Utilization of rice husk and waste aluminum cans for the synthesis of some nanosized zeolite, zeolite/zeolite, and geopolymer/zeolite products for the efficient removal of Co(II), Cu(II), and Zn(II) ions from aqueous media

Molten salt synthesis of MXene-derived hierarchical titanate for effective strontium removal

The removal and recovery of radioactive Sr(II) from wastewater and seawater has been of great concern due to the negative environmental impacts of nuclear energy development and the potential risk of nuclear accidents. Herein, a facile molten salt synthesis strategy was developed to systematically investigated the reaction of different types of MXenes with nitrates. Among the products, K+ intercalated hierarchical titanate nanostructures (K-HTNs) obtained from the direct chemical transformation of multilayered Ti3C2Tx exhibited unique layered structures, good physicochemical properties, and outstanding adsorption performance for Sr(II). The maximum adsorption capacity of Sr(II) by K-HTNs reached 204 mg·g-1 at ambient temperature, and the good regeneration and reusability of the titanate was also demonstrated. K-HTNs showed preferential selectivity for Sr(II) in different environmental media containing competing ions, and the removal efficiency of Sr(II) in real seawater was as high as 93.3 %. The removal mechanism was elaborated to be the exchange of Sr2+ with K+/H+ in the interlayers of K-HTNs, and the adsorbed Sr(II) had a strong interaction with Ti-O- termination on the titanate surface. Benefiting from the merits of rapid and scalable synthesis and excellent adsorption performance, MXene-derived K-HTNs have broad application prospects for the purification of 90Sr-contaminated wastewater and seawater.

Application of apophyllite and thomsonite natural zeolite as modified adsorbents for the removal of zinc from acid mine drainage

Materials composed of natural zeolite have the potential to serve as highly effective adsorbents in the treatment of wastewater. The present study explores zeolite resin-based Apophyllite and Thomsonite as adsorbents for removing Zinc from acid mine drainage solution. The characteristics of the natural zeolites (Apophyllites and Thomsonite) are investigated using X-ray diffraction, Fourier-transform infrared spectroscopy and Field emission scanning electron microscopy analysis. The removal of Zinc from AMD is explored, and the influence of metal ion concentration, resin dose, and pH is investigated using a batch exchange resin-based experimental method. Maximum zinc removal occurs in the pH range of 2-6 with an initial zinc content of 50-250 mg/L and a resin dosage of 25-700 mg/L, indicating that the adsorption process is pH-dependent. Various isotherm models, including those proposed by Freundlich and Langmuir as well as Redlich-Peterson, Dubinin, and Temkin, are used to verify the results of the experimental research. All these isotherm models' constants are determined. Both resins showed different sorption efficiencies at different operating conditions. However, highest Zn removal efficiency of 86.2% was observed for the Thomsonite zeolite resin whereas Apophyllite zeolite resin showed maximum Zn uptake of 81.6%. Thus, Thomsonite was found to be an effective sorbent.

Preparation and Density Functional Theory Studies of Aluminosilicate-Based Ceramic Solidified Products for Sr Immobilization

Strontium is a common radionuclide in radioactive waste, and its release into the environment can cause enormous damage to the ecosystem environment. In this study, the natural mineral allophane was selected as the substrate to prepare solidified ceramic products by cold pressing/sintering to solve the problem of the final disposal of radioactive strontium. Ceramic solidified products with various crystal structures were successfully prepared, and the microscopic morphology and energy-dispersive spectroscopy images of the samples showed a uniform distribution of Sr in the solidified products. Sr2Al2SiO7 and SrAl2Si2O8, which can stably solidify strontium, were formed in the solidified products, and the structural characteristics and stability of the above-mentioned substances were analyzed from the perspective of quantum chemical calculations using density functional theory. The calculation results showed that the overall deformation resistance of Sr2Al2SiO7 was higher than that of SrAl2Si2O8. Considering the isomorphic substitution effect of CaO impurities, we inferred that a mixed-crystalline structure of Ca2-xSrxAl2SiO7 may be present in the solidified products.

Significant photocatalytic decomposition of malachite green dye in aqueous solutions utilizing facilely synthesized barium titanate nanoparticles

The release of malachite green dye into water sources has detrimental effects on the liver, kidneys, and respiratory system. Additionally, this dye can impede photosynthesis and disrupt the growth and development of plants. As a result, in this study, barium titanate nanoparticles (BaTiO₃) were facilely synthesized using the Pechini sol-gel method at 600 °C (abbreviated as EA600) and 800 °C (abbreviated as EA800) for the efficient removal of malachite green dye from aqueous media. The Pechini sol-gel method plays a crucial role in the production of barium titanate nanoparticles due to its simplicity and ability to precisely control the crystallite size. The synthesized barium titanate nanoparticles were characterized by several instruments, such as X-ray diffraction (XRD), high-resolution transmission electron microscopy (HR-TEM), Fourier transform infrared spectroscopy, and a diffuse reflectance spectrophotometer. The XRD analysis confirmed that the mean crystallite size of the EA600 and EA800 samples is 14.83 and 22.27 nm, respectively. Furthermore, the HR-TEM images confirmed that the EA600 and EA800 samples exhibit irregular and polyhedral structures, with mean diameters of 45.19 and 72.83 nm, respectively. Additionally, the synthesized barium titanate nanoparticles were utilized as catalysts for the effective photocatalytic decomposition of malachite green dye in aqueous media. About 99.27 and 93.94% of 100 mL of 25 mg/L malachite green dye solution were decomposed using 0.05 g of the EA600 and EA800 nanoparticles within 80 min, respectively. The effectiveness of synthesized BaTiO₃ nanoparticles as catalysts stems from their unique characteristics, including small crystallite sizes, a low rate of hole/electron recombination owing to ferroelectric properties, high chemical stability, and the ability to be regenerated and reused multiple times without any loss in efficiency.

