Composite hydrogel particles encapsulated ammonium molybdophosphate for efficiently cesium selective removal and enrichment from wastewater

Preparation of HMn2O4 lithium-ion sieves with low manganese dissolution loss for improved cycling stability

Manganese-based lithium-ion sieves have become some of the promising adsorbents for extracting Li+ from brines. However, manganese dissolution loss (MDL) severely impairs the stability and cyclicity of ion sieves. A novel ozone eluent was first developed to extract Li+ from lithium manganese oxides, which decreased MDL decreased from 5.89% to 0.11%, and after ten regeneration cycles, the adsorption capacity retained 85.39% of the initial value, which was better than 55.15% when only hydrochloric acid (HCl) was used as the eluent. Based on these phenomena, the mechanism for the O3 lowering of MDL was investigated. First, the catalytic decomposition reaction of O3 competed with the disproportionation reaction, and the involvement of O3 inhibited the occurrence of the disproportionation reaction. Additionally, the presence of O3 and reactive oxygen species provided a preferential electron acceptor compared to Mn3+ during the migration of electrons from the bulk phase to the surface. In this study, MDL was greatly reduced with a very simple strategy, and the cycling stability of the adsorbent was improved.

Enhanced dye removal using montmorillonite modified with graphene quantum dots in sustainable salep nanocomposite hydrogel

This research investigated the utilization of graphene quantum dot/montmorillonite (GQD/MMT) as an effective nanofiller in a hydrogel composed of salep biopolymer. The semi-IPN hydrogel was synthesized using salep as the substrate, acrylamide (AAm) as the monomer, ammonium persulfate (APS) as an initiator in free radical polymerization, and N,N'-methylenebisacrylamide (MBA) as a cross-linking agent. The hydrogels were applied to remove safranin (SA), methylene blue (MB), crystal violet (CV), methyl green (MG), congo red (CR), and malachite green (MG) dyes from the water. The diverse properties were analyzed using a scanning electron microscope, fourier infrared spectroscopy, mapping, energy dispersive spectroscopy, weighing analysis, X-ray diffraction, and thermal stability analyses. The optimism of the prepared adsorbent in dye absorption was evaluated by measuring the swelling amount, pH impact, adsorbent dosage, and contact time. The adsorption calculations were described using kinetics and isotherm models. The results indicated that the Langmuir isotherm model (R2 = 99.6) and the pseudo-second-order kinetic model (R2 = 99.9) provided the best fit for the absorption process of MB. The presence of additional amounts of GQD/MMT had a reciprocal effect on the adsorption efficiency due to the accumulation of GQD/MMT in the semi-interpenetrating polymer network (semi-IPN (structure. The findings revealed that the samples exhibited high thermal stability, and the absorption process was primarily chemical. Furthermore, the nanocomposite hydrogels demonstrated distinct mechanisms for absorbing anionic dye (CR) and cationic dye (MB). Under optimal conditions, using 7 wt% GQD/MMT at a concentration of 5 ppm, pH = 7, an adsorbent dosage of 50 mg, at room temperature, and a contact time of 90 min, the maximum removal efficiencies were achieved: MB (96.2%), SA (98.2%), MG (86%), CV (99.8%), MG (95.8%), and CR (63.4%). These results highlight the adsorbent's high absorption capacity, rapid removal rate, and reusability, demonstrating its potential as an eco-friendly and cost-effective solution for removing dyes from water.

Adsorption Behavior and Mechanism of Cesium Ions in Low-Concentration Brine Using Ammonium Molybdophosphate-Zirconium Phosphate on Polyurethane Sponge

Salt lake brine originating from Qinghai, China has abundant cesium resources and huge total reserves. The inorganic ion exchangers ammonium molybdophosphate (AMP) and zirconium phosphate (ZrP) have the significant advantages of separating and extracting Cs⁺ as a special adsorbent. Nevertheless, their high solubility in water leads to a decrease in their ability to adsorb Cs⁺ in aqueous solutions, causing problems such as difficulty with using adsorbents alone and a difficult recovery. In this work, an environmentally friendly polyurethane sponge (PU sponge) with a large specific surface area is employed as an adsorbent carrier by physically impregnating dopamine-coated AMP and ZrP onto a PU sponge, respectively. The experiment found that under the same conditions, the AMP/PU sponge performs better than the ZrP/PU sponge for Cs⁺ adsorption. When the amount of adsorbent reaches 0.025 g, the adsorption capacity reaches saturation. The adsorption efficiency remains above 80% when the concentration of Cs⁺ is 5-35 mg/L. The kinetic calculations show that adsorption is spontaneous, feasible, and has a higher driving force at high temperatures. In addition, the power and mechanism of the interaction between adsorbent and adsorbent are explained using the density functional theory calculation. This efficient, stable, and selective Cs⁺ adsorbent provides design guidelines.

