A comprehensive study on photocatalytic activity of supported Ni/Pb sulfide and oxide systems onto natural zeolite nanoparticles

Photocatalytic degradation of 2,4-dichlorophenol using nanomaterials silver halide catalysts

In this study, the photocatalytic activity of nanomaterials Ag/AgX (X = Cl, Br, I) is reported. Highly efficient silver halide (Ag/AgX where X = Cl, Br, I) photocatalysts were synthesized through a hydrothermal method. The samples were characterized using a range of techniques such as X-ray diffraction (XRD), scanning electron microscopy (SEM), and Brunauer-Emmett-Teller (BET) to check their structural, morphology, textural and optical properties. In addition, the photocatalytic activity of photocatalysts was evaluated through the degradation of 2,4-dichlorophenol (2,4-DCP) under UV and visible light irradiation. XRD analysis confirmed the presence of a single-phase structure (pure phase) in the synthesized photocatalysts. SEM micrographs showed agglomeration with a non-uniform distribution of particles, which is a characteristic of surfactant-free precipitation reactions in aqueous media. The Ag/AgBr photocatalyst exhibited the best degradation efficiency, resulting in 83.37% and 89.39% photodegradation after 5 h of UV and visible light irradiation, respectively. The effect of catalyst loading, initial solution pH, and 2,4-DCP concentration was investigated for the best-performing Ag/AgBr photocatalyst. The degradation kinetics were best described by the pseudo-first-order Langmuir-Hinshelwood model. The photocatalytic capacity of Ag/AgBr decreased by 50% after five reuse cycles. SEM images revealed heightened levels of photodegradation on the catalyst surface. The study proved the feasibility of using simple synthesis methods to produce visible light active photocatalysts capable of degrading refractory phenolic pollutants in aqueous systems.

Green photocatalytic remediation of Fenthion using composites with natural red clay and non-toxic metal oxides with visible light irradiation

In the present work, composites with non-toxic metal oxides, such as TiO₂ and ZnO, and a natural red clay (taua) reach in hematite were used in the photocatalytic degradation of Fenthion. The composite TiO₂/Taua (0.5:1 wt. ratio) and pure TiO₂ were prepared by sol-gel method while ZnO/Taua (0.5:1 wt. ratio) and pure ZnO were prepared by Pechini method. The materials were characterized by XRD, SEM, EDX, and DRS. The anatase phase was formed in both pure TiO₂ and TiO₂/Taua, while the hexagonal phase was formed in pure ZnO and ZnO/Taua. The bandgap energies for the two composites were narrowed compared to the respective pure oxides as consequence of the hematite (α-Fe₂O₃, E_g = 2.1 eV) in the red clay, reaching 2.1 eV for TiO₂/Taua and 2.0 eV for ZnO/Taua, while the bandgap energies for pure TiO₂ and ZnO were 3.2 and 3.0 eV, respectively. Fenthion was not degraded in the dark, but the concentration droped 20% after 180 min under visible light irradiation without photocatalyst and 60% after 210 min in the presence of the pure red clay. Both TiO₂/Taua and ZnO/Taua composites were also photocatalytic active to degrade Fenthion (λ > 420 nm), with degradation of 78% (in 180 min) and 85% (in 210 min) respectively. In the optimized conditions (pH 2, 100 mg L^-1 of H₂O₂ and 30 mg L^-1 of Fenthion), the ZnO/Taua composite was the most efficient, reaching 89% degradation in up to 30 min, with Fenthion sulfoxide as the degradation product.