In-situ conversion of geopolymer into novel floral magnetic sodalite microspheres for efficient removal of Cd(II) from water

In the present work, a novel, floral-like, magnetic sodalite microsphere (SODM) was synthesized in situ by using fly ash (FA) and metakaolin (MK) as raw materials and was used to remove Cd(II) from water. Its magnetism can solve the problems of adsorbent recovery and possible secondary pollution. During the static adsorption, SODM shows a maximum adsorption capacity of 245.17 mg/g. The adsorption of Cd(II) on the SODM surface is spontaneous, exothermic, and physicochemical adsorption, which was evaluated by thermodynamics, kinetics, and isotherm studies. During dynamic adsorption, SODM shows a maximum adsorption capacity of 342.74 mg/g in the simulated solution prepared by the deionized water, compared to 215.88 mg/g in the simulated solution prepared using Xiangsi Lake water from Guangxi Minzu University. At 0.5 g SODM dosage in the dynamic adsorption, the adsorption capacity could rise to 632.81 mg/g. These results demonstrated the excellent Cd (II) adsorption performance of the SODM. The adsorption of cadmium on the SODM surface includes the synergistic effects of electrostatic attraction, ion exchange, and surface coordination reaction. Besides, the SODM shows good regeneration performance in both the deionized water and Xiangsi Lake water. The present study explores SODM as an adsorbent for the Cd (II) removal from wastewater and unbolts the industrial applicability of the SODM in the field of wastewater purification.

Faujasite-Type Zeolite Obtained from Ecuadorian Clay as a Support of ZnTiO3/TiO2 NPs for Cyanide Removal in Aqueous Solutions

In this study, zeolites prepared by the hydrothermal method from Ecuadorian clay were combined with the precursor clay and with the semiconductor ZnTiO₃/TiO₂ prepared by the sol-gel method to adsorb and photodegrade cyanide species from aqueous solutions. These compounds were characterized by X-ray powder diffraction, X-ray fluorescence, scanning electron microscopy, energy-dispersive X-rays, point of zero charge, and specific surface area. The adsorption characteristics of the compounds were measured using batch adsorption experiments as a function of pH, initial concentration, temperature, and contact time. The Langmuir isotherm model and the pseudo-second-order model fit the adsorption process better. The equilibrium state in the reaction systems at pH = 7 was reached around 130 and 60 min in the adsorption and photodegradation experiments, respectively. The maximum cyanide adsorption value (73.37 mg g^-1) was obtained with the ZC compound (zeolite + clay), and the maximum cyanide photodegradation capacity (90.7%) under UV light was obtained with the TC compound (ZnTiO₃/TiO₂ + clay). Finally, the reuse of the compounds in five consecutive treatment cycles was determined. The results reflect that the compounds synthesized and adapted to the extruded form could potentially be used for the removal of cyanide from wastewater.

Functionalization of Silica Nanoparticles by 5-Chloro-8-quinolinol as a New Nanocomposite for the Efficient Removal and Preconcentration of Al3+ Ions from Water Samples

In this work, silica nanoparticles were modified by 5-chloro-8-quinolinol as a new nanocomposite for the efficient elimination and preconcentration of Al³⁺ ions from several water sources. The fabricated composite was characterized utilizing XRD, SEM, FT-IR, TEM, CHN elemental analyzer, and N₂ adsorption/desorption analyzer. The XRD demonstrated the existence of a wide peak at 2θ = 30°. Also, all the peaks of silica were severely reduced, which confirms the success of loading the 5-chloro-8-quinolinol on the surface of the silica. The SEM and TEM images demonstrated that the composite resembled cotton, and this confirms that 5-chloro-8-quinolinol was successfully loaded on the silica surface. The specific surface area, the average pore size, and the total pore volume of the synthesized composite are 80.53 m²/g, 3.26 nm, and 0.185 cc/g, respectively. In addition, the greatest uptake capacity of the synthesized composite toward aluminum ions is 95.06 mg/g. The results indicated that the adsorption of aluminum ions onto the silica/5-chloro-8-quinolinol composite follows the Langmuir isotherm and pseudo-second-order model. Moreover, the adsorption of aluminum ions by the silica/5-chloro-8-quinolinol composite is spontaneous, chemical, and thermodynamically favorable. The values of % recovery were more than 97%, whereas the values of % RSD were less than 3.5%. Hence, this confirms the effectiveness of the proposed method in the determination of aluminum ions in real water samples.