The latest research trends in the removal of cesium from radioactive wastewater: A review based on data-driven and visual analysis

The widespread adoption of nuclear energy has increased the amount of radioactive cesium (Cs) that is discharged into waste streams, which can have environmental risks. In this paper, we provide a comprehensive summary of current advances in aqueous Cs removal by employing a bibliometric analysis. We collected 1580 articles related to aqueous Cs treatment that were published on the Web of Science database between 2012 and 2022. By applying bibliometric analysis combined with network analysis, we revealed the research distribution, knowledge base, research hotspots, and cutting-edge technologies in the field of aqueous Cs removal. Our findings indicate that China, Japan, and South Korea are the most productive countries with respect to Cs removal research. In addition, both historic events and environmental threats might have contributed to research in Asian countries having a higher focus on Cs removal as well as strong international cooperation between Asian countries. A detailed keyword analysis reveals the main knowledge base for aqueous Cs removal and highlights the potential of the adsorption-based method for treating Cs contamination. Furthermore, the results reveal that exploration of functional materials is a popular research topic in the field of Cs removal. Since 2012, novel materials, including Prussian blue, graphene oxide, hydrogel and nanocomposites, have been widely investigated because of their high capacity for Cs removal. On the basis of the detailed information, we report the latest research trends on aqueous Cs removal, and propose future research directions and describe the challenges related to effective Cs treatment. This scientometric review provides insights into current research hotspots and cutting-edge trends in addition to contributing to the development of this crucial research field.

Facile degradation of chitosan-sodium alginate-chromium (III) gel in relation to leather re-tanning and filling

Natural polysaccharide hydrogel, exemplified by chitosan‑sodium alginate (CS-SA), has been prevailing in adsorption of chromium (III) (Cr(III)) containing contaminant. However, the traditional desorption of CS-SA-Cr(III) to recycle the adsorbent faces the problems including chemical desorbents secondary pollution, resource waste of the terminal CS-SA adsorbents, and tedious work of reusing the desorbed Cr(III). Herein, the adsorption product, CS-SA-Cr(III) gel, was degraded to CS/SA/Cr(III) sol and applied in leather re-tanning and filling processes directly. To achieve this goal, three degradation methods were used to transform the gel to sol. Due to the excellent overall performance of the CS/SA/Cr(III)-HMD₄ sol (obtained by the hydrothermal-mechanical degradation method for 4 h (HMD₄)), including wide size and distribution range, moderate viscosity (54 ± 3.1 mPa·s), high electronegativity (-38.6 ± 5.8 mV), and good stability, the resultant leather after re-tanning and filling by the sol achieved fascinating properties such as good thermal stability (T_s, 116.8 ± 1.8 °C; T_d, 94.2 ± 1.7 °C), mechanical performance (tensile strength, 6.9 ± 0.52 MPa; elongation at break, 95 ± 3.0 %), and superduper thickening rate (31.8 %). Moreover, the mechanism of good re-tanning and filling effects was deciphered. Therefore, this work intends to overcome the limitation of traditional desorption technology and further realizes the high-valued application of the exhausted CS-SA-Cr(III) in leather re-tanning and filling processes.

Highly selective adsorption and lattice process of cesium by cubic cyanide-based functional materials

Cesium (Cs) is a byproduct of nuclear bombs, nuclear weapons testing, and nuclear fission in nuclear reactors. Cs can enter the human body through food or air and cause lasting damage. Highly efficient and selective removal of ¹³⁷Cs from low-level radioactive effluents (LLREs), which contain many radionuclides and dissolved heavy metal species, is imperative for minimizing LLRE volume, and facilitating their final disposal. Prussian blue analogs (PBAs) have received much attention as materials for the removal of radioactive Cs because of their affinity for adsorbing Cs⁺. In this study, an inexpensive and readily available cyanide-based functional material (PBA_Cu) exhibiting high efficiency and excellent selectivity toward Cs capture was designed through a facile low-temperature co-precipitation process. Nano-PBA_Cu, crystallizing in the cubic space group (Fm-3m (225)), has an average pore size of 6.53 nm; consequently, PBA_Cu can offer abundant atomic occupation sites for capturing and incorporating Cs. Here, the pseudo-second-order kinetic model and Langmuir model fitted well with the adsorption of Cs ⁺ on PBA_Cu, with a maximum capture capacity of 95.75 mg/g within 5 min, confirming that PBA_Cu could rapidly capture Cs ions. PBA_Cu strongly and selectively interacted with Cs even in a simulant containing large Na⁺, NH₄⁺, Ca²⁺, and Mg²⁺ ion concentrations in an aqueous solution. The process of Cs ⁺ adsorption by cyanide-based functional crystals was confirmed to involve the entry of Cs⁺ into cyanide-based functional crystals to replace K⁺ and finally achieve the lattice incorporation of Cs. The current results broaden the lattice theory of radionuclide Cs removal and provide a promising alternative for the immobilization of Cs from radioactive wastewater.

