Amino-functionalized hierarchical porous SiO2-AlOOH composite nanosheets with enhanced adsorption performance

Reconstructing Kaolinite Compounds for Remarkably Enhanced Adsorption of Congo Red

Organic dyes are widely used in many important areas, but they also bring many issues for water pollution. To address the above issues, a reconstructed kaolinite hybrid compound (γ-AlOOH@A-Kaol) was obtained from raw kaolinite (Kaol) in this work. The product was then characterized by X-ray diffraction (XRD), Fourier-transform infrared (ATR-FTIR), Brunauer-Emmett-Teller (BET), and scanning electron microscopy (SEM), and the absorption properties of γ-AlOOH@A-Kaol for congo red were further studied. The results demonstrated that flower-like γ-AlOOH with nanolamellae were uniformly loaded on the surface of acid-treated Kaol with a porous structure (A-Kaol). In addition, the surface area (36.5 m2/g), pore volume (0.146 cm3/g), and pore size (13.0 nm) of γ-AlOOH@A-Kaol were different from those of A-Kaol (127.4 m2/g, 0.127 cm3/g, and 4.28 nm, respectively) and γ-AlOOH (34.1 m2/g, 0.315 cm3/g, and 21.5 nm, respectively). The unique structure could significantly enhance the sorption capacity for congo red, which could exceed 1000 mg/g. The reasons may be ascribed to the abundant groups of -OH, large specific surface area, and porous structure of γ-AlOOH@A-Kaol. This work provides an efficient route for comprehensive utilization and production of Kaol-based compound materials that could be used in the field of environmental conservation.

Facet-dependent adsorption of heavy metal ions on Janus clay nanosheets

Understanding the facet-dependent adsorption behavior and mechanism of heavy metal ions (HMs) on two-dimensional (2D) Janus nanoclays has important implications for the environment and ecosystem but still remains elusive. Herein, ultrathin Janus serpentene (2D serpentine) nanosheets were fabricated via a facile, nontoxic, and residue-free exfoliation strategy. Fabricated serpentene nanosheets exhibited promising Cd(II) and Pb(II) adsorption capacities due to their high surface areas and abundant active sites, approximately four times higher than those of bulk serpentine powders. Interestingly, Cd(II) and Pb(II) adsorption on serpentene nanosheets exhibited a facet-dependent feature, with the adsorption amount on the Mg-OH plane considerably higher than that on the Si-O plane. This facet-dependent adsorption behavior was mainly attributed to the difference in the interaction mechanisms of HMs with the Mg-OH (monodentate inner-sphere complexation) and Si-O (outer-sphere complexation) planes, which was further confirmed via density functional theory calculations. The Cd(II) adsorption on serpentene nanosheets was limited by strong kinetic restrictions (e.g., stronger electrostatic repulsion and higher dehydration energy barrier than that for Pb(II) adsorption). This study provides insights into the facet-dependent adsorption mechanisms of HMs on Janus serpentene nanosheets, which can be extended to other nanoclays used in wastewater treatment and many environmental processes.

ZIF-67 grafted-boehmite-PVA composite membranes with enhanced removal efficiency towards Cr(VI) from aqueous solutions

In this work, we developed a thin membrane of boehmite-polyvinyl alcohol composite (BOPOM) (diameter ∼ 5 cm) grafted ZIF-67 combing sol-gel and in-situ growth methods. The fabricated materials were characterized using FT-IR, SEM, XRD, TGA, XPS, and N2 sorption techniques. Results indicate that ZIF-67 nanocrystals were well-grafted into the AlOOH-PVA matrix with reduced crystallite size. Furthermore, the decorated ZIF-67 offered additional porous structures and adsorption sites onto the membrane, enhancing their removal efficiency towards Cr6+ compared to the undecorated and pristine ZIF-67. At pH ∼5.5, the harvested ZIF-67/BOPOM exhibited the highest Cr6+ uptake capacity of ∼56.4 mg g-1. Kinetic studies showed that the chromium adsorption on the prepared materials obeyed the pseudo-second-order model, and the kinetic parameters followed the order ZIFF-67/BOPOM (0.020 mg g-1 min-1) > BOPOM (0.011 mg g-1 min-1) > ZIF-67 (0.006 mg g-1 min-1). Notably, the adsorption mechanism study revealed that adsorbed Cr6+ was reduced to Cr3+, and the reduction yield was boosted owing to grafting ZIF-67 into the BOPOM. In addition, the fabricated ZIF-67/BOPOM can simultaneously remove Cr6+ and methyl orange dye (MO) in the solution due to their synergetic effects on each other. Furthermore, the hybrid membrane ZIF-67/BOPOM showed a chromium removal efficiency of ∼78.2% after four successive adsorption-desorption cycles. This study indicates that grafting nanocrystals ZIF-67 onto the super-platform boehmite-PVA is a promising strategy to harvest an adsorbent with a high adsorption ability, cost-effectiveness, and reduced secondary pollution risks.

