New insights into the reaction capabilities of His195 adjacent to the active site of nitrogenase

Putative reaction mechanism of nitrogenase with a half-dissociated S2B ligand

We have studied whether dissociation of the S2B sulfide ligand from one of its two coordinating Fe ions may affect the later parts of the reaction mechanism of nitrogenase. Such dissociation has been shown to be favourable for the E2-E4 states in the reaction mechanism, but previous studies have assumed that S2B either remains bridging or has fully dissociated from the active-site FeMo cluster. We employ combined quantum mechanical and molecular mechanical (QM/MM) calculations with two density-functional theory methods, r2SCAN and TPSSh. To make dissociation of S2B possible, we have added a proton to this group throughout the reaction. We study the reaction starting from the E4 state with N2H2 bound to the cluster. Our results indicate that half-dissociation of S2B is unfavourable in most steps of the reaction mechanism. We observe favourable half-dissociation of S2B only when NH or NH2 is bound to the cluster, bridging Fe2 and Fe6. However, the former state is most likely not involved in the reaction mechanism and the latter state is only an intermittent intermediate of the E7 state. Therefore, half-dissociation of S2B seems to play only a minor role in the later parts of the reaction mechanism of nitrogenase. Our suggested mechanism with a protonated S2B is alternating (the two N atoms of the substrate is protonated in an alternating manner) and the substrate prefers to bind to Fe2, in contrast to the preferred binding to Fe6 observed when S2B is unprotonated and bridging Fe2 and Fe6.

What triggers the coupling of proton transfer and electron transfer at the active site of nitrogenase?

In converting N2 to NH3 the enzyme nitrogenase utilises 8 electrons and 8 protons in the complete catalytic cycle. The source of the electrons is an Fe4S4 reductase protein (Fe-protein) which temporarily docks with the MoFe-protein that contains the catalytic active cofactor, FeMo-co, and an electron transfer cluster called the P cluster. The overall mechanism involves 8 repetitions of a cycle in which reduced Fe-protein docks with the MoFe-protein, one electron transfers to the P-cluster, and then to FeMo-co, followed by dissociation of the two proteins and re-reduction of the Fe-protein. Protons are supplied serially to FeMo-co by a Grotthuss proton translocation mechanism from the protein surface along a conserved chain of water molecules (a proton wire) that terminates near S atoms of the FeMo-co cluster [CFe7S9Mo(homocitrate)] where the multiple steps of the chemical conversions are effected. It is assumed that the chemical mechanisms use proton-coupled electron-transfer (PCET) and that H atoms (e- + H+) are involved in each of the hydrogenation steps. However there is neither evidence for, or mechanism proposed, for this coupling. Here I report calculations of cluster charge distribution upon electron addition, revealing that the added negative charge is on the S atoms of FeMo-co, which thereby become more basic, and able to trigger proton transfer from H3O+ waiting at the near end of the proton wire. This mechanism is supported by calculations of the dynamics of the proton transfer step, in which the barrier is reduced by ca. 3.5 kcal mol-1 and the product stabilised by ca. 7 kcal mol-1 upon electron addition. H tunneling is probable in this step. In nitrogenase it is electron transfer that triggers proton transfer.

The E3 state of FeMoco: one hydride, two hydrides or dihydrogen?

Hydrides are present in the reduced states of the iron-molybdenum cofactor (FeMoco) of Mo nitrogenase and are believed to play a key mechanistic role in the dinitrogen reduction reaction catalyzed by the enzyme. Two hydrides are present in the E4 state according to 1H ENDOR and there is likely a single hydride in the E2 redox state. The 2-hydride E4 state has been experimentally observed to bind N2 and it has been speculated that E3 may bind N2 as well. However, the E3 state has not been directly observed and very little is known about its molecular and electronic structure or reactivity. In recent computational studies, we have explored the energy surfaces of the E2 and E4 by QM/MM modelling, and found that the most stable hydride isomers contain bridging or partially bridging hydrides with an open protonated belt sulfide-bridge. In this work we systematically explore the energy surface of the E3 redox state, comparing single hydride and two-hydride isomers with varying coordination and bridging vs. terminal sulfhydryl groups. We also include a model featuring a triply protonated carbide. The results are only mildly dependent on the QM-region size. The three most stable E3 isomers at the r2SCAN level of theory have in common: an open belt sulfide-bridge (terminal sulfhydryl group on Fe6) and either 2 bridging hydrides (between Fe2 and Fe6), 1 bridging-1-terminal hydride (around Fe2 and Fe6) or a dihydrogen ligand bound at the Fe2 site. Analyzing the functional dependency of the results, we find that functionals previously found to predict accurate structures of spin-coupled Fe/Mo dimers and FeMoco (TPSSh, B97-D3, r2SCAN, and B3LYP*) are in generally good agreement about the stability of these 3 E3 isomers. However, B3LYP*, similar to its parent B3LYP method, predicts a triply protonated carbide isomer as the most stable isomer, an unlikely scenario in view of the lack of experimental evidence for carbide protonation occurring in reduced FeMoco states. Distinguishing further between the 3 hydride isomers is difficult and this flexible coordination nature of hydrides suggests that multiple hydride isomers could be present during experimental conditions. N2 binding was explored and resulted in geometries with 2 bridging hydrides and N2 bound to either Fe2 or Fe6 with a local low-spin state on the Fe. N2 binding is predicted to be mildly endothermic, similar to the E2 state, and it seems unlikely that the E3 state is capable of binding N2.