Cesium removal from wastewater: High-efficient and reusable adsorbent K1.93Ti0.22Sn3S6.43

Efficient and quick removal of radioactive Cs⁺ from wastewater is significant for the safe use of nuclear energy and human health. A novel adsorbent K_1.93Ti_0.22Sn₃S_6.43 (KTSS) was developed for Cs⁺ removal from complex natural water systems. The working mechanism of KTSS for removing Cs⁺ was the synergistic effect of ion exchange and the Cs⋯S binding, which was proved by several characterization techniques. KTSS showed ultrafast kinetics for Cs⁺ adsorption within 1 min with a removal rate of 99%. Meanwhile, KTSS exhibited a higher adsorption capacity of 450.12 mg/g than many other adsorbents to remove Cs⁺ and possessed excellent chemical stability in a wide pH range of 3-12. Thanks to the natural affinity arising from the S^2- ligands, KTSS displayed excellent selectivity for Cs⁺ even in different complex water systems. The separation factors between Cs⁺ and the coexisting ions of Na⁺, K⁺, Mg²⁺, Ca²⁺ were ranged from 408.61 to 7448.20. Fortunately, by eluting with NaNO₃ the adsorbent could realize the green regeneration and cyclic utilization. Furthermore, it was found that KTSS had tremendous advantages in the removal of Cs⁺ in comparison with the other adsorbents. Consequently, it should be considered that KTSS obtained in this study has great potential in applying ultrafast and high-efficient removal of Cs⁺ from wastewater.

Highly selective and easily regenerated porous fibrous composite of PSF-Na2.1Ni0.05Sn2.95S7 for the sustainable removal of cesium from wastewater

The removal of ¹³⁷Cs from radioactive wastewater remains a huge challenge due to the interference of many coexisting ions. Several tin chalcogenides (X₂Sn₃Y₇, XNa, K; YTe, Se, S) were synthesized and screened for highly selective cesium removal from radioactive wastewater. It was found that Na₂Sn₃S₇ showed the best adsorption performance for low cesium concentrations. Especially after nickel doping, the adsorption capacity and thermal stability of the adsorbent were significantly enhanced. Its maximum adsorption capacity reached 436.72 mg·g^-1 within only 5 min and adsorption performance kept active in the pH range of 2-12. After being coated with a porous polysulfone (PSF) fiber, the developed PSF-Na_2.1Ni_0.05Sn_2.95S₇ was applied to natural complex water with cesium concentration of 17.58 mg·L^-1. The separation factors between Cs⁺ and competitive ions ranged from 625.21 to 13123.21. It is noteworthy that NaNO₃ was an efficient regenerating agent and can be easily separated from the CsNO₃ mixture for cyclic utilization. Remarkably, only 45 min in each cycle of adsorption and desorption toward cesium was realized, and the adsorption properties hardly decreased even after 50 consecutive cycles. The above advantages make the proposed material an excellent candidate for efficient Cs⁺ removal and enrichment from wastewater.

High-capacity recovery of Cs+ ions by facilely synthesized layered vanadyl oxalatophosphates with the clear insight into remediation mechanism

Radiocesium remediation is of great significance for the sustainable development of nuclear energy and ecological protection. It is very challenging for the effective recovery of ¹³⁷Cs from aqueous solutions due to its strong radioactivity, solubility and mobility. Herein, the efficient recovery of Cs⁺ ions has been achieved by three layered vanadyl oxalatophosphates, namely (NH₄)₂[(VO)₂(HPO₄)₂C₂O₄]·5 H₂O (NVPC), Na₂[(VO)₂(HPO₄)₂C₂O₄]·2 H₂O (SVPC), and K_2.5[(VO)₂(HPO₄)_1.5(PO₄)_0.5(C₂O₄)]·4.5 H₂O (KVPC). NVPC exhibits the ultra-fast kinetics (within 5 min) and high adsorption capacity for Cs⁺ (q_m^Cs = 471.58 mg/g). It also holds broad pH durability and excellent radiation stability. Impressively, the entry of Cs⁺ can be directly visualized by the single-crystal structural analysis, and thus the underlying mechanism of Cs⁺ capture by NVPC from aqueous solutions has been illuminated at the molecular level. This is a pioneering work in the removal of radioactive ions by metal oxalatophosphate materials which highlights the great potential of metal oxalatophosphates for radionuclide remediation.

