Novel M (Mg/Ni/Cu)-Al-CO3 layered double hydroxides synthesized by aqueous miscible organic solvent treatment (AMOST) method for CO2 capture

Ca-Based Layered Double Hydroxides for Environmentally Sustainable Carbon Capture

The process of carbon dioxide capture typically requires a large amount of energy for the separation of carbon dioxide from other gases, which has been a major barrier to the widespread deployment of carbon capture technologies. Innovation of carbon dioxide adsorbents is herein vital for the attainment of a sustainable carbon capture process. In this study, we investigated the electrified synthesis and rejuvenation of calcium-based layered double hydroxides (Ca-based LDHs) as solid adsorbents for CO2. We discovered that the particle morphology and phase purity of the LDHs, along with the presence of secondary phases, can be controlled by tuning the current density during electrodeposition on a porous carbon substrate. The change in phase composition during carbonation and calcination was investigated to unveil the effect of different intercalated anions on the surface basicity and thermal stability of Ca-based LDHs. By decoupling the adsorption of water and CO2, we showed that the adsorbed water largely promoted CO2 adsorption, most likely through a sequential dissolution and reaction pathway. A carbon capture capacity of 4.3 ± 0.5 mmol/g was measured at 30 °C and relative humidity of 40% using 10 vol % CO2 in nitrogen as the feed stream. After CO2 capture occurred, the thermal regeneration step was carried out by directly passing an electric current through the conductive carbon substrate, known as the Joule-heating effect. CO2 was found to start desorbing from the Ca-based LDHs at a temperature as low as 220 °C as opposed to the temperature above 700 °C required for calcium carbonate that forms as part of the Ca-looping capture process. Finally, we evaluated the cumulative energy demand and environmental impact of the LDH-based capture process using a life cycle assessment. We identified the most environmentally concerning step in the process and concluded that the postcombustion CO2 capture using LDH could be advantageous compared with existing technologies.

Remediation of Cu and As contaminated water and soil utilizing biochar supported layered double hydroxide: Mechanisms and soil environment altering

Preparing materials for simultaneous remediation of anionic and cationic heavy metals contamination has always been the focus of research. Herein a biochar supported FeMnMg layered double hydroxide (LDH) composites (LB) for simultaneous remediation of copper and arsenic contamination in water and soil has been assembled by a facile co-precipitation approach. Both adsorption isotherm and kinetics studies of heavy metals removal by LB were applied to look into the adsorption performance of adsorbents in water. Moreover, the adsorption mechanisms of Cu and As by LB were investigated, showing that Cu in aqueous solution was removed by the isomorphic substitution, precipitation and electrostatic adsorption while As was removed by complexation. In addition, the availability of Cu and As in the soil incubation experiments was reduced by 35.54%-63.00% and 8.39%-29.04%, respectively by using LB. Meanwhile, the addition of LB increased the activities of urease and sucrase by 93.78%-374.35% and 84.35%-520.04%, respectively, of which 1% of the dosage was the best. A phenomenon was found that the richness and structure of microbial community became vigorous within 1% dosage of LB, which indirectly enhanced the passivation and stabilization of heavy metals. These results indicated that the soil environment was significantly improved by LB. This research demonstrates that LB would be an imaginably forceful material for the remediation of anionic and cationic heavy metals in contaminated water and soil.

Simultaneous immobilization of arsenic, lead and cadmium by magnesium-aluminum modified biochar in mining soil

Owing to the human activities such as smelting and mining, arsenic (As), lead (Pb) and cadmium (Cd) seriously polluted the soil of non-ferrous metal mining areas, thus efficient methods for the simultaneous immobilization of the three heavy metals are urgently needed. In the present study, Mg-Al modified biochars (MABs) were synthesized through a simple one-pot pyrolysis method to immobilize the three heavy metals. According to the BET (Brunauer-Emmett-Teller) test method, MABs had larger specific surface areas than biochar. Compared to the materials obtained at 300 °C and 700 °C, MAB with a pyrolysis temperature of 500 °C (MAB 500) had a significant immobilization effect on As, Pb and Cd in the Gansu mining area. Compared with BC, the removal efficiencies of As, Pb and Cd increased from -62%, 17% and 5% to 52%, 100% and 66%, respectively. And the toxicity characteristic leaching procedure (TCLP) test showed that the leaching concentrations of the three heavy metals in the treated soil were all lower than the standard value. X-ray photoelectron spectroscopy and kinetic experiments showed that there were various mechanisms in the immobilization process of the three heavy metals, and the large specific surface area and the multi-Mg/Al-OH of MABs play an important role in this process. More charges were provided by larger specific surface for ion exchange with heavy metals. In addition, larger specific surface area also provided more adsorption sites. More complex sites were provided by Mg/Al-OH to form Mg/Al-O-M then immobilize the heavy metals. In summary, the immobilization mechanism may involve electrostatic attraction, precipitation/co-precipitation, and surface complexation.