Microbe-mediated transformation of metal sulfides: Mechanisms and environmental significance

Microorganisms play a key role in the natural circulation of various constituent elements of metal sulfides. Some microorganisms (such as Thiobacillus ferrooxidans) can promote the oxidation of metal sulfides to increase the release of heavy metals. However, other microorganisms (such as Desulfovibrio vulgaris) can transform heavy metals into metal sulfides crystals. Therefore, insight into the metal sulfides transformation mediated by microorganisms is of great significance to environmental protection. In this review, first, we discuss the mechanism and influencing factors of microorganisms transforming heavy metals into metal sulfides crystals in different environments. Then, we explore three microbe-mediated transformation forms of heavy metals to metal sulfides and their environmental applications: (1) transformation to metal sulfides precipitation for metal resource recovery; (2) transformation to metal sulfides nanoparticles (NPs) for pollutant treatment; (3) transformation to "metal sulfides-microbe" biohybrid system for clean energy production and pollutant remediation. Finally, we further provide critical views on the application of microbe-mediated metal sulfides transformation in the environmental field and discuss the need for future research.

Applications of Nano-Zeolite in Wastewater Treatment: An Overview

Nano-zeolite is an innovative class of materials that received recognition for its potential use in water and tertiary wastewater treatment. These applications include ion-exchange/sorption, photo-degradation, and membrane separation. The aim of this work is to summarize and analyze the current knowledge about the utilization of nano-zeolite in these applications, identify the gaps in this field, and highlight the challenges that face the wide scale applications of these materials. Within this context, an introduction to water quality, water and wastewater treatment, utilization of zeolite in contaminant removal from water was addressed and linked to its structure and the advances in zeolite preparation techniques were overviewed. To have insights into the trends of the scientific interest in this field, an in-depth analysis of the variation in annual research distribution over the last decade was performed for each application. This analysis covered the research that addressed the potential use of both zeolites and nano-zeolites. For each application, the characterization, experimental testing schemes, and theoretical analysis methodologies were overviewed. The results of the most advanced research were collected, summarized, and analyzed to allow an easy visualization and comparison of these research results. Finally, the gaps and challenges that face these applications are concluded.

A State-of-the-Art Review on Innovative Geopolymer Composites Designed for Water and Wastewater Treatment

There is nothing more fundamental than clean potable water for living beings next to air. On the other hand, wastewater management is cropping up as a challenging task day-by-day due to lots of new additions of novel pollutants as well as the development of infrastructures and regulations that could not maintain its pace with the burgeoning escalation of populace and urbanizations. Therefore, momentous approaches must be sought-after to reclaim fresh water from wastewaters in order to address this great societal challenge. One of the routes is to clean wastewater through treatment processes using diverse adsorbents. However, most of them are unsustainable and quite costly e.g. activated carbon adsorbents, etc. Quite recently, innovative, sustainable, durable, affordable, user and eco-benevolent Geopolymer composites have been brought into play to serve the purpose as a pretty novel subject matter since they can be manufactured by a simple process of Geopolymerization at low temperature, lower energy with mitigated carbon footprints and marvellously, exhibit outstanding properties of physical and chemical stability, ion-exchange, dielectric characteristics, etc., with a porous structure and of course lucrative too because of the incorporation of wastes with them, which is in harmony with the goal to transit from linear to circular economy, i.e., "one's waste is the treasure for another". For these reasons, nowadays, this ground-breaking inorganic class of amorphous alumina-silicate materials are drawing the attention of the world researchers for designing them as adsorbents for water and wastewater treatment where the chemical nature and structure of the materials have a great impact on their adsorption competence. The aim of the current most recent state-of-the-art and scientometric review is to comprehend and assess thoroughly the advancements in geo-synthesis, properties and applications of geopolymer composites designed for the elimination of hazardous contaminants viz., heavy metal ions, dyes, etc. The adsorption mechanisms and effects of various environmental conditions on adsorption efficiency are also taken into account for review of the importance of Geopolymers as most recent adsorbents to get rid of the death-defying and toxic pollutants from wastewater with a view to obtaining reclaimed potable and sparkling water for reuse offering to trim down the massive crisis of scarcity of water promoting sustainable water and wastewater treatment for greener environments. The appraisal is made on the performance estimation of Geopolymers for water and wastewater treatment along with the three-dimensional printed components are characterized for mechanical, physical and chemical attributes, permeability and Ammonium (NH4+) ion removal competence of Geopolymer composites as alternative adsorbents for sequestration of an assortment of contaminants during wastewater treatment.