Enhanced treatment of organic matters in starch wastewater through Bacillus subtilis strain with polyethylene glycol-modified polyvinyl alcohol/sodium alginate hydrogel microspheres

Starch wastewater is a wide range of environmental issues with organic pollutants. A high efficiency and stability hydrogel-organic degradation system was designed via Bacillus Subtilis with Polyethylene glycol (PEG)-modified Polyvinyl alcohol (PVA)/Sodium alginate (SA) hydrogel microspheres. Bacillus subtilis was immobilized on the surface or inside of PEG-modified PVA/SA hydrogels microspheres via physical adsorption. Results showed PEG-modified PVA/SA microspheres had an effect of adsorption on Bacillus subtilis with enhancing bearing rate to 54.22% compared to the blank control group. The effect of microspheres on degradation was remarkable in simulation starch wastewater with a maximum COD removal rate of 93.35% and compared in reality starch wastewater with 90.02% under the optimal condition of pH = 6, 35℃, 20% dosage, 180 rpm. This novel biological method on starch wastewater enhanced tolerance of microorganisms and degradation effect, reflecting safety, effectiveness, and economy with great significance to environmental protection.

The Carboxyl Functionalized UiO-66-(COOH)2 for Selective Adsorption of Sr2

Efficient and selective removal of 90Sr is an important process for the safe use of nuclear energy. Herein, we investigate and assess the Sr2+ adsorption properties of a metal-organic framework UiO-66-(COOH)2 functionalized by non-bonded carboxylic groups. This MOF is an exciting class of free carboxylic functionalized MOFs that combine chemical stability with gas sorption, dye elimination, and conductivity. Specifically, we show that uniformly distributed carboxyl and water stability make it accessible for loading Sr2+ without structural changes. The FTIR spectroscopy, PXRD analysis, XPS, and SEM-EDS studies show excellent stability as well as the strong affinity between -COOH active site and Sr2+. This strong coordination interaction guarantees a high adsorption capacity of 114 mg g-1 within 5 h (pH 5 and 298 K). Combined kinetic and thermodynamic studies show that the surface complexation is strong chemisorption and cost-effective spontaneous process (ΔG = -5.49 kJ mol-1~-2.16 kJ mol-1). The fact that UiO-66-(COOH)2 not only possesses a high adsorption capacity, but also enables selectivity to Sr2+ in the presence of similar radius ions Na+ and K+, prefigures its great potential for the practical treatment of radioactive Sr2+ in polluted water.

Enhanced treatment of organic matter in slaughter wastewater through live Bacillus velezensis strain using nano zinc oxide microsphere

Slaughter wastewater is an important and wide range of environmental issues, and even threaten human health through meat production. A high efficiency and stability microsphere-immobilized Bacillus velezensis strain was designed to remove organic matter and inhibit the growth of harmful bacteria in process of slaughter wastewater. Bacillus velezensis was immobilized on the surface of sodium alginate (SA)/Polyvinyl alcohol (PVA)/Nano Zinc Oxide (Nano-ZnO) microsphere with the adhesion to bio-carrier through direct physical adsorption. Results indicated that SA/PVA/ZnO and SA/ZnO microspheres could inhibit E.coli growth with adding 0.15 g/L nano-ZnO and not affect Bacillus velezensis strain, and the removal the chemical oxygen demand (COD) rates of SA/PVA/ZnO microsphere immobilized cells are 16.99%, followed by SA/ZnO (13.69%) and free bacteria (7.61%) from 50% concentration slaughter wastewater within 24 h at 37 °C, pH 7.0, and 120 rpm, a significant difference was found between the microsphere and control group. Moreover, when the processing time reaches 36 h, COD degradation of SA/PVA/ZnO microsphere is obviously higher than other groups (SA/PVA/ZnO:SA/ZnO:control vs 18.535 : 15.446: 10.812). Similar results were obtained from 30% concentration slaughter wastewater. Moreover, protein degradation assay was detected, and there are no significant difference (SA/PVA/ZnO:SA/ZnO:control vs 35.4 : 34.4: 36.0). The design of this strategy could greatly enhance the degradation efficiency, inhibit the growth of other bacteria and no effect on the activity of protease in slaughter wastewater. These findings suggested that the nano-ZnO hydrogel immobilization Bacillus velezensis system wastewater treatment is a valuable alternative method for the remediation of pollutants from slaughter wastewater with a novel and eco-friendly with low-cost investment as an advantage.