Kinetic Modeling-Assisted Mechanistic Understanding of the Catalytic Ozonation Process Using Cu-Al Layered Double Hydroxides and Copper Oxide Catalysts

In this study, copper aluminum layered hydroxides (Cu-Al LDHs) and copper oxide (CuO) were utilized as catalysts for heterogeneous catalytic ozonation (HCO). Target compounds oxalate and formate were used with removal by adsorption and oxidation quantified to elucidate the role of the catalyst in contaminant removal. Oxidation of oxalate mostly occurred on the catalyst surface via interaction of surface oxalate complexes with surface-located oxidants. In contrast, the oxidation of formate occurred in the bulk solution as well as on the surface of the catalyst. Measurement of O₃ decay kinetics coupled with fluorescence microscopy image analysis corresponding to 7-hydroxycoumarin formation indicates that while surface hydroxyl groups in Cu-Al LDHs facilitate slow decay of O₃ resulting in the formation of hydroxyl radicals on the surface, CuO rapidly transforms O₃ into surface-located hydroxyl radicals and/or other oxidants. Futile consumption of surface-located oxidants via interaction with the catalyst surface was minimal for Cu-Al-LDHs; however, it becomes significant in the presence of higher CuO dosages. A mechanistic kinetic model has been developed which adequately describes the experimental results obtained and can be used to optimize the process conditions for the application of HCO.

Advances in the Use of Nanocomposite Membranes for Carbon Capture Operations

The adoption of nanodoped membranes in the areas of gas stream separation, water, and wastewater treatments due to the physical and operational advantages of such membranes has significantly increased. The literature has shown that the surface structure and physicochemical properties of nanodoped membranes contribute significantly to the interaction and rejection characteristics when compared to bare membranes. This study reviews the recent developments on nanodoped membranes, and their hybrids for carbon capture and gas separation operations. Features such as the nanoparticles/materials and hybrids used for membrane doping and the effect of physicochemical properties and water vapour in nanodoped membrane performance for carbon capture are discussed. The highlights of this review show that nanodoped membrane is a facile modification technique which improves the membrane performance in most cases and holds a great potential for carbon capture. Membrane module design and material, thickness, structure, and configuration were identified as key factors that contribute directly, to nanodoped membrane performance. This study also affirms that the three core parameters satisfied before turning a microporous material into a membrane are as follows: high permeability and selectivity, ease of fabrication, and robust structure. From the findings, it is also observed that the application of smart models and knowledge-based systems have not been extensively studied in nanoparticle-/material-doped membranes. More studies are encouraged because technical improvements are needed in order to achieve high performance of carbon capture using nanodoped membranes, as well as improving their durability, permeability, and selectivity of the membrane.

Carbon dioxide capture in biochar produced from pine sawdust and paper mill sludge: Effect of porous structure and surface chemistry

The CO₂ concentration in the atmosphere is increasing and threatening the earth's climate. Selective CO₂ capture at large point sources will help to reduce the CO₂ emissions to the atmosphere. Biochar with microporous structure could be a potential material to capture CO₂. The impact of feedstock type, pyrolysis temperature and steam activation of biochars were evaluated for CO₂ adsorption capacity. Pine sawdust biochars were produced at 550 °C, and steam activated for 45 min at the same temperature after completing the pyrolysis (PS550 and PSS550). Paper mill sludge biochars were produced at 300 and 600 °C (PMS300 and PMS600). The CO₂ adsorption capacity of biochars was tested at 25 °C using a volumetric sorption analyzer. Pine sawdust biochars showed significantly higher CO₂ adsorption capacity than paper mill sludge biochars due to high surface area and microporosity. Pine sawdust biochars were then evaluated for dynamic adsorption under representative post-combustion flue gas concentration conditions (15% CO₂, 85% N₂) using a breakthrough rig. Both materials showed selective CO₂ uptake over N₂ which is the major component along with CO₂ in flue gas. PSS550 had slightly higher CO₂ adsorption capacity (0.73 mmol g^^-1 vs 0.67 mmol g^^-1) and CO₂ over N₂ selectivity (26 vs 18) than PS550 possibly due to increase of microporosity, surface area, and oxygen containing basic functional groups through steam activation. Pine sawdust biochar is an environmentally friendly and low-cost material to capture CO₂.

