Enhanced biodegradation of n-hexane in a two-phase partitioning bioreactor inoculated with Pseudomonas mendocina NX-1 under chitosan stimulation

Bioanode boosts efficacy of chlorobenzenes-powered microbial fuel cell: Performance, kinetics, and mechanism

Microbial fuel cell (MFC) is a promising device for water decontamination and energy generation. However, the correlation between power generation and pollutant degradation has not been clarified. Herein, a ruthenium-activated carbon (Ru-AC) bioanode was constructed for chlorobenzenes (CBs) treatment. The pollutant tolerance was improved by Ru-AC anode, and the minimum removal efficiencies of CB and ortho-dichlorobenzene (o-DCB) reached 75.1 % and 69.3 %, respectively, which were considerably higher than those of other MFCs (16.3 %-39.7 %). Correspondingly, the maximum output voltage reached 360.7 mV for the Ru-AC anode, whereas the values obtained from others reached 45.2-149.6 mV. Interaction models were introduced to quantify the relationship between power generation and pollutant degradation. The conversion of highly toxic chlorophenols to organic acids could be accelerated by boosting the mass and electron transfer, thereby simultaneously enhancing CBs removal and power generation. This work provided important insights into pollutant-powered MFC development.

Decoding the influence of low temperature on biofilm development: The hidden roles of c-di-GMP

Biofilms are widely used and play important roles in biological processes. Low temperature of wastewater inhibits the development of biofilms derived from wastewater activated sludge. However, the specific mechanism of temperature on biofilm development is still unclear. This study explored the mechanism of temperature on biofilm development and found a feasible method to enhance biofilm development at low temperature. The amount of biofilm development decreased by approximately 66 % and 55 % at 4 °C and 15 °C, respectively, as compared to 28 °C. The cyclic dimeric guanosine monophosphate (c-di-GMP) concentration also decreased at low temperature and was positively correlated with extracellular polymeric substance (EPS) content, formation, and adhesion strength. Microbial community results showed that low temperature inhibited the normal survival of most microorganisms, but promoted the growth of some psychrophile bacteria like Sporosarcina, Caldilineaceae, Gemmataceae, Anaerolineaceae and Acidobacteriota. Further analysis of functional genes demonstrated that the abundance of functional genes related to the synthesis of c-di-GMP (K18968, K18967 and K13590) decreased at low temperature. Subsequently, the addition of exogenous spermidine increased the level of intracellular c-di-GMP and alleviated the inhibition effect of low temperature on biofilm development. Therefore, the possible mechanism of low temperature on biofilm development could be the inhibition of the microorganism activity and reduction of the communication level between cells, which is the closely related to the EPS content, formation, and adhesion strength. The enhancement of c-di-GMP level through the exogenous addition of spermidine provides an alternative strategy to enhance biofilm development at low temperatures. The results of this study enhance the understanding of the influence of temperature on biofilm development and provide possible strategies for enhancing biofilm development at low temperatures.

Enhancement of gaseous chlorobenzene biodegradation and power generation in a microbial fuel cell by bifunctional Acinetobacter sp. HY-99C

The efficient biodegradation of volatile chlorinated hydrocarbons using microbial fuel cells (MFCs) offers a feasible approach for purifying waste gas and alleviating energy crises. However, power generation is limited by poor pollutant biodegradation and slow electron transfer. The bifunctional bacterium Acinetobacter sp. HY-99C was screened and used to improve the performance of a conventional MFC. The inoculation of strain HY-99C into the conventional MFC promoted the formation of a compact biofilm with high metabolic activity and an enriched bifunctional genus (Acinetobacter), which resulted in the accelerated decomposition of chlorinated aromatic compounds into biodegradable organic acids. This led to efficient chlorobenzene removal and power generation from the MFC, with a chlorobenzene elimination capacity of 70.8 g m-3 h-1 and power density of 89.6 mW m-2, which are improved over those of previously reported MFCs. This study provides novel insights into enhancing pollutant removal and power generation in MFCs.