Decontamination of radioactive cesium-contaminated soil/concrete with washing and washing supernatant- critical review

We reviewed washing of radioactive Cs-contaminated concrete and soil based on the fate of Cs in concrete and soil, including sorption materials for treatment of supernatant solution. In non-aged cement materials (the calcium silicate hydration (C-S-H) phase), it was possible to decontaminate Cs using ion exchange with monovalent cations, such as NH₄⁺. The clay components in the soil and aggregates were important factors in optimization of the efficiency and mechanism for Cs decontamination with washing solution. The parameters (reagent component, pH, and temperature) of the washing solution should be determined considering soil mineral type (here, weathered biotite (WB) with vermiculite), since monovalent cations such as NH₄⁺ and K⁺ can inhibit Cs decontamination due to collapse of the hydrated and expanded interlayer regions with cation exchange. In this case, hydrothermal treatment or H₂O₂ dosing was necessary to expand the collapsed interlayer region for Cs removal by washing with cation exchange or organic acids. Acid and a chelating agent significantly enhanced Cs-release with dissolution of the adsorbent layer containing iron and aluminum oxides. The important characteristics of important and emerging sorption materials for treatment of the radioactive Cs-contaminated supernatant after washing treatment are discussed. Sorbents for treatment of washing supernatant are divided in to two main categories. Clay minerals, metal hexacyanoferrates, and ammonium molybdophosphates are discussed in the inorganic class of materials. Hypercrosslinked polymers, supramolecular sorbents, carbon nanotubes, and graphene oxide are covered in the carbon-based sorbents for Cs removal from water.

Novel One-Pot Solvothermal Synthesis of High-Performance Copper Hexacyanoferrate for Cs+ Removal from Wastewater

Efficient removal of radioactive cesium from complex wastewater is a challenge. Unlike traditional precipitation and hydrothermal synthesis, a novel vast specific surface area adsorbent of copper hexacyanoferrates named EA-CuHCF was synthesized using a one-pot solvothermal method under the moderate ethanol media characterized by XRD, SEM, EDS, BET, and FTIR. It was found that the maximum adsorption capacity towards Cs+ was 452.5 mg/g, which is far higher than most of the reported Prussian blue analogues so far. Moreover, EA-CuHCF could effectively adsorb Cs+ at a wide pH range and low concentration of Cs+ in geothermal water within 30 minutes, and the removal rate of Cs+ was 92.1%. Finally, the separation factors between Cs+ and other competitive ions were higher than 553, and the distribution coefficient of Cs+ reached up to 2.343 × 104 mL/g. These properties suggest that EA-CuHCF synthesized by the solvothermal method has high capacity and selectivity and can be used as a candidate for Cs+ removal from wastewater.

Effective removal of 137Cs ions from radioactive wastewater by Melamine-Styrene based Polymer (MSP)

Cesium (Cs) is a major product of uranium fission, which is one of the most existed radionuclides in radioactive wastes. Removal of Cs-137 has a critical role in the decontamination of liquid radioactive waste due to its half-life of 30.17 years. Concordantly, melamine styrene based conjugated polymer (MSP) was designed, synthesized, and characterized with FTIR, TGA, SEM and BET measurements. The novelty of the study is that the MSP adsorbent is designed as a highly conjugated structure to have better interaction with Cs over the Cs-π bond of the benzene groups of the adsorbent. In this work, the adsorption behavior and rate of MSP were investigated as parameters of adsorbent amount, pH, contact time, particle size, initial Cs⁺ concentration, and temperature. Besides, the adsorption efficiency of Cs-137 was examined by Gamma Spectroscopy. Adsorption results were fitted to three different isotherms which were Freundlich, Langmuir and Dubinin-Radushkevich (D-R). The maximum adsorption capacity of polymer for Cs⁺ ion was found from Langmuir isotherm as 78 mg g^-1. As a part of kinetic parameters, pseudo first and second orders were investigated and in terms of the correlation coefficient pseudo second order was much more appropriate for adsorption of Cs-137 onto MSP.