The Effect of Sorbent Composition on Sorption Properties of Materials Based on Ti-Ca-Mg Phosphates

Individual titanium and calcium-magnesium phosphates are widely known as effective sorbents. The sorption processes on these phosphates are based on different mechanisms. The sorption efficiency towards different cations depends on the phase composition of the sorbent. Composite materials with various ratio Ti:(Ca+Mg) have been synthesized. The sorption properties of samples obtained towards Cs⁺, Sr²⁺, Co²⁺, Cd²⁺, Zn²⁺, Cu²⁺, and Pb²⁺ have been studied to establish the effect of sorbent composition on metal removal. The adsorption isotherms have been analyzed using the Langmuir, Freundlich, and Redlich-Peterson models. The composition of sorbents has no effect on the level of removal of readily hydrolyzable Pb²⁺ and Cu²⁺ cations. Removal of lead occurs preferentially via the precipitation of metal phosphates and hydroxides. Copper precipitates as hydroxide in case of a high share of Ca-Mg phosphates in the composite sorbent. The removal of cesium proceeds according to the ion exchange mechanism only. For Cd²⁺, Co²⁺, Sr²⁺, and Zn²⁺ cations, the sorption efficiency on the composite materials synthesized is found to increase with the increase in titanium phosphate's share in the sample. All composite sorbents synthesized demonstrated a considerable increase in the level of purification of solutions studied compared with individual Ti and Ca-Mg phosphates due to the synergism of the components.

Facile synthesis and characterization of Fe3O4/analcime nanocomposite for the efficient removal of Cu(II) and Cd(II) ions from aqueous media

In the water purification field, heavy metal pollution is a problem that causes severe risk aversion. This study aimed to examine the disposal of cadmium and copper ions from aqueous solutions by a novel Fe3O4/analcime nanocomposite. A field emission scanning electron microscope (FE-SEM), Fourier transform infrared spectroscopy (FT-IR), and X-ray diffraction were used to characterize the synthesized products. The FE-SEM images showed that the analcime and Fe3O4 samples consist of polyhedral and quasi-spherical shapes with average diameters of 923.28 and 28.57 nm, respectively. Besides, the Fe3O4/analcime nanocomposite consists of polyhedral and quasi-spherical shapes with average diameters of 1100.00 nm. The greatest uptake capability of the Fe3O4/analcime nanocomposite toward the copper and cadmium ions is 176.68 and 203.67 mg/g, respectively. The pseudo-second-order kinetic model and Langmuir equilibrium isotherm best describe the uptake of copper and cadmium ions using the Fe3O4/analcime nanocomposite. The uptake of copper and cadmium ions using the Fe3O4/analcime nanocomposite is exothermic and chemical in nature.

Assessment of surface and electrical properties of the TiO2@zeolite hybrid materials

Degradation of pollutants in aqueous medium is of high interest due to the impact on environment and human health, therefore, design and study of the physico-chemical properties of photocatalysts for water remediation are of major significance. Among properties of photocatalyst, those related to the surface and electrical mechanism are crucial to the photocatalyst´s performance. Here we report the chemical and morphological characteristics of TiO₂@zeolite photocatalyst by X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) respectively, and a coherent electrical conduction mechanism was proposed based on data obtained from assisted laser impedance spectroscopy (ALIS), in which the zeolite was synthesized from recycled coal fly ash. The results obtained by SEM and XPS verified the presence of spherical particles of TiO₂ anatase with presence of Ti³⁺ state. ALIS results showed that impedance of the entire system increases when the amount of TiO₂ increases and the samples with lower capacitive performance allowed a larger transfer of the charges between the solid-liquid interface. All results showed that higher photocatalytic performance of TiO₂ growth over hydroxysodalite with 8.7 wt% and 25 wt% of TiO₂ can be explained in terms of the morphology of TiO₂ and the interactions between substrate-TiO₂ mainly.

Geopolymer composite spheres derived from graphene-modified fly ash/slag: Facile synthesis and removal of lead ions in wastewater

Geopolymer composite spheres derived from potassium-activated graphene-modified slag/fly ash powder were produced in a polyethylene glycol (PEG 400) solvent. The effect of graphene type (graphene oxide (GO) and few-layered graphene (GNP)) on the pore structure and lead ions (Pb²⁺) removal performance of the spheres were evaluated. The results showed that the composite spheres modified with GOs (0.1-0.4 wt%) and GNPs (1-4 wt%) could be spheroidized with an improved performance to adsorb Pb²⁺ in solution. The graphene-containing spheres reached a maximum BET surface area of 68.85 m²/g. Pseudo-second-order and Langmuir isotherm models could express the adsorption process, which was controlled by both monolayer adsorption and chemisorption. The obtained spheres also showed high adsorption capacities for Ni²⁺, Cu²⁺, Zn²⁺ and Cd²⁺ ions. Chemical, physical, electrostatic, ion exchange and cation-π interaction were attributed to the adsorption mechanism of the spheres. The spheres showed good cycling ability compared to those without graphene, which had potential application in heavy metal wastewater treatment.