Surfactants Influencing the Biocatalytic Performance of Natural Alkane-Degrading Bacteria via Interfacial Biocatalysis in Pickering Emulsions

Setting superhydrophobic Mycobacterium sp. as an example, the hydrophobic bacteria acting as demulsifying agents of surfactant-stabilized conventional emulsions, vice versa, the synergistic/antagonistic influence of nonionic surfactants (Tween 80 or Span 80) on the stability of the bacteria-stabilized Pickering emulsions was investigated. At the same time, the activated/suppression effect of nonionic surfactants on microbial degradation of tetradecane, which exhibited a dose-response relationship, was also found. The hydrophobic bacteria acting as demulsifying agents and the suppression influence of nonionic surfactants on the biocatalytic performance (indexing as biomass) of natural alkane-degrading bacteria, believed to be totally separated concepts previously, are for the first time found to be closely related to in situ surface modification of bacteria with nonionic surfactants. During the degradation of tetradecane by Mycobacterium sp. in the presence of nonionic surfactants, demulsification due to the bacteria acting as demulsifying agents and interfacial biocatalysis in the bacteria-stabilized Pickering emulsions are involved, which provides useful information to select optimal dispersants for marine oil spills.

Biofilm metagenomic characteristics behind high coulombic efficiency for propanethiol deodorization in two-phase partitioning microbial fuel cell

Hydrophobic volatile organic sulfur compounds (VOSCs) are frequently found during sewage treatment, and their effective management is crucial for reducing malodorous complaints. Microbial fuel cells (MFC) are effective for both VOSCs abatement and energy recovery. However, the performance of MFC on VOSCs remains limited by the mass transfer efficiency of MFC in aqueous media. Inspired by two-phase partitioning biotechnology, silicone oil was introduced for the first time into MFC as a non-aqueous phase (NAP) medium to construct two-phase partitioning microbial fuel cell (TPPMFC) and augment the mass transfer of target VOSCs of propanethiol (PT) in the liquid phase. The PT removal efficiency within 32 h increased by 11-20% compared with that of single-phase MFC, and the coulombic efficiency of TPPMFC (11.01%) was 4.32-2.68 times that of single-phase MFC owing to the fact that highly active desulfurization and thiol-degrading bacteria (e.g., Pseudomonas, Achromobacter) were attached to the silicone oil surface, whereas sulfur-oxidizing bacteria (e.g., Thiobacillus, Commonas, Ottowia) were dominant on the anodic biofilm. The outer membrane cytochrome-c content and NADH dehydrogenase activity improved by 4.15 and 3.36 times in the TPPMFC, respectively. The results of metagenomics by KEGG and COG confirmed that the metabolism of PT in TPPMFC was comprehensive, and that the addition of a NAP upregulates the expression of genes related to sulfur metabolism, energy generation, and amino acid synthesis. This finding indicates that the NAP assisted bioelectrochemical systems would be promising to solve mass-transfer restrictions in low solubility contaminates removal.

Efficient biodechlorination at the Fe3O4-based silicone powder modified chlorobenzene-affinity anode

The treatment of chlorinated volatile organic compounds faces challenges of secondary pollution and less-efficiency due to the substitution of chlorine. Microbial fuel cells (MFCs) provide a promising opportunity for its abatement. In this study, a novel Fe3O4 nanoparticles and silicone-based powder (SP) were integrated and immobilized on carbon felt (CF+Fe3O4@SP), which was further used as anode in the chlorobenzene (CB) powered MFC. Owing to the cooperation between SP and Fe3O4, the anode exhibited excellent performance for both biodechlorination and power generation. The results indicated that the CF+Fe3O4@SP anode loaded MFC achieved 98.5% removal of 200 mg/L CB within 28 h, and the maximum power density was 675.9 mW/m3, which was a 45.6% increase compared to that of the bare CF anode. Microbial community analysis indicated that the genera Comamonadaceae, Pandoraea, Obscuribacteraceae, and Truepera were dominated, especially, the Comamonadaceae and Obscuribacteraceae showed outstanding affinity for Fe3O4 and SP, respectively. Moreover, the proportion of live bacteria, secretion of extracellular polymer substances, and protein content in the extracellular polymer substances were significantly increased by modifying Fe3O4@SP onto the carbon-based anode. Thus, this study provides new insights into the development of MFCs for refractory and hydrophobic volatile organic compounds removal.