Prussian blue analogs-based layered double hydroxides for highly efficient Cs+ removal from wastewater

In this work, novel Prussian blue analogs-based layered double hydroxide (PBA@ZnTi-LDH) was in situ synthesized and used for radioactive Cs⁺ removal from wastewater. The results suggested that this PBA@ZnTi-LDH prepared using LDH as skeleton and transition metal source showed higher adsorption capacity (243.9 mg/g) and water stability than conventional PBAs, and promising application in scale-up Cs⁺ removal. Thus, it was granulated by calcium alginate and the PBA@ZnTi-LDH/CaALG exhibited favorable post-separation and fixed-bed adsorption ability at different Cs⁺ concentrations and flow rates, highlighting its application perspective on Cs⁺ removal from various kinds of wastewater. Moreover, the real-world Cs⁺ removal was preliminarily explored using natural complex Cs⁺-containing water. As a result, this stable and easily separated PBA@ZnTi-LDH/CaALG showed high removal efficiency, selectivity and good reusability, which was promising in scale-up Cs⁺ removal from the real-world wastewater.

Rapid and selective removal of Cs+ from water by layered potassium antimony thiostannate

¹³⁷Cs is radioactive and highly hazardous to human health and the environment and its efficient removal from water is still challenging. In this study, potassium antimony tin sulfide (KATS-2) was synthesized using a hydrothermal method and utilized for the first time for cesium removal from water. KATS-2 showed a high maximum ion exchange capacity (358 mg g^-1) and distribution coefficient (1.59 × 10⁵ mL g^-1) toward Cs⁺. In particular, KATS-2 showed rapid ion exchange kinetics and reached the adsorption equilibrium within 5 min with 99% removal efficiency. The adsorption was good at a wide active pH range (1-12) even in extreme alkaline conditions (K_d = 3.26 × 10⁴ mL g^-1 at pH 12). The effect of coexisting ions was also investigated, and a high selectivity toward Cs⁺ was maintained even in artificial seawater (K_d = 3.28 × 10³ mL g^-1). Powder X-ray diffraction and thermogravimetric analysis demonstrated that KATS-2 was chemically and thermally stable. The results showed that owing to its excellent adsorption performance as well as chemical and thermal stability, KATS-2 is a promising adsorbent for Cs⁺ removal from contaminated water.

Prediction and optimization of adsorption properties for Cs+on NiSiO@NiAlFe LDHs hollow spheres from aqueous solution: Kinetics, isotherms, and BBD model

In this work, novel NiSiO@NiAlFe layered double hydroxides (LDHs) hollow spheres were prepared by hydrothermal method. It was worth noting that LDHs' grafting towards NiSiO hollow spheres could avoid the LDHs' aggregation, and thus enhanced the material's adsorption capacity. Furthermore, adsorption kinetics, adsorption isotherms, and Box-Behnken Design (BBD) model were conducted. Results indicated that NiSiO@NiAlFe LDHs hollow spheres had sufficient adsorption capability towards Cs⁺. The adsorption kinetics satisfied the pseudo-second-order adsorption model, Temkin model and Langmuir isotherm model. The adsorption process was efficient at the alkaline condition (pH = 10). The adsorption kinetics indicated that the adsorption process could reach the equilibrium in only 20 min. The maximum adsorption capacity of Cs⁺ towards NiSiO@NiAlFe LDHs hollow spheres was estimated to be 61.5 mg g^-1. Moreover, the adsorption thermodynamics indicated that the adsorption process was exothermal, feasible and spontaneous. Thus, NiSiO@NiAlFe LDHs hollow spheres presented a broad potential for treating cesium containing wastewater.

Enhanced kinetics and super selectivity toward Cs+ in multicomponent aqueous solutions: A robust Prussian blue analogue/polyvinyl chloride composite membrane

Developing effective adsorbents for ¹³⁷Cs removal from complex wastewater systems has been a significant challenge. Although existing spheres adsorbents could improve the post-separation ability and practical operability, the adsorption kinetics are still significantly retarded due to the large intra-particle diffusion resistance. Here, we demonstrate the efficiency of a robust Prussian blue analogue/polyvinyl chloride composite membrane (PPM), which was easily prepared by a simple solvent evaporation method. In virtue of the less dense layer and ion-sieving functionality, it showed enhanced kinetics (5 h) and super selectivity (S_F = 248.3-5388.6) towards Cs⁺. New PPM was robust within a wide pH range (2-10) and exhibited favorable removal capacity (152.8 mg/g), placing it at an outstanding material for Cs⁺ removal among other adsorbents. Moreover, PPM could be simply eluted and reused using a KCl solution as eluent. A study of the adsorption mechanism confirmed an ion-exchange action during the removal process. Thus, PPM is considered to be a promising candidate for the removal of Cs⁺ from multicomponent aqueous solutions.

