Selective removal of anionic dyes with exceptionally high adsorption capacity and removal of dichromate (Cr2O72-) anion using Ni-Co-S/CTAB nanocomposites and its adsorption mechanism

A comparative study on the malachite green dye adsorption of chemically synthesized and green MgFe2O4 nanoparticles using gerbera floral waste extract

The situation of discharging a large amount of dyes from the textile industries has caused many adverse effects on human health and the ecosystems. Emerging bio-nanomaterials represent a new trend in efficient dye removal in aqueous media. Herein, we mention that MgFe2O4 bioprepared using gerbera extract has been successfully used to adsorb malachite green (MG) in water. A comparison was made to determine the dye removal efficiency between biogenic MgFe2O4 (MFOB) and chemical MgFe2O4 (MFOC). The spherical MFOB material exhibited a large surface area of 85.0 m2 g-1 and high crystallinity. The obtained outcomes showed that the highest adsorption capacity of MG dye was 584.49 mg g-1 at a MFOB dose of 0.05 g L-1 and MG concentration of 10 mg L-1. Higher correlation coefficients in the Langmuir isotherm suggested monolayer adsorption of MG. The Box-Behnken design and response surface method were established to optimize MG removal percentage under the conditions, i.e., initial MG concentration (10-30 mg L-1), adsorbent dose (0.02-0.08 g L-1), and pH of dye solution (6-8). MFOB had good reusability with high removal efficiencies after three continuous cycles. Post reuse, this adsorbent still showed excellent stability through the verification of their structural properties in comparison with fresh MFOB, showing potential for practical applications.

Schiff base crosslinked graphene/oxidized nanofibrillated cellulose/chitosan foam: An efficient strategy for selective removal of anionic dyes

A versatile foam based on Schiff base crosslinking of oxidized nanofibrillated cellulose (ONFC) with amino modified graphene oxide (NGO) and chitosan (CS) was prepared for the efficacious selective removal of anionic dyes. (3-aminopropyl) triethoxysilane (APTES) was employed as a surface modifier to yield an amino modified graphene oxide (NGO). Meanwhile, ONFC was obtained via a periodate oxidation process to produce dialdehyde groups. Thus, the Schiff base crosslinking of ONFC with NGO and CS enabled to be readily accomplished, producing a versatile NGO/ONFC/CS foam. Systematical characterizations confirmed the successful covalent crosslinking and formation of NGO/ONFC/CS foams. Selective adsorption of Allura Red (AR) and orange G (OG) over cationic dye methylene blue (MB) by NGO/ONFC/CS was confirmed. It was found the maximum adsorption capacities of AR and OG at 303 K were 416.7 and 300.5 mg g-1, while it was 14.60 mg g-1 for MB. Thus, the new Schiff base crosslinked NGO/ONFC/CS paves the way for developing versatile graphene based foams in the applications of water treatment.

Surfactant supported chitosan for efficient removal of Cr(VI) and anionic food stuff dyes from aquatic solutions

In order to develop a novel and cost-effective adsorbent with outstanding adsorption capacity and excellent recyclability for anionic pollutants, the chitosan-modified cetyltrimethylammonium bromide sorbent (CS@CTAB) was fabricated. Fourier-transform infrared spectroscopy, N2 adsorption-desorption isotherm, elemental analysis, Thermogravimetric analysis, X-ray diffraction, and Scanning electron microscopy have been applied to evaluate both raw and surfactant modified chitosan (CS@CTAB). Azorubine, Sunset Yellow, and hexavalent chromium were used to study the adsorption behavior of CS@CTAB under various parameters such as adsorbent dose, initial dye and metal ion concentration, contact time, and temperature. Adsorption equilibrium, kinetics models and thermodynamic parameters were investigated. The adsorption isotherm fitted well with the Langmuir isotherm model, with a maximum adsorption capacity of 492.6 mg/g, 492.6 mg/g, and 490.196 mg/g for Azorubine, Sunset Yellow, and Hexavalent Chromium, respectively. The kinetic studies showed that the pseudo-second-order model provided a better correlation between experimental data. Furthermore, the calculated thermodynamic parameters confirmed that the adsorption of Cr(VI), E110, and E122 by CS@CTAB material is a spontaneous and exothermic process. The fabricated CS@CTAB adsorbent was employed for the efficient elimination of Azorubine, Sunset Yellow, and hexavalent chromium from real water samples, synthetic mixtures, and colored soft drinks, with a percentage of recovery of ~ 96%. The plausible adsorption mechanisms of Azorubine, Sunset Yellow, and hexavalent chromium on the surface of CS@CTAB are elucidated. The adsorption anticipated to be due to electrostatic interaction and hydrogen bond formation for hexavalent chromium; while the adsorption of Azorubine and Sunset Yellow, was assumed to be due to electrostatic interaction, hydrogen bonding, and n-π interaction. Finally, the study demonstrates the efficiency of CS@CTAB for the removal of anionic species from several samples, including natural water and colored beverages.