Correlations of acidity-basicity of solvent treated layered double hydroxides/oxides and their CO2 capture performance

The basicity and acidity of solvent-treated layered double hydroxide (ST-LDHs) and their layered double oxides (ST-LDOs) have been fully studied using Hammett titration, in situ FTIR, CO₂-TPD and NH₃-TPD. Five solvents (ethanol, acetone, isopropanol, ethyl acetate and 1-hexanol) were selected to treat [Mg_0.72Al_0.28(OH)₂](CO₃)_0.14 (Mg_2.5Al-CO₃ LDH) and compared with traditional LDH co-precipitated from water. The Brønsted basicity strength of the ST-LDHs and ST-LDOs increased but was accompanied by a decrease in basic site density. In addition, the Lewis acidity of ST-LDOs also changes significantly, with medium strength Lewis acid sites dissapearing after solvent treatment. We found that the CO₂ capture capacity of solvent treated LDOs is 50% higher than that of traditional co-precipitated LDO sample. The ethanol treated LDO exhibited the highest CO₂ uptake of 1.01 mmol g^-1. The observed CO₂ capture performance of the ST-LDOs correlates linearly with the ratio of total acid sites to total basic sites.

Mechanochemical synthesis of Fe2O3/Zn-Al layered double hydroxide based on red mud

In this work, using industrial waste red mud (RM) as main starting material, a simple method of mechanochemical synthesis (MCS) was introduced as a green approach to synthesize heterogeneous Fe₂O₃/Zn-Al layered double hydroxide (F/ZA-LDH), which could be used as a new low-cost catalyst for photo-Fenton reaction. The optimum preparation conditions of F/ZA-LDH were as follows: mass ratio of Zn(NO₃)₂·6H₂O to RM (m_Zn:m_RM) 2:1, dry milling time 6 h, H₂O dosage 2 mL, ball-to-powder mass ratio 50:1, and milling speed 250 rpm. The effects of the synthesis conditions on the crystal structure and catalytic activity of F/ZA-LDH were analyzed. The F/ZA-LDH was characterized by XRD, TG, XPS, SEM, (HR)TEM. The characterization results showed the composite had a crystallized hydrotalcite-like structure, and the crystalline phases in the optimum F/ZA-LDH were Fe₂O₃ and Zn-Al LDH. A hetero-interfaces between Fe₂O₃ and Zn-Al LDH existed in the synthesized Fe₂O₃/Zn-Al LDH composite. Furthermore, the possible mechanism for F/ZA-LDH formation in the MCS process was proposed. Overall, our results provide a systematic understanding of the preparation of LDH composite through MCS using RM as main material, and our findings help to develop green technology for reusing RM.

Photocatalytic degradation of gemifloxacin antibiotic using Zn-Co-LDH@biochar nanocomposite

The aim of the present study was to investigate the photocatalytic performance of biochar (BC)-incorporated Zn-Co-layered double hydroxide (LDH) nanostructures in gemifloxacin (GMF) degradation as a model pharmaceutical pollutant. The as-prepared Zn-Co-LDH@BC showed high photocatalytic efficiency due to the enhanced separation of photo-generated charge carriers using cobalt hydroxide as well as inhibiting the agglomeration of LDH nanostructures by incorporation of BC. According to the results, 92.7% of GMF was degraded through photocatalysis in the presence of Zn-Co-LDH catalyst. The photocatalytic performance of BC-incorporated Zn-Co-LDH was highly dependent on the solute concentration and photocatalyst dosage. The addition of ethanol caused more inhibiting effect than that of benzoquinone (BQ), indicating the major role of ^•OH in decomposition of GMF compared to the negligible role of O₂^•-. A greater enhancement in the photocatalytic degradation of GMF was obtained when the photoreactor containing Zn-Co-LDH@BC nanostructures was oxygenated. Less than 10% drop in the removal efficiency of GMF was observed within five successive operational runs. The results of chemical oxygen demand (COD) analysis indicated the COD removal efficiency of about 80% within 200 min, indicating the acceptable mineralization of GMF. The reaction pathways were also proposed for the photocatalytic conversion of GMF under UV light irradiation.

Insight into the enhanced catalytic activity of a red mud based Fe2O3/Zn–Al layered double hydroxide in the photo-Fenton reaction

In this work, the enhanced catalytic activity of red mud based Fe₂O₃/Zn–Al layered double hydroxide in the photo-Fenton reaction has been studied in detail.