Bio-Inspired Preparation of Clay-Hexacyanoferrate Composite Hydrogels as Super Adsorbents for Cs. ACS APPLIED MATERIALS & INTERFACES 2020;12:33173-33185. [PMID: 32531151 DOI: 10.1021/acsami.0c06598]

A facile and low-cost fabrication route, inspired by the adhesive proteins secreted by mussels, has been developed to prepare a clay-based composite hydrogel (DHG(Cu)) containing hexacyanoferrate (HCF) nanoparticles for the selective removal of Cs⁺ from contaminated water. Initially, montmorillonite was exfoliated prior to coating with a thin layer of polydopamine (PDOPA) via the self-polymerization of dopamine. Mixing the composite (D-clay) with the HCF precursor, followed by the addition of copper ions, led to the self-assembly of the polymer-coated exfoliated clay nanosheets into a three-dimensional network and in situ growth of KCuHCF nanoparticles embedded within the gel structure. Analytical characterization verified the fabrication route and KCuHCF immobilization by a copper-ligand complexation. Rheology testing revealed the composite hydrogel to be elastic under low strain and exhibited reversible, self-healing behavior following high strain deformation, providing a good retention of KCuHCF nanoparticles in the membrane. The adsorbent DHG(Cu) showed a superior Cs⁺ adsorption capacity (∼173 mg/g), with the performance maintained over a wide pH range, and an excellent selectivity for Cs⁺ when dispersed in seawater at low concentrations of 0.2 ppm. On the basis of its excellent mechanico-chemical properties, the fabricated hydrogel was tested as a membrane in column filtration, showing excellent removal of Cs⁺ from Milli-Q water and seawater, with the performance only limited by the fluid residence time. For comparison, the study also considered other composite hydrogels, which were fabricated as intermediates of DHG(Cu) or fabricated with Fe³⁺ as the cross-linker and reactant for HCF nanoparticle synthesis.

Nanoscale Pisum sativum pods biochar encapsulated starch hydrogel: A novel nanosorbent for efficient chromium (VI) ions and naproxen drug removal

Assembly of novel ecofriendly and sustainable (N-PSPB/SHGL) nanosorbent was fabricated based on encapsulation of derived nanoscale spherical biochar from Pisum sativum pods (N-PSPB) with starch hydrogel (SHGL). The mass ratio between starch and N-PSPB was examined and 2% (w/w) was selected as the optimum percentage for fabrication of the assembled hydrogel. High swelling capacity was characterized by N-PSPB/SHGL nanosorbent (500.0%) at room temperature (25 °C), excellent stability for ten cycles with respect to regeneration by 0.1 mol L-1 HCl. Additionally, characterizations of N-PSPB/Starch nanosorbent were established by SEM and BET measurement to characterize surface area (226.94 m2/g) and pore volume (9.88 cm3/g). The N-PSPB/SHGL nanosorbent was subjected to extensive investigations to evaluate its efficiency for removal of naproxen drug (NAP) and chromium (VI). The Cr(VI) and NAP drug adsorptions were fitted to pseudo-second kinetic and correlated with Langmuir isotherm. The adsorption processes were spontaneous and endothermic based on thermodynamic study.

Superhydrophilic and highly elastic monolithic sponge for efficient solar-driven radioactive wastewater treatment under one sun

As an effective way to obtain solar energy and separate the soluble contaminants from water, solar-driven interfacial evaporation is used in desalination, wastewater treatment, electricity generation, and domestic water heating system. Herein, we demonstrate a monolithic sponge with three-dimensional porous structure as the solar-energy evaporator, which is composed of hydrophilic polymer (Konjac Glucomannan, KGM) and solar absorbent (reduced graphene oxide, rGO). Under one sun irradiation, the sponge achieves a rapid evaporation rate (1.60 kg m^-2 h^-1) and high interfacial water evaporation efficiency (92 %) due to its good absorption, photothermal, thermal insulation, and fast water transport properties. Meanwhile, the concentrations of radioactive elements (strontium, cesium, and uranium) in wastewater dropped from grams to micrograms after purification, even under radiation and acidic conditions. Additionally, the durability and repeatability of the sponge also have been verified. The results showed that solar-driven interfacial evaporation can effectively treat radioactive wastewater and enrich various radionuclides in a more energy-saving manner.