Facile synthesis and characterization of magnesium and manganese mixed oxides for the efficient removal of tartrazine dye from aqueous media

Nanomaterials are the most effective class of substances for use as adsorbents in wastewater treatment. Hence, the current study involves the facile and low-cost synthesis of MgMn₂O₄/Mn₂O₃ and MgMn₂O₄/Mn₂O₃/Mg₆MnO₈ as novel nanostructures from mixed solutions of Mg(ii) and Mn(ii) ions using the Pechini sol-gel method. After that, the remaining powder was calcined at 500, 700, and 900 °C for 3 h; the products were designated as G500, G700, and G900, respectively. The G500 sample consists of MgMn₂O₄ and Mn₂O₃, while the G700 and G900 samples consist of MgMn₂O₄, Mg₆MnO₈, and Mn₂O₃. The synthesized nanostructures were characterized using several tools, such as X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and N₂ adsorption/desorption analysis. The average crystallite size of the G500, G700, and G900 samples is 210.53, 95.27, and 83.43 nm, respectively. The SEM images showed that the G500 sample consists of square and rectangular bars with an average diameter of 3.18 μm. Also, the G700 and G900 samples consist of hexagonal, polyhedral, and irregular shapes with an average diameter of 1.12 and 0.54 μm, respectively. The synthesized nanostructures were further utilized as adsorbents for the efficient removal of tartrazine dye from aqueous media. The experimental data showed a good fit with the Langmuir isotherm and pseudo-first-order model. The maximum adsorption capacities of the G500, G700, and G900 adsorbents toward tartrazine dye are 328.95, 359.71, and 395.26 mg g^-1, respectively.

Functionalization of Sodium Magnesium Silicate Hydroxide/Sodium Magnesium Silicate Hydrate Nanostructures Using 2,3-Dihydroxybenzaldehyde as a Novel Nanocomposite for the Efficient Removal of Cd(II) and Cu(II) Ions from Aqueous Media

Cd(II) and Cu(II) ions cause many diseases in humans. Therefore, they should be removed from water sources using simple and cost-effective adsorbents. Consequently, sodium magnesium silicate hydroxide/sodium magnesium silicate hydrate nanostructures were synthesized and functionalized using 2,3-dihydroxybenzaldehyde as a novel nanocomposite. Several instruments were used to characterize the synthetic products, such as an X-ray diffractometer (XRD), a Fourier-transform infrared spectrophotometer (FT-IR), an N2 adsorption/desorption analyzer, a CHN elemental analyzer, an energy-dispersive X-ray spectrophotometer (EDS), and a field emission scanning electron microscope (FE-SEM). The functionalization of the nanostructures with 2,3-dihydroxybenzaldehyde led to the disappearance of the XRD peaks of the nanostructures and the presence of a broad XRD peak at 2θ = 32°. In addition, the FE-SEM images revealed that the nanostructures consisted of spheres, cubes, and irregular shapes with an average grain size of 115 nm, and the nanocomposite consisted of spherical conglomerates consisting of needle-like shapes. The anticipated morphology following the functionalization of the nanostructures with 2,3-dihydroxybenzaldehyde resulted from the presence of 2,3-dihydroxybenzaldehyde on the backbones of the nanostructures. The EDS results showed that the nanostructures were composed of O, Na, Mg, and Si with weight percentages equal to 38.59%, 5.95%, 16.60%, and 38.86%, respectively. Additionally, the nanocomposite was composed of C, N, O, Na, Mg, and Si with weight percentages equal to 55.31%, 2.23%, 30.09%, 6.56%, 2.98%, and 12.83%, respectively. The synthesized nanostructures and nanocomposite samples were utilized for the efficient removal of cadmium and copper ions from aqueous media using the ion exchange and chelation adsorption procedures, respectively. Optimum conditions for removing the cadmium and copper ions were achieved at a pH, time, and temperature equal to 7.5, 80 min, and 298 K, respectively. The maximum uptake capacities of the synthesized nanostructures and nanocomposite samples toward cadmium ions were 89.44 mg/g and 155.04 mg/g, respectively, and the maximum uptake capacities of the synthesized nanostructures and nanocomposite samples toward copper ions were 103.73 mg/g and 177.94 mg/g, respectively. Moreover, the adsorption processes were exothermic, chemical, and followed the pseudo-second-order model and Langmuir equilibrium isotherm model.

Fabrication of a waste cotton fabrics-based nanosystem for simultaneous removal of Cu(II) and Pb(II)

Herein, a waste cotton fabrics-based nanosystem was fabricated to simultaneously remove copper (Cu(II)) and lead ions (Pb(II)) from water and soil. Therein, carboxyl-functionalized zinc oxide microsphere (ZnO-COOH) with peanut shape was carried by cotton fabric (CF) to get CF/ZnO-COOH nanosystem. CF/ZnO-COOH with a good foldable property possessed a high removal capacity for Cu(II) and Pb(II) via electrostatic attraction and chelation. The result indicated that their removal efficiencies of CF/ZnO-COOH could reach over 95% after 2 h. The adsorption process was consistent with Langmuir (R² = 0.9905 of Cu(II) and R² = 0.9846 of Pb(II)) and pseudo-second-order kinetic models (R² = 0.9999 of Cu(II) and R² = 0.9999 of Pb(II)). The thermodynamic data showed that the adsorption process was spontaneous and exothermic. Additionally, CF/ZnO-COOH also possessed a high fixation ability for Cu(II) and Pb(II) in sand-soil column, especially for Pb(II) (15 cm, 0.4 μg kg^-1). Therefore, this wok provides an environmentally friendly and efficient way to remove Cu(II) and Pb(II) from water and soil concurrently.

