Effective removal of 4-Aminophenol from aqueous environment by pea (Pisum sativum) shells activated with sulfuric acid: Characterization, isotherm, kinetics and thermodynamics

Surface activity, mechanisms, kinetics, and thermodynamic study of adsorption of malachite green dye onto sulfuric acid-functionalized Moringa oleifera leaves from aqueous solution

In the present study, activated carbon prepared from H2SO4-functionalized Moringa oleifera leaves (ACMOL) was used as a potential adsorbent for the effective removal of malachite green (MG) dye from aqueous media. FT-IR, SEM, EDS, Zeta potential, XRD, BET, proximate, and CHNS analysis techniques were used for surface characterization of the ACMOL. The adsorption efficiency of the ACMOL was investigated as a function of varying adsorbent dosage (0.02-0.2 g/100 mL), pH (3.0-9.0), ionic strength (0.1-0.5 M KCl), urea concentration (0.1-0.5 M), contact time (30-210 min), and temperature (303-323 K). The representative adsorption isotherms belong to the typical L-type. Maximum percentage removal was found to be 84% (124.40 mg/g) for MG dye concentration (30 mg/L) at pH 7.0 and 303 K with ACMOL dose 0.02 g/100 mL. The adsorption kinetics and equilibrium experimental data of MG dye adsorption on the ACMOL were well explained by the pseudo-second-order kinetics (R2 = 0.99) and Langmuir isotherm model (R2 = 0.99), respectively. The value of adsorption and desorption coefficient was found to be 0.036 min-1 and 0.025 mg min-1/L, respectively. Thermodynamic study showed the spontaneous (ΔG° =  - 31.33, - 31.92, and - 32.49 kJ/mol at temperatures 303 K, 313 K, and 323 K, respectively) and exothermic (ΔH° =  - 13.7 kJ/mol) nature of the adsorption with some structural changes occurring on the ACMOL surface (ΔS° = 58.198 J/K·mol).

Surface activity, kinetics, thermodynamics and comparative study of adsorption of selected cationic and anionic dyes onto H3PO4-functionalized bagasse from aqueous stream

The discharge of dyes into the water body creates toxicity to aquatic organisms because of their aromatic structure and difficult degradation. So, the treatment of dye-contaminated wastewater is required before releasing it. In the present study, thermally treated (600 °C) and H3PO4 (55%)-functionalized bagasse, henceforth called thermochemically activated bagasse (TCAB), was synthesized as potential adsorbent for the effective removal of selected cationic and anionic dyes from their aqueous stream. TCAB characterization was done employing FT-IR, SEM, XRD, zeta potential, BET, and PZC techniques. The comparative study shows that the relative adsorption on TCAB followed the sequence, methyl red (185 mg/g) > safranin (178 mg/g) > congo red (146 mg/g) > brilliant green (139 mg/g) > malachite green (130 mg/g) > bromocresol green (94 mg/g). The adsorption efficiency was investigated concerning the effect of change in TCAB dose (0.05-0.3 g/100 mL), initial dye concentration (20-200 mg/L), pH (4.0-10.0), ionic strength (0.1-0.5 M KCl), urea concentration (0.1-0.5 M) and temperature (25-45 °C). The representative adsorption isotherms belong to typical L-type. The time-dependent dye removal was best explained by the pseudo-second-order (PSO) kinetic model (R2 = 0.9859-0.9991), while equilibrium data were best explained by the Freundlich model (R2 = 0.9881-0.9961). Thermodynamic study showed the spontaneous (ΔG0 <0) and exothermic nature (ΔH0 <0) of the adsorption of different cationic and anionic dyes. The cyclic adsorption ability of TCAB for different dyes was checked up to three cycles (185 to 168 mg/L for MR, 178 to 165 mg/L for SF, 146 to 130 mg/L for CR, 139 to 127 mg/L for BG, 130 to 114 mg/L for MG and 94 to 80 mg/L for BCG), and no significant decrease in the adsorption capacity was noticed. So, the present study provides valuable insights into the adsorption of cationic and anionic dyes onto H3PO4-functionalized bagasse. Addressing the adsorptive aspects enhances the clarity, reliability and applicability of the study's findings and contributes to its overall scientific impact.

Comparative Study of 4-Aminophenol Removal from Aqueous Solutions by Emulsion Liquid Membranes Using Acid and Basic Type 1 Facilitations: Optimisation and Kinetics

The molecule 4-aminophenol (4AP) is recognised as a serious environmental pollutant that enters the environment during the manufacture and processing of a variety of industrial processes and through the degradation of some pharmaceutical products. This paper describes a comparative study of 4AP removal from aqueous solutions by emulsion liquid membranes using acid and basic type 1-facilitated transports. The results are explained by analysing the stripping process through both the different relative acid/basic strength of the hydroxyl and amine groups of the 4AP molecule and the hydrogen-bonding capacity with water of the ionisation products generated by the reaction of 4AP with HCl or NaOH. To optimize the 4AP removal process, the influence of different experimental conditions (stripping agent concentration in the product phase, surfactant concentration in the membrane phase, stirring rate, feed phase/emulsion phase volume ratio, product phase/membrane phase volume ratio and emulsification rate and time) were studied. The kinetics of the removal process has been analysed by fitting the experimental results to first order, second order and the Behnajady and Avrami models. The Behnajady model presents an excellent fit, allowing to calculate both the initial removal rate and the maximal removal conversion. Optimal conditions of the removal process obtained through these parameters are in full agreement with those obtained from the experimental study.