Highly ordered macroporous silica dioxide framework embedded with supramolecular as robust recognition agent for removal of cesium

Owning to highly mechanical strength and non-interference effectivity, silica dioxide is often explored as a stable supporter commonly with mesopore. It is known that a macroporous framework has larger mass transfer channel, possibly beneficial to adsorption process. Herein highly ordered macroporous silica dioxide framework (homogeneous pore size of 194.20 nm) was synthesized and embedded with supramolecular (CC/OMS). Cs cation adsorption onto CC/OMS was explored under different pH (presence or absence of humic acid), initial cesium concentration, shaking time, competing ions. The robust cesium uptake capacity demonstrated by a theory adsorption amount of 150.01 mg/g highlighted unique CC/OMS properties combining large mass transfer channel and superior complex capacity of supramolecular. The adsorption was well fit with Langmuir and pseudo-second-order model. Sodium and potassium at a lower concentration showed little influence on cesium adsorption. The results demonstrated that CC/OMS was an alternative material for cesium capture from acidic aqueous solution.

Facile Synthesis of Porous Polymer Using Biomass Polyphenol Source for Highly Efficient Separation of Cs+ from Aqueous Solution

In this work, a series of polyphenol porous polymers were derived from biomass polyphenols via a facile azo-coupling method. The structure and morphologies of the polymer were characterized by BET, TEM, SEM, XRD, TGA and FT-IR techniques. Batch experiments demonstrated their potentialities for adsorptive separation of Cs⁺ from aqueous solution. Among them, porous polymers prepared with gallic acid as starting material (GAPP) could adsorb Cs⁺ at wide pH value range effectively, and the optimal adsorption capacity was up to 163.6 mg/g, placing it at top material for Cs⁺ adsorption. GAPP exhibited significantly high adsorption performance toward Cs⁺ compared to Na⁺ and K⁺, making it possible in selective removal of Cs⁺ from ground water in presence of co-existing competitive ions. Moreover, the Cs-laden GAPP could be facilely eluted and reused in consecutive adsorption-desorption processes. As a result, we hope this work could provide ideas about the potential utilization of biomass polyphenol in environmental remediation.

Robust and recyclable sodium carboxymethyl cellulose-ammonium phosphomolybdate composites for cesium removal from wastewater

A novel, facilely prepared, recyclable sodium carboxymethyl cellulose-ammonium phosphomolybdate composite (CMC-AMP) was synthesized by chemical cross-linking and used for Cs+ removal. The effects of adsorbent dosage, pH value, initial Cs+ concentration, contact time, temperature and competitive ions on adsorption were investigated. The results showed that CMC-AMP with good mechanical properties could effectively adsorb Cs+ in a wide pH range. In addition, the adsorption process of CMC-AMP was better fitted with the Lagergren first-second model and Langmuir isotherm model. Furthermore, CMC-AMP can be reused five times using ammonium chloride as the eluent without an obvious decrease in absorption activity. The results reveal that CMC-AMP can be used as a low cost and recyclable Cs+ adsorbent.

Magnetophoretic Harvesting of Nannochloropsis oculata Using Iron Oxide Immobilized Beads

In this work, the harvesting of Nannochloropsis oculata microalgae through the use of nanosized Fe3O4 immobilized in polyvinyl alcohol (PVA)/sodium alginate (SA) as a flocculant (Fe3O4/PS) is investigated. Using the Fe3O4/PS immobilized beads could reduce the amount of soluble ferrous ions (Fe2+) released from naked Fe3O4 in acid treatment, leading to easy recovery. The characterization was performed under different dosages and pH values of Fe3O4/PS. The results show that the Fe3O4/PS, when applied to the algae culture (500 mg dry cell weight/L), achieves a 96% harvesting efficiency under conditions of a pH of 4 with 200 mT magnetic field intensity. Fe3O4/PS can be directly reused without adjusting the pH value. The recycled Fe3O4/PS shows stability in terms of its surface properties, maintaining more than 80% harvesting efficiency after five recycles. Magnetophoretic harvesting, using immobilized magnetic iron oxide as a particle-based flocculant, is a potential method to reduce challenges related to the cost-effective microalgae-harvesting method.

Porous composite CMC–KCuFC–PEG spheres for efficient cesium removal from wastewater

Highly stable porous composite CMC–KCuFC–PEG was used for Cs⁺ recovery from wastewater, and showed excellent adsorption performance.