Supported cuprous oxide-clinoptilolite nanoparticles: Brief identification and the catalytic kinetics in the photodegradation of dichloroaniline

The supported CuO onto the ball-mill prepared clinoptilolite nanoparticles (CNPs) was prepared via an ion exchange process in Cu(II) aqueous solution followed by the calcination process. The CuO-CNP samples with various CuO loading were briefly characterized by XRD, FTIR, and DRS. pHpzc was varied in the range of 6.3 to 6.8 depending on the amount of loaded CuO in the samples. The band gap energy was estimated by applying the Kubelka-Munk equation on the DRS results that varied from 2.41 to 2.50 eV depending on the CuO loading. Based on the Scherrer equation nano-sized CuO-CNP at about 50 nm was estimated. The CuO-CNP contained 3.9% CuO showed the highest photocatalytic activity toward dichloroaniline (DCA). The effects of the experimental variables on DCA photodegradation were studied by using the Hinshelwood model. The optimal conditions for obtaining a higher rate for DCA photodegradation were the catalyst dose of 0.5 g/L, C_DCA: 5 ppm, and the initial pH: 3. HPLC analysis of the photodegraded DCA solutions for 180 and 300 min gave the degradation extents 71% and 90%, respectively.

Photocatalytic kinetics of 2,4-dichloroaniline degradation by NiO-clinoptilolite nanoparticles

The ball-mill clinoptilolite nanoparticles (CNP) was ion-exchanged in Ni(II) solutions and calcined to obtain NiO-CNP catalysts with various NiO loadings. The resultant CNP was ion-exchanged in 0.1, 0.2, 0.3, and 0.4 M Ni(II) solutions and then calcined at 450 °C. The resultant NiO-CNPs contained 1.9, 2.3, 3.0, and 3.2% NiO, respectively. The XRD, FTIR, and DRS characterization techniques were applied. By applying the Scherrer equation on the XRD results, the average crystallite size for the NiO-CNP samples was estimated in the range of 42-65 nm. The pHpzc of the NiO-CNP species was slightly changed from 6.8 to 7.6 by an increase in the loaded NiO. The band gap energy of the samples was calculated by applying the Kubelka-Munk equation on the DRS results. The band gap energies of 3.81, 4.05, and 3.63 eV were estimated for the direct electronic transitions of the CN2, CN2.3, and CN3.2 samples, respectively. The boosted photoactivity was obtained in 2,4-dichloroanilyne (DCA) degradation when NiO supported onto both micronized clinoptilolite and its nanoparticles. The effects of the most important experimental variables on DCA photodegradation rate were kinetically studied by applying the Hinshelwood model on the results. The faster rate for the DCA photodegradation was achieved at the optimal conditions, including the catalyst dose: 0.5 g/L, C_DCA: 5 ppm, and the initial pH: 3. Some new peaks were observed in the HPLC chromatograms for the photodegraded DCA solutions after 180 min and 300 min, which showed 84% and 95% DCA photodegradation.

Cadmium sulfide quantum dots/dodecahedral polyoxometalates/oxygen-doped mesoporous graphite carbon nitride with Z-scheme and Type-II as tandem heterojunctions for boosting visible-light-driven photocatalytic performance

It is known that fabrication of tandem heterojunctions between different types of heterojunctions can promote the charge separation. Herein, novel cadmium sulfide quantum dots (CdS QDs)/dodecahedral phosphotungstic acid potassium K₃PW₁₂O₄₀ (KPW)/oxygen-doped mesoporous graphite carbon nitride (meso-g-C₃N₄) nanosheets tandem heterojunctions are prepared by the hydrothermal method combined with direct template calcination and in-situ chemical sedimentation strategy. The results show that tandem heterojunctions formed by the Z-Scheme heterojunction between CdS QDs and KPW and the type-II heterojunction between CdS QDs and meso-g-C₃N₄ can extend the optical response into visible light region. Importantly, under visible light irradiation, photocatalytic hydrogen production rate and photocatalytic Cr⁶⁺ removal rate over CdS/KPW/meso-g-C₃N₄ is higher than that of KPW and CdS/KPW. This remarkable photocatalytic performance is due to the effective charge separation and transfer of the special tandem heterojunction structure. This novel tandem heterojunction will offer new insights for fabricating other high-performance photocatalytic systems.