Facile synthesis of waste-based CdS-loaded hierarchically porous geopolymer for adsorption-photocatalysis of organic contamination and its environmental risks

In order to obtain an adsorbent-photocatalyst with low-cost, strong stability and great reusability/recyclability, a waste-based and CdS-loaded hierarchically porous geopolymer (HPG) was prepared by facile synthesis. The adsorption-photocatalysis ability, reusability, and stability of HPG under different conditions were determined. Results indicated that HPG showed better adsorption-photocatalysis performance for organic dyes under alkaline environment, and it remained a high adsorption-photocatalysis efficiency after used for five times. Furthermore, HPG was stable in different environment conditions (strong acidic, acid raining, neutral, high salinity, and high alkali environment). The mass loss of HPG were around 3.22-6.68% (7 days extraction), and the immobilization rates of Cd²⁺ in neutral, high salinity, and high alkali environments were higher than 99.99%. Under visible light irradiation, HPG effectively photo-degraded the organic substances in overlying water of polluted sediments. After 330 min irradiation, the concentrations of COD and TOC were decreased from 47.52 mg/L and 20.9 mg/L to 16.58 mg/L and 11.19 mg/L, respectively. The humic-like and fulvic-like substances were transformed to protein-like substances under photo-degradation effect. This study confirmed that HPG possesses advantages in cost, chemical stability, and reusability, and it has a great potential to be used as in-situ remediation environmental functional material for organic contaminants in lake.

Boosting brackish water treatment via integration of mesoporous γ-Al2O3NPs with thin-film nanofiltration membranes

In this study, a simple method based on non-ionic surfactant polysorbates-80 was used to create mesoporous γ-Al₂O₃NPs. The properties of the prepared mesoporous alumina nanoparticles (Al₂O₃NPs) were verified using ATR-FTIR, XRD, SEM, TEM, DLS, and BET surface area analysis. Then, thin-film nanocomposite (TFN) nanofiltration membranes were fabricated by interfacial polymerization of embedded polyamide layers with varied contents (0.01 to 0.15 wt.%) of mesoporous γ-Al₂O₃NPs. The surface roughness, porosity, pore size, and contact angle parameters of all the prepared membranes were also determined. The performance of the fabricated membranes was investigated under various mesoporous γ-Al₂O₃NPs loads, time, and pressure conditions. Mesoporous γ-Al₂O₃NPs revealed an important role in raising both the membrane hydrophilicity and the surface negativity. The addition of 0.03 wt.% mesoporous γ-Al₂O₃NPs to the TFN membrane increased water flux threefold compared to the TF control (TFC) membrane, with maximum water flux reaching 96.5, 98, 60, and 52 L/(m².h) for MgSO₄, MgCl₂, Na₂SO₄, and NaCl influent solutions, respectively, with the highest salt rejection of 96.5%, 92.2%, 98.4%. The TFN-Al₂O₃ membrane was also able to soften water and remove polyvalent cations such as Mg²⁺ with a highly permeable flux. The TFN-Al₂O₃ membrane successfully removed the hardness of the applied water samples below the WHO limit compared to using merely the TFC membrane. Furthermore, the TFN-Al₂O₃ nanofiltration membrane unit proved to be a promising candidate for the desalination of real brine like that collected from the Safaga area, Egypt.

Facile Synthesis and Characterizations of Mixed Metal Oxide Nanoparticles for the Efficient Photocatalytic Degradation of Rhodamine B and Congo Red Dyes

Photocatalytic degradation has been suggested to be a cheap and efficient way to dispose of organic pollutants, such as dyes. Therefore, our research team strives to produce nanophotocatalysts in a simple and inexpensive way. In this work, the Pechini sol-gel technique was employed for the facile synthesis of Mn_0.5Zn_0.5Fe₂O₄/Fe₂O₃ and Fe_0.5Mn_0.5Co₂O₄/Fe₂O₃ as mixed metal oxide nanoparticles for the efficient photocatalytic degradation of Rhodamine B and Congo Red dyes. XRD, FT-IR, a N₂ adsorption/desorption analyzer, EDS, FE-SEM, and an UV-Vis diffuse reflectance spectrophotometer were used to characterize the produced samples. The XRD patterns revealed that the average crystallite size of the Fe_0.5Mn_0.5Co₂O₄/Fe₂O₃ and Mn_0.5Zn_0.5Fe₂O₄/Fe₂O₃ samples is 90.25 and 80.62 nm, respectively. The FE-SEM images revealed that the Fe_0.5Mn_0.5Co₂O₄/Fe₂O₃ sample consists of cubic and irregular shapes with an average diameter of 1.71 µm. Additionally, the Mn_0.5Zn_0.5Fe₂O₄/Fe₂O₃ sample consists of spherical shapes with an average diameter of 0.26 µm. The energy gaps of the Fe_0.5Mn_0.5Co₂O₄/Fe₂O₃ and Mn_0.5Zn_0.5Fe₂O₄/Fe₂O₃ samples are 3.50 and 4.3 eV and 3.52 and 4.20 eV, respectively. In the presence of hydrogen peroxide, the complete degradation of 100 mL of 20 mg/L of Rhodamine B and Congo Red dyes occurred at pH = 8 and 3, respectively, within 50 min, using 0.1 g of the synthesized samples.

