Enhanced catalytic ozonation by highly dispersed CeO2 on carbon nanotubes for mineralization of organic pollutants

Comparative study on CeO2 catalysts with different morphologies and exposed facets for catalytic ozonation: performance, key factor and mechanism insight

Morphology and facet effects of metal oxides in heterogeneous catalytic ozonation (HCO) are attracting increasing interests. In this paper, the different HCO performances for degradation and mineralization of phenol of seven ceria (CeO2) catalysts, including four with different morphologies (nanorod, nanocube, nanooctahedron and nanopolyhedron) and three with the same nanorod morphology but different exposed facets, are comparatively studied. CeO2 nanorods with (110) and (100) facets exposed show the best performance, much better than that of single ozonation, while CeO2 nanocubes and nanooctahedra show performances close to single ozonation. The underlying reason for their different HCO performances is revealed using various experimental and density functional theory (DFT) calculation results and the possible catalytic reaction mechanism is proposed. The oxygen vacancy (OV) is found to be pivotal for the HCO performance of the different CeO2 catalysts regardless of their morphology or exposed facet. A linear correlation is discerned between the rate of catalytic decomposition of dissolved ozone (O3) and the density of Frenkel-type OV. DFT calculations and in-situ spectroscopic studies ascertain that the existence of OV can boost O3 activation on both the hydroxyl (OH) and Ce sites of CeO2. Conversely, various facets without OV exhibit similar O3 adsorption energies. The OH group plays an important role in activating O3 to produce hydroxyl radical (∙OH) for improved mineralization. This work may offer valuable insights for designing Facet- and OV-regulated catalysts in HCO for the abatement of refractory organic pollutants.

Effect of impregnation strategy on structural characteristics of Ce-Mn/Al2O3 and its catalytic ozonation of benzoic acid

Ce-Mn binary oxides supported on Al2O3 (Ce-Mn/Al2O3), with enhanced activity and stability for catalytic ozonation of benzoic acid, were synthesized using a facile impregnation method. The competitive synergetic effects between cerium and manganese significantly influenced the structural characteristics and catalytic performance of the catalysts depending on the impregnation sequence. Catalysts prepared via the one-step impregnation process exhibited a higher concentration of homogeneous Ce3+ species on the catalyst surface. This led to an increase in surface oxygen vacancies, thereby enhancing catalytic activity. In contrast, the two-step impregnation process resulted in fewer oxygen vacancies due to reduced competitive effects between cerium and manganese. Overall, the optimized Ce-Mn/Al2O3 catalysts demonstrated improved catalytic performance in ozonation reactions, highlighting the importance of impregnation method and calcination conditions in tailoring catalyst properties for enhanced activity and stability. Oxygen vacancies play a crucial role as active sites for ozone adsorption and dissociation into *O2 and *O, facilitated by the reduction of Mn4+ to Mn3+ and the oxidation of Ce3+ to Ce4+. This process forms an electron closed loop that maintains electron balance. The synergistic interactions between cerium and manganese enable rapid electron transfer between Ce4+ and Mn3+, facilitating the regeneration of Ce3+ and Mn4+. Due to the increase of the dual redox conjugate pairs and the surface reactive oxygen species, the catalytic ozonation activity and stability of Ce-Mn/Al2O3 was enhanced.

MgO-loaded tubular ceramic membrane with spatial nanoconfinement for enhanced catalytic ozonation in refractory wastewater treatment

Heterogeneous catalytic ozonation (HCO) enables the destruction of organic pollutants in wastewater via oxidation by powerful hydroxyl radicals (·OH). However, the availability of short-lived ·OH in aqueous bulk is low in practical treatment scenarios due to mass transfer limitations and quenching of water constituents. Herein, we overcome these challenges by loading MgO catalysts inside the pores of a tubular ceramic membrane (denoted as CCM) to confine ·OH within the nanopores and achieve efficient pollutant removal. When the pore size of the membrane was reduced from 1000 to 50 nm, the removal of ibuprofen (IBU) by CCM was increased from 49.6 % to 90.2 % due to the enhancement of ·OH enrichment in the nanospace. In addition, the CCM exhibited high catalytic activity in the presence of co-existing ions and over a wide pH range, as well as good self-cleaning ability in treating secondary wastewater. The experimental results revealed that ·OH were the dominant reactive oxygen species (ROS) in pollutant degradation, while surface hydroxyl groups were active sites for the generation of ·OH via ozone decomposition. This work provides a promising strategy to enhance the utilization of ·OH in HCO for the efficient degradation of organic pollutants in wastewater under spatial confinement.