Utilization of rice husk and waste aluminum cans for the synthesis of some nanosized zeolite, zeolite/zeolite, and geopolymer/zeolite products for the efficient removal of Co(II), Cu(II), and Zn(II) ions from aqueous media

In this paper, rice husk and waste aluminum cans were exploited as silicon and aluminum sources, respectively for the low-cost synthesis of some nanosized zeolite, zeolite/zeolite, and geopolymer/zeolite products. XRD confirmed that the synthesized geopolymer/zeolite products are geopolymer/zeolite A (has a crystallite size of 58.44 nm & abbreviated as G1) and geopolymer/faujasite (has a crystallite size of 25.58 and 20.26 nm & abbreviated as G2 and G3, respectively). Also, the synthesized zeolite products are sodium aluminum silicate hydrate (has a crystallite size of 27.65 and 41.85 nm & abbreviated as H1 and H2, respectively). Besides, the synthesized zeolite/zeolite product is sodium aluminum silicate hydrate/zeolite A (has a crystallite size of 66.01 nm and abbreviated as H3). Moreover, the synthesized products were characterized using other tools such as HR-TEM, FE-SEM, EDX, and FT-IR. The synthesized products were efficiently applied for removing Co(II), Cu(II), and Zn(II) ions from aqueous media and wastewater which was taken from Abuzaabal- Qalyubiyah-Egypt. The maximum uptake capacity of G3 sample toward Co(II), Cu(II), and Zn(II) ions is 134.24 ± 1.26, 126.26 ± 0.32, and 131.93 ± 0.87 mg/g, respectively. The uptake of the studied metal ions is spontaneous, chemical, exothermic, and fitted well with the Langmuir isotherm and pseudo-2nd-order kinetic model.

BiVO4/WO3 nano-composite: characterization and designing the experiments in photodegradation of sulfasalazine

A BiVO₄-WO₃ nano-composite (NC) was hydrothermally prepared and characterized by different techniques including X-ray diffraction (XRD), scanning electron microscope equipped with an energy-dispersive X-ray (EDX) analyzer, X-ray mapping, UV-Vis reflectance spectroscopy (DRS), and photoluminescence spectroscopy (PL). The average crystallite size of 8.5 nm was estimated for the composite by the Williamson-Hall equation. The band gap energies of 2.46, 3.02, and 2.95 eV were obtained for the direct electronic transitions of BiVO₄, WO₃, and the composite, respectively. The point of zero charges (pHpzc) of the composite was also estimated at 5. The composite was then used in the photodegradation of sulfasalazine (SSZ). When the moles of WO₃ was four times greater than BiVO₄, the best photocatalytic activity and the lowest PL intensity were obtained. The simultaneous effects of the experimental variables on the boosted photocatalytic activity of the composite (to the single semiconductors) were studied by the response surface methodology (RSM). A significant quadratic model was confirmed for processing the data based on the F value of a model F value of 63.55 > F_{0.05, 14, 13} = 2.55. This was also confirmed by LOF F value of 2.56 < F_{0.05, 10, 3} = 8.79. Besides, the multiple correlation coefficients R² (R² = 0.9856), adjusted R² (adj-R² = 0.9701), and predicted R² (pred-R² = 0.9098) confirm the goodness of the model. The optimal run included C_SSZ 9 mg/L, pH 4, 40 min irradiation time, and 0.8 g/L of the composite under the visible light irradiation.

