Seasonal variation and spatial distribution of microplastics in tertiary wastewater treatment plant in South Korea

Migration and transformation modes of microplastics in reclaimed wastewater treatment plant and sludge treatment center with thermal hydrolysis and anaerobic digestion

Microplastics in wastewater have been investigated globally, but less research on the migration and transformation of microplastics throughout wastewater and sludge treatment. This study investigated the fate of microplastics in a reclaimed wastewater treatment plant and a centralized sludge treatment center with thermal hydrolysis and anaerobic digestion. The results exhibited that the effluent microplastics of this reclaimed wastewater treatment plant were 0.75 ± 0.26 items/L. Approximately 98 % of microplastics were adsorbed and precipitated into sludge. After thermal hydrolysis, anaerobic digestion and plate and frame dewatering, the removal rate of microplastics was 41 %. Thermal hydrolysis was the most effective method for removing microplastics. Polypropylene, polyamide and polyethylene were widely detected in wastewater and sludge. 30 million microplastics were released into the downstream river and 51.80 billion microplastics entered soil through sludge cake daily. Therefore, substantial microplastics still entered the natural environment despite the high microplastics removal rate of reclaimed wastewater and sludge treatment.

Advances in chemical removal and degradation technologies for microplastics in the aquatic environment: A review

In recent years, global attention has been extensively focused on the water pollution and health risks caused by microplastics(MPs), thereby making the treatment of microplastics a key area of research. Chemical removal and degradation present effective approaches to addressing this issue. Consequently, this review summarizes the latest research advancements in the chemical removal and degradation of microplastics in water, comparing the treatment efficacy and advantages and disadvantages of various removal/degradation techniques. It elucidates the chemical mechanisms underlying the removal/degradation of microplastics and identifies the primary influencing factors during the treatment process. A systematic analysis of the performance of microplastic treatment technologies is conducted, examining the impact of microplastic characteristics, operational conditions, and other parameters on the effectiveness of microplastic treatment.

Are we underestimating stormwater? Stormwater as a significant source of microplastics in surface waters

Stormwater represent a critical pathway for transporting microplastics (MPs) to surface waters. Due to complex dynamics of MPs in stormwater, its dispersion, weathering, risk, and transport are poorly understood. This review bridges those gaps by summarizing the latest findings on sources, abundance, characteristics, and dynamics involved in stormwater MP pollution. Weathering starts before or after MPs enter stormwater and is more pronounced on land due to continuous heat and mechanical stress. Land use patterns, rainfall intensity, MPs size and density, and drainage characteristics influence the transport of MPs in stormwater. Tire and road wear particles (TRWPs), littering, and road dust are major sources of MPs in stormwater. The concentrations of MPs varies from 0.38-197,000 particles/L globally. Further MP concentrations showed regional variations, highlighting the importance of local monitoring efforts needed to understand local pollution sources. We observed unique signatures associated with the shape and color of MPs. Fibers and fragments were widely reported, with transparent and black being the predominant colors. We conclude that the contribution of stormwater to MP pollution in surface waters is significantly greater than wastewater treatment plant effluents and demands immediate attention. Field and lab scale studies are needed to understand its behavior in stormwater and the risk posed to the downstream water bodies.

Fate and potential risks of microplastic fibers and fragments in water and wastewater treatment processes

Water and wastewater treatment plants (WWTPs) receive various types of microplastics (MPs), with fibers and fragments being dominant shapes. Here we investigated the removal behavior and transformation of MPs (polypropylene and polyethylene terephthalate fibers and fragments) in simulated water and wastewater treatment units, including activated sludge process, coagulation, sand filtration, and advanced oxidation/disinfection. Sand filtration demonstrated the highest average efficiency in removing MPs (98 %), followed by activated sludge process (61 %) and coagulation (55 %), which was associated with their physicochemical properties (shape, size, density, surface functional groups, etc). In activated sludge process and coagulation, the polymer type had a greater impact on the removal of MPs than the particle shape, while in sand filtration, the particle shape played a more important role. When subjected to the long-term operation and backwashing of sand filters, approximately 15 % of the initially filtered fragments broke through the sand media, with nearly no fibers escaping. UV-based advanced oxidation and chlorination induced the leaching of dissolved organic matters with different molecular characteristics from fragment MPs, resulting in varying levels of cytotoxicity and bacterial toxicity. Our study provides important information for predicting the fate of MPs and mitigating their impacts in WWTPs.

