New synthetic mercaptoethylamino homopolymer-modified maghemite nanoparticles for effective removal of some heavy metal ions from aqueous solution

Fast and efficient extraction and determination of nonsteroidal anti-inflammatory drugs using poly(8-hydroxyquinoline)-coated magnetic graphene oxide nanocomposite prior to capillary electrophoresis analysis in wastewater, breast milk, and urine samples

In this study, magnetic graphene oxide coated with poly(8-hydroxyquinoline) was successfully synthesized, characterized, and utilized as a novel sorbent for the ultrasonic-assisted dispersive magnetic solid-phase extraction of naproxen and ibuprofen. These analytes served as representative analytes for two nonsteroidal anti-inflammatory drugs in various real samples. Characterization techniques, such as IR, X-ray powder diffraction, field emission scanning electron microscopy, energy-dispersive X-ray-mapping, and Brunauer-Emmett-Teller (BET), were used to confirm the correctness synthesis and preparation of the nanocomposites. Effective parameters on the extraction efficiency were investigated to maximize the analytical performance of the developed method. The dynamic range (1-1000 µg L-1), coefficients of determination (R2 ≥ 0.997), the limits of detection (0.3-1.0 µg L-1), and limit of quantification (1.0-3.0 µg L-1), intra-day and inter-day precisions (3.5%-7.2%) were achieved. The method validation results showed extraction recovery ranging from 80.4% to 96.0% and preconcentration factors ranging from 137 to 140.

Fabricating pentaazatetraethylene modified sulfonated polyacrylamide for dye adsorption from aqueous media: isotherms and kinetics models

In this study, pentaazatetraethylene-modified sulfonated polyacrylamide (PAm-SO3-N5) was synthesized and used as a novel efficient adsorbent to remove calmagite from aqueous media. To this end, a central composite design (CCD) was applied to reduce the number of reaction variables (i.e., adsorbent concentration, temperature, initial concentration, and pH) on calmagite removal. The results showed that calmagite was entirely adsorbed by the PAm-SO3-N5 within 30 min. In addition, a pseudo-second-order (PSO) model was prepared as the optimum formula to fit the kinetics information. The modeling results revealed that film diffusion and adsorption are rate-limiting stages to remove the dyes. Using a Langmuir isotherm to fit the equilibrium data, the highest equilibrium adsorption was calculated to be 1732.5 mg/g. In the present study, the ΔH value indicates that the adsorption is of chemical type. Also, the negative sign of ΔS° shows that PAm-SO3-N5 removes calmagite during a relatively stable process with randomness in the system. The increase in ΔG° values with increasing temperature indicates a descending trend in the feasibility degree of calmagite adsorption. Eventually, recycling the adsorbent for 7 cycles to adsorb calmagite dye showed no remarkable activity loss.

Recycling of Waste Toner Powder as Adsorbent to Remove Aqueous Heavy Metals

The removal of Cd²⁺, Zn²⁺ and Ni²⁺ from metal solutions onto waste toner power (WTP) was investigated. The influence of parameters such as pH, contact time, initial metal concentration and adsorbent dosage was studied in batch adsorption experiments. Batch equilibrium experiments showed that the highest removal efficiency for Zn²⁺ and Cd²⁺ occurs at pH 7, while pH 5 is the most suitable for Ni²⁺ removal. The amount of metal removed (mg/g) improved when increasing the initial concentration, and sorption of heavy metals reached equilibrium in 24 h. Metals’ uptake increased with increasing adsorbent dosage. The adsorption isotherms of Zn²⁺, Cd²⁺ and Ni²⁺ onto WTP fit the Langmuir better than the Freundlich model with correlation coefficient R² values ranging from 0.998 to 0.968 and 0.989 to 0.881, respectively. The data showed that the maximum adsorption capacity of heavy metals, a_max, ranged from 2.42 to 1.61 mg/g, from 6.22 to 2.01 mg/g and from 3.49 to 2.56 mg/g for Ni²⁺, Zn²⁺ and Cd²⁺, respectively, with the three WTPs used in this study. This adsorbent can potentially be used to remove metal ions from wastewater.

Synthesis, optimization, and characterization of biogenic manganese oxide (BioMnOx) by bacterial isolates from mangrove soils with sorbents property towards different toxic metals

Manganese oxidizing bacteria, Bacillus mycoides and Bacillus subtilis were isolated from mangrove soils and optimized for the removal of Mn(II) with simultaneous production of biogenic manganese oxide (BioMnOx). The removal rate of Mn(II) was 90% in 48 h for B. mycoides and 72 h for B. subtilis under the optimized conditions at pH 7, temperature 37 °C, 120 rpm, with 1% inoculum containing 10 mM MnCl₂. Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), Energy dispersive X-Ray analysis (EDAX), Fourier-transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) were used to characterize the synthesized biogenic manganese oxide. BioMnOx by Bacillus mycoides and Bacillus subtilis were identified as Bixbyite (Mn₂O₃) and Hausmannite (Mn₃O₄), respectively, with nano-sized monocrystalline nature. BioMnOx of Bacillus subtilis strain was more efficient in the removal of metals Zn and Co than BioMnOx of Bacillus mycoides except for mercury. The removal property of synthesized BioMnOx could be applied to treat multi-metal containing wastewater.