Efficient recovery of Cu(II) by LTA-zeolites with hierarchical pores and their resource utilization in electrochemical denitrification: Environmentally friendly design and reutilization of waste in water

Water pollution seriously endangers human health and the environment. Here we prepared and tested mesoporous LTA zeolites for the adsorption of Cu(II) from aqueous media and the captured copper was further used for electrochemical nitrate reduction. The prepared hierarchically porous LTA exhibited a high capacity (341.5 mg g^-1) for Cu(II) adsorption, following the pseudo-second-order kinetic and Freundlich adsorption isotherm models well. The Cu-LTA sample was characterised by various analytical methods, and Cu(I) species were identified as the active sites for nitrate electrochemical reduction. Based on the spectral characterization and reducibility, strong metal-support interaction was found between copper and LTA, which is beneficial to the dispersion of active sites and their contacts with nitrates. In total, 10.1 g-N-NO₃ g^-1-Cu was reduced over the Cu-LTA-modified cathode in a three-electrode system with high N₂ selectivity (92.1 %). Compared to purely microporous zeolites, mesoporous LTA has a higher capacity for Cu(II) removal and nitrate reduction. The mesoporous structure allows easy access to the inner active sites with low diffusion resistance. The low Tafel slope and high current density confirm the high activity of the mesoporous Cu-LTA, making it a promising and efficient material for the removal and reuse of heavy metal ions.

Recent Advances in Functionalized Mesoporous Silica Frameworks for Efficient Desulfurization of Fuels

Considerable health and climate benefits arising from the use of low-sulfur fuels has propelled the research on desulfurization of fossil fuels. Ideal fuels are urgently needed and are expected to be ultra-low in sulfur (10-15 ppm), with no greater than 50 ppm sulfur content. Although several sulfur removal techniques are available in refineries and petrochemical units, their high operational costs, complex operational needs, low efficiencies, and higher environmental risks render them unviable and challenging to implement. In recent years, mesoporous silica-based materials have emerged as promising desulfurizing agents, owing to their high porosity, high surface area, and easier functionalization compared to conventional materials. In this review, we report on recent progress in the synthesis and chemistry of new functionalized mesoporous silica materials aiming to lower the sulfur content of fuels. Additionally, we discuss the role of special active sites in these sorbent materials and investigate the formulations capable of encapsulating and trapping the sulfur-based molecules, which are challenging to remove due to their complexity, for example the species present in JP-8 jet fuels.

Ultrasensitive determination of mercury ions using a glassy carbon electrode modified with nanocomposites consisting of conductive polymer and amino-functionalized graphene quantum dots

A one-pot method based on cyclic voltammetric scan was used to fabricate a glassy carbon electrode modified with nanocomposites consisting of poly(thionine) and amino-functionalized graphene quantum dots (afGQDs). Under near-neutral conditions, the dye polymer was effectively oxidized by hydroxyl radicals (·OH) that were derived from the copper-catalyzed Fenton-like reaction, and the cathodic peak current on the modified electrode greatly increased. The reaction of Cu²⁺ with thiourea (TU) and the generation of a complex, CuTU₂⁺, led to the decrease of Cu²⁺/Cu⁺ species, which inhibited the Fenton-like reaction and reduced the electrochemical response change. Due to a displacement reaction, the addition of Hg²⁺ into the H₂O₂-Cu²⁺-TU system resulted in the release of cuprous ions that benefited the Fenton-like reaction. Under the following optimal conditions: 6 mg mL^-1 afGQDs and the 25-cycle potential cycling for the fabrication of the modified electrode, pH 6.5, and the [Formula: see text] ratio of 1.0, the increasing extent of the cathodic peak current exhibited a good linear response to the logarithm of the Hg²⁺ concentration in the range of 1 pM-1 μM with a detection limit of 0.6 pM. Mercury ions in a water sample were determined with good recovery, ranging from 97 to 103%. The investigation on the uptake of Hg²⁺ into human vascular endothelial cells, HUVEC, shows that the cells incubated in the high-concentration glucose medium absorbed more mercury ions than HUVEC incubated in the normal medium. As a result, Hg²⁺ could lead to the greater damage to the former. Graphical abstract.