Dual functional sites strategies toward enhanced heavy metal remediation: Interlayer expanded Mg-Al layered double hydroxide by intercalation with L-cysteine

The discharge of toxic heavy metals poses a serious threat to human health and environment. The existing water purification systems are lack of promising materials for rapid, efficient, and cost-efficient remediation of numerous toxic heavy metals. Herein, we report on the development of L-cysteine (Cys) intercalated Mg-Al layered double hydroxide (MgAl-LDH/Cys) with a loose lamellar porous architecture as an efficient and economically viable adsorbent for Pb(II) and Cd(II) removal. The intercalation with Cys creates dual functionality, i.e., the interlayer expansion accelerates the diffusion of heavy metals, while Cys acts as additional capture sites for heavy metals. Therefore, remarkable high maximum sorption capacities of 279.58 and 135.68 mg g^-1 for Pb(II) and Cd(II) were obtained for MgAl-LDH/Cys compared to those for pristine MgAl-LDH (30.15 and 36.77 mg g^-1). MgAl-LDH/Cys exhibits also much faster sorption kinetics in comparison with MgAl-LDH. Such enhancements are attributed to the intercalation of the chelating agent Cys in the MgAl-LDH interlayer channels. Moreover, it is proposed that the adsorption mechanisms involve the isomorphous replacement of Mg sites by Cd(II) forming CdAl-LDH, the precipitation of PbS and CdS, and the chelation of sulfhydryl, carboxyl and amine groups toward Cd(II). Altogether, its facile and environmentally friendly fabrication, ultrahigh sorption efficiencies, and rapid kinetics demonstrate that MgAl-LDH/Cys has potential for practical applications in heavy metal remediation.

Adsorption of Heavy Metals in Contaminated Water Using Zeolite Derived from Agro-Wastes and Clays: A Review

Due to climate change and anthropogenic activities such as agriculture, mining, and urbanization, water contamination has become a very real modern problem. Modern solutions such as activated carbon, reverse osmosis, and ultrafiltration, among others, have been employed in the decontamination of water. These methods are, however, expensive to set up and maintain and therefore have proved a challenge to implement in developing countries. Zeolite materials exhibit excellent structural properties, such as high ion exchange capacity, porosity, and relative surface area, which make them attractive to water decontamination processes. However, conventional zeolites are expensive, and recent research has focused on utilizing low-cost materials such as agro-wastes and clays as raw materials for the synthesis of zeolites. This review aims to discuss the role of low-cost zeolites in their removal of heavy metals and the feasibility of agro-wastes and natural clays in the synthesis of zeolites. Recent research studies based on the synthesis of zeolites from clays and agro-wastes and their application in heavy metal removal have been reviewed and discussed. Agro-wastes such as rice husk ash and sugarcane bagasse ash and layered silicate clays such as kaolinite and smectites are particularly of interest to zeolite synthesis due to their high silica to alumina ratio. Zeolites synthesized through various methods such as hydrothermal, molten salt, and microwave irradiation synthesis have been discussed with their effect on the adsorption of various heavy metals.

Research and Application Progress of Geopolymers in Adsorption: A Review

Geopolymer is a porous inorganic material with a three-dimensional mesh structure, good mechanical properties, a simple preparation process (no sintering) and a low economic cost, and it is environmentally friendly. Geopolymer concrete has been widely used in the construction field, and many other studies have revealed that geopolymer will become one of the most promising inorganic materials with unique structure and properties. This paper provides a review of the development and current status of geopolymers and briefly explains the effects of material proportioning, experimental factors and activators on geopolymer performance. Because of the advantages of high specific surface area and high porosity, geopolymers could be used as adsorbent materials. This paper summarizes the research progresses of the adsorption of metal cations, anions, dyes, and gases by geopolymers, which emphasizes the geopolymer membranes in adsorption, and discusses the challenges and opportunities for the development of more efficient, sustainable and practical adsorption protocols.