How Protons Move in Enzymes─The Case of Nitrogenase

When moving protons in enzymes, water molecules are often used as intermediates. The water molecules used are not necessarily seen in the crystal structures if they move around at high rates. In a different situation, for metal containing cofactors in enzymes, it is sometimes necessary to move protons on the cofactor from the position they enter the cofactor to another position where the energy is lower. That is, for example, the situation in nitrogenase. In recent studies on that enzyme, prohibitively high barriers were sometimes found for transferring protons, and that was used as a strong argument against mechanisms where a sulfide is lost in the mechanism. A high barrier could be due to nonoptimal distances and angles at the transition state. In the present study, possibilities are investigated to use water molecules to reduce these barriers. The study is very general and could have been done for many other enzymes. The effect of water was found to be very large in the case of nitrogenase with a lowering of one barrier from 15.6 kcal/mol down to essentially zero. It is concluded that the effect of water molecules must be taken into account for meaningful results.

Biological nitrogen fixation in theory, practice, and reality: a perspective on the molybdenum nitrogenase system

Nitrogenase is the sole enzyme responsible for the ATP-dependent conversion of atmospheric dinitrogen into the bioavailable form of ammonia (NH₃ ), making this protein essential for the maintenance of the nitrogen cycle and thus life itself. Despite the widespread use of the Haber-Bosch process to industrially produce NH₃ , biological nitrogen fixation still accounts for half of the bioavailable nitrogen on Earth. An important feature of nitrogenase is that it operates under physiological conditions, where the equilibrium strongly favours ammonia production. This biological, multielectron reduction is a complex catalytic reaction that has perplexed scientists for decades. In this review, we explore the current understanding of the molybdenum nitrogenase system based on experimental and computational research, as well as the limitations of the crystallographic, spectroscopic, and computational techniques employed. Finally, essential outstanding questions regarding the nitrogenase system will be highlighted alongside suggestions for future experimental and computational work to elucidate this essential yet elusive process.

Proton Transfer Pathways in Nitrogenase with and without Dissociated S2B

Nitrogenase is the only enzyme that can convert N₂ to NH₃ . Crystallographic structures have indicated that one of the sulfide ligands of the active-site FeMo cluster, S2B, can be replaced by an inhibitor, like CO and OH^- , and it has been suggested that it may be displaced also during the normal reaction. We have investigated possible proton transfer pathways within the FeMo cluster during the conversion of N₂ H₂ to two molecules of NH₃ , assuming that the protons enter the cluster at the S3B, S4B or S5A sulfide ions and are then transferred to the substrate. We use combined quantum mechanical and molecular mechanical (QM/MM) calculations with the TPSS and B3LYP functionals. The calculations indicate that the barriers for these reactions are reasonable if the S2B ligand remains bound to the cluster, but they become prohibitively high if S2B has dissociated. This suggests that it is unlikely that S2B reversibly dissociates during the normal reaction cycle.