In-situ growth of Mn-Ni3S2 on nickel foam for catalytic ozonation of p-nitrophenol

In this study, a new catalyst for catalytic ozonation was obtained by in-situ growth of Mn-Ni3S2 nanosheets on the surface of nickel foam (NF). The full degradation of p-nitrophenol (PNP) was accomplished under optimal conditions in 40 min. The effects of material dosage, ozone dosage, pH and the presence of inorganic anions on the degradation efficiency of PNP were investigated. ESR analysis showed that singlet oxygen (1O2) and superoxide radical (O2•-) are the main contributors of PNP degradation. This study offers a new combination of supported catalysts with high efficiency and easy recovery, which provides a new idea for wastewater treatment.

Oxygen-doped carbon nanotubes with dual active cites to enhance •OH formation through three electron oxygen reduction

The electro-Fenton (EF) process generates H2O2 through the 2e- oxygen reduction reaction (ORR), which is subsequently activated to •OH by iron-based catalysts. To alleviate the potential risk of external Fe-based catalysts, along with metal dissolution in acidic or neutral environments, in this study we employed oxygen-doped carbon nanotubes (OCNT) as a bifunctional, metal-free cathode to establish a metal-free EF process for organic pollutant degradation. The results demonstrate that the metal-free electrode has excellent H2O2 accumulation (12 mg L-1 cm-1) and degrades sulfathiazole (STZ) with 97.05 % efficiency in 180 min with an explanation kinetic of 0.0189 min-1. For the first time, this enhancement came from the dual active site centers in OCNT: Ⅰ) -COOH and defects active sites were responsible for H2O2 production, Ⅱ) then -CO triggered H2O2 into •OH, avoiding the introduction of metal-based catalysts. These findings suggest that the EF system with in situ oxygen-doped cathodes have great potential for treating antibiotic wastewater.

Efficient catalytic activity of NiO and CeO2 films in benzoic acid removal using ozone

This research focuses on the synthesis of NiO and CeO2 thin films using spray pyrolysis for the removal of benzoic acid using ozone as an oxidant. The results indicate that the addition of CeO2 films significantly enhances the mineralization of benzoic acid, achieving a rate of over 80% as the CeO2 films react with ozone to produce strong oxidant species, such as hydroxyl radicals, superoxide radicals, and singlet oxygen as demonstrated by the presence of quenchers in the reaction system. The difference in catalytic activity between NiO and CeO2 films was analyzed via XPS technique; specifically, hydroxyl oxygen groups in the CeO2 film were greater in number than those in the NiO film, thus benefitting catalytic oxidation as these species are considered active oxidation sites. The effects of nozzle-substrate distances and deposition time during the synthesis of the films on benzoic acid removal efficiency were also explored. Based on XRD characterization, it was established that the NiO and CeO2 films were polycrystalline with a cubic structure. NiO spherical nanoparticles were well-distributed on the substrate surface, while some pin holes and overgrown clusters were observed in the CeO2 films according to the SEM results. The stability of the CeO2 films after five consecutive cycles confirms their reusability. The retrieval of films is easy because it does not require additional separation methods, unlike the catalyst in powder form. The obtained results indicate that the CeO2 films have potential application in pollutant removal from water through catalytic ozonation.

A tailored and rapid approach for ozonation catalyst design

Catalytic ozonation is widely employed in advanced wastewater treatment owing to its high mineralization of refractory organics. The key to high mineralization is the compatibility between catalyst formulation and wastewater quality. Machine learning can greatly improve experimental efficiency, while fluorescence data can provide additional wastewater quality information on the composition and concentration of organics, which is conducive to optimizing catalyst formulation. In this study, machine learning combined with fluorescence spectroscopy was applied to develop ozonation catalysts (Mn/γ-Al₂O₃ catalyst was used as an example). Based on the data collected from 52 different catalysts, a machine-learning model was established to predict catalyst performance. The correlation coefficient between the experimental and model-predicted values was 0.9659, demonstrating the robustness and good generalization ability of the model. The range of the catalyst formulations was preliminarily screened by fluorescence spectroscopy. When the wastewater was dominated by tryptophan-like and soluble microbial products, the impregnation concentration and time of Mn(NO₃)₂ were less than 0.3 mol L^-1 and 10 h, respectively. Furthermore, the optimized Mn/γ-Al₂O₃ formulation obtained by the model was impregnation with 0.155 mol L^-1 Mn(NO₃)₂ solution for 8.5 h and calcination at 600 °C for 3.5 h. The model-predicted and experimental values for total organic carbon removal were 54.48% and 53.96%, respectively. Finally, the improved catalytic performance was attributed to the synergistic effect of oxidation (•OH and ¹O₂) and the Mn/γ-Al₂O₃ catalyst. This study provides a rapid approach to catalyst design based on the characteristics of wastewater quality using machine learning combined with fluorescence spectroscopy.