Modification of silica nanoparticles by 2,4-dihydroxybenzaldehyde and 5-bromosalicylaldehyde as new nanocomposites for efficient removal and preconcentration of Cu(ii) and Cd(ii) ions from water, blood, and fish muscles

Herein, silica nanoparticles were modified by 2,4-dihydroxybenzaldehyde and 5-bromosalicylaldehyde to produce new nanocomposites which were abbreviated as N₁ and N₂, respectively. The synthesized nanocomposites were used for efficient removal and preconcentration of Cu(ii) and Cd(ii) ions from water, blood, and fish muscles. FE-SEM, FT-IR, XRD, CHN elemental analysis, and nitrogen gas sorption analyzer were used to characterize the new nanocomposites. The XRD proved that the synthesized oxide is cristobalite with an average crystallite size of 54.80 nm. Due to the formation of the C Created by potrace 1.16, written by Peter Selinger 2001-2019 ]]> N group, the intensity of the XRD peak at 2θ = 21.9° in the N₁ and N₂ nanocomposites decreased significantly. The FT-IR bands, which appeared at 1603 and 1629 cm⁻¹ in the N₁ and N₂ nanocomposites, are attributable to the bending vibration of CN and/or OH, respectively. Also, the FE-SEM analysis shows the morphology of the silica nanoparticles which were identified as spherical and rod-like with slight agglomeration while the N₁ and N₂ nanocomposites have flaky surfaces due to the formation of CN groups. The maximum Cu(ii) ion adsorption capacities of the N₁ and N₂ nanocomposites are 64.81 and 40.93 mg g⁻¹, respectively. The maximum Cd(ii) ion adsorption capacities of the N₁ and N₂ nanocomposites are 27.39 and 26.34 mg g⁻¹, respectively. The adsorption of Cu(ii) or Cd(ii) ions using the synthesized nanocomposites is spontaneous, chemical, exothermic, and well-matched with the Langmuir equilibrium isotherm. The recovery findings demonstrate that the preconcentration process is accurate, adaptable, and resulted in quantitative separation because % Recovery is more than 95%. Furthermore, the % RSD was less than 3.5%, indicating good reproducibility.

Herein, silica nanoparticles were modified by 2,4-dihydroxybenzaldehyde and 5-bromosalicylaldehyde to produce new nanocomposites which were abbreviated as N₁ and N₂, respectively.

A Mesoporous Faujasite Prepared by Space-Confined Method for Highly Effective Selectivity of Copper Ions

The discharge of copper ion (Cu(II)) into natural waters can lead to serious environmental and health problems; however, an abundantly porous hierarchical adsorbent, such as faujasite (FAU), can rapidly remove unwanted Cu(II). In this research, a hierarchically structured, abundantly mesoporous faujasite (FAU) was fabricated from industrial-waste lithium-silicon powder (LSP), with the addition of biochar and graphene oxide (GO) via hydrothermal synthesis without high-temperature calcination. The results demonstrated that just a small amount of biochar or GO can significantly improve the mesopore volume (0.14 cm³/g) and the Cu(II) adsorption capacity (115.65 mg/g) of composite FAU. In particular, careful examination of the properties of the composite FAU showed that the biochar and GO had favorably affected the growth of the zeolite crystals, thus promoting the formation of the FAU skeleton structure, ion-exchange sites and Si-OH. The composite FAU exhibited superior adsorption capacities and highly effective Cu(II) selectivity. Thus, the findings of this study provide a novel and cost-effective avenue for the synthesis of composite FAU with high copper-selective removal capacity.

Synthesis of Iron-Based Carbon Microspheres with Tobacco Waste Liquid and Waste Iron Residue for Cd(II) Removal from Water and Soil

Herein, a novel magnetic iron-based carbon microsphere was prepared by cohydrothermal treatment of tobacco waste liquid (TWL) and waste iron residue (WIR) to form WIR@TWL. After that, WIR@TWL was coated with sodium polyacrylate (S.P.) to fabricate WIR@TWL@SP, whose removal efficiency for bivalent cadmium (Cd(II)) was studied in water and soil. As a result, WIR@TWL@SP possessed a high Cd(II) removal efficiency, which could reach 98.5% within 2 h. The adsorption process was consistent with the pseudo-second-order kinetic model because of the higher value of adjusted R2 (0.99). The thermodynamic data showed that the adsorption process was spontaneous (ΔG° < 0) and exothermic (ΔH° = 32.42 KJ·mol-1 > 0). Cd(II) removal mechanisms also include cation exchange, electrostatic attraction, hydrogen-bond interaction, and cation-π interaction. Notably, pot experiments demonstrated that WIR@TWL@SP could effectively reduce Cd absorption by plants in water and soil. Thus, this study offers an effective method for remediating Cd(II)-contaminated water and soil and may have a practical application value.

Recent Advances in Functional Materials for Wastewater Treatment: From Materials to Technological Innovations

The growing concerns about climate changes and environmental pollution have galvanized considerable research efforts in recent years to develop effective and innovative remediation technologies for contaminated soils and water caused by industrial and domestic activities. In this context, the establishment of effective treatment methods for wastewater has been critically important and urgent, since water pollution can take place on a very large scale (e.g., oceanic oil spills) and have massive impacts on ecosystems and human lives. Functional materials play a central role in the advancement of these technologies due to their highly tunable properties and functions. This article focuses on reviewing the recent progress in the application of various functional materials for wastewater treatment. Our literature survey is first concentrated on new modification methods and outcomes for a range of functional materials which have been actively investigated in recent years, including biofilm carriers, sand filters, biomass, biopolymers, and functional inorganic materials. Apart from the development of modified functional materials, our literature survey also covers the technological applications of superhydrophilic/superhydrophobic meshes, hybrid membranes, and reusable sponges in oil–water separation. These devices have gained significantly enhanced performance by using new functional materials as the key components (e.g., coating materials), and are therefore highly useful for treatment of oily wastewater, such as contaminated water collected from an oil spill site or oil–water emulsions resulting from industrial pollution. Based on our state-of-the-art literature review, future directions in the development and application of functional materials for wastewater treatment are suggested.