Calculating the chemical mechanism of nitrogenase: new working hypotheses

The enzyme nitrogenase converts N₂ to NH₃ with stoichiometry N₂ + 8H⁺ + 8e^- → 2NH₃ + H₂. The mechanism is chemically complex with multiple steps that must be consistent with much accumulated experimental information, including exchange of H₂ and N₂ and the N₂-dependent hydrogenation of D₂ to HD. Previous investigations have developed a collection of working hypotheses that guide ongoing density functional investigations of mechanistic steps and sequences. These include (i) hypotheses about the serial provision of protons and their conversion to H atoms bonded to S and Fe atoms of the FeMo-co catalytic site, (ii) the migration of H atoms over the surface of FeMo-co, (iii) the roles of His195, (iv) identification of three protein channels, one for the ingress of N₂, a separate pathway for the passage of exogenous H₂ (D₂) and product H₂ (HD), and a hydrophilic pathway for egress of product NH₃. Two additional working hypotheses are described in this paper. N₂ passing along the N₂ channel approaches and binds end-on to the exo coordination position of Fe2, with favourable energetics when FeMo-co is pre-hydrogenated. This exo-Fe2-N₂ is apparently not reduced but has a promotional role by expanding the reaction zone. A second N₂ can enter via the N₂ ingress channel and bind at the endo-Fe6 position, where it is surrounded by H atom donors suitable for the N₂ → NH₃ conversion. It is proposed that this endo-Fe6 position is also the binding site for H₂ (generated or exogenous), accounting for the competitive inhibition of N₂ reduction by H₂. The HD reaction occurs at the endo-Fe6 site, promoted by N₂ at the exo-Fe2 site. The second hypothesis concerns the most stable electronic states of FeMo-co with ligands bound at Fe2 and Fe6, and provides a protocol for management of electronic states in mechanism calculations.

Thermodynamically Favourable States in the Reaction of Nitrogenase without Dissociation of any Sulfide Ligand

We have used combined quantum mechanical and molecular mechanical (QM/MM) calculations to study the reaction mechanism of nitrogenase, assuming that none of the sulfide ligands dissociates. To avoid the problem that there is no consensus regarding the structure and protonation of the E₄ state, we start from a state where N₂ is bound to the cluster and is protonated to N₂H₂, after dissociation of H₂. We show that the reaction follows an alternating mechanism with HNNH (possibly protonated to HNNH₂) and H₂NNH₂ as intermediates and the two NH₃ products dissociate at the E₇ and E₈ levels. For all intermediates, coordination to Fe6 is preferred, but for the E₄ and E₈ intermediates, binding to Fe2 is competitive. For the E₄, E₅ and E₇ intermediates we find that the substrate may abstract a proton from the hydroxy group of the homocitrate ligand of the FeMo cluster, thereby forming HNNH₂, H₂NNH₂ and NH₃ intermediates. This may explain why homocitrate is a mandatory component of nitrogenase. All steps in the suggested reaction mechanism are thermodynamically favourable compared to protonation of the nearby His‐195 group and in all cases, protonation of the NE2 atom of the latter group is preferred.

Structures and reaction dynamics of N2 and H2 binding at FeMo-co, the active site of nitrogenase

The chemical reactions occurring at the Fe₇MoS₉C(homocitrate) cluster, FeMo-co, the active site of the enzyme nitrogenase (N₂ → NH₃), are enigmatic. Experimental information collected over a long period reveals aspects of the roles of N₂ and H₂, each with more than one type of reactivity. This paper reports investigations of the binding of H₂ and N₂ at intact FeMo-co, using density functional simulations of a large 486 atom relevant portion of the protein, resulting in 27 new structures containing H₂ and/or N₂ bound at the exo and endo coordination sites of the participating Fe atoms, Fe2 and Fe6. Binding energies and transition states for association/dissociation are determined, and trajectories for the approach, binding and separation of H₂/N₂ are described, including diffusion of these small molecules through proximal protein. Influences of surrounding amino acids are identified. FeMo-co deforms geometrically when binding H₂ or N₂, and a procedure for calculating the energy cost involved, the adaptation energy, is introduced here. Adaptation energies, which range from 7 to 36 kcal mol^-1 for the reported structures, are influenced by the protonation state of the His195 side chain. Seven N₂ structures and three H₂ structures have negative binding free energies, which include the estimated entropy penalties for binding of N₂, H₂ from proximal protein. These favoured structures have N₂ bound end-on at exo-Fe2, exo-Fe6 and endo-Fe2 positions of FeMo-co, and H₂ bound at the endo-Fe2 position. Various postulated structures with N₂ bridging Fe2 and Fe6 revert to end-on-N₂ at endo positions. The structures are also assessed via the calculated potential energy barriers for association and dissociation. Barriers to the binding of H₂ range from 1 to 20 kcal mol^-1 and barriers to dissociation of H₂ range from 3 to 18 kcal mol^-1. Barriers to the binding of N₂, in either side-on or end-on mode, range from 2 to 18 kcal mol^-1, while dissociation of bound N₂ encounters barriers of 3 to 8 kcal mol^-1 for side-on bonding and 7 to 18 kcal mol^-1 for end-on bonding. These results allow formulation of mechanisms for the H₂/N₂ exchange reaction, and three feasible mechanisms for associative exchange and three for dissociative exchange are identified. Consistent electronic structures and potential energy surfaces are maintained throughout. Changes in the spin populations of Fe2 and Fe6 connected with cluster deformation and with metal-ligand bond formation are identified.