Visible Light Locking in Mineral-Based Composite Phase Change Materials Enabling High Photothermal Conversion and Storage

Fully stimulating the capacity of light-driven phase change materials (PCMs) for efficient capture, conversion, and storage solar energy requires an ingenious combination of PCMs, supporting structural materials, and photothermal materials, therefore motivating the synergistic effects between the components. Herein, this work thoroughly explores the interaction forces between PCMs and supporting structural materials and the synergy between PCMs and photothermal materials in photothermal conversion. Rejoicingly, when capitalizing on the prepared directional channel structure of hierarchically porous composite aerogel (PEPG) as a supporting structural material, a superior paraffin wax (PW) encapsulation rate of 85.11% is achieved, and the prepared PEPG2-PW has a high phase change enthalpy of 182.9 J/g. The van der Waals force and Lewis acid-base action between PEPG and PW molecules reveal the excellent stabilities of PEPG-PW. More importantly, the PEPG2-PW has an ultrahigh photothermal conversion efficiency of 95.2% under 1 sun irradiation and durability. Most importantly, the COMSOL Multiphysics software calculations demonstrate that transparent PW can anchor sunlight on the surface of graphite nanoplates, converting it into heat by enhancing the loss of graphite backbone lattice vibrations, and the accumulated heat is then stored in molten PW. This work provides some design principles for high-efficiency solar-thermal conversion materials.

Methylene Blue Dye Adsorption on Iron Oxide-Hydrochar Composite Synthesized via a Facile Microwave-Assisted Hydrothermal Carbonization of Pomegranate Peels' Waste

The toxicity of dyes has a long-lasting negative impact on aquatic life. Adsorption is an inexpensive, simple, and straightforward technique for eliminating pollutants. One of the challenges facing adsorption is that it is hard to collect the adsorbents after the adsorption. Adding a magnetic property to the adsorbents makes it easier to collect the adsorbents. The current work reports the synthesis of an iron oxide-hydrochar composite (FHC) and an iron oxide-activated hydrochar composite (FAC) through the microwave-assisted hydrothermal carbonization (MHC) technique, which is known as a timesaving and energy-efficient method. The synthesized composites were characterized using various techniques, such as FT-IR, XRD, SEM, TEM, and N2 isotherm. The prepared composites were applied in the adsorption of cationic methylene blue dye (MB). The composites were formed of crystalline iron oxide and amorphous hydrochar, with a porous structure for the hydrochar and a rod-like structure for the iron oxide. The pH of the point of zero charge (pHpzc) of the iron oxide-hydrochar composite and the iron oxide-activated hydrochar composite were 5.3 and 5.6, respectively. Approximately 556 mg and 50 mg of MB dye was adsorbed on the surface of 1 g of the FHC and FAC, respectively, according to the maximum adsorption capacity calculated using the Langmuir model.

Facile Preparation and Characterization of Silica Nanoparticles from South Africa Fly Ash Using a Sol–Gel Hydrothermal Method

Silica nanoparticles (SNPs) consist of several applications which include lightweight aggregates, energy storage, and drug delivery. Nevertheless, the silica reagents used in SNP synthesis are both costly and hazardous. As a result, it is critical to look for other sources of silica. For this research, a simple sol–gel hydrothermal approach is used to make SNPs from South African fly ash (SAFA). SAFA is classified as fly ash class F according to X-ray fluorescence (XRF) analysis. The wide-angle X-ray diffraction (XRD) pattern reveals the structural composition of SAFA and the amorphous phase of extracted SNPs, while Fourier transform infrared (FTIR) examination reveals the presence of silanol and siloxane groups. Basic SNPs were generally spherical with diameters of about 60 nm, according to scanning electron microscopy (SEM) and transition electron microscope (TEM) studies. The presence of SiO2 is confirmed by energy-dispersive X-ray spectroscopy (EDX) spectrum analysis. Particle size assessment indicates particle sizes ranging from 48 nm to 87 nm in diameter, with a mean diameter of 67 nm. The application of SNPs in wastewater treatment demonstrated that they can be used to remove Cd2+ from an aqueous solution. This research offers new ideas for using South African fly ash in SNP manufacturing.