Immobilization of Microcystin by the Hydrogel-Biochar Composite to Enhance Biodegradation during Drinking Water Treatment

Microcystin-LR (MC-LR), the most common algal toxin in freshwater, poses an escalating threat to safe drinking water. This study aims to develop an engineered biofiltration system for water treatment, employing a composite of poly(diallyldimethylammonium chloride)-biochar (PDDA-BC) as a filtration medium. The objective is to capture MC-LR selectively and quickly from water, enabling subsequent biodegradation of toxin by bacteria embedded on the composite. The results showed that PDDA-BC exhibited a high selectivity in adsorbing MC-LR, even in the presence of competing natural organic matter and anions. The adsorption kinetics of MC-LR was faster, and capacity was greater compared to traditional adsorbents, achieving a capture rate of 98% for MC-LR (200 μg/L) within minutes to tens of minutes. Notably, the efficient adsorption of MC-LR was also observed in natural lake waters, underscoring the substantial potential of PDDA-BC for immobilizing MC-LR during biofiltration. Density functional theory calculations revealed that the synergetic effects of electrostatic interaction and π-π stacking predominantly contribute to the adsorption selectivity of MC-LR. Furthermore, experimental results validated that the combination of PDDA-BC with MC-degrading bacteria offered a promising and effective approach to achieve a sustainable removal of MC-LR through an "adsorption-biodegradation" process.

Correlation between cocoa shell modifications by CTAB and its dye adsorption properties

Cocoa shell was modified whit sodium hydroxide (NaOH) and cationic surfactant cetyltrimethylammonium bromide (CTAB) to increase surface functionality, surface area, and positive charge density. The prepared adsorbent CC-OH-CTAB was used to remove indigo carmine (IC) and bromocresol green (BCG) dyes from water. The optimal pH for IC and BCG adsorption were 2 and 4, respectively. The equilibrium was attained after a contact time of 30 min for IC and 120 min for BCG. The maximum adsorption capacity (Qmax) of IC and BCG obtained was 85.1 mg g-1 and 192.7 mg g-1, respectively. The Liu isotherm model best described the equilibrium results. The adsorption kinetics model showed that IC and BCG adsorption onto CC-OH-CTAB followed the pseudo-first-order and pseudo-second-order model, respectively. The regeneration and reusability experiments indicated that CC-OH-CTAB had much stability and excellent performance meanwhile repeatedly used. Finally, the insertion of CTAB on the CC-OH surface proved to be an excellent way to improve the adsorption performance of this material concerning dyes.

Selective adsorption of anionic and cationic dyes on mesoporous UiO-66 synthesized using a template-free sonochemistry method: kinetic, isotherm and thermodynamic studies

In this study, template-free mesoporous UiO-66(U) has been successfully synthesized in shortened time by sonochemical methods and provided energy savings. The synthesized mesoporous UiO-66(U) demonstrated irregular morphology particle around 43.5 nm according to the SEM image. The N2 adsorption-desorption isotherm indicated an irregular, 8.88 nm pore width mesoporous structure. Ultrasonic irradiation waves greatly altered mesoporous materials. A mechanism for mesoporous UiO-66(U) formation has been proposed based on the present findings. Sonochemical-solvent heat saves 97% more energy than solvothermal. Mesoporous UiO-66(U) outperformed solvothermal-synthesized UiO-66(S) in adsorption. These studies exhibited that mesopores in UiO-66 promote dye molecule mass transfer (MO, CR, and MB). According to kinetics and adsorption isotherms, the pseudo-second-order kinetic and Langmuir isotherm models matched experimental results. Thermodynamic studies demonstrated that dye adsorption is spontaneous and exothermically governed by entropy, not enthalpy. Mesoporous UiO-66(U) also showed good anionic dye selectivity in mixed dye adsorption. Mesoporous UiO-66(U) may be regenerated four times while maintaining strong adsorption capability.