Interactions between microplastics and Culex sp. larvae in wastewater

Microplastics (MPs) are a growing issue because they endanger both aquatic organisms and humans. Studies have indicated that wastewater treatment plants (WWTPs) are one of the major contributors to MPs in the environment. However, studies on the abundance of MP contamination in WWTPs and its transmission into aquatic organisms are still scarce, especially in Egypt. The goal of this study was to examine the temporal fluctuations in the distribution of MPs in surface water and the dominant macroinvertebrate fauna (Culex sp. larvae) in a fixed wastewater basin in Sohag Governorate, Egypt. The average of MPs in the surface water was 3.01 ± 0.9 particles/L. The results indicated to seasonal variation of MP abundance in the wastewater basin that was significantly higher in winter than in the other seasons. The risk index for polymers (H), pollution load index (PLI), and potential ecological risk index (RI) were used to assess the degree of MP contamination. The basin has moderate H values (<1000) because of the presence of polymers with moderate hazard scores such as polyester (PES), polyethylene (PE), and polypropylene (PP). According to the PLI values, surface water is extremely contaminated with MPs (PLI: 88 to 120). The RI values of surface water showed higher ecological risk (level V). MPs in Culex sp. larvae were seasonally changed with an 85% detection rate, and an abundance average of 0.24 ± 0.65 particles/ind, MP concentration in Culex sp. larvae was influenced by the MP characters (shape, color, and polymer). The larvae of Culex sp. showed a greater preference for black and red fibrous polyester (PES) with sizes (<1000 μm) of MPs. These findings suggest that Culex sp. larvae prefer ingesting MPs that resemble their food. It is possible to overestimate Culex sp.'s preference for lower sizes because of their catabolism of MPs. To better understand the preferences of Culex sp. larvae for MPs, further controlled trials should be conducted. PRACTITIONER POINTS: Wastewater is highly contaminated with microplastics (MPs) in the different seasons. First report of detection of the seasonal abundance of MP in Culex sp. larvae. Culex sp. larvae showed a stronger feeding preference for MPs with specific characteristics. Smaller size and blue polyester fibers were the dominant characteristics of MPs in wastewater.

Microplastics' Shape and Morphology Analysis in the Presence of Natural Organic Matter Using Flow Imaging Microscopy

Ubiquitous microplastics in urban waters have raised substantial public concern due to their high chemical persistence, accumulative effects, and potential adverse effects on human health. Reliable and standardized methods are urgently needed for the identification and quantification of these emerging environmental pollutants in wastewater treatment plants (WWTPs). In this study, we introduce an innovative rapid approach that employs flow imaging microscopy (FlowCam) to simultaneously identify and quantify microplastics by capturing high-resolution digital images. Real-time image acquisition is followed by semi-automated classification using customized libraries for distinct polyethylene (PE) and polystyrene (PS) microplastics. Subsequently, these images are subjected to further analysis to extract precise morphological details of microplastics, providing insights into their behavior during transport and retention within WWTPs. Of particular significance, a systematic investigation was conducted to explore how the presence of natural organic matter (NOM) in WWTPs affects the accuracy of the FlowCam's measurement outputs for microplastics. It was observed that varying concentrations of NOM induced a more curled shape in microplastics, indicating the necessity of employing pre-treatment procedures to ensure accurate microplastic identification when utilizing the FlowCam. These observations offer valuable new perspectives and potential solutions for designing appropriate treatment technologies for removing microplastics within WWTPs.