Immobilization of strontium in geopolymers activated by different concentrations of sodium silicate solutions

Sodium silicate is always used as an activator for the synthesis of geopolymer. However, the effect of sodium silicate concentration on the geopolymer used as adsorbent was still unclear. Therefore, the immobilization of Sr²⁺ in geopolymers activated by different concentrations of sodium silicate was studied through kinetic and isotherm modeling and solid characterizations including XRD, FTIR, TG, SEM-EDS, and N₂ adsorption-desorption isotherm. The adsorption amount of Sr²⁺ decreased with the sequence of S1, S2, and S3. According to the kinetic and isotherm modeling results, these sorption processes fitted better with pseudo-second-order, mainly governed by film diffusion. However, the diffusion mode was gradually closed to particle diffusion as for the sequence of S3, S2, and S1. Besides, the Langmuir model can be more befitting to sorption data than the Freundlich model, and the free energies decreased with the order of S1, S2, and S3. In addition, the specific surface areas did not change regularly with S1, S2, and S3. Thus, the distribution of Al tetrahedrons has a decisive role in the sorption process of Sr²⁺, even though the specific surface area is also a critical factor. More Al tetrahedrons can be formed under the activation of sodium silicate with higher concentration, leading to the low Si/Al molar ratio of the as-synthesized geopolymer.

Applications of Nano-Zeolite in Wastewater Treatment: An Overview

Nano-zeolite is an innovative class of materials that received recognition for its potential use in water and tertiary wastewater treatment. These applications include ion-exchange/sorption, photo-degradation, and membrane separation. The aim of this work is to summarize and analyze the current knowledge about the utilization of nano-zeolite in these applications, identify the gaps in this field, and highlight the challenges that face the wide scale applications of these materials. Within this context, an introduction to water quality, water and wastewater treatment, utilization of zeolite in contaminant removal from water was addressed and linked to its structure and the advances in zeolite preparation techniques were overviewed. To have insights into the trends of the scientific interest in this field, an in-depth analysis of the variation in annual research distribution over the last decade was performed for each application. This analysis covered the research that addressed the potential use of both zeolites and nano-zeolites. For each application, the characterization, experimental testing schemes, and theoretical analysis methodologies were overviewed. The results of the most advanced research were collected, summarized, and analyzed to allow an easy visualization and comparison of these research results. Finally, the gaps and challenges that face these applications are concluded.

CO2 adsorption performance of template free zeolite A and X synthesized from rice husk ash as silicon source

In this work, zeolite NaA (RA) and NaX (RX) have been successfully synthesized using rice husk ash and it is a low cost synthesis process and it does not produce environmental hazards. Sodium silicate (SS) is extracted from rice husk ash which is an alternative silica source for zeolite synthesis. The zeolites are prepared by using a SS silica source extracted from the rice husk ash, and it has been used as an adsorbent for the CO₂ adsorption process which may help in controlling the global warming problems. The zeolites are synthesized by a hydrothermal method without using any organic templating agent. FESEM and TEM micrographs revealed that the synthesized zeolites RA and RX have “Ice cube” and octahedral morphology respectively. From the N₂ sorption studies, the BET surface area of the synthesized zeolites have been found and are 106.25 m² g⁻¹ and 512.79 m² g⁻¹ respectively. The maximum CO₂ adsorption capacities of zeolite RA and RX are 2.22 and 2.45 mmol g⁻¹, respectively at a temperature of 297.15 K. The recorded data are fitted by using non-linear adsorption isotherm models of Langmuir, Freundlich and Toth isotherm models. The fitted isotherm models are observed to be a type I adsorption isotherm according to the IUPAC classification criterion.

In this work, zeolite NaA (RA) and NaX (RX) have been successfully synthesized using rice husk ash as source and it is a low cost synthesis process and it does not produce any environmental hazards.

Dispersed FeOx nanoparticles decorated with Co2SiO4 hollow spheres for enhanced oxygen evolution reaction

Oxygen evolution reaction (OER) has drawn ever-increasing attention because of its essential role in various renewable-energy technologies. In spite of tremendous research efforts, developing high-performance OER catalysts at low cost remains a great challenge. Inspired by two earth-abundant elements Fe and Si, herein, we report a Fe-Co₂SiO₄ composite consisting of well dispersed iron oxide (FeO_x) decorated Co₂SiO₄ hollow nanospheres as an economical and promising OER catalyst. Although Co₂SiO₄ or FeO_x alone has little OER activity, their composite exhibits satisfied performance, that is highly related to geometric effect and bimetal component electronic interactions. The Fe-Co₂SiO₄ composite exhibits comparable catalytic activity to most of transition mental oxide/hydroxide relevant composites at 10 mA cm^-2. It is even 1.6 times higher than commercial RuO₂ electrocatalyst at high current density 100 mA cm^-2 in alkaline solution. In this work, surface decoration of transition metal silicate provides a new horizon to design high-performance and economical OER catalysts.