Natural kaolinite-based hierarchical porous microspheres as effective and highly recyclable adsorbent for removal of cationic dyes

The development of efficient, recyclable, and environment-friendly adsorbent for wastewater remediation is considered a challenge. In this study, a hierarchical porous kaolinite microsphere (HPKS) with three-dimensional (3D) structure was fabricated based on natural-layered kaolinite mineral via an environmentally friendly direct hydrothermal strategy. Characterization results revealed that HPKS microsphere with 3D hierarchical porous structure was constructed with numerous nanospheres which are assembled by ultrafine aluminosilicate flakes. HPKS exhibited negative charge feature ranging from strong acid to high alkaline solution. The influence of contact time, solution pH, initial dye concentration, adsorbent dosage, and foreign ions on methylene blue (MB) adsorption capability was systematically investigated. The synthesized HPKS with higher specific surface area (250.6 m²/g) shows an outstanding adsorption capacity towards MB (411.8 mg/g) and excellent selectivity for cationic MB dyes over anionic methyl orange and competitive metal ions. The adsorption kinetic experiment results fit very well with the pseudo-second-order model and reflect the fast adsorption rate of MB on HPKS. The sorption isotherm study reveals the chemisorption of electrostatic attraction between the cationic MB molecules and the negative charged surfaces of HPKS. More importantly, the MB removal efficiency is more than 99% in a broad range of solution pH value. The adsorption capacities of HPKS can be easily recovered by calcination at 600 °C to remove the adsorbed dyes and without obvious diminishment even after six successive cycles. Therefore, the HPKS is a cost-effective and environmentally friendly adsorbent which has is promising to use in practical applications.

Deep eutectic solvent-assisted synthesis of porous Ni2CO3(OH)2/SiO2 nanosheets for ultra-efficient removal of anionic dyes from water

Wastewater treatment is a severe environment issue, especially the discharge of excessive synthetic dyestuffs in the aquatic environment. In this study, a facile binary deep eutectic solvothermal process plus silica surface modification was successfully applied for preparation of porous nanosheet Ni₂CO₃(OH)₂/SiO₂ composites. The composites show powerful anionic dyes removal ability due to the high specific surface areas, hydrogen bond connection, coordination effect and strong electrostatic interactions with anionic dyes. A maximum adsorption capacity of 2637 mg g^-1 at neutral pH (ca.7) and 303 K was achieved for Ni₂CO₃(OH)₂/SiO₂ composite to adsorb Congo red, a representative anionic dye. Moreover, the composite has an excellent specificity for anionic dyes and could maintain above 95% removal efficiency after 5 cycles. Therefore, the as-prepared nanocomposites could be qualified as candidates for industrial environmental remedy. Furthermore, the proposed material preparation strategy could be extended to fabricate various advanced energy and environmental materials.

Review on nickel-based adsorption materials for Congo red

Excessive synthetic dyestuffs in the aquatic environment pose various ecological and health issues that are detrimental to sustainable development. Adsorption is considered a feasible technique of eliminating dye pollutants from the water environment because of its advantages of high efficiency, low cost, easy operation, and absence of secondary pollution. Among the many dyes, Congo red (CR) is a widely used azo dye. Nickel-based materials, including nickel hydroxide, nickel oxide, nickel-containing layered double hydroxides, nickel-based spinel and metal-organic frameworks, metallic nickel, nickel-based sulfide, and nickel composites, have been extensively studied for CR adsorption due to their morphological diversity, large specific surface area, and strong affinity toward CR. However, fabricating nickel-based adsorbents with high efficiency and stability and excellent recyclability for practical application remains a challenge. This review outlines the research progress of nickel-based materials in CR adsorption. The interaction between CR molecules and nickel-based adsorbents is systematically presented, and the possible adsorption mechanisms are summarized. Finally, the challenges and future development directions of the practical application of nickel-based adsorbent materials are proposed.

Batch and fixed-bed adsorption behavior of porous boehmite with high percentage of exposed (020) facets and surface area towards Congo red

Boehmite adsorbents with high percentage of exposed (020) facets and large specific surface area were prepared by a separate nucleation and aging steps route with excellent performance towards Congo red in batch and fixed-bed adsorption columns.