Novel immobilized ternary photocatalytic polymer film based airlift reactor for efficient degradation of complex phthalocyanine dye wastewater

Reduced graphene oxide (rGO) as well as graphitic carbon nitride (g-C₃N₄) catalysts were synthesized and a physical admixture of rGO and g-C₃N₄ along with TiO₂ in the ratio of 1:1:1 by weight was immobilized in a polystyrene film using the facile solvent casting method. An internal loop airlift reactor with a working volume of 1.2 litres incorporating the prepared polymer-based photocatalytic film was designed and tested for the photocatalytic degradation of remazol turquoise blue dye synthetic wastewater. The reactor parameters affecting the photocatalytic activity such as airflow rate and D_i/D_o (ratio of draft tube diameter to outer tube diameter) were evaluated. The successful operation of the reactor obtained using the ternary immobilized catalyst mixture film gave 92.25% total organic carbon reduction and 94% decolourization within 140 min, compared to 91% decolourization by the slurry form within 40 min. Complete and quicker decolourization of the dye was also demonstrated under the influence of O₃ or H₂O₂. The immobilized catalyst was successfully reused four times. The ternary catalyst admixture employed in this work and the unique design of the photocatalytic reactor helps to increase the degradation rate of toxic textile effluents thus making it suitable for larger scales of treatment.

Lattice substitution and desulfurization kinetic analysis of Zn-based spinel sorbents loading onto porous silicoaluminophosphate zeolites

Green Zn-based spinel sorbents for hot coal gas desulfurization have been developed with the assistance of optimization procedures. The pilot study highlights an outstanding ordered mesoporous support (S_BET = 323 m² g^-1, Da = 4.3 nm) of SAPO-34@as-prepared SBA-15 (SS) for loading active metal oxides. ZnCo₂O₄ spinel loaded onto SS (ZnCo₂/SS) exhibits a prominent desulfurization performance compared to other sorbents whose partial Co is substituted by Mn or Fe in spinel B-site, owing to the slight effect of PO₄^3- in SS. After systematic evaluation on role of sulfidation condition, 50 wt% ZnCo₂/SS sorbent possesses the sulfur storage capacity of 138.08  mg g^-1at550 °C and little loss of active species in 5 desulfurization-regeneration cycles. Results of high resolution transmission electron microscopy (HRTEM), Brunauer-Emmett-Teller (BET), X-ray photoelectron spectroscopy (XPS) etc. demonstrate that 70.42% of initial sulfur capacity of ZnCo₂/SS presented in the 2nd utilization is associated with zinc evaporation, existence of high stable sulfides and partial sintering. The improved deactivation kinetic model suitably describes that the H₂S concentration distribution relates with the spatial position of fixed-bed reactor and desulfurization time.

Supported growth of inorganic-organic nanoflowers on 3D hierarchically porous nanofibrous membrane for enhanced enzymatic water treatment

Organic-inorganic nanoflower is a new type of functional material that can effectively immobilize a wide range of enzymes to form flower-like structures for various enzymatic applications with enhanced catalytic performance and stability. In order to avoid the processing inconvenience and flower structure damage caused by the particular form of these hybrid nanoflowers during material fabrication and catalytic application, different substrates have been used to carry out supported growth of hybrid nanoflowers. However, all previously used substrates have only 2-dimensional feature and only incorporate hybrid nanoflowers on surface with limited nanoflower loading. In this study, three-dimensional (3D) hierarchically porous nanofibrous PVA-co-PE membranes (HPNM) are prepared by a simple template method for effectively immobilizing laccase-Cu₂(PO₄)₃•3H₂O hybrid nanoflowers. Compared with dense nanofibre membrane with only small sized pores (<1 micron), the coexistence of both small and large sized (30-80 microns) pores of HPNM could significantly increase the nanoflower density and allow the penetrated growth of hybrid nanoflowers into the inner structure of the membrane. The hybrid nanoflower containing hierarchically porous nanofibrous membranes (HNF-HPNM) show excellent catalytic performance in degrading different types of textile dyes (reactive blue 2, acid blue 25, acid yellow 76 and indigo carmine), with a degradation efficiency of ˜99.5% for indigo carmine. In addition, the HNF-HPNM could be reused at least 14 times for indigo carmine degradation, with a negligible degradation efficiency drop from 99.48% to 98.52%. These results indicate that hierarchically porous nanofibrous membrane can be a promising type of materials for supported hybrid nanoflower growth for practical applications such as waste water treatment, dye degradation and biosensing.