Adding nanoparticles to improve emulsion efficiency and enhance microbial degradation in Pickering emulsions

Interfacial microbial degradation of alkane in Pickering emulsions stabilized by hydrophobic bacterial cells is a new mechanism for microbial degradation of water-insoluble chemicals, where both water-insoluble chemicals in the oil phase and water-soluble nutrients (such as nitrogen and phosphorus) in the water phase are bio-accessible to living microorganisms anchoring onto the oil-water interfaces. In the present work, super-hydrophobic Mycobacterium sp. (contact angle 168.6°) degradation of tetradecane was set up as a model. Addition of fumed SiO2 particles (Aerosil® R974) as a new strategy was developed to enhance tetradecane degradation where the biodegradation rate (based on the accumulated biomass) increased by approximately 80%. The enhanced effect of SiO2 particles on the tetradecane degradation attributed to the synergistic effect of SiO2 particles on the emulsion efficiency of Pickering emulsions stabilized by bacterial cells and then on the enhancement of interfacial microbial degradation in Pickering emulsions. KEY POINTS: • Interfacial microbial degradation in bacterial cells stabilized Pickering emulsions. • Adding fumed SiO2 particles to enhance microbial degradation of tetradecane. • Correlation relationship between emulsion efficiency and interfacial microbial degradation.

Enhanced removal of mixed VOCs with different hydrophobicities by Tween 20 in a biotrickling filter: Kinetic analysis and biofilm characteristics

Mass transfer limitation usually causes the poor performance of biotrickling filters (BTFs) for the treatment of hydrophobic volatile organic compounds (VOCs) during long-term operation. In this study, two identical lab-scale BTFs were established to remove a mixture of n-hexane and dichloromethane (DCM) gases using non-ionic surfactant Tween 20 by Pseudomonas mendocina NX-1 and Methylobacterium rhodesianum H13. A low pressure drop (≤110 Pa) and a rapid biomass accumulation (17.1 mg g^-1) were observed in the presence of Tween 20 during the startup period (30 d). The removal efficiency (RE) of n-hexane was enhanced by 15.0%- 20.5% while DCM was completely removed with the inlet concentration (IC) of 300 mg·m^-3 at different empty bed residence times in the Tween 20 added BTF. The viable cells and the relative hydrophobicity of the biofilm were increased under the action of Tween 20, which facilitated the mass transfer and enhanced the metabolic utilization of pollutants by microbes. Besides, Tween 20 addition enhanced the biofilm formation processes including the increased extracellular polymeric substance (EPS) secretion, biofilm roughness and biofilm adhesion. The kinetic model simulated the removal performance of the BTF with Tween 20 for the mixed hydrophobic VOCs, and the goodness-of-fit was above 0.9.

Effects of bamboo-charcoal modified by bimetallic Fe/Pd nanoparticles on n-hexane biodegradation by bacteria Pseudomonas mendocina NX-1

The high hydrophobicity of n-hexane is the main reason why it is difficult to be removed biologically. In this study, the effects of bamboo-charcoal modified by bimetallic Fe/Pd (BBC) on n-hexane biodegradation by Pseudomonas mendocina NX-1 (PM) was investigated. The n-hexane removal efficiency was increased in the presence of BC. The highest n-hexane removal efficiency at 90.0% was achieved at 0.05 g L^-1 BCE and 3 g L^-1 NH₄⁺ under pH 7.7 and 35 °C. Additionally, protein content (45.9 μg mL^-1) and negative cell surface zeta potential (-26.4 mV) were increased during biodegradation process, with PM-BBC being 43.1 μg mL^-1 and 19.1 mV. Bacterial growth was improved and maximum cell surface hydrophobicity was obtained after 20 h, which was 59.4% higher than the control with PM-BBC (37.7%) or PM (16.1%), showing biodegradation products of 1-butanol and acetic acid. The results indicate that BBC improved n-hexane biodegradation efficiency by promoting bacterial growth, reducing cell zeta potential, exposing hydrophobic proteins, and increasing cell surface hydrophobicity of bacterial strain NX-1. This investigation suggests that BBC-enhanced biodegradation can be promising to treat n-hexane-containing gas.