A holistic approach on the impact of microplastic discharge from WWTPs to the neighboring environment in Southeast Spain

The present study investigated the release of microplastics (MPs) from wastewater treatment plants (WWTPs) to the neighboring environment, including marine and coastal sediments, and fish. Here, we comprehensively investigated MP abundance in 34 samples of marine sediment, corresponding to 5,530.5 g of sediment (d.w.) collected at -8.0 m, -12.5 m, and -24.0 m, 69 samples of coastal sediment, accounting for 13,617.4 g (d.w.) from 17 different beaches from Mar Menor, and stomach and intestine of 17 fish samples of Sparus aurata, in the vicinity of Cartagena, a port city in Southeast Spain. The results showed that MPs were detected in all marine sediment samples, with an average abundance of 19.4 ± 2.4 items/kg (d.w.), in coastal sediments, with an average abundance of 52.5 ± 5.3 items/kg (d.w.), and fish samples, with an average of 8.2 ± 1.4 items per individual. The contribution of MPs from WWTPs to marine sediments is expected to be slow, as effluents were mostly dominated by fiber and film shapes, and by polymers less dense than seawater. There were no significant variations in the MP abundance of marine sediments after the atmospheric phenomenon named DANA, although a significant smaller MP size was reported, indicating a high mobility for tiny sizes. The same results were revealed for coastal sediment, although variations after DANA were statistically significant. Coastal sediment samples closer to WWTPs and agricultural fields with plastic mulching displayed higher MP concentrations, and an increase in the removal rate of MPs from WWTP effluents was negatively correlated with a decrease in MPs from fish collected. This study highlights the importance of sewage treatment plants in transporting MPs to the aquatic and terrestrial surrounding environment, which warrants further research on human health risks associated to MP pollution.

Material flow analysis-based assessment of polypropylene-fiber-containing microplastics released from disposable masks: Characterizing distribution in the environmental media

With the upsurge in the use of disposable masks during the coronavirus disease pandemic, improper disposal of discarded masks and their negative impact on the environment have emerged as major issues. Improperly disposed of masks release various pollutants, particularly microplastic (MP) fibers, which can harm both terrestrial and aquatic ecosystems by interfering with the nutrient cycling, plant growth, and the health and reproductive success of organisms. This study assesses the environmental distribution of polypropylene (PP)-containing MPs, generated from disposable masks, using material flow analysis (MFA). The system flowchart is designed based on the processing efficiency of various compartments in the MFA model. The highest amount of MPs (99.7 %) is found in the landfill and soil compartments. A scenario analysis reveals that waste incineration significantly reduces the amount of MP transferred to landfills. Therefore, considering cogeneration and gradually increasing the incineration treatment rate are crucial to manage the processing load of waste incineration plants and minimize the negative impact of MPs on the environment. The findings provide insights into the potential environmental exposure associated with the improper disposal of waste masks and indicate strategies for sustainable mask disposal and management.

Characteristics and seasonal variation of microplastics in the wastewater treatment plant: The case of Bursa deep sea discharge

Microplastics (MPs) are an emerging pollutant that can be detected in all ecosystems, especially aquatic ecosystems. Wastewater treatment plants (WWTPs) are important point sources of MP release into the sea. In this study, the characteristics of MPs in wastewater and sludge samples taken from different units of WWTP in Bursa-Gemlik district for 12 months were investigated. Wastewater and sludge samples collected from 7 different points were classified as size, shape, color, and counted. The amount of MP in the influent and effluent of the WWTP, respectively; 107.1 ± 40.2 MP/L and 4.1 ± 1.1 MP/L. Although the MP removal efficiency of the WWTP is 96.17 %, approximately 74,825,000 MP is discharged into the Marmara Sea every day. The amount of MP in the sludge is 14.3 ± 7.1 MP/g. The amount of MP accumulated in 22tons of waste sludge formed daily in WWTP was calculated as 314,600,000 MP, and the annual accumulated amount was calculated as approximately 1.15 × 1011 MP. The MPs in the WWTP were mainly 1-0.5 mm in size. Fibers were the dominant MP shape in both the wastewater and sludge samples. Black and transparent were the dominant MP colors. Seven different polymer types of MPs were detected, which were mainly types of polyethylene, polypropylene, and polyethylene terephthalate. Despite the high removal efficiency in the investigated WWTP, it has been shown that it acts as an important source of MPs to the sea ecosystem due to the high discharge rates.