Resolving the structure of the E1 state of Mo nitrogenase through Mo and Fe K-edge EXAFS and QM/MM calculations

Biological nitrogen fixation is predominately accomplished through Mo nitrogenase, which utilizes a complex MoFe7S9C catalytic cluster to reduce N2 to NH3. This cluster requires the accumulation of three to four reducing equivalents prior to binding N2; however, despite decades of research, the intermediate states formed prior to N2 binding are still poorly understood. Herein, we use Mo and Fe K-edge X-ray absorption spectroscopy and QM/MM calculations to investigate the nature of the E1 state, which is formed following the addition of the first reducing equivalent to Mo nitrogenase. By analyzing the extended X-ray absorption fine structure (EXAFS) region, we provide structural insight into the changes that occur in the metal clusters of the protein when forming the E1 state, and use these metrics to assess a variety of possible models of the E1 state. The combination of our experimental and theoretical results supports that formation of E1 involves an Fe-centered reduction combined with the protonation of a belt-sulfide of the cluster. Hence, these results provide critical experiment and computational insight into the mechanism of this important enzyme.

Survey of the Geometric and Electronic Structures of the Key Hydrogenated Forms of FeMo-co, the Active Site of the Enzyme Nitrogenase: Principles of the Mechanistically Significant Coordination Chemistry

The enzyme nitrogenase naturally hydrogenates N2 to NH3, achieved through the accumulation of H atoms on FeMo-co, the Fe7MoS9C(homocitrate) cluster that is the catalytically active site. Four intermediates, E1H1, E2H2, E3H3, and E4H4, carry these hydrogen atoms. I report density functional calculations of the numerous possibilities for the geometric and electronic structures of these poly-hydrogenated forms of FeMo-co. This survey involves more than 100 structures, including those with bound H2, and assesses their relative energies and most likely electronic states. Twelve locations for bound H atoms in the active domain of FeMo-co, including Fe–H–Fe and Fe–H–S bridges, are studied. A significant result is that transverse Fe–H–Fe bridges (transverse to the pseudo-threefold axis of FeMo-co and shared with triply-bridging S) are not possible geometrically unless the S is hydrogenated to become doubly-bridging. The favourable Fe–H–Fe bridges are shared with doubly-bridging S. ENDOR data for an E4H4 intermediate trapped at low temperature, and interpretations in terms of the geometrical and electronic structure of E4H4, are assessed in conjunction with the calculated possibilities. The results reported here yield a set of 24 principles for the mechanistically significant coordination chemistry of H and H2 on FeMo-co, in the stages prior to N2 binding.

How feasible is the reversible S-dissociation mechanism for the activation of FeMo-co, the catalytic site of nitrogenase?

The active site of the enzyme nitrogenase (N₂→ NH₃) is a Fe₇MoS₉C cluster that contains three doubly-bridging μ-S atoms around a central belt. A vanadium nitrogenase variant has a slightly different cluster, containing two μ-S atoms. Recent crystal structures have revealed substitution of one μ-S (S2B, bridging Fe2 and Fe6), by CO in Mo-nitrogenase and an uncertain light atom in V-nitrogenase. These systems retained catalytic activity, and were able to recover the lost μ-S atom. Electron density attributed to the dissociated S is displaced by 7 Å in the crystal structure of the non-standard V-protein. The hypothesis arising from these observations is that the chemical mechanism of nitrogenase involves reversible dissociation of S2B, leaving Fe2 and Fe6 seriously under-coordinated and reactive in trapping N₂ and binding reaction intermediates. Accumulated experimental evidence points to the Fe2-S2B-Fe6 domain as the centre of catalytic hydrogenation of N₂. Using DFT simulations of a large model (>488 atoms) containing all relevant surrounding protein residues, I have investigated the chemical steps that could allow dissociation of S2B. The participation of H atoms is crucial, as is involvement of the nearby side chain of His195 that can function as proton donor to S2B and hydrogen-bonding supporter of displaced S2B. A significant result is that after ingress and binding of N₂ at Fe2 the breaking of the Fe2-S2B bond can be strongly exergonic with negligible kinetic barrier. Subsequent extension of the Fe6-S2B bond and dissociation as H₂S (or SH^-) is endergonic by 20-25 kcal mol^-1, partly because the separating H₂S is restricted by surrounding amino-acids. I present a number of reaction sequences and energy landscapes, and derive thirteen chemical principles relevant to the postulated S-dissociation mechanism. A key conclusion is that unhooking of S2BH or S2BH₂ from Fe2 is favourable, likely, and propitious for subsequent H transfer to bound N₂ or reaction intermediates. The space between Fe2 and Fe6 supports two bridging ligands, and another H atom on Fe6 can move without kinetic barrier to occupy the bridging position vacated by S2B.