Dechlorination of dichloromethane by a biofilter enriched with electroactive bacteria: Performance, kinetics, and microbial community

Dichloromethane (DCM) is a recalcitrant volatile organic compound that exhibits biological toxicity and bioaccumulation. In this study, gaseous DCM was removed using an electroactive bacterial biofilter (EBB) with graphite rod as the anode and carbon felt as the cathode. The highest removal efficiency (97.09%) was achieved at a cathodic potential of -600 mV (vs. Ag/AgCl). The EBB had a maximum elimination capacity of 79.29 g m^-3 h^-1 when the inlet load was 96.48 g m^-3 h^-1. There was no substrate inhibition phenomenon observed in the EBB, and the Michaelis-Menten model was used to describe the kinetics of the EBB. High-throughput sequencing indicated that electroactive genera such as Rhodanobacter sp., Sphingomonas sp., Pseudomonas sp., Chryseobacterium sp., Pseudochrobactrum sp., and Mycobacterium sp. dominated the EBB. The microbial communities were stable and were slightly affected by the DCM inlet concentration. The results can be applied for the effective treatment of recalcitrant volatile organic compounds (VOCs).

Newly isolated Enterobacter cloacae sp. HN01 and Klebsiella pneumoniae sp. HN02 collaborate with self-secreted biosurfactant to improve solubility and bioavailability for the biodegradation of hydrophobic and toxic gaseous para-xylene

The gas-liquid mass transfer rate of hydrophobic volatile organic compounds (VOCs) is the limiting step in a biological treatment system. The present study aimed to utilize self-producing biosurfactants to enhance the bioavailability of hydrophobic gaseous VOCs. Two novel gram-negative rod-shaped bacteria, Enterobacter cloacae strain HN01 and Klebsiella pneumoniae strain HN02 were successfully isolated from sewage sludge by using blood agar and methylene blue agar plates. The two strains can use para-xylene (PX), a hydrophobic VOC model, as the only carbon source for biosurfactant production. Both strains can produce glycolipid biosurfactants, as confirmed by the emulsification index, Nuclear magnetic resonance, and Fourier transform infrared spectroscopy. Results indicated that PX can be completely decomposed at an initial concentration of 15.50 mg L^-1, pH value of 7.0, and temperature of 30 °C within 36 h. The Yano model is suitable for the prediction of the growth kinetics of strains over the entire PX concentration range. Gas chromatography/mass spectrometry analysis indicated that PX was converted into four and four intermediates in the presence of the strains HN01 and HN02, respectively, and the possible mechanisms were proposed. The results can be used in purifying industrial hydrophobic gaseous VOCs and improving the bioavailability of VOCs with self-produced biosurfactants.

Airlift two-phase partitioning bioreactor for dichloromethane removal: Silicone rubber stimulated biodegradation and its auto-circulation

Solid non-aqueous phases (NAPs), such as silicone rubber, have been used extensively to improve the removal of volatile organic compounds (VOCs). However, the removal of VOCs is difficult to be further improved because the poor understanding of the mass transfer and reaction processes. Further, the conventional reactors were either complicated or uneconomical. In view of this, herein, an airlift bioreactor with silicone rubber was designed and investigated for dichloromethane (DCM) treatment. The removal efficiency of Reactor 1 (with silicone rubber) was significantly higher than that of Reactor 2 (without silicone rubber), with corresponding higher chloride ion and CO₂ production. It was found that Reactor 1 achieved a much better DCM shock tolerance capability and biomass stability than Reactor 2. Silicone rubber not only enhanced the mass transfer in terms of both gas/liquid and gas/microbial phases, but also decreased the toxicity of DCM to microorganisms. Noteworthily, despite the identical inoculum used, the relative abundance of potential DCM-degrading bacteria in Reactor 1 (91.2%) was much higher than that in Reactor 2 (24.3%) at 216 h. Additionally, the silicone rubber could be automatically circulated in the airlift bioreactor due to the driven effect of the airflow, resulting in a significant reduction of energy consumption.