Preparation of a Three-Dimensional Porous Graphene Oxide-Kaolinite-Poly(vinyl alcohol) Composite for Efficient Adsorption and Removal of Ciprofloxacin

Because of the widespread presence of antibiotics in water, soil, and other environments, they pose great potential risks to the environment, threatening human and animal health. In this study, graphene oxide-kaolinite homogeneous dispersion was prepared by simple liquid phase exfoliation. The three-dimensional (3D) porous graphene oxide-kaolinite-poly(vinyl alcohol) composites were prepared by the cross-linking of poly(vinyl alcohol) and the formation of ice crystals during the freezing-drying process. Three influencing factors [adsorbent dosage, ciprofloxacin (CIP) initial concentration, and time] of CIP adsorption and removal were systematically analyzed by the response surface method. The order of significance for response values (CIP removal rate) was adsorbent dosage > CIP initial concentration > time. The 3D porous material showed good adsorption capacity of CIP, the theoretical maximum adsorption capacity was 408.16 mg/g, and it had good recyclability. By Fourier transform infrared (FTIR) and X-ray photoelectron spectroscopy analysis, it was found the composite adsorbs CIP by hydrogen bonding and π-π interaction. In conclusion, the graphene oxide-kaolinite-poly(vinyl alcohol) porous composite is a good candidate for efficient antibiotic wastewater treatment.

Self-standing zeolite foam monoliths with hierarchical micro-meso-macroporous structures

The zeolite monoliths were synthesized by a facile polymer scaffold template assisted hydrothermal method. The selected foam-shaped template of a polyurethane (PU) foam monolith, was used to prepare the self-standing zeolite foam (ZF) monolithic materials. The obtained ZF products can preserve the same size, shape and macroporous network structure of the original PU foam scaffold template, although the zeolite nano-crystallites had been fully substituted for the PU template to form the new skeleton struts and walls. The as-synthesized ZF products demonstrated abundant hierarchical porosity (involving triple micro-, meso- and macropores). Meanwhile, compared with the conventional zeolite powders, the self-standing ZF monolithic materials exhibited greater total pore volume and nearly three times higher mesopore volume, suggesting wider applications as catalysts, catalyst supports and adsorbents in industry.

A Convenient and Versatile Strategy for the Functionalization of Silica Foams Using High Internal Phase Emulsion Templates as Microreactors

Functional porous materials show extensive applications in the environment, biology, aerospace, and so on. In this work, the generation of silica foams and functionalization of pore surface were simultaneously realized through an interfacial sol-gel reaction within high internal phase emulsion (HIPE) microreactors, where a hyperbranched polyethoxysiloxane (PEOS) was used as the sole stabilizer for the HIPEs. With various functional substances containing amino, epoxy, and carboxyl groups initially dissolved in the aqueous phase of HIPEs, these functional groups could be grafted onto the pore surface in the process of forming silica foams. Amino-functionalized silica foam showed fast adsorption of sunset yellow, and the adsorption capacity could reach as high as 1213.13 mg/g. Sodium polyacrylate-modified silica foam exhibited good adsorption capacity of cationic dyes and metal ions, e.g., 280.11 mg/g to methylene and 226.24 mg/g to Cu(II). Epoxy-functionalized silica foam particles were confirmed with a pronounced activity at the oil/water interface due to their Janus-like surface, which could be used as Pickering stabilizer. This HIPE-based synthesis strategy for silica foams shows promising future in adsorption, emulsion stabilization, and compatibilization.

Surfactant-free preparation of mesoporous solid/hollow boehmite and bayerite microspheres via double hydrolysis of NaAlO2 and formamide from room temperature to 180 °C