Recent advances on microplastics pollution and removal from wastewater systems: A critical review

Microplastics (MPs) (plastic particles <5 mm) are globally acknowledged as a serious emerging micropollutant, which passes through various pathways in natural habitats and eventually ends up in our food chain. In this context, the present study critically reviews recent advances in MPs sampling and detection, occurrence, fate, and removal in wastewater treatment plants (WWTPs) by delineating their characteristics that manifest toxicity in the environment via effluent discharge. While there is currently no standard protocol in place, this work examined and compared the latest approaches adopted for improved sampling, sample processing, and characterization of MPs via fluorescence imaging and certified reference materials for method validation. MPs concentration from different sources in the WWTPs varies considerably ranging between 0.28 and 18285 MPs/L (raw wastewater), 0.004-750 MPs/L (effluent), and 0.00023-10380 MPs/kg (sludge). Assessment of MPs removal efficiency across different treatment stages in various in WWTPs has been performed and elucidated their removal mechanisms. The overall MPs removal efficiency in primary, secondary, and tertiary treatment stages in WWTPs reported to be around 57-99%, 78.1-99.4%, and 90-99.2%, respectively. Moreover, the review covers advanced treatment methods for removing MPs, including membrane bioreactors, coagulation/flocculation, ultrafiltration, rapid sand filtration, ozonation, disc filtration, and reverse osmosis, which have been found to be highly effective (>99%). Membrane bioreactors have been proclaimed to be the most reliable secondary treatment technique for MPs removal. Coagulation (92.2-95.7%) followed by ozonation (99.2%) as a tertiary treatment chain has been demonstrated to be the most efficient in removing MPs from secondary-treated wastewater effluent. Further, the review delineates the effect of different treatment stages on the physical and chemical characteristics of MPs, associated toxicity, and potential impact factors that can influence the MPs removal efficiency in WWTPs. Conclusively, the merits and demerits of advanced treatment techniques to mitigate MPs pollution from the wastewater system, research gaps, and future perspectives have been highlighted.

Microplastic emission trends in Turkish primary and secondary municipal wastewater treatment plant effluents discharged into the Sea of Marmara and Black Sea

Wastewater Treatment Plants (WWTPs) are recognized as one of the primary sources of microplastics, a class of contaminants that has lately gained attention. The quantity of MP that WWTPs release into the environment depends on several factors, including the treatment type, season, and population serviced. MP abundance and characterization were explored in 15 WWTP effluent waters, 9 discharged to the Black Sea from Türkiye and 6 to the Marmara Sea, with varying population densities and treatment methods. The mean MP abundance in primary treatment WWTPs (76.25 ± 49.20 MP L-1) was found to be substantially greater than that in secondary treatment WWTPs (20.57 ± 21.56 MP L-1) (p<0.05). MPs in WWTP effluent waters showed significant seasonal and spatial differences (Two Way ANOVA, Tukey, p<0.05). However, no positive correlation was detected between the population serviced and MP abundance in effluent waters. While the fiber was the dominant shape (49.5%) among MPs in effluent waters, ≈80% of the length was <1000 μm. MPs are classified into polymer types as follows: polyethylene terephthalate (34.9%) > polypropylene (32.4%) > polyethylene (19.9%) > polyamide (11%) > polystyrene (1.2%) > polyvinyl chloride (0.6%). With effluent waters from the WWTPs tested, we calculated that 1.24x1010 daily MPs are discharged into the Black Sea while 4.95x1010 MPs are into the Marmara Sea, for a combined annual discharge of 2.26x1013 MPs highlighting that WWTPs are key contributors of MP in Turkish coastal waters.

