a factor of 5 compared to planar GaN by effective absorption due to the hybrid meso/macropore structure of BiPS-GaN. Moreover, the oxygen generation efficiency of BiPS-GaN with the IrO _x catalyst was approximately doubled, compared to that of BiPS-GaN without IrO _x, while maintaining long-term stability. These results demonstrate that BiPS-GaN fabricated in this facile manner has significant potential in applications such as photoelectrochemical reactions and catalysis.

Removing Cr (VI) in water via visible-light photocatalytic reduction over Cr-doped SrTiO3 nanoplates

It is crucial to develop a high-efficiency visible-light responsive photocatalyst for settling the increasing contamination stemmed from toxic heavy metal ions in wastewater. In this study, Cr-doped SrTiO₃ (CrSTO) nanoplates were synthesized by a facile one-pot solvothermal method with ethylene glycol as both the solvent and morphology controller. The resultant CrSTO nanoplates are about 100 nm in size and 20 nm in thickness, which are composed of SrTiO₃ nanocrystals about 19 nm in diameter. Furthermore, they possess the mesopore 3.0 nm in size, endowing their much higher specific surface area than the commercial SrTiO₃ particles. The Cr element is doped into the crystal lattice of SrTiO₃ by the substitution of Cr³⁺ for Sr²⁺, which enables the absorption edge redshift to the visible light region, thus elevating the visible-light absorption capability. In addition, the CrSTO-0.9 nanoplate with 0.9% Cr element content exhibits the highest photocatalytic performance for the Cr(VI) reduction under visible light irradiation, which can reduce nearly all Cr(VI) within 3.5 h and preserve the excellent stability after six recycles. This kind of CrSTO nanoplates may serve as a potential and promising photocatalyst for efficient Cr(VI) removal in wastewater.

Facile fabrication of sponge-like hierarchically porous Ni,La–SrTiO3 templated by in situ generated carbon deposits and the enhanced visible-light photocatalytic activity

Hierarchical pore-induced multiple internal reflections and/or scattering of light improves the capability of light trapping and thus photocatalytic efficiency.

High-Performance Photocatalytic Hydrogen Production and Degradation of Levofloxacin by Wide Spectrum-Responsive Ag/Fe3O4 Bridged SrTiO3/g-C3N4 Plasmonic Nanojunctions: Joint Effect of Ag and Fe3O4

Highly photoresponsive semiconductor photocatalysis for energy and environmental applications require judicious choice and optimization of semiconductor interfaces for wide spectral capabilities. This work aims at rational designing of highly active SrTiO₃/g-C₃N₄ junctions bridged with Ag/Fe₃O₄ nanoparticles for utilizing Z-scheme transfer and surface plasmon resonance effect of Ag augmented by iron oxide. The SrTiO₃/(Ag/Fe₃O₄)/g-C₃N₄ (SFC) catalyst was employed for photocatalytic hydrogen production and photodegradation of levofloxacin (LFC; 20 mg/L) under UV, visible, near infra-red, and natural solar light exhibiting high performance. Under visible light (<780 nm), SFC-3 sample (30 wt % g-C₃N₄ and 3% Ag/Fe₃O₄) shows a H₂ evolution of 2008 μmol g^-1 h^-1 which is ∼14 times that of bare g-C₃N₄. In addition, 99.3% removal of LFC was degraded in 90 min under visible light with retention of activity under sun. The inherent topological properties, complete, higher charge separation, and reduced recombination allowed this catalyst for a high photocatalytic response which was proved by UV-diffuse reflectance spectroscopy, photoluminescence, electrochemical impedance spectroscopy, and photocurrent response measurements. Scavenging experiments and electron spin resonance analysis reveal that the mechanism shifts from a dual charge transfer in case of binary junction to essential Z-scheme with incorporation of Ag/Fe₃O₄. Both ^•O₂^- and ^•OH are main active radicals in visible light, whereas ^•O₂^- majorly participate under UV. The synergistic effect of SrTiO₃, g-C₃N₄, and plasmon resonance of Ag/Fe₃O₄ not only improves light response and reduce recombination but also enhances the redox-ability of charge carriers. A H₂ production mechanism and LFC degradation pathway (degradation, defluorination, and hydrolysis) has been predicted. This work paves a way for development of photocatalysts working in practical conditions for pollution and energy issues.

Photocatalytic reduction of Cr (VI) on nano-sized red phosphorus under visible light irradiation

Red phosphorus as a novel visible-light-responsive and metal-free photocatalyst has attracted extensive attention in the area of energy conversion and environmental remediation. Herein, nano-sized red phosphorus photocatalyst was synthesized via a hydrothermal and ultrasonic method and used for reduction of Cr (VI) for the first time. The as-prepared photocatalysts were characterized by XRD, UV-Vis-DRS, XPS, SEM, TEM and photoelectrochemical measurements. Compared to bulk red phosphorus, nano-sized red phosphorus exhibit a significantly enhanced photocatalytic activity for reduction of Cr (VI) due to the greatly reduced charge transfer resistance and enhanced adsorption capability of Cr (VI).

Fabrication and photocatalytic property of magnetic SrTiO3/NiFe2O4 heterojunction nanocomposites

Novel multifunctional SrTiO3/NiFe2O4 nanocomposites were successfully fabricated via a two-step route. The as-prepared samples were characterized by using X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), field-emission transmission electron microscopy (TEM), UV-visible diffuse reflectance spectroscopy (DRS), X-ray photoelectron spectroscopy (XPS), photoluminescence (PL) spectroscopy and vibrating sample magnetometry (VSM). The results indicate that the SrTiO3/NiFe2O4 heterostructures are composed of SrTiO3 spheroidal nanoparticles adhered to NiFe2O4 polyhedra. The heterojunction established in the composite material accelerates the process of electron-hole pair separation and boosts the photo-Fenton reaction. Among the samples, 15 wt% SrTiO3/NiFe2O4 nanocomposites exhibit a powerful light response and excellent room temperature ferromagnetism. Subsequently, the photocatalytic degradation of RhB over the as-prepared samples was investigated and optimized, revealing that the 15 wt% SrTiO3/NiFe2O4 nanocomposites exhibit the best photocatalytic activity and stability under simulated solar light irradiation. Furthermore, according to experimental results, the possible mechanism of improved photocatalytic activity was also proposed.

Fabrication uniform hollow Bi2S3 nanospheres via Kirkendall effect for photocatalytic reduction of Cr(VI) in electroplating industry wastewater

Hazardous hexavalent chromium removal from wastewater is an urgent issue in industry environmental pollution. In this work, hollow Bi₂S₃ nanospheres have been successfully synthesized from unique Bi₂O₃ porous nanospheres via Kirkendall effect through hydrothermal process. It was found that the sulfur source and the initial Bi₂O₃ templates played key roles in the formation of the uniform morphologies and structures through an anion exchange process. Compared with other Bi₂S₃ samples, the synthesized hollow Bi₂S₃ nanospheres exhibited much enhanced photocatalytic ability for Cr(VI) photoreduction. XPS analysis demonstrated that Cr(VI) was reduced to less harmful Cr(III) species over hollow Bi₂S₃ nanospheres under visible-light irradiation. More importantly, the hollow Bi₂S₃ nanospheres remained high efficiency and good stability in the recycling Cr(VI) photoreduction, and exhibited remarkable Cr(VI) removal ability in actual electroplating industry wastewater treatment.