The transformation from solid boehmite microspheres to hollow bayerite microspheres at room temperature (25 °C) was successfully realized via the double hydrolysis of NaAlO₂ and formamide (FA) solution. Effects of reaction time, temperature and FA dos on the transformation process were studied in detail. The results show that hollow boehmite microspheres were obtained via increasing the temperature above 120 °C and the FA dos above 12 mL; amorphous alumina hydrate, solid boehmite and hollow bayerite microspheres were also obtained at 25 °C for 1 h, 2 h and 24 h reactions, respectively; solid bayerite microspheres were obtained by decreasing the FA dos below 4 mL at 25 °C. Because of the slow change of pH from 12.9 to 8.7, simultaneous dissolution and regeneration for different aluminum hydroxide were the key factors for forming hollow boehmite/bayerite microspheres. The Al yield for boehmite microspheres reached 41.4% at 25 °C for a 2 h reaction; when increasing the temperature to 180 °C, the Al yield for hollow boehmite microspheres with higher crystallinity increased to 82.7%. Moreover, the solid/hollow boehmite microspheres with high surface areas showed outstanding adsorption capacities of 751.9 mg/g and 694.4 mg/g, respectively, for Congo red. This significant transformation of structure and morphology provides an effective strategy for preparing mono-phase hydrated alumina with excellent adsorption performance.

Emerging WS2/montmorillonite composite nanosheets as an efficient hydrophilic photocatalyst for aqueous phase reactions

Tungsten disulfide (WS₂) as one of transition metal dichalcogenides exhibits excellent catalytic activity. However, its catalytic performances in aqueous phase reactions are limited by its hydrophobicity. Here, the natural hydrophilic two-dimensional clay was used to enhance the dispersibility of WS₂ in aqueous phase. WS₂/montmorillonite (WS₂/MMT) composite nanosheets were prepared via hydrothermal synthesis of WS₂ on the surface of montmorillonite from WCl₆ and CH₃CSNH₂. The microstructure and morphology show that WS₂ nanosheets are assembled parallelly on the montmorillonite with the interface interaction. Through the support of montmorillonite, WS₂/MMT possesses higher photocatalytic ability for aqueous phase reactions than WS₂, which could be due to the synergistic effect of higher adsorption property, higher hydrophilicity, dispersibility and more catalytic reaction site. The strategy could provide new ideas for obtaining novel hydrophilic photocatalyst with excellent performance.

Synthesis of amino-functionalized magnetic aerobic granular sludge-biochar for Pb(II) removal: Adsorption performance and mechanism studies

In the present study, a novel amino-functionalized magnetic aerobic granular sludge-biochar (NH₂-M-AGS) was successfully fabricated through magnetization and functional modification and applied for Pb(II) sorption. The composite was characterized by using scanning electron microscopy (SEM), energy dispersive spectrum (EDS), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Zeta potential analysis, vibrating sample magnetometer (VSM) and X-ray photoelectron spectroscopy (XPS). The effects of adsorbent dosage, pH value, contact time and initial metal concentration on the adsorption of Pb(II) were investigated by using batch equilibrium experiments. It was concluded that the pseudo-second-order model was better to describe adsorption kinetic of Pb(II) onto NH₂-M-AGS. The Langmuir model was more accorded with the experimental data, and the maximum adsorption capacity of Pb(II) was 127.0 mg/g. A possible adsorption mechanism could be mainly caused by surface complexation, electrostatic attraction and precipitation. In five adsorption-desorption cycles, the desorption efficiency of Pb(II) exhibited a slight decline and still reached at 88.14%. Furthermore, the good reproducibility indicated that NH₂-M-AGS could be used a desirable, economic and recyclable adsorbent in practical metal-contaminated wastewater treatment.

Self-templated microwave-assisted hydrothermal synthesis of two-dimensional holey hydroxyapatite nanosheets for efficient heavy metal removal

Heavy metals have caused serious environmental problems and threat to human health. Ultrathin and holey two-dimensional (2D) nanosheets have recently drawn significant attention as superb adsorbent material to remove heavy metal ions due to their unique physicochemical properties. Herein, we report a self-template-directed ultrafast reaction route to synthesis porous hydroxyapatite (Ca₁₀(PO₄)₆(OH)₂) nanosheets via a microwave-assisted hydrothermal method using poly(allylamine hydrochloride) as an additive. The resulting hydroxyapatite nanosheets showed a high specific surface area (92.9 m² g^-1) and excellent adsorption performance for various heavy metal ions including Pb(II), Cu(II), and Cd(II), with maximum adsorption capacities of 210.5, 31.6, and 24.9 mg g^-1, respectively. The adsorption kinetics fitted well with the pseudo-second-order equation and the equilibrium data showed a high correlation coefficient with the Langmuir model. Based on the experimental results and analysis, we can conclude that the sorption of heavy metal ions with the hydroxyapatite nanosheets mainly attributes to surface complexation and cation exchange. The present synthetic strategy allows the fast and massive production of porous hydroxyapatite ultrathin nanosheets and may also potentially be applicable to the fabrication of other metal phosphates with assembled or hierarchical porous structures towards various applications such as water purification.