Insights on applications of bentonite clays for the removal of dyes and heavy metals from wastewater: a review

In recent decades, increased industrial, agricultural, and domestic activities have resulted in the release of various pollutants into the aquatic systems, which require a reliable and environmentally friendly method to remove them. Adsorption is one of the most cost-effective and sustainable wastewater treatment techniques. A plethora of low-cost bio-based adsorbents have been developed worldwide so far to supplant activated carbon and its high processing costs. Bentonite clays (BCs), whether in natural or modified form, have gained enormous potential in wastewater treatment and have been used successfully as a novel and cost-effective bio-sorbent for removing organic and inorganic pollutants from the liquid suspension. It has become a sustainable solution for wastewater treatment due to its variety of surface and structural properties, superior chemical stability, high capacity for cation exchange, elevated surface area due to its layered structure, non-toxicity, abundance, low cost, and high adsorption capacity compared to other clays. This review encompasses comprehensive literature about various modification techniques and adsorption mechanisms of BCs concerning dyes and heavy metal removal from wastewater. A critical overview of different parameters for optimizing adsorption capacity and regeneration via the desorption technique has also been presented here. Finally, a conclusion has been drawn with some future research recommendations based on technological challenges encountered in industrializing these materials.

Preparation and adsorption performance of functionalization cellulose-based composite aerogel

Herein, functionalization cellulose-based composite aerogels with the addition of carboxyl cellulose nanofibers (CNF), montmorillonite (MMT) and polyethyleneimine (PEI) were fabricated by solution blending and freeze-drying technology. MMT was blended into the cellulose framework as a reinforcing agent. PEI combined with cellulose through amidation reaction, and the synergism of hydrogen bond and chemical bond helped the CNF/MMT/PEI composite aerogels (CMP) with good mechanical properties. The morphology, chemical structure and thermal stability of the CMP were characterized. The adsorption properties and mechanism of the CMP were discussed, using Congo red (CR) dye as an adsorbate. The results showed that the CMP formed a three-dimensional network structure with abundant pores. The addition of PEI regulated the surface charge distribution of cellulose and improved the adsorption performance of CMP for CR with the adsorption capacity of 3114 mg/g calculated by the Langmuir model. The adsorption process of CMP-30 for CR was more in line with the pseudo-second-order kinetic model and Langmuir isotherm model, indicating chemical adsorption of a single molecular layer. After functionalized by octadecyl trichlorosilane (OTS), the contact angle of the aerogel surface was 151.80°. Meanwhile, the CMP-30 was transformed from hydrophilic and lipophilic properties to hydrophobic and lipophilic properties.

CTAB-functionalized δ-FeOOH for the simultaneous removal of arsenate and phenylarsonic acid in phenylarsenic chemical warfare

This study prepared a cetyltrimethylammonium bromide (CTAB) functionalized δ-FeOOH using the coprecipitation method to remove arsenate and phenylarsonic acid in water polluted by phenylarsonic chemical warfare agents. Under neutral conditions, the adsorption capacity for arsenate and phenylarsonic acid was 45.7 and 85.3 mg g^-1, respectively. The adsorption process conformed to the pseudo-second-order kinetics and Freundlich isothermal adsorption model, and the adsorption was spontaneous and endothermic. The CTAB-functionalized δ-FeOOH could effectively resist the interference of coexisting anions except for CO₃^2-, SiO₃^2- and PO₄^3-. Furthermore, the adsorption mechanism was proposed by combining the adsorption experimental results, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and density functional theory analyses. The results showed that the adsorption of arsenate by the CTAB-functionalized δ-FeOOH was mainly through the formation of bidentate-dinuclear inner-sphere complexes and electrostatic interactions. While for phenylarsonic acid, the formation of monodentate-mononuclear inner-sphere complexes on (100) and (110) crystal facets, and the formation of bidentate-dinuclear inner-sphere complexes on the (002) crystal facet, as well as hydrogen bonding, electrostatic interaction, and π-hydrophobic interaction between organic compounds were the primary mechanism. Moreover, the CTAB-functionalized δ-FeOOH could maintain about 60% of the adsorption capacity for the two pollutants after five cycles. Overall, CTAB-functionalized δ-FeOOH has good potential for the remediation of inorganic and organic arsenic-contaminated water bodies.