One-step preparation of reduced graphene oxide aerogel loaded with mesoporous copper ferrite nanocubes: A highly efficient catalyst in microwave-assisted Fenton reaction

Heterogeneous Fenton reaction is an attractive method for degradation of organic pollutants due to its high efficiency and non-selectivity and it also causes no secondary pollution. However, low degradation rate and poor recyclability of the catalysts limit its applications for water purification. To overcome this, herein, copper ferrite/reduced graphene oxide (CF/rGO) aerogel was prepared by a one-step hydrothermal method, as a highly efficient catalyst for the microwave-assisted Fenton reaction (MAFR). Under optimal conditions (500 W of microwave power, 600 μL of H₂O₂, 15 mg of catalyst, and 30 mg/L of RhB), the degradation efficiency of CF/rGO aerogel at 1.0 min (95.7%) was higher than that of reference samples at 3.0 min. Thermodynamical study showed the activation energy, enthalpy change, entropy change, and Gibbs free energy change were 0.73 kJ/mol, -49.5 kJ/mol, -0.135 kJ/mol·K, and -6.8 kJ/mol, respectively, indicating that MAFR was an endothermic and non-spontaneous process.Radical trapping experiments showed that OH, O₂^-, and h⁺ played a combined role in RhB degradation. Besides high catalytic activity, CF/rGO aerogel also displayed good reusability, showing removal efficiency of 87.4% after 5 cycles. The high efficiency, good reusability, and simple process make CF/rGO aerogel a promising catalyst for wastewater treatment.

One-step reductive synthesis of Ti3+ self-doped elongated anatase TiO2 nanowires combined with reduced graphene oxide for adsorbing and degrading waste engine oil

A sustainable photocatalyst of Ti³⁺ self-doped elongated anatase nanowires combined with reduced graphene oxide (TiO₂ NWs@rGO) was prepared via a facile one-step reductive synthesis process using NaBH₄ as reductant for the first time. The obtained optimal TiO₂ NWs@rGO composite has a large surface area,182 m²  g^-1, which demonstrates strong adsorption capacity due to the multilayered structure built by highly crystallized nanowires of TiO₂ and ultrathin rGO layers. When the photocatalyst was applied in removing waste engine oil (100 mL, 50 mg L^-1), it exhibited outstanding performance with up to COD 98.6% removal extent (from 145 initial to 2 mg L^-1 final COD) after 5 h, which is 34.1% higher than that of TiO₂ NWs (64.5% COD removal extent). Gas chromatography-mass spectrometry analyses of residual waste engine oil after photocatalysis shows significant reductions of C₆-C₁₉ chemicals as well as total disappear of C₁₅,C₁₆, C₁₇, C₁₈ chemicals. The outstanding photocatalytic activity of TiO₂ NWs@rGO benefits from sensitive response to visible light, improved surface reactivity and high electron flux enabled by rGO and Ti³⁺ in TiO₂. In addition, this composite catalyst can be self-cleaned, and recycled for reuse, which suggests promising potential for waste engine oil treatment.

