Air-abrasion using new silica-alumina powders containing different silica concentrations: Effect on the microstructural characteristics and fatigue behavior of a Y-TZP ceramic

Effect of different surface treatments on the bonding potential and physical and mechanical properties of ultratranslucent zirconia

STATEMENT OF PROBLEM

Studies to determine a suitable surface treatment that improves bonding without compromising the strength or translucency of ultratranslucent zirconia are scarce.

PURPOSE

The purpose of this in vitro study was to evaluate the effect of different surface treatments on translucency, surface topography, phase transformation, biaxial flexural strength, bond strength, and durability.

MATERIAL AND METHODS

A total of 169 ultratranslucent zirconia disks were randomly divided into 4 groups according to the surface treatment applied: airborne-particle abrasion (APA) (n=46), tribochemical silica airborne-particle abrasion (TS) (n=46), nonthermal oxygen plasma (NTP) (n=46), and no treatment, control (C) (n=31). The translucency parameter (ΔTP00) was evaluated with a spectrophotometer (n=15), phase transformation was assessed with an X-ray diffractometer (n=5), surface topography was evaluated with a scanning electron microscope (SEM) (n=3), and biaxial flexural strength (BFS) was tested with a universal testing machine (n=15). For the microshear bond strength (μSBS) test, 40 composite resin specimens were attached to 8 disks and tested with a universal testing machine; 20 specimens were tested after 24 hours, and 20 specimens after hydrothermal aging in a thermocycler (TC). The data were analyzed with ANOVA followed by the Tukey post hoc test (α=.05). Weibull analysis was performed for the flexural strength and μSBS results.

RESULTS

Significant ΔTP00 differences were found among all groups and were highest for the APA group (7.33) and lowest for the NTP group (4.79). The NTP group had a significantly higher monoclinic weight fraction value (4.54%) than other groups. The NTP group had significantly higher BFS (581.31) than other groups, while the APA group showed significantly lower values than other groups (340.43). The APA group had significantly higher μSBS values after 24 hours (13.51 MPa) and after TC (13.68 MPa) than the other groups (P<.05).

CONCLUSIONS

Although APA and TS are effective techniques for improving resin-zirconia bonding, they result in significantly higher deterioration of translucency and strength. NTP significantly improved the BFS of zirconia; however, it showed lower bond strength values than other methods.

A brief review on fatigue test of ceramic and some related matters in Dentistry

The characteristics of dental ceramics have been extensively studied over the years to provide highly qualified materials for use in prosthetic restorations. The ability to adhere to dental substrates, outstanding aesthetics (translucency, color, and substrate masking ability) and improved mechanical properties provide these materials with optical features and high strength to withstand masticatory stimuli. Different classifications are adopted, and it is generally considered that glass-ceramics have better optical characteristics due to the high glass content, and polycrystalline ceramics have superior strength favored by their densified and organized crystals, hampering crack growth. This knowledge was largely built-up during years of scientific research through different testing methodologies, but mainly employing static loads. It is important to not only take into account the intensity of loads that these materials will be exposed to, but also the effect of the intermittence of cyclic load application leading to mechanical fatigue and the influence of factors related to the crack origin and their propagation under this condition. Furthermore, the bonding surface of ceramic restorations requires surface treatments that improve the bond strength to luting agents; however, these treatments require caution because of their potential to produce defects and affect the structural behavior. Moreover, ceramic restorations often require internal adjustments for proper seating or external adjustments for fitting the occlusal contact with the antagonist. In this sense, finishing/polishing protocols may alter the defect population, as luting agents may also interact by filling in the superficial defects on the restoration intaglio surface. Thus, the balance among all these factors will define the performance of a restorative setup, as well as the posterior exposure to the humid environment and the masticatory stimuli (cyclical loading), which may favor developing slow and subcritical growth of cracks in ceramic materials and the degradation of the bond interface. Therefore, it is essential that the concepts which explain the fatigue mechanism are understood, as well as the crack propagation and failure patterns of restorative ceramic materials.