Pharmaceuticals removal by synergistic adsorption and S-scheme photocatalysis using nano-CeO2-coupled Fe3O4 on a CTAB matrix and investigation of the nanocomposite's antibacterial and antibiofilm activities: intrinsic degradation mechanism

S-Scheme photocatalytic mechanism of a fabricated nano-heterojunction.

Three novel Co(II)-based MOFs: Syntheses, structural diversity, and adsorption properties

In this paper, three new cobalt-based metal organic frameworks (MOFs) with different topologies, namely {[Co(HL)(tib)(H2O)]·2H2O}n (1), [Co3(L)2(bibp)4(H2O)2]n (2) and [Co2(L)(bip)(μ3-OH)]n (3) (H3L = 3-(3,5-dicarboxylphenoxy)-6-carboxylpyridine, tib = 1,3,5-tirs(1-imidazolyl)benzene, bibp = 4,4'-bis(imidazolyl)biphenyl,...

Highly-efficient PVDF adsorptive membrane filtration based on chitosan@CNTs-COOH simultaneous removal of anionic and cationic dyes

An adsorptive membrane filtration based on polyvinylidene fluoride (PVDF) with chitosan (CS) and carboxylated carbon nanotubes (CNTs-COOH) is prepared by method of phase conversion, and the PVDF-CS@CNTs-COOH membranes can effectively separate anionic and cationic dye wastewater. Compared to pure PVDF membranes, PVDF-CS@CNTs-COOH increases pure water flux from 36.39 (L·m^-2·h^-1) to 85.25 (L·m^-2·h^-1), an increase of nearly 230%. The membrane exhibits excellent rejection performance in the filtration of six types of dye wastewater. The modified membranes also performed well in terms of rejection of mixed anionic and cationic dyes and also have a high performance in recycling, with a flux of over 94% for both anionic and cationic dyes. In addition, the adsorption curve fitting results showed that the adsorption process was more consistent with the pseudo-second-order adsorption kinetic model and Langmuir mode.

Melanized-Cationic Cellulose Nanofiber Foams for Bioinspired Removal of Cationic Dyes

In recent years, water pollution has developed into a severe environmental and public health problem due to rapid urbanization and industrialization, especially in some developing countries. Finding solutions to tackle water pollution is urgently required and is of global importance. Currently, a range of water treatment methods are available; however, a water remediation process that is simple, inexpensive, eco-friendly, and effective for the removal of pollutants down to ppm/ppb concentrations has long been sought after. Herein, we describe a novel approach using fungal melanin for developing melanized-cationic cellulose nanofiber (melanized-C-CNF) foams that can successfully remove pollutants in water systems. The foam can be recycled several times while retaining its adsorption/desorption property, indicating high practicability for adsorbing the cationic dye crystal violet. This work highlights the opportunity to combine both the advanced features of sustainable polymers such as cellulose and the unique properties of fungal melanin to manufacture biohybrid composites for water purification.

Evaluation of an Ionic Porous Organic Polymer for Water Remediation

The targeted synthesis of a novel ionic porous organic polymer (iPOP) was reported. The compound (denoted as QUST-iPOP-1) was built up through a quaternization reaction of tris(4-imidazolylphenyl)amine and cyanuric chloride, and then benzyl bromide was added to complete the quaternization of the total imidazolyl units. It featured a special exchangeable Cl^-/Br^--rich structure with high permanent porosity and wide pore size distribution, enabling it to rapidly and effectively remove environmentally toxic oxo-anions including Cr₂O₇^2-, MnO₄^-, and ReO₄^- and anionic organic dyes with different sizes including methyl blue, Congo red, and methyl orange from water. Notably, QUST-iPOP-1 showed ultra-high capacity values for radioactive TcO₄^- surrogate anions (MnO₄^- and ReO₄^-), Cr₂O₇^2-, methyl blue, and Congo red, and these were comparable to some reported compounds of exhaustive research. Furthermore, the relative removal rate was high even when other concurrent anions existed.