Rapid adsorption and reductive degradation of Naphthol Green B from aqueous solution by Polypyrrole/Attapulgite composites supported nanoscale zero-valent iron

Polypyrrole/Attapulgite-supported nanoscale zero-valent iron (PPy/APT-nZVI) composites employed to extract Naphthol Green B (NGB) from aqueous solution, were successfully fabricated by chemical oxidative polymerization and liquid-phase reduction method. Comparison experiment of different materials showed that 99.59% of NGB was removed using PPy/APT-nZVI (1:0.5) after 25 min, much higher than APT, PPy, PPy/APT and nZVI. The morphology and structure of PPy/APT-nZVI (1:0.5) composites were characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), which confirmed the high disperse and activity of nZVI after supported by PPy/APT. Furthermore, dynamic studies revealed that removal process was highly consistent with not only the pseudo-second-order model for adsorption but also pseudo-first-order model for degradation process, which proved the removal was controlled by chemical surface-limiting step. A possible removal mechanism, containing prompt adsorption of NGB onto the PPy/APT-nZVI (1:0.5) surface and being degraded by nZVI, was put forward. Additionally, the stability study verified the activity of nZVI can retain longer time than that of single nZVI due to such powerfully protective layers of PPy/APT.

Simple Synthesis and Characterization of Hexagonal and Ordered Al–MCM–41 from Natural Perlite

Silica reagents are expensive and toxic for use in the synthesis of mesoporous silica materials. It is imperative to take an interest in green silicon sources. In this paper, we report the synthesis of hexagonal and ordered aluminum-containing mesoporous silica materials (Al–MCM–41) from natural perlite mineral without addition of silica or aluminum reagents. A pretreatment process involving acid leaching, alkali leaching, and strongly acidic cation exchange resins treatment was critical to obtain silicon and aluminum sources from natural perlite mineral. The Al–MCM–41 material was synthesized via a hydrothermal reaction with hexadecyl trimethyl ammonium bromide (CTAB) as the template and subsequent calcination. The resulting mesophase had a hexagonal and ordered mesoporous structure, confirmed by small-angle X-ray diffraction (SAXRD) and transmission electron microscopy (TEM). Al–MCM–41 material had a high Brunauer–Emmet–Teller (BET) surface area of 1024 m2/g, pore volume of 0.72 cm3/g and an average pore diameter of 2.8 nm with a pore size distribution centered at 2.5 nm. The thermal behavior of the as-synthesized samples during calcination was investigated by thermogravimetry (TG) and differential thermogravimetry (DTG) analysis. The Al–MCM–41 material showed a negative surface charge in aqueous solution with the pH value ranging from 2 to 13. The variations of chemical structures from natural perlite to Al–MCM–41 were traced by wide-angle X-ray diffraction (WAXRD) and Fourier-transform infrared spectroscopy (FTIR). A proposed mechanism for the synthesis of hexagonal and ordered mesoporous silica materials from natural perlite is discussed.

Effect of Structure and Chemical Activation on the Adsorption Properties of Green Clay Minerals for the Removal of Cationic Dye

In this study, natural clay minerals with green appearance were treated with sulfuric acid. Mass percentage of acid (wt%), temperature (T), contact time (t) and liquid-to-solid mass ratio (R) are used as the prevailing factors that determine the extent of acid-activation. The values of these factors range from 15–50%, 60–90 °C, 1.5–6 h and 4–7, respectively. The study has focused on the structural changes as well as textural characteristics of the clay. Three activated clay samples were prepared under different treatment conditions. The samples were characterized using X-ray powder diffraction (XRD), fourier transform infrared (FTIR), scanning electron microscope (SEM), chemical analysis and N2 adsorption techniques. Characterization of the treated clay minerals exhibited significant structural changes to a greater extent of acid-activation, from being partially crystalline to being amorphous silica. The surface area and total pore volume of clay increased proportionally with the level of acid treatment. The average pore diameter behaved differently. During the strong acid treatment, a large increase in pore volume and the enlargement of the pore size distribution were observed. This suggests that considerable structural changes and partial destruction may have occurred in this condition. The removal of methylene blue, used as cationic dye, from aqueous solution by the batch adsorption technique on three prepared acid-activated clay samples was studied. The Langmuir model was found to agree well with the experimental data.