In-lab simulation of CAD/CAM grinding and intaglio surface treatments of 4YSZ monolithic restorations: Effect on its load-bearing capacity under fatigue

OBJECTIVES

To evaluate the effect of in-lab simulation of CAD/CAM grinding and intaglio surface treatments on the surface characteristics (topography and roughness) and fatigue behavior of adhesively luted 4YSZ simplified restorations.

METHODS

Ceramic discs (Ø = 10 mm, thickness = 1 mm) were randomly allocated into 6 groups considering: "In-lab simulation of CAD/CAM grinding" (ground or polished) and "intaglio surface treatments": Ctrl (without surface treatment), AlOx (aluminum oxide air abrasion) or GLZ (glaze spray application). The surface roughness of all samples was measured, the treated discs received a ceramic primer, were luted with resin cement onto a dentin analogue material (woven glass-reinforced epoxy resin) and tested under a cyclic fatigue test (step-stress approach, n = 15; 1.4 Hz, 10,000 cycles/step, step-size of 100N starting at 200N until failure). A complementary analysis was performed to corroborate the findings in the fatigue test that the glaze fill defects increase the mechanical properties of the ceramic. To do so, bars (n= 10; 1.0 × 1.0 × 12 mm; considering the groups: N-ID: non-indented; ID: indented; ID-GLZ: indented plus glaze spray application) were indented in a vickers hardness tester to produce a crack pattern, treated with glaze or not, and then submitted to flexural strength tests (FS). Fractographic and topographic analysis were performed.

RESULTS

In-lab simulation of CAD/CAM grinding decreased the fatigue failure load of the 4YSZ ceramic when comparing polished and ground groups, regardless of surface treatment. GLZ induced better fatigue performance compared to the air abrasion, regardless of the grinding condition (ground or polished surface). The results of the flexural strength test corroborated the findings in the fatigue test, as the ID-GLZ group presented superior FS than the ID group, however both had inferior FS than N-ID. There is an inverse association between roughness and fatigue failure load, as the higher the surface roughness, the lower the fatigue failure load. Failures in the fatigue and flexural strength tests started from the face subjected to tensile stresses.

CONCLUSION

In-lab simulation of CAD/CAM grinding had a detrimental effect on the fatigue behavior of 4YSZ and glaze spray induced better 4YSZ performance compared to the air abrasion. The intaglio surface treatments differently influenced the 4YSZ fatigue performance, however, only glaze spray can reverse the damage caused by the grinding.

Surface treatments and its effects on the fatigue behavior of a 5% mol yttria partially stabilized zirconia material

This study evaluated the effect of distinct surface treatments on the fatigue behavior (biaxial flexural fatigue testing) and surface characteristics (topography and roughness) of a 5% mol yttria partially stabilized zirconia ceramic (5Y-PSZ). Disc-shaped specimens of 5Y-PSZ (IPS e.max ZirCAD MT Multi) were manufactured (ISO 6872-2015) and allocated into six groups (n = 15) considering the following surface treatments: Ctrl - no-treatment; GLZ - low-fusing porcelain glaze application; SNF - 5 nm SiO₂ nanofilm; AlOx - aluminum oxide particle air-abrasion; SiC - silica-coated aluminum oxide particles (silica-coating); and 7%Si - 7% silica-coated aluminum oxide particles (silica-coating). The biaxial flexural fatigue tests were performed by the step-stress method (20Hz for 10,000 cycles) with a step increment of 50N starting at 100N and proceeding until failure detection. The samples were tested with the treated surface facing down (tensile stress side). Topography, fractography, roughness, and phase content assessments of treated specimens were performed. GLZ group presented the highest fatigue behavior, while AlOx presented the lowest performance, and was only similar to SiC and 7%Si. Ctrl and SNF presented intermediary fatigue behavior, and were also similar to SiC and 7%Si. GLZ promoted a rougher surface, Ctrl and SNF had the lowest roughness, while the air-abrasion groups presented intermediary roughness. No m-phase content was detected (only t and c phases were detected). In conclusion, the application of a thin-layer of low-fusing porcelain glaze, the deposition of silica nanofilms and the air-abrasion with silica-coated alumina particles had no detrimental effect on the fatigue behavior of the 5Y-PSZ, while the air-abrasion with alumina particles damaged the fatigue outcomes.