Recent advances in nanoremediation: Carving sustainable solution to clean-up polluted agriculture soils

Agriculture is one of the foremost significant human activities, which symbolizes the key source for food, fuel and fibers. This activity results in a lot of ecological harms particularly with the excessive usage of chemical fertilizers and pesticides. Different agricultural practices have remained industrialized to advance food production, due to the growth in the world population and to meet the food demand through the routine use of more effective fertilizers and pesticides. Soil is intensely embellished by environmental contamination and it can be stated as "universal incline." Soil pollution usually occurs from sewage wastes, accidental discharges or as byproducts of chemical residues of unrestrained production of numerous materials. Soil pollution with hazardous materials alters the physical, chemical, and biological properties, causing undesirable changes in soil fertility and ecosystem. Engineered nanomaterials offer various solutions for remediation of contaminated soils. Engineered nanomaterial-enable technologies are able to prevent the uncontrolled release of harmful materials into the environment along with capabilities to combat soil and groundwater borne pollutants. Currently, nanobiotechnology signifies a hopeful attitude to advance agronomic production and remediate polluted soils. Studies have outlined the way of nanomaterial applications to restore the eminence of the environment and assist the detection of polluted sites, along with potential remedies. This review focuses on the latest developments in agricultural nanobiotechnology and the tools developed to combat soil or land and or terrestrial pollution, as well as the benefits of using these tools to increase soil fertility and reduce potential toxicity.

Heavy Metal Adsorption Using Magnetic Nanoparticles for Water Purification: A Critical Review

Research on contamination of groundwater and drinking water is of major importance. Due to the rapid and significant progress in the last decade in nanotechnology and its potential applications to water purification, such as adsorption of heavy metal ion from contaminated water, a wide number of articles have been published. An evaluating frame of the main findings of recent research on heavy metal removal using magnetic nanoparticles, with emphasis on water quality and method applicability, is presented. A large number of articles have been studied with a focus on the synthesis and characterization procedures for bare and modified magnetic nanoparticles as well as on their adsorption capacity and the corresponding desorption process of the methods are presented. The present review analysis shows that the experimental procedures demonstrate high adsorption capacity for pollutants from aquatic solutions. Moreover, reuse of the employed nanoparticles up to five times leads to an efficiency up to 90%. We must mention also that in some rare occasions, nanoparticles have been reused up to 22 times.

Nanoadsorbants for the Removal of Heavy Metals from Contaminated Water: Current Scenario and Future Directions

Heavy metal pollution of aquatic media has grown significantly over the past few decades. Therefore, a number of physical, chemical, biological, and electrochemical technologies are being employed to tackle this problem. However, they possess various inescapable shortcomings curbing their utilization at a commercial scale. In this regard, nanotechnology has provided efficient and cost-effective solutions for the extraction of heavy metals from water. This review will provide a detailed overview on the efficiency and applicability of various adsorbents, i.e., carbon nanotubes, graphene, silica, zero-valent iron, and magnetic nanoparticles for scavenging metallic ions. These nanoparticles exhibit potential to be used in extracting a variety of toxic metals. Recently, nanomaterial-assisted bioelectrochemical removal of heavy metals has also emerged. To that end, various nanoparticle-based electrodes are being developed, offering more efficient, cost-effective, ecofriendly, and sustainable options. In addition, the promising perspectives of nanomaterials in environmental applications are also discussed in this paper and potential directions for future works are suggested.

Effective Heavy Metals Removal from Water Using Nanomaterials: A Review

The discharge of toxic heavy metals including zinc (Zn), nickel (Ni), lead (Pb), copper (Cu), chromium (Cr), and cadmium (Cd) in water above the permissible limits causes high threat to the surrounding environment. Because of their toxicity, heavy metals greatly affect the human health and the environment. Recently, better remediation techniques were offered using the nanotechnology and nanomaterials. The attentions were directed toward cost-effective and new fabricated nanomaterials for the application in water/wastewater remediation, such as zeolite, carbonaceous, polymer based, chitosan, ferrite, magnetic, metal oxide, bimetallic, metallic, etc. This review focused on the synthesis and capacity of various nanoadsorbent materials for the elimination of different toxic ions, with discussion of the effect of their functionalization on the adsorption capacity and separation process. Additionally, the effect of various experimental physicochemical factors on heavy metals adsorption, such as ionic strength, initial ion concentration, temperature, contact time, adsorbent dose, and pH was discussed.