Controlled surface functionalization of Ni-S nanostructures for pH-responsive selective and superior pollutants adsorption

Herein, we developed a synthetic strategy to functionalize Ni-S nanostructures (NS) using a facile precipitation method at moderate temperature. The surface functionality of NS is controlled by varying amount of mixed surfactants to achieve the pH-responsive selective adsorption of anionic and cationic dyes and the adsorption of ciprofloxacin (CIP) and tetracycline (TC) antibiotics. Powder XRD diffraction pattern revealed the phase of NS was changed from α-NiS to mixed phases after functionalization. The surface area of functionalized NS was significantly enhanced by ~5 times of that unfunctionalized NS as 6.6 m²g^-1 to 30.3 m²g^-1. The NS selectively adsorbed methyl orange (MO) at pH 4.5 and methylene blue (MB) at pH 11.5 with separation efficiency values of 94.2% and 97.9% respectively. The maximum adsorption capacity for MO, MB, TC and CIP are obtained as 1526.3, 1031.2, 1540.8 and 632.4 mg g^-1, respectively. The electrostatic interaction is predominantly involved in the adsorption of dyes whereas adsorption of antibiotics changed to hydrogen bonding and metal coordination. Thermodynamics parameters indicated exothermic and spontaneous adsorption of dyes. The optimized adsorbent is easily recyclable. Thus, the developed strategy of functionalization of nanostructures unveils a practical approach towards selective and efficient adsorption of organic pollutants.

Rational Fabrication of Multiple Dimensional Assemblies from Tryptophan-Based Racemate

Fabricating structural complex assemblies from simple amino acid-based derivatives is attracting great research interests due to their easy accessibility and preparation. However, the morphological regulation of racemates (an equimolar mixture of enantiomers) were largely overlooked. In this work, through rational modulation of kinetic and thermodynamic parameters, we achieved multiple dimensional architectures employing tryptophan-based racemate (RPWM). Upon assembling, 1D bundled nanofibers, 2D lamellar nanostructure and 3D urchin-like microflowers could be obtained depending on the solvents used. The corresponding morphology evolutions were successfully illustrated by changing the enantiomeric excess (ee) value. Moreover, for RPWM, uniform 0D nanospheres were formed in H 2 O under 4 ℃, which could spontaneously convert into lamella under ambient temperature. Taking advantages of its temperature-responsive phase change behavior, RPWM assemblies exhibited excellent removal efficiency for organic dye RhB, and could be reused for several consecutive cycles without significant changes in its removal performance. Taken together, it's rational to envision that the engineering of racemates assembly pathways can greatly increase the robustness in a wide variety of supramolecular materials and further lead to their blooming versatile applications.

Efficient adsorption removal of anionic dyes by an imidazolium-based mesoporous poly(ionic liquid) including the continuous column adsorption-desorption process

The mesoporous poly(N,N'-methylene-bis(1-(3-vinylimidazolium)) chloride), labeled as PDVIm-Cl, with double anions (Cl^-) and low monomer molecular weight was synthesized and applied in the adsorption of anionic dyes (acid orange 7 (AO7), sunset yellow (SY), reactive blue 19 (RB19), congo red (CR)). Due to the mesoporous structure, abundant Cl^- and positively charged imidazole rings, the poly(ionic liquid) (PIL) exhibited superior adsorption ability towards anionic dyes. What is more, the RB19 adsorption by PDVIm-Cl could achieve the highest capacity (2605 ± 254 mg g^-1) which was nearly twice higher than the maximum adsorption capacity of the previously reported materials. All the adsorption kinetic data and isotherms fitted well with the pseudo second-order model and Langmuir-Freundlich model. To better explore the practical potential of the PIL for dye adsorption, the adsorption under different pH values and column adsorption performances were also evaluated. Results showed that PDVIm-Cl exhibited high removal efficiencies for anionic dyes over a wide pH range (2-10). Also, the great reusability could be well demonstrated by the achievable continuous column adsorption-desorption process. It is worth mentioning that the regeneration could be realized with very little desorbent which was far less than the adsorption volume flowing through the column and the desorption efficiency was well maintained after three consecutive cycles. At last, the adsorption mechanism was explored by experiments combined with quantum chemical calculations and showed anionic dyes adsorption by PDVIm-Cl was a joint process dominated by the ion exchange, electrostatic interaction, hydrogen bond and π-π stacking.