Adsorption behavior of triclosan on microplastics and their combined acute toxicity to D. magna

Microplastics (MP) have been recently identified as emerging water contaminants in worldwide. Owing to its physicochemical properties, MP have been considered as a vector of other micropollutants and may affect their fate and ecological toxicity in the water environment. In this study, triclosan (TCS), which is a widely-used bactericide, and three frequently found types of MP (PS-MP, PE-MP, and PP-MP) were investigated. The adsorption behavior of TCS on MP was investigated by the effect of reaction time, initial concentration of TCS, and other water chemistry factors. Elovich model and Temkin model are the most fitted well with kinetics and adsorption isotherms, respectively. The maximum TCS adsorption capacities were calculated for PS-MP (9.36 mg/g), PP-MP (8.23 mg/g), and PE-MP (6.47 mg/g). PS-MP had higher affinity to TCS owing to hydrophobic and π-π interaction. The TCS adsorption on PS-MP was inhibited by decreasing concentrations of cations, and increasing concentration of anion, pH, and NOM concentration. At pH 10, only 0.22 mg/g of adsorption capacity was obtained because of the isoelectric point (3.75) of PS-MP and pKa (7.9) of TCS. And almost no TCS adsorption occurred at NOM concentration of 11.8 mg/L. Only PS-MP had no acute toxic effect on D. magna, whereas TCS showed acute toxicity (EC_50,24h of TCS = 0.36 ± 0.4 mg/L). Although survival rate increased when TCS with PS-MP due to lower the TCS concentration in solution via adsorption, PS-MP was observed in intestine and body surface of D. magna. Our findings can contribute to understanding the combined potential effects of MP fragment and TCS to aquatic biota.

Microplastic biofilm, associated pathogen and antimicrobial resistance dynamics through a wastewater treatment process incorporating a constructed wetland

Microplastics in wastewater are colonized by biofilms containing pathogens and antimicrobial resistance (AMR) genes that can be exported into receiving water bodies. This study investigated establishment and changes in microplastic-associated biofilm and AMR during a conventional full-scale 2100 population equivalent wastewater treatment process combined with a free water surface polishing constructed wetland. Sequential microplastic colonization experiments were conducted at different stages of the wastewater treatment process, including in raw sewage, treated effluent and the constructed wetland. Two scenarios were tested in which the constructed wetland served as either (i) a polishing step or (ii) as primary recipient of sewage inoculated microplastics. Bacterial 16S rRNA gene sequencing was carried out for qualitative bacterial community analysis. qPCR was applied for quantitative analysis of AMR genes (sul1, ermB, tetW, intiI1), bacterial biomass (16S rRNA) and a human fecal marker (HF183). Microbial diversity on microplastics increased with incubation time. The initial sewage-derived biofilm composition changed more significantly in the wastewater effluent compared to the constructed wetland. Pathogen and AMR load decreased by up to two orders of magnitude after coupled conventional and constructed wetland treatment, while less impact was observed when sewage-inoculated microplastic material was directly transferred into the constructed wetland. Aeromonas, Klebsiella, and Streptococcus were key pathogenic genera correlated with AMR in microplastic-associated biofilms. Despite decreasing trends on human pathogens and AMR load along the treatment process, microplastic-associated biofilms were a considerable potential hotspot for AMR (intI1 gene) and accommodated Cyanobacteria and fish pathogens.

Microplastics in urban waters and its effects on microbial communities: a critical review

Microplastic (MP) pollution is one of the emerging threats to the water and terrestrial environment, forcing a new environmental challenge due to the growing trend of plastic released into the environment. Synthetic and non-synthetic plastic components can be found in rivers, lakes/reservoirs, oceans, mountains, and even remote areas, such as the Arctic and Antarctic ice sheets. MPs' main challenge is identifying, measuring, and evaluating their impacts on environmental behaviors, such as carbon and nutrient cycles, water and wastewater microbiome, and the associated side effects. However, until now, no standardized methodical protocols have been proposed for comparing the results of studies in different environments, especially in urban water and wastewater. This review briefly discusses MPs' sources, fate, and transport in urban waters and explains methodological uncertainty. The effects of MPs on urban water microbiomes, including urban runoff, sewage wastewater, stagnant water in plumbing networks, etc., are also examined in depth. Furthermore, this study highlights the pathway of MPs and their transport vectors to different parts of ecosystems and human life, particularly through mediating microbial communities, antibiotic-resistant genes, and biogeochemical cycles. Overall, we have briefly highlighted the present research gaps, the lack of appropriate policy for evaluating microplastics and their interactions with urban water microbiomes, and possible future initiatives.