Optimization of Aqueous NH4+/NH3 Photodegradation by ZnO/Zeolite Y Composites Using Response Surface Modeling

In this study, ZnO/Zeolite Y composites were synthesized by the solid state dispersion method and employed in order to investigate their photocatalytic performance in NH4+/NH3 removal from an aqueous solution. FTIR spectroscopy, UV-vis diffuse reflectance spectroscopy, SEM and EDX analyses were applied to characterize these composites. The three-factor, three-level Box-Behnken experimental design (BBD), as one of the response surface methodology (RSM), was used to achieve maximum removal of aqueous NH4+/NH3 under optimum conditions by ZnO/Zeolite Y composites. The effects of parameters such as ZnO loading (10–50 wt %), initial pollutant concentration (25–315 mg/L) and solution pH (3–11) as well as their interactions were determined on removal of NH4+/NH3 by the mentioned method. It was found that pH of the solution with the percentage contribution of 86.79 %, was the most important parameter among the others. A second-order polynomial equation was well fitted on the experimental data with the determination coefficient value of 0.9932 and the adjusted determination coefficient value of 0.9864. It could not describe only 0.68 % of observed changes in the response. The predicted removal percentage of NH4+/NH3 at the optimal conditions (pH = 11, NH4+/NH3 initial concentration (207.21 mg/L) and ZnO loading (45.02 wt %)) was achieved 62.26 %, which was in agreement with its experimental value (65 %) obtained in similar conditions.

Phase control synthesis of α, β and α/β Bi2O3 hetero-junction with enhanced and synergistic photocatalytic activity on degradation of toxic dye, Rhodamine-B under natural sunlight

Nano particles of a few α/β Bi₂O₃ hetero-junctions of various compositions synthesized by one- pot hydrothermal method, exhibit exceptional and synergistic photo-catalytic activity for the degradation of Rhodamine-B in aqueous solution under natural sunlight. Pure α and pure β Bi₂O₃ are also synthesized by control post heating of synthesized hetero-junction. The nano-materials were characterized by diffraction (XRD), microscopic and spectroscopic techniques. The XRD reveals α-β phase hetero-junctions of Bi₂O₃ are made of α-Bi₂O₃ and β-Bi₂O₃ with average dimensions within 13-113 and 5-71 nm respectively and having band gap range of 2.4- 2.9 eV. The spectrophotometrically determined % degradation of the dye and associated rate constant on the best hetero-junction are increased by 4.5(/2.1) and 3.3(/1.2) times than these on pure α (/β). The effects of operational parameters and trapping agents have been analyzed. The maximum removal of the dye was achieved up to 99.6% in 3 h using 0.5 g/L photo-catalyst at pH 3. The reusability test shows that the photo-catalytic activity is retained excellently due to change in chemical nature of the catalyst from α -Bi₂O₃ to β-Bi₂O_3, Bi₂O₂CO₃ and BiOCl. A suitable mechanism is proposed.

Synergistic effect of p-n heterojunction, supporting and zeolite nanoparticles in enhanced photocatalytic activity of NiO and SnO2

Increased photocatalytic activity of NiO and SnO₂ was achieved by coupling and supporting of them onto clinoptilolite nanoparticles (NC) via calcination of Ni(II)-Sn(IV) - exchanged NC in photocatalytic degradation of metronidazole (MZ) aqueous solution. XRD, XRF, FTIR, SEM, X-ray mapping, DRS, TEM, BET Cyclic voltammetry and electrochemical impedance spectroscopy techniques (EIS) were used for characterization of samples. Red shift occurred in bang gap energies of the coupled semiconductors with respect to monocomponent one. This p-n hetero-junction forms a depletion layer in the semiconductors interface with negative and positive charges, causing considerable enhancement in the photocatalytic activity. The calcined catalyst at 600°C for 4h showed the best photocatalytic activity and charge transfer efficiency (in EIS results). The mole ratio of SnO₂/NiO affects the degradation activity of the catalysts and the best activity were was obtained for the NiO_1.1-SnO_2(6.7)/NC (NS₅-NC) catalyst at pH 3, 1.2gL^-1 of the catalyst and 2mgL^-1 of MZ. SnO₂ played electron sink role and the photogenerated electrons migrate from more negative C_b-NiO (E=-3.0V) to C_b-SnO₂ (E=-0.3V vs SHE). Initial pH of MZ solution was changed from 6.20 to 4.73 during 180min that confirms formation of Oxalic acid and Maleic acid.