Chitosan-based hybrid materials for adsorptive removal of dyes and underlying interaction mechanisms

Environmental pollution by dyes molecules has become a subject of intensive research in recent years due to their hazardous effects on human health, organisms, and animals. Effective treatment and removal of dye molecules from the environmental matrices and water sources are of supreme concern. The deployment of cheap, safe, green, sustainable, and eco-friendly materials to remove these pollutants from water is the main challenge during the last decades. Chitosan and its derivatives/composites, as a cheap, easily available, and environmentally friendly sorbent, have attracted increasing attention for the removal of dye molecules. This review article focuses on the application of chitosan and chitosan-based smart adsorbents for the removal of dyes. Recent methods for the preparation of chitosan-based composites and their application in the removal of dyes are discussed. Moreover, the possible mechanisms for the interaction of chitosan and chitosan-based adsorbents with dyes molecules were evaluated. Finally, future prospects of using chitosan as an adsorbent for the removal of dye molecules are directed.

Facile synthesis of the crescent-like SnS nanocrystals capped by polyvinyl pyrrolidone and its performance of adsorbing dyes

With using Sn²⁺ as tin source, l-cysteine as sulphur source and polyvinyl pyrrolidone (PVP, M_w = 1300000) as surfactant, a novel three-dimensional and crescent-like SnS nanocrystal (NCs) was successfully synthesized in a one-pot hydrothermal method. The as-prepared SnS NCs displayed uniform crescent-like morphological structure, and demonstrated excellent efficiency for the adsorption of cationic dyes such as rhodamine B (RhB) and methylene blue (MB). Kinetic analysis indicated that the adsorption process followed the pseudo second-order model, and the maximum capacity of the SnS NCs to adsorb MB was determined by Langmuir equation to be 252 mg⋅g^-1 at 298 K. The pH dependence of SnS NCs on the adsorption of cationic dyes and the characterization of zeta potential jointly suggested the existence of electrostatic attraction in the process. Overall, this study showed that electrostatic field of functional groups and the capping of PVP could significantly enhance the adsorption performance of the SnS NCs, and also provides a novel insight into the development of highly efficient inorganic adsorbents for cationic dyes.

3D Metallo-organic coordination assembly-based anion-enriched supramolecular material for fast and efficient removal of Cr2O72

Chromium(VI), especially dichromate (Cr₂O₇^2-) contamination in wastewater due to rapid industrialization with uncontrolled effluent management is still a serious concern which needs focused attention. Multiprong approaches are practiced such as chemical precipitation, reverse osmosis, ion-exchange, adsorption by granular activated carbon etc. to capture and separate this "Group A" human carcinogenic effluent from water. However, low capture capacity, non-reusability, poor selectivity, pH-limited performance are some major limitations of these techniques. Recently, metal organic frameworks (MOFs), metal organic cages (MOCs), porous organic polymers (POPs) or covalent organic frameworks (COFs), covalent organic networks (CONs) etc. emerged as new-generation materials to overcome such limitations. However, the development is still in initial stage and issues related to structural stability and integrity of many MOFs in water and in wide pH range, as well as reusability need to be addressed. At this juncture, herein we report a novel [Zn(terpyridine)₂]²⁺-templated trisimidazolium-based highly cationic three-dimensional metal-organic coordination assembly (3D MOCA), serving as a new class of efficient, fast, robust and recyclable dichromate-removal material. Not only the highly cationic assembly is enriched with a high density of Br^- anions, but its three-dimensional propagation and flexibility also exposes the exchangeable Br^- ions for facile anion-metathesis with Cr₂O₇^2-. By virtue of the benefits of these attributes, the presented supramolecular material exhibits a high capture capacity (469 mg g^-1), fast exchange kinetics (0.028 g mg^-1 min^-1), wide working pH range (pH 2-12) and reusability up to a minimum of 10 cycles without much loss of efficiency. Key mechanistic examinations highlight the evidences in favor of ion-exchange-based chemistry to be responsible for dichromate removal with the present material.