A nanosized magnetic metal-organic framework of type MIL-53(Fe) as an efficient sorbent for coextraction of phenols and anilines prior to their quantitation by HPLC

The authors describe the synthesis of a magnetic metal-organic framework (MOF) of type MIL-53(Fe) for coextraction of phenols and anilines from various environmental samples. A quick method for dispersive micro-solid phase extraction (D-μ-SPE) was developed for coextraction of the analytes 4-nitrophenol (4-NP), 4-chlorophenol (4-CP), 4-chloroaniline (4-CA), 1-amino-2-naphtol (1-A2N) and 2, 4-dichloroaniline (2, 4-DCA). The MOF was characterized by SEM, TEM, FT-IR, EDS, thermogravimetry, VSM and XRD. The method was optimized by response surface methodology combined with desirability function approach, specifically with respect to pH value of the sample, amount of sorbent, sorption time, salt concentration, sample volume, type and volume of the eluent, and elution time. Following elution with acetonitrile, the analytes were quantified by HPLC with photodiode array detection. Responses are linear in 0.1-2000 μg·L^-1 concentration ranges. The limits of detection and relative standard deviations (for n = 5) are in the range of 0.03-0.2 μg·L^-1 and 3.5-12.6%, respectively. Enrichment factors are 113, 61, 87, 144 and 114 for 4-NP, 4-CP, 4-CA, 1-A2N and 2,4-DCA, respectively. Recoveries from spiked samples ranged from 39.5 to 93.3%. The magnetic sorbent was successfully applied to the coextraction and determination of the analytes in river, rain and hookah water samples. Graphical abstract Schematic presentation for the synthesis of (a) Fe₃O₄ nanoparticles (NPs) and (b) Fe₃O₄@MIL-53(Fe). Fe₃O₄@MIL-53(Fe) was employed as a new nanosorbent in dispersive micro-solid phase extraction of phenols and anilines. The limits of detection are in the range of 0.03-0.2 μg·L^-1.

Nanomaterials for the Removal of Heavy Metals from Wastewater

Removal of contaminants in wastewater, such as heavy metals, has become a severe problem in the world. Numerous technologies have been developed to deal with this problem. As an emerging technology, nanotechnology has been gaining increasing interest and many nanomaterials have been developed to remove heavy metals from polluted water, due to their excellent features resulting from the nanometer effect. In this work, novel nanomaterials, including carbon-based nanomaterials, zero-valent metal, metal-oxide based nanomaterials, and nanocomposites, and their applications for the removal of heavy metal ions from wastewater were systematically reviewed. Their efficiency, limitations, and advantages were compared and discussed. Furthermore, the promising perspective of nanomaterials in environmental applications was also discussed and potential directions for future work were suggested.

Water-Soluble and Insoluble Polymers, Nanoparticles, Nanocomposites and Hybrids With Ability to Remove Hazardous Inorganic Pollutants in Water

The polymeric materials have presented a great development in adsorption processes for the treatment of polluted waters. The aim of the current review is to present the recent developments in this field of study by examining research of systems like functional water-soluble polymers and water-soluble polymer-metal complexes coupled to ultrafiltration membranes for decontamination processes in liquid-liquid phase. Noticing that a water-soluble polymer can be turned into insoluble compounds by setting a crosslinking point, connecting the polymer chains leading to polymer resins suitable for solid-liquid extraction processes. Moreover, these crosslinked polymers can be used to develop more complex systems such as (nano)composite and hybrid adsorbents, combining the polymers with inorganic moieties such as metal oxides. This combination results in novel materials that overcome some drawbacks of each separated components and enhance the sorption performance. In addition, new trends in hybrid methods combining of water-soluble polymers, membranes, and electrocatalysis/photocatalysis to remove inorganic pollutants have been discussed in this review.

Preparation and characterization of γ-Fe2O3 nanoparticles and investigation of its adsorption performance for sulfide, sulfite and thiosulfate from aqueous solutions using ultrasonic assisted method: Modeling and optimization

Maghemite nanoparticles, as an adsorbent, was used for the removal of sulfur species including sulfide, sulfite and thiosulfate from waste water samples by ultrasonic-assisted adsorption method. The characterization of the prepared nanoparticles was carried out by Fourier transform infrared spectroscopy, scanning electron microscopy, X-ray diffraction and BET technique. The nanoparticles well dispersed in the water. The adsorbent was easily separated magnetically from the solution after loading with adsorbate. According to central composite design, the best experimental conditions including initial pH, the dosage of adsorbent and sonication time were obtained for sulfide, sulfite and thiosulfate. After optimization of the parameters, the removal of analytes in these conditions lead to the highest analytes removal efficiency (above 98%). The adsorption capacity was evaluated using different adsorption isotherm models. The maximum predicted adsorption capacities for sulfide, sulfite and thiosulfate were obtained as 148.5, 122.5 and 119.6mgg^-1, respectively. Then, desorption process of the adsorbed thiosulfate was also investigated using sodium hydroxide solution as the solvent and the other conditions affect to desorption were optimized.

Efficient solid phase extraction of codeine from human urine samples using a novel magnetic molecularly imprinted nanoadsorbent and its spectrofluorometric determination

From a medical or clinical point of view, to assess toxicity, adverse effects, interactions and therapeutic efficiency, monitoring drug levels in body fluids, such as urine and plasma, has become increasingly necessary.