Design of nutrient gas-phase bioreactors: a critical comprehensive review

To reach an efficient and economical gas-phase bioreactor is still one of the most critical challenges in biotechnology engineering. The numerous advantages of gas-phase bioreactors (GPBs) as well as disadvantages of these bioreactors should be exactly recognized, and efforts should be made to eliminate these defects. The first step in upgrading these bioreactors is to identify their types and the results of previous research. In the present work, a summary of the studies carried out in the field of cultivation in these bioreactors, their classification, their components, their principles and relations governing elements, modeling them, and some of their inherent engineering aspects are presented. Literature review showed that inoculation of shoots, roots, adventurous roots, callus, nodal explants, anther, nodal segment, somatic embryo, hairy roots, and fungus is reported in 15, 2, 2, 2, 3, 2, 1, 1, 37, and 5 cases, respectively.

Interfacial biodegradation of phenanthrene in bacteria-carboxymethyl cellulose-stabilized Pickering emulsions

The limited bioavailability of PAHs in non-aqueous phase liquid (NAPL) limits their degradation. The biodegradation of phenanthrene in n-tetradecane by hydrophilic bacterium Moraxella sp. CFP312 was studied with the assistance of two polymers, chitosan and carboxymethyl cellulose (CMC). Both chitosan and CMC improved the cell hydrophobicity of CFP312 and increased the contact angle of CFP312 cells from 30.4 to 78.5 and 88.5, respectively. However, CMC increased the degradation ratio of phenanthrene from 45 to nearly 100%, while chitosan did not cause any improvement. We found that CMC was more effective than chitosan in promoting CFP312 to stabilize Pickering emulsion. In the bacteria-CMC complex system, oil was dispersed into small droplets to obtain a high emulsification index and large specific surface area. Moreover, according to the microscopic image of the bacteria-CMC emulsion droplet, we observed that the droplet surface was tightly covered by the CFP312 cells. Therefore, CFP312 cells joined with CMC can utilize phenanthrene in oil phase at the oil-water interface. This study will offer a new strategy for effective microbial degradation of hydrophobic compounds in NAPLs by hydrophilic bacteria. KEY POINTS: • Biodegradation of phenanthrene in Pickering emulsions • Pickering emulsions stabilized by hydrophilic CFP312 joined with CMC. • Phenanthrene was degraded by CFP312 at oil-water interface.

Two quorum sensing enhancement methods optimized the biofilm of biofilters treating gaseous chlorobenzene

In this study, effects of two quorum sensing (QS) enhancement methods on the performance and biofilm of biofilters treating chlorobenzene were investigated. Three biofilters were set up with BF1 as a control, BF2 added exogenous N-acyl-homoserine lactones (AHLs) and BF3 inoculated AHLs-producing bacterium identified as Acinetobacter. The average chlorobenzene elimination capacities were 73 and 77 g/m³/h for BF2 and BF3 respectively, which were significantly higher than 50 g/m³/h for BF1. The wet biomass of BF2 and BF3 with QS enhancement eventually increased to 60 and 39 kg/m³ respectively, and it was 29 kg/m³ for BF1. Analysis on biofilms in three biofilters showed that distribution uniformity, extracellular polymeric substances production, adhesive strengths, viability, and metabolic capacity of biofilms were all prompted by the two QS enhancement methods. Comparisons between the two QS enhancement methods showed that adding exogenous AHLs had more significant enhancing effect on biofilm due to its higher AHLs level in start-up period, while AHLs-producing bacteria had an advantage in enhancing bacterial community diversity. These results demonstrate that QS enhancement methods have the potential to optimize the biofilm and thus improve the performance of biofilters treating recalcitrant VOCs.