Facile and Scalable Fabrication of Antibacterial CO2-Responsive Cotton for Ultrafast and Controllable Removal of Anionic Dyes

A novel CO₂-responsive cotton as an eco-friendly adsorbent derived from poly(4-acryloyloxybenzophenone-co-2-(dimethylamino) ethyl methacrylate) and cotton was fabricated via a facile and fast dip-coating method. As expected, upon CO₂ stimulation, the protonated cotton presented CO₂-induced "on-off" selective adsorption behaviors toward anionic dyes owing to electrostatic interactions. The adsorption isotherms and kinetics of the CO₂-responsive cotton toward anionic dyes obeyed the Langmuir isotherm and pseudo-second-order kinetics models, respectively. It is noteworthy that the CO₂-responsive cotton exhibited high adsorption capacity and ultrafast adsorption rate toward anionic dyes with the maximum adsorption capacities of 1785.71 mg g^-1 for methyl orange (MO), 1108.65 mg g^-1 for methyl blue (MB), and 1315.79 mg g^-1 for naphthol green B (NGB), following the adsorption equilibrium times of 5 min for MO, 3 min for MB, and 4 min for NGB. Moreover, the CO₂-responsive cotton also exhibited high removal efficiency toward anionic dyes in synthetic dye effluent. Additionally, the CO₂-responsive cotton could be facilely regenerated via heat treatment under mild conditions and presented stable adsorption properties even after 15 cycles. Finally, the as-prepared CO₂-responsive cotton exhibited outstanding antibacterial activity against E. coli and S. aureus. In summary, this novel CO₂-responsive cotton can be viewed as a promising eco-friendly adsorbent material for potential scalable application in dye-contaminated wastewater remediation.

Investigation of magnetic silica nanocomposite immobilized Pseudomonas fluorescens as a biosorbent for the effective sequestration of Rhodamine B from aqueous systems

In the current research work, a novel eco-friendly Fe₃O₄@SiO₂ nanocomposite immobilized with Pseudomonas fluorescens biomass in calcium alginate beads (MSAB) was used as biosorbent for the elimination of hazardous Rhodamine B dye from aqueous system. The FTIR, XRD and SEM results showed that the MSAB possessed excellent surface properties for the effective sequestration of Rhodamine B. The batch adsorption results concluded that the adsorption of Rhodamine B using MSAB is highly influenced by the parameters such as pH, adsorbent dosage, initial dye concentration and contact time. The equilibrium and kinetics data get best fitted in the Freundlich isotherm and Pseudo first order kinetics for the studied adsorption system. The Langmuir monolayer adsorption capacity was found to be 229.6 mg/g. The thermodynamic studies showed that the adsorption was spontaneous, feasible and exothermic in nature. The adsorption mechanisms are understood using the Intraparticle diffusion and Boyd model. Thus, this Magnetic silica alginate beads (MSAB) containing dead biomass of Pseudomonas fluorescens is considered to be an ideal biosorbent which can be used as an effective tool in treating the industrial dye wastewater treatment.

A PW12/Ag functionalized mesoporous silica-coated magnetic Fe3O4 core-shell composite as an efficient and recyclable photocatalyst

The novel composite, Fe₃O₄@SiO₂@mSiO₂-PW₁₂/Ag, was successfully prepared by in situ loading Ag nanoparticles (Ag NPs) on the surface of grafted phosphotungstate (denoted as PW₁₂) Fe₃O₄@SiO₂@mSiO₂via a photoreduction deposition method. PW₁₂ not only acts as a reducing agent and stabilizer for Ag NPs but also as a bridge to link Ag NPs and the SiO₂ shell in the loading process. Its activity toward the photodegradation of methyl orange (MO) and photoreduction of Cr₂O₇^2- anions was evaluated. Experimental results showed that Fe₃O₄@SiO₂@mSiO₂-PW₁₂/Ag with 5.3 wt% Ag loading and 18.65 wt% of PW₁₂ exhibits the highest photocatalytic efficacy, and complete degradation of MO and 91.2% photoreduction of Cr(vi) were realized under simulated sunlight for 75 min, respectively. The enhanced catalytic activities of the composite are due to its high specific surface area, the synergistic effect among the components and the formation of a heterojunction of PW₁₂/Ag. The possible enhanced photocatalytic mechanism is proposed. The catalyst is durable and can be easily recovered using a magnet for recycling without a significant loss of catalytic activity.

