Articulation of an alumina-zirconia composite ceramic against living cartilage – An in vitro wear test

Comparison of wear on articular cartilage by titanium alloy, ultra-high-molecular-weight polyethylene, and carbon fibre reinforced polyether-ether-ketone: A pilot study

Artificial implant materials may articulate against native articular cartilage in certain clinical scenarios and the selection of an implant material that results in the least wear on articular cartilage is preferred to maintain normal joint architecture and function. This project compared the wear on porcine femoral condyles induced by articulation against porcine patellae, titanium alloy (Ti6Al4V), ultra high molecular weight polyethylene (UHMWPE), and carbon fibre reinforced polyether-ether-ketone (CFR-PEEK) through an ex vivo experimental setup. A sinusoidal compressive load of 30-160 N, representing an approximate joint pressure of 0.19-1 MPa at a frequency of 3 Hz coupled with a rotational displacement of +/- 10⁰ at 3 Hz was used to simulate physiological joint motion. Wear was characterized via gross examination and histologically using the OARSI scoring system after 43,200 cycles. CFR-PEEK resulted in the most significant wear on articular cartilage compared to titanium alloy and UHMWPE whereas titanium alloy and UHMWPE resulted in similar levels of wear. All materials caused more wear compared to cartilage-on-cartilage testing. The wear mechanism was characterized by progressive loss of proteoglycan content in cartilage in histology samples.

Effect of Mechanical Mincing on Minimally Manipulated Articular Cartilage for Surgical Transplantation

BACKGROUND

Point-of-care treatment options for medium to large symptomatic articular cartilage defects are limited. Minced cartilage implantation is an encouraging single-stage option, providing fresh viable autologous tissue with minimal morbidity and cost.

PURPOSE

To determine the histological properties of mechanically minced versus minimally manipulated articular cartilage.

STUDY DESIGN

Controlled laboratory study.

METHODS

Remnant articular cartilage was collected from fresh femoral condylar allografts. Cartilage samples were divided into 4 groups: cartilage explants with or without fibrin glue and mechanically minced cartilage with or without fibrin glue. Samples were cultured for 42 days. Chondrocyte viability was assessed using live/dead assay. Cellular migration and outgrowth were monitored using bright-field microscopy. Extracellular matrix deposition was assessed via histological staining. Proteoglycan content and synthesis were assessed using dimethylmethylene blue assay and radiolabeled 35S-sulfate, respectively. Type II collagen (COL2A1) gene expression was analyzed via polymerase chain reaction.

RESULTS

The mean viability of minced cartilage particles (34% ± 14%) was not significantly reduced compared with baseline (46% ± 13%) on day 0 (P = .90). After culture, no significant difference in the percentage of live cells was appreciated between mechanically minced (58% ± 23%) and explant (73% ± 14%) cartilage in the presence of fibrin glue (P = .52). The addition of fibrin glue did not significantly affect the viability of cartilage samples. The qualitative assessment revealed comparable cellular migration and outgrowth between groups. Proteoglycan synthesis was not significantly different between groups. Histological analysis findings were positive for COL2A1 in all groups, and matrix formation was appreciated in all groups. COL2A1 expression in minced cartilage (1.72 ± 1.88) was significantly higher than in explant cartilage (0.15 ± 0.07) in the presence of fibrin glue (P = .01).

CONCLUSION

Mechanically minced articular cartilage remained viable after 42 days of culture in vitro and was comparable with cartilage explants with regard to cellular migration, outgrowth, and extracellular matrix synthesis.

CLINICAL RELEVANCE

Mechanically minced articular cartilage is an encouraging intervention for the treatment of symptomatic cartilage defects. Further translational work is warranted to determine the viability of minced cartilage implantation as a single-stage therapeutic intervention in vivo.

A review of advances in tribology in 2020–2021

Around 1,000 peer-reviewed papers were selected from 3,450 articles published during 2020–2021, and reviewed as the representative advances in tribology research worldwide. The survey highlights the development in lubrication, wear and surface engineering, biotribology, high temperature tribology, and computational tribology, providing a show window of the achievements of recent fundamental and application researches in the field of tribology.

Bio-tribological behavior of articular cartilage based on biological morphology

Artificial hemiarthroplasty is one of the effective methods for the treatment of hip joint diseases, but the wear failure of the interface between the hemi hip joint material and articular cartilage restricts the life of the prosthesis. Therefore, it is important to explore the damage mechanism between the interfaces to prolong the life of the prosthesis and improve the life quality of the prosthesis replacement. In this paper, the creep and bio-tribological properties of cartilage against PEEK, CoCrMo alloy, and ceramic were studied, and the tribological differences between "hard-soft" and "soft-soft" contact were analyzed based on biomorphology. The results showed that with the increase of time in vitro, the thickness of the cartilage membrane decreased, the surface damage was aggravated, and the anti-creep ability of cartilage was weakened. Second, the creep resistance of the soft-soft contact pair was better than that of the hard-soft contact pair. Also, the greater the load and the longer the wear time, the more serious the cartilage damage. Among the three friction pairs, the cartilage in PEEK/articular cartilage was the least damaged, followed by CoCrMo alloy/articular cartilage, and the most damage was found in ceramic/articular, indicating that the soft-soft friction pair inflicted the least damage to the cartilage.

New Perspectives on Zirconia Composites as Biomaterials

Zirconia–alumina composites couple the high toughness of zirconia with the peculiar properties of alumina, i.e., hardness, wear, and chemical resistance, so they are considered promising materials for orthopedic and dental implants. The design of high performance zirconia composites needs to consider different aspects, such as the type and amount of stabilizer and the sintering process, that affect the mechanics of toughening and, hence, the mechanical properties. In this study, several stabilizers (Y2O3, CuO, Ta2O5, and CeO2) were tested together with different sintering processes to analyze the in situ toughening mechanism induced by the tetragonal–monoclinic (t–m) transformation of zirconia. One of the most important outcomes is the comprehension of the opposite effect played by the grain size and the tetragonality of the zirconia lattice on mechanical properties, such as fracture toughness and bending strength. These results allow for the design of materials with customized properties and open new perspectives for the development of high-performance zirconia composites for orthopedic implants with high hydrothermal resistance. Moreover, a near-net shape forming process based on the additive manufacturing technology of digital light processing (DLP) was also studied to produce ceramic dental implants with a new type of resin–ceramic powder mixture. This represents a new frontier in the development of zirconia composites thanks to the possibility to obtain a customized component with limited consumption of material and reduced machining costs.

Transient stiffening of cartilage during joint articulation: A microindentation study

As a mechanoactive tissue, articular cartilage undergoes compression and shear on a daily basis. With the advent of high resolution and sensitive mechanical testing methods, such as micro- and nanoindentation, it has become possible to assess changes in small-scale mechanical properties due to compression and shear of the tissue. However, investigations on the changes of these properties before and after joint articulation have been limited. To simulate articular loading of cartilage in the context of human gait, a previously developed bioreactor system was used. Immediately after bioreactor testing, the stiffness was measured using microindentation. Specifically, we investigated whether the mechanical response of the tissue was transient or permanent, dependent on counterface material, and an effect limited to the superficial zone of cartilage. We found that cartilage surface stiffness increases immediately after articular loading and returns to baseline values within 3 hr. Cartilage-on-cartilage stiffening was found to be higher compared to both alumina- and cobalt chromium-on-cartilage stiffening, which were not significantly different from each other. This stiffening response was found to be unique to the superficial zone, as articular loading on cartilage with the superficial zone removed showed no changes in stiffness. The findings of this study suggest that the cartilage superficial zone may adapt its stiffness as a