Fatigue performance of fully-stabilized zirconia polycrystals monolithic restorations: The effects of surface treatments at the bonding surface

This study evaluated the distinct conditioning effect of the intaglio surface of bonded fully-stabilized zirconia (FSZ) simplified restorations on the mechanical fatigue behavior of the set prior to and after aging. Ceramic disc shaped specimens (Ø= 10 mm and 1 mm thick) were randomly allocated into 14 groups considering: "surface treatments" (Ctrl: no-treatment; PM: universal primer; GLZ: low-fusing porcelain glaze; SNF: 5 nm SiO₂ nanofilm deposition; AlOx: air-abrasion with aluminum oxide; SiC: air-abrasion with silica-coated aluminum oxide; 7%Si: air-abrasion with 7% silica-coated aluminum oxide); and "aging" (baseline: 24 h at 37 °C in water; or aged: 90 days at 37 °C in water + 12,000 thermal cycles). The discs were treated, luted with resin cement onto the dentin analog, subjected to aging or not, and then tested under a step-stress fatigue test at 20 Hz, 10,000 cycles/step, step-size of 100N starting at 200N, and proceeding until failure detection. Fractographic, topographic, surface roughness, contact angle, and atomic force microscopy analyzes were performed. The surface treatments at baseline led to statistically similar fatigue failure loads (953N-1313N), except for GLZ (1313N), which was significantly higher than 7%Si (953 N). Meanwhile, Ctrl had 40% pre-test failures (debonding) after aging, and therefore the worst fatigue performance (notable decrease in fatigue results), while all the other groups presented superior and statistically similar fatigue behavior (973-1271N). In fact, when considering baseline Vs aging conditions, stable fatigue results could only be noted when using surface treatments. In conclusion, internal surface treatments of FSZ ceramic restorations are mandatory for fatigue behavior stability after aging the restorative set, while non-treatment induced unstable results.

Grinding the intaglio surface of yttria partially- and fully-stabilized zirconia polycrystals restorations: Effect on their fatigue behavior

This study evaluated the effects of diamond bur grinding the intaglio surface of second (yttria partially-stabilized zirconia polycrystals, PSZ) and third-generation zirconia (fully-stabilized zirconia polycrystals, FSZ) adhesively cemented to dentin analogue substrate on the fatigue failure load, cycle number until failure, surface micromorphology and phase transformation. Disc-shaped specimens were produced from second (Katana ML-HT, Kuraray) and third-generation zirconia (Katana STML, Kuraray) and randomly allocated (n = 15) into two groups according to the intaglio surface treatment: Control - Ctrl (without grinding); Grinding - Gr (grinding at the center of the intaglio surface). The ceramic discs were adhesively cemented (Multilink Automix System) onto dentin analogue discs. Fatigue tests were executed by the step-stress method. The obtained data were analyzed by Kaplan Meier and Mantel-Cox tests. In addition, surface topography, roughness, phase transformation and fractography analyses were performed. SEM analysis showed that grinding increased the surface roughness and introduced defects in zirconia from both generations. Grinding increased the fatigue failure load, number of cycles to failure and survival rates of the second-generation zirconia statistically (control: 1373.33 N < grinding: 1600 N), while these same outcomes were reduced by grinding for the third-generation zirconia significantly (control: 766.67 N > grinding: 620 N). Thus, clinical adjustments with diamond burs damage the fatigue behavior of adhesively cemented third-generation zirconia.