In-situ carbonization of ZIF-67 to fabricate magnetically Co/N-mC with high adsorption capacity toward water remediation

Co and N co-modified mesoporous carbon composites (Co/N-mC) have been simply prepared at low cost from the carbonization of ZIF-67 wherein not only providing surface N-modification for promoting the adsorption behavior of acidic dyes, but also constructing a magnetic property for convenient separation. Co/N-mC composite presented the adsorption ability of MO (178 mg g−1) > RhB (141 mg g−1) (T = 25 °C, pH = 7.0, C0 = 20 mg L−1) because of its spacious porous structure (BET: 250.8 m2 g−1; pore size: 3.9 nm) and functional basic character (pyrrolic-N and pyridinic-N). Compared with basic dyes (RhB), mesoporous C doped with N improves the adsorption of acid dyes (MO). In addition, the magnetic properties introduced in the Co/N-mC make it easier to separate after adsorption and regeneration by an external magnetic field.

A series of novel Co(ii)-based MOFs: syntheses, structural diversity, and various properties

Three novel Co(ii)-based MOFs, having structural diversities and various properties are successfully synthesized.

Novel Fe3O4-poly(methacryloxyethyltrimethyl ammonium chloride) adsorbent for the ultrafast and efficient removal of anionic dyes

The removal of anionic dyes from wastewater has attracted global concern. In this work, a novel Fe3O4-poly(methacryloxyethyltrimethyl ammonium chloride) (Fe3O4-pDMC) adsorbent for the efficient removal of anionic dyes from wastewater was successfully synthesized by grafting methacryloxyethyltrimethyl ammonium chloride (DMC) on the surfaces of Fe3O4. Various characterization analyses confirmed that the obtained Fe3O4-pDMC possessed numerous functional groups on its surfaces and retained good magnetic separation properties. Fe3O4-pDMC showed ultrafast removal for acid orange 7 (AO7, 58.6%, 1 min) and direct blue 15 (DB15, 98.1%, 1 min), and the maximum adsorption capacity was high (266.8 and 336.5 mg g-1 for AO7 and DB15, respectively). In addition, the adsorption process was in accordance with pseudo-second-order kinetics and the Langmuir isotherm. The mechanism underlying the adsorption of Fe3O4-pDMC on anionic dyes was mainly dependent on electrostatic interaction. This study illustrated that Fe3O4-pDMC has great potential applications as an environmentally friendly, desirable adsorbent for the efficient removal of anionic dyes from wastewater.

Cyclodextrin derivatives used for the separation of boron and the removal of organic pollutants

Adsorption plays an important role in seawater desalination, wastewater treatment, and, especially, boron removal from natural aqueous systems. In this paper, two sponge-like multifunctional polymers based on a cyclodextrin backbone were synthesized and used as adsorbents for the removal of boron, methylene blue (MB), methyl orange (MO), and phenol. The syntheses were carried out by esterification, atom transfer polymerization, and nucleophilic addition reaction. The polymers were characterized by ¹H NMR spectroscopy, IR spectroscopy, XRD, XPS, and SEM. The performance of the two different adsorbents was investigated considering the effect of pH, initial concentration, and the anions and cations in an aqueous solution of borates. The experimental data were fitted with an adsorption isothermal model, adsorption kinetic model and other models. Both adsorbents exhibited high adsorption capacities (B: 31.05 mg/g and 20.45 mg/g, MB: 29.43 mg/g and 32.29 mg/g, MO: 47.36 mg/g and 49.23 mg/g, phenol: 5.04 mg/g and 4.35 mg/g, respectively) and a fast adsorption rate. The boron adsorption was found to be an exothermic process. The adsorbents show promising potential for the removal of boron and benzene-containing organic pollutants from aqueous solution.

Cetyl trimethyl ammonium bromide modified magnetic biochar from pine nut shells for efficient removal of acid chrome blue K

Biochar was prepared by rapid pyrolysis using pine nut shell as raw materials. Then cetyl trimethyl ammonium bromide modified magnetic biochar material (CTAB-MC) was obtained after modifying biochar by FeCl₃ and cetyl trimethyl ammonium bromide. The CTAB-MC was characterized by SEM, FTIR, XRD and Magnetic analyses. Adsorptive property of the CTAB-MC for acid chrome blue K (AK) was studied. It was found that adsorption capacity was affected by solution pH, temperature, adsorption time, initial concentration and ionic strength. The CTAB-MC showed higher adsorption ability toward acid chrome blue K, which was up to 40% higher than that of MC. The experimental results showed that adsorption data of AK on the CTAB-MC well conformed to the Langmuir isotherm adsorption model and the pseudo-second order kinetic model. The CTAB-MC can be recycled three times. This work reveals that CTAB-MC is a promising adsorbent with broad application prospects.