Enhanced Catalytic Ozonation by Mn-Ce Oxide-Loaded Al2O3 Catalyst for Ciprofloxacin Degradation

Catalytic ozonation is an effective and promising advanced oxidation technology for organic pollutant removal. Herein, CexMn_1-xO₂ metal oxides loaded on Al₂O₃ catalysts (Mn-Ce/Al₂O₃) were synthesized for catalytic ozonation of the wastewater containing ciprofloxacin. The morphology, crystal structure, and specific surface area of the prepared catalyst were characterized. The characteristics of the Mn-Ce/Al₂O₃ catalyst revealed that the loaded MnO₂ could interfere with the formed CeO₂ crystals and then produced complex CexMn_1-xO₂ oxides. Compared with an ozone-alone system (47.4%), the ciprofloxacin degradation efficiency in the Mn-Ce/Al₂O₃ catalytic ozonation system elevated to 85.1% within 60 min. The ciprofloxacin degradation kinetic rate over the Mn-Ce/Al₂O₃ catalyst is 3.0 times that of the ozone-alone system. The synergetic corporation of redox pairs between Mn(III)/Mn(IV) and Ce(III)/Ce(IV) in the Mn-Ce/Al₂O₃ catalyst could accelerate ozone decomposition to generate active oxygen species and further significantly improve the mineralization efficiency of ciprofloxacin. The work demonstrates the great potential of developing dual-site ozone catalysts for advanced treatment of wastewater.

A comprehensive review on metal based active sites and their interaction with O3 during heterogeneous catalytic ozonation process: Types, regulation and authentication

Heterogeneous catalytic ozonation (HCO) was a promising water purification technology. Designing novel metal-based catalysts and exploring their structural-activity relationship continued to be a hot topic in HCO. Herein, we reviewed the recent development of metal-based catalysts (including monometallic and polymetallic catalysts) in HCO. Regulation of metal based active sites (surface hydroxyl groups, Lewis acid sites, metal redox cycle and surface defect) and their key roles in activating O₃ were explored. Advantage and disadvantage of conventional characterization techniques on monitoring metal active sites were claimed. In situ electrochemical characterization and DFT simulation were recommended as supplement to reveal the metal active species. Though the ambiguous interfacial behaviors of O₃ at these active sites, the existence of interfacial electron migration was beyond doubt. The reported metal-based catalysts mainly served as electron donator for O₃, which resulted in the accumulation of oxidized metal and reduced their activity. Design of polymetallic catalysts could accelerate the interfacial electron migration, but they still faced with the dilemma of sluggish Me^(n+m)+/Meⁿ⁺ redox cycle. Alternative strategies like coupling active metal species with mesoporous silicon materials, regulating surface hydrophobic/hydrophilic properties, polaring surface electron distribution, coupling HCO process with photocatalysis and H₂O₂ were proposed for future research.

Catalytic Ozonation of Norfloxacin Using Co-Mn/CeO2 as a Multi-Component Composite Catalyst

In this study, a Co-Mn/CeO2 composite was prepared through a facile sol-gel method and used as an efficient catalyst for the ozonation of norfloxacin (NOR). The Co-Mn/CeO2 composite was characterized via XRD, SEM, BET and XPS analysis. The catalytic ozonation of NOR by Co-Mn/CeO2 under different conditions was systematically investigated, including the effect of the initial solution’s pH, Co-Mn/CeO2 composite dose, O3 dose and NOR concentration on degradation kinetics. Only about 3.33% of total organic carbon (TOC) and 72.17% of NOR could be removed within 150 min by single ozonation under the conditions of 60 mg/L of NOR and 200 mL/min of O3 at pH= 7 and room temperature, whereas in the presence of 0.60 g/L of the Co-Mn/CeO2 composite under the same conditions, 87.24% NOR removal was obtained through the catalytic ozonation process. The results showed that catalytic ozonation with the Co-Mn/CeO2 composite could effectively enhance the degradation and mineralization of NOR compared to a single ozonation system alone. The catalytic performance of CeO2 was significantly improved by the modification with Mn and Co. Co-Mn/CeO2 represents a promising way to prepare efficient catalysts for the catalytic ozonation of organic polluted water. The removal efficiency of NOR in five cycles indicates that Co-Mn/CeO2 is stable and recyclable for catalytic ozonation in water treatment.

Highly stable and efficient calcined γ-Al2O3 catalysts loaded with MnOx-CeOx for the ozonation of oxytetracycline

Catalytic ozonation with supported metal oxides is a promising strategy for addressing refractory pollutants in wastewater. In this study, γ-Al2O3 supported MnOx-CeOx catalysts (MC1, MC2, and MC3) obtained at different calcination temperatures (400 °C, 550 °C, and 700 °C) were applied as effective catalysts for ozonation and explored the feasibility of the treatment of oxytetracycline (OTC) wastewater. Comparatively, the MC2 possessed the highest molar ratios of Mn3+/Mn4+ (1.60) and Ce3+/Ce4+ (0.96), the largest surface area (273.8 m2 g-1) with a petal-shaped structure, and most abundant surface hydroxyls (3.78 mmol g-1). These physicochemical characteristics benefited the surface reaction and resulted in the acceleration of ozone decomposition, electron transfer, and •OH generation, thereby improving the catalyst's adsorption ability and catalytic activity. The combination with MC2 increased the OTC and COD removal of the ozonation process from 59.1% and 29.0% to 94.7% and 83.3% in 25 min, respectively. By employing electron paramagnetic resonance (EPR) and radical quenching experiments, it was verified that •OH species generation promoted the mineralization of OTC. The possible degradation pathways of OTC were investigated through mass spectrometry, and the route consisted of dehydration, deamination, and demethylation. Moreover, during a 12-day continuous experiment, MC2 catalyst exhibited excellent reusability and catalytic stability, with COD removal efficiencies above 80%.

Mitigation of hazardous toluene via ozone-catalyzed oxidation using MnOx/Sawdust biochar catalyst

This study investigated catalytic ozone oxidation using a sawdust char (SDW) catalyst to remove hazardous toluene emitted from the chemical industry. The catalyst properties were analyzed by proximate, ultimate, nitrogen adsorption-desorption isotherms, Fourier-transform infrared, and X-ray photoelectron spectroscopy analyses. In addition, hydrogen-temperature programmed reduction experiments were conducted to analyze the catalyst properties. The specific area and formation of micropores of SDC were improved by applying KOH treatment. MnOx/SDC-K3 exhibited a higher toluene removal efficiency of 89.7% after 100 min than MnOx supported on activated carbon (MnOx/AC) with a removal efficiency of 6.6%. The higher (O_ads (adsorbed oxygen)+O_v(vacancy oxygen))/O_L (lattice oxygen) and Mn³⁺/Mn⁴⁺ ratios of MnOx/SDC-K3 than those of MnOx/AC seemed to be important for the catalytic oxidation of toluene.

Recent Developments in Activated Carbon Catalysts Based on Pore Size Regulation in the Application of Catalytic Ozonation

Due to its highly developed pore structure and large specific surface area, activated carbon is often used as a catalyst or catalyst carrier in catalytic ozonation. Although the pore structure of activated carbon plays a significant role in the treatment of wastewater and the mass transfer of ozone molecules, the effect is complicated and unclear. Because different application scenarios require catalysts with different pore structures, catalysts with appropriate pore structure characteristics should be developed. In this review, we systematically summarized the current adjustment methods for the pore structure of activated carbon, including raw material, carbonization, activation, modification, and loading. Then, based on the brief introduction of the application of activated carbon in catalytic ozonation, the effects of pore structure on catalytic ozonation and mass transfer are reviewed. Furthermore, we proposed that the effect of pore structure is mainly to provide catalytic active sites, promote free radical generation, and reduce mass transfer resistance. Therefore, large external surface area and reasonable pore size distribution are conducive to catalytic ozonation and mass transfer.

Activation of ozone by peroxymonosulfate for selective degradation of 1,4-dioxane: Limited water matrices effects

The presence of 1,4-dioxane in various water streams poses a threat to the health of human beings. In this study, the oxidative combination of ozone with peroxymonosulfate (PMS) was for the first time used to remove 1,4-dioxane from water. Near complete abatement of 1,4-dioxane was achieved by ozone-PMS after reaction of only 15 min and the degradation kinetics was found to be positively correlated with doses of PMS and ozone. Ozone-PMS oxidation had the optimum performance at slight base pH values. Both sulfate radicals and hydroxyl radicals were generated in ozone-PMS oxidation and these radicals resulted in the degradation of 1,4-dioxane. The effects of common water constituents and real water matrices were investigated. It was found that bicarbonate ions with a concentration up to 10 mM had a slight promoting effect, while either chloride ions or natural organic matter inhibited only slightly the degradation. Meanwhile, no obvious difference in the degradation of 1,4-dioxane was found among the real water matrices and deionized water, which demonstrates that ozone-PMS oxidation has high tolerance and stability. The results from this study demonstrate that ozone-PMS may be a promising technology for the removal of 1,4-dioxane from various water matrices.

Application of Nanocatalysts in Advanced Oxidation Processes for Wastewater Purification: Challenges and Future Prospects

The increase in population demands for industrialization and urbanization which led to the introduction of novel hazardous chemicals in our environment. The most significant parts of these harmful substances found in water bodies remain in the background, causing a health risk to humans and animals. It is critical to remove these toxic chemicals from the wastewater to keep a cleaner and greener environment. Hence, wastewater treatment is a challenging area these days to manage liquid wastes effectively. Therefore, scientists are in search of novel technologies to treat and recycle wastewater, and nanotechnology is one of them, thanks to the potential of nanoparticles to effectively clean wastewater while also being ecologically benign. However, there is relatively little information about nanocatalysts’ applicability, efficacy, and challenges for future applications in wastewater purification. This review paper is designed to summarize the recent studies on applying various types of nanocatalysts for wastewater purification. This review paper highlights innovative work utilizing nanocatalysts for wastewater applications and identifies issues and challenges to overcome for the practical implementation of nanocatalysts for wastewater treatment.

Bifunctional CePO4/CeO2 nanocomposite as a promising heterogeneous catalyst for the enhancement of the ozonation recovery effect in the presence of chloride ions

The degradation of organics through ozonation is strongly reduced by chloride ions. Although the efficiency of such processes can be recovered in the presence of homogeneous phosphates, the addition of these chemicals to water is problematic because of the generation of secondary wastes. Phosphates are known as one of the most important biogens responsible for the eutrophication of rivers and lakes. Thus, their worldwide application should be limited. The main goal of this work was to characterize the performance of solid-state cerium(III) phosphate (CePO₄), cerium dioxide (CeO₂), and bifunctional CePO₄/CeO₂ nanocomposite as substitutes for homogeneous phosphates during the ozonation of benzoic acid (BA) in the presence of chlorides. All solid-state samples used in this study were synthesized by facile hydrothermal method and thoroughly characterized. It was documented that heterogeneous CePO₄ showed significantly better ozonation recovery effect than homogeneous phosphates. It was also established that the process efficiency could be further enhanced by using the bifunctional nanocomposite. Tests with the use of tert-butanol as a hydroxyl radical scavenger revealed that the improved ozonation efficiency in the presence of CePO₄/CeO₂ resulted from the action of HO^• radicals which were the key reactive oxygen species responsible for the recovery of BA degradation in the presence of chlorides.

Advanced catalytic ozonation for degradation of pharmaceutical pollutants-A review

Various chemical treatment techniques are involved in removing refractory organic compounds from water and wastewater using the oxidation reaction of hydroxyl radicals (^•OH). The use of catalysts in advanced catalytic ozonation is likely to improve the decomposition of molecular ozone to generate highly active free radicals that facilitate the rapid and efficient mineralization and degradation of numerous organics. For the degradation of toxic organic pollutants in wastewater, the advanced catalytic ozonation process has been widely applied in recent years. Low utilization efficiency of ozone and ineffective mineralization of organic contaminants by ozone can be remedied with advanced catalytic ozonation. Advanced catalytic ozonation has gained popularity because of these merits. However, homogeneous catalytic ozonation has the disadvantage of producing secondary contaminants from the addition of metallic ions. Heterogeneous catalytic ozonation can overcome this drawback by utilizing metals, metallic oxides, and carbon materials as a catalyst of efficacy and stability. This review discusses various aspects of catalytic ozonation in wastewater treatment of pharmaceutical pollutants, application of catalytic ozonation process in typical wastewater, and prospects in advancing the techniques in heterogeneous catalytic ozonation.

Mechanism of catalytic ozonation for elimination of methyldopa with Fe3 O4 @SiO2 @CeO2 catalyst

In this study, a magnetic nanocatalyst (Fe₃ O₄ @SiO₂ @CeO₂ ) was prepared and applied in the catalytic ozonation of methyldopa (MD). The effects of operational parameters on catalytic ozonation performance were investigated, including ozone dosage, catalyst dosage, initial MD concentration, and pH. The removal of MD was 45.2% in ozonation, whereas the efficiency was achieved to 83.0% with the addition of Fe₃ O₄ @SiO₂ @CeO₂ . The results showed that Fe₃ O₄ @SiO₂ @CeO₂ could significantly improve the catalytic ozonation performance. And the enhanced mechanism study showed that it was attributed to promotion of ozone decomposition to generate hydroxyl radical. The reaction model was explored, and the reaction rates were calculated for the MD degradation in catalytic ozonation. A higher degradation efficiency of MD in catalytic ozonation was attributed to the enhanced surface effect of the catalysts, which was confirmed by using TBA, PO₄ ^3- , and p-BQ as scavengers of hydroxyl radical, surface reaction, and superoxide radical. The hydroxyl radical and superoxide radical played an important role in the degradation of MD. The mechanism of catalytic ozonation by Fe₃ O₄ @SiO₂ @CeO₂ was discussed via X-ray photoelectron spectroscopy (XPS) spectra and experimental data.

Effective mineralization of p-nitrophenol by catalytic ozonation using Ce-substituted La1‒xCexFeO3 catalyst

In this study, cerium-doped lanthanum ferrite perovskite oxides (La_1‒xCe_xFeO₃) with different A-site were synthesized using a sol-gel method and they were used as ozonation catalyst for p-nitrophenol (PNP) mineralization for the first time. Catalytic activity in terms of total organic carbon (TOC) removal followed the order of La_0.8Ce_0.2FeO₃ > La_0.4Ce_0.6FeO₃ > La_0.6Ce_0.4FeO₃ > La_0.2Ce_0.8FeO₃ > LaFeO₃ with 77, 66, 61, 60 and 56% respectively. The synthesized catalysts were characterized by diffraction of X-ray (XRD), Raman spectroscopy, Brunauer-Emmett-Teller (BET) and scanning electronic microscopy (SEM). Moreover, electron spin resonance (ESR) and radicals quenching experiments showed that the active oxygen species in the ozone decomposition process are mainly hydroxyl radical (·OH), and also include superoxide radical (O₂^-) and singlet oxygen (¹O₂). Furthermore, the superior activity of La_0.8Ce_0.2FeO₃ could be attributed to the higher surface area, the richer lattice oxygen, richer surface -OH groups and the facilitated redox Ce³⁺/Ce⁴⁺ and Fe²⁺/Fe³⁺ cycling. In addition, this study provides an insight to use metal-doped perovskite catalysts for catalytic ozonation.

An integrated approach using ozone nanobubble and cyclodextrin inclusion complexation to enhance the removal of micropollutants

Ozone (O₃) has been widely used for the elimination of recalcitrant micropollutants in aqueous environments, due to its strong oxidation ability. However, the utilization efficiency of O₃ is constrained by its low solubility and short half-life during the treatment process. Herein, an integrated approach, using nanobubble technology and micro-environmental chemistry within cyclodextrin inclusion cavities, was studied in order to enhance the reactivity of ozonisation. Compared with traditional macrobubble aeration with O₃ in water, nanobubble aeration achieved 1.7 times higher solubility of O_3, and increased the mass transfer coefficient 4.7 times. Moreover, the addition of hydroxypropyl-β-cyclodextrin (HPβCD) further increased the stability of O₃ through formation of an inclusion complex in its molecule-specific cavity. At a HPβCD:O₃ molar ratio of 10:1, the lifespan of O₃ reached 18 times longer than in a HPβCD-free O₃ solution. Such approach accelerated the removal efficiency of the model micropollutant, 4-chlorophenol by 6.9 times, compared with conventional macrobubble ozonation. Examination of the HPβCD inclusion complex by UV-visible spectroscopy and Nuclear Magnetic Resonance analyses revealed that both O₃ and 4-chlorophenol entered the HPβCD cavity, and Benesi-Hildebrand plots indicated a 1:1 stoichiometry of the host and guest compounds. Additionally, molecular docking simulations were conducted in order to confirm the formation of a ternary complex of HPβCD:4-chlorophenol:O₃ and to determine the optimal inclusion mode. With these results, our study highlights the viability of the proposed integrated approach to enhance the ozonation of organic micropollutants.

Rapid degradation of refractory organic pollutants by continuous ozonation in a micro-packed bed reactor

Recently microreactor technology attracts attention due to the excellent multiphase mixing and enhanced mass transfer. Herein, a continuous ozonation system based on a micro-packed bed reactor (μPBR) was used to improve the dissolution rate of ozone and achieved a rapid and efficient degradation of refractory organic pollutants. The effects of liquid flow rate, gas flow rate, initial pH, initial O₃ concentration and initial phenol concentration on the phenol and chemical oxygen demand (COD) removal efficiencies were also investigated. Experimental results showed that phenol and COD removal efficiencies under optimal conditions achieved 100.0% and 86.4%, respectively. Compared with large-scale reactors, the apparent reaction rate constant in μPBR increased by 1-2 orders of magnitude. In addition, some typical organic pollutants (including phenols, antibiotics and dyes) were treated by ozonation in μPBR. The removal efficiencies of these organic pollutants and COD achieved 100.0% and 70.2%-80.5% within 71 s, respectively. In this continuous treatment system, 100% of the unreacted ozone was converted to oxygen, which promoted the healthy development of aquatic ecosystems. Thus, this continuous system based on μPBR is a promising method in rapid and efficient treating refractory organic pollutants.

Emerging organic contaminants and odorous compounds in secondary effluent wastewater: Identification and advanced treatment

This study aims to address organic micropollutants in secondary effluents from municipal wastewater treatment plants (WWTPs) by first identification of micropollutants in different treatment units, and second by evaluating an advanced treatment process for removals of micropollutants. In secondary effluents, 28 types of pharmaceutical and personal care products (PPCPs), 5 types of endocrine disrupting chemicals (EDCs) and 3 types of odorous compounds are detected with total concentrations of 513 ± 57.8 ng/L, 991 ± 36.5 ng/L, 553 ± 48.3 ng/L, respectively. An integrated process consisting of in-situ ozonation, ceramic membrane filtration (CMF) and biological active carbon (BAC) filtration is investigated in a pilot scale (1000 m³/d) for removal of micropollutants in secondary effluents. The total removal efficiencies of PPCPs, EDCs and odorous compounds are 98.5%, 95.4%, and 91.1%, respectively. Removal mechanisms of emerging organic contaminants (EOCs) and odorous compounds are discussed based on their physicochemical properties. The remarkable removal efficiencies of micropollutants by the pilot system is attributed to synergistic effects of combining ozonation, ceramic membrane filtration and BAC filtration. This study provides a cost-effective and robust technology with the capability of treating secondary effluents for reuse applications.

Recent advances in application of graphitic carbon nitride-based catalysts for degrading organic contaminants in water through advanced oxidation processes beyond photocatalysis: A critical review

Advanced oxidation processes (AOPs) have attracted much interest in the field of water treatment owing to their high removal efficiency for refractory organic contaminants. Graphitic carbon nitride (g-C₃N₄)-based catalysts with high performance and cost effectiveness are promising heterogeneous catalysts for AOPs. Most research on g-C₃N₄-based catalysts focuses on photocatalytic oxidation, but increasingly researchers are paying attention to the application of g-C₃N₄-based catalysts in other AOPs beyond photocatalysis. This review aims to concisely highlight recent state-of-the-art progress of g-C₃N₄-based catalysts in AOPs beyond photocatalysis. Emphasis is made on the application of g-C₃N₄-based catalysts in three classical AOPs including Fenton-based processes, catalytic ozonation and persulfates activation. The catalytic performance and involved mechanism of g-C₃N₄-based catalysts in these AOPs are discussed in detail. Meanwhile, the effect of water chemistry including pH, water temperature, natural organic matter, inorganic anions and dissolved oxygen on the catalytic performance of g-C₃N₄-based catalysts are summarized. Moreover, the reusability, stability and toxicity of g-C₃N₄-based catalysts in water treatment are also mentioned. Lastly, perspectives on the major challenges and opportunities of g-C₃N₄-based catalysts in these AOPs are proposed for better developments in the future research.

Hybrid electrocatalytic ozonation treatment of high-salinity organic wastewater using Ni-Ce/OMC particle electrodes

Hybrid electrocatalytic ozonation is an efficient method for degrading high-salinity organic wastewater that has excellent oxidation ability and is environmentally friendly. Furthermore, the high salt content of the wastewater provides electrolyte to support the process, which avoids secondary pollution caused by the addition of electrolyte. In this work, Ni_0.2-Ce_0.2/ordered mesoporous carbon (OMC)/granular active carbon (GAC) particle electrodes with a Ni:Ce weight ratio of 1:1 were synthesized using a simple method. The electrodes were characterized by transmission electron microscopy and electron paramagnetic resonance spectroscopy, as well as other techniques. The catalytic performance was investigated using cyclic voltammetry and AC impedance. Higher reduction and oxidation peak currents were obtained with the Ni_0.2-Ce_0.2/OMC catalyst than with Ni_0.2/OMC or Ce_0.2/OMC, indicating that the bimetallic catalyst has higher activity for the reduction of O₂ to H₂O₂ and the oxidation of O₃ to ·OH. The order of the k values-which represent the mass-transfer rate-was Ni_0.2-Ce_0.2/OMC (0.157) > Ni_0.2/OMC (0.017) > Ce_0.2/OMC (0.014). The results show that cooperation between Ni, Ce, and OMC promoted the dispersion of Ni and Ce and improved the catalytic performance. Ni_0.2-Ce_0.2/OMC enhances the catalytic reduction of O₂ to H₂O₂, and, in addition, Ce is able to rapidly store and release oxygen through Ce³⁺/Ce⁴⁺ conversions and reacting with O₃ to generate ·OH, which increases the oxidation capacity of the material. Under the optimal conditions the chemical oxygen demand removal for high-salinity organic wastewater using Ni_0.2-Ce_0.2/OMC/GAC particle electrodes reached 93.7%.

Catalytic ozonation for water and wastewater treatment: Recent advances and perspective

Ozonation process has been widely applied in water and wastewater treatment, such as for disinfection, for degradation of toxic organic pollutants. However, the utilization efficiency of ozone is low and the mineralization of organic pollutants by ozone oxidation is ineffective, and some toxic disinfection byproducts (DBPs) may be formed during ozonation process. Catalytic ozonation process can overcome these problems to some extent, which has received increasing attention in recent years. During catalytic ozonation, catalysts can promote O₃ decomposition and generate active free radicals, which can enhance the degradation and mineralization of organic pollutants. In this paper, the history of ozonation application in water treatment was briefly reviewed. The properties of the ozone molecule, the ozonation types and several ozone-based water treatment processes were briefly introduced. Various catalysts for catalytic ozonation, including homogeneous and heterogeneous catalysts, such as metal ions, metal oxidizes, carbon-based materials and their possible catalytic mechanisms were analyzed and summarized in detail. Furthermore, some inconsistent results of previous research on catalytic ozonation were analyzed and discussed. The application of catalytic oxidation for the degradation of toxic organic pollutants, including phenols, pesticides, dyes, pharmaceuticals and others, was summarized. Finally, several key aspects of catalytic ozonation, such as pH effect, the catalyst performance, the catalytic mechanism were proposed, to which more attention should be paid in future study.

The catalytic ozonation of diazinon using nano-MgO@CNT@Gr as a new heterogenous catalyst: the optimization of effective factors by response surface methodology

In this research, the degradation of the insecticide diazinon was studied using a new hybrid catalyst consisting of magnesium oxide nanoparticles (nano-MgO), carbon nanotubes (CNTs), and graphite (Gr), nano-MgO@CNT@Gr, under various experimental conditions. This study shows the optimization of the nano-MgO@CNT@Gr/O3 process for diazinon degradation in aqueous solutions. Box-Behnken experimental design (BBD) and response surface methodology (RSM) were used to assess and optimize the solo effects and interactions of four variables, pH, catalyst loading, reaction time, and initial diazinon concentration, during the nano-MgO@CNT@Gr/O3 process. Analysis of regression revealed an adequate fit of the experimental results with a quadratic model, with R 2 > 0.91. Following the collection of analysis of variance (ANOVA) results, pH, catalyst loading, and reaction time were seen to have significant positive effects, whereas the concentration of diazinon had a considerable negative impact on diazinon removal via catalytic ozonation. The four variables for maximum diazinon removal were found to be optimum (82.43%) at the following levels: reaction time, 15 min; pH, 10; catalyst dosage, 1.5 g L-1; and diazinon concentration, 10 mg L-1. The degradation of diazinon gave six kinds of by-products. The mechanism of diazinon decomposition was considered on the basis of the identified by-products. According to these results, the nano-MgO@CNT@Gr/O3 process could be an applicable technique for the treatment of diazinon-containing wastewater.

Preparation of Carbon Nanotubes with Supported Metal Oxide Nanoparticles: Effect of Metal Precursor on Thermal Decomposition Behavior of the Materials

To develop new catalysts based on carbon nanomaterials with supported metal oxide nanoparticles for oxidative transformations of sulfur compounds, a series of metal oxide nanoparticle-decorated carbon nanotubes (MOx/CNTs) were prepared by incipient wetness impregnation at a variation of the active metal type (M = Ce, Mo, Cu). The thermal decomposition of bulk and CNT supported metal precursors used in the preparation of MOx/CNTs was analyzed under inert atmosphere employing several thermoanalytical techniques (thermogravimetry, differential thermogravimetry and differential scanning calorimetry) coupled with mass spectrometry. The thermolysis parameters of the bulk and supported metal precursors were compared and the effect of CNT support on the decomposition pattern of compounds was elucidated. It was established that the decomposition of metal precursors supported on CNTs was started and completed at temperatures of 15‒25 and 25‒70 °C lower, respectively, compared with the bulk active metal precursor. The enhancement of CNT support stability against thermal degradation is observed in the following row of metal cations: Ce < Cu < Мо < pristine and metal anions of precursor: nitrate < chloride < sulfate. The optimal mode of thermal treatment of catalyst and appropriate active metal precursors were selected for advanced synthesis of nanosized MOx/CNT catalyst.

Catalytic Ozonation of Organics in Reverse Osmosis Concentrate with Catalysts Based on Activated Carbon

Acid-washed activated carbon (AC-A), nitric acid modified activated carbon (AC-NO₂), aminated activated carbon (AC-NH₂) and cerium-loaded activated carbon (Ce/AC) were prepared and characterized by BET procedure, Boehm titration and SEM. Their performances were investigated for the ozonation of p-chlorobenzoic acid (p-CBA) in its solution and organic compounds in reverse osmosis concentrate (ROC). Nitration and amination had little effect on the surface area of catalyst, but increased the concentration of surface acid and basic functional group respectively. After loading Ce, the surface area of the catalyst decreased, and amount of Ce particles were agglomerated on the surface of activated carbon. All the four catalysts can improve the removal rate of the organics in water. Among the four catalysts, Ce/AC shows the highest catalytic activity. The removal rates of p-CBA, TOC and three target pollutants (e.g., tetracycline, metoprolol, atrazine) are 99.6%, 70.38%, 97.76%, 96.21% and 96.03%, respectively. Hydroxyl radical (·OH) was proved to be the core of catalytic reaction mechanism for Ce/AC, with the contribution rate to p-CBA removal of 91.4%. The surface groups and the Ce loaded on AC were the initiator for the rapid generation of ·OH. Electron transfer between electron-rich structures and cerium oxide might be a synergistic effect that can increase catalytic activity of Ce loaded on AC. Catalytic ozonation with Ce/AC is a promising ROC treatment technology due to its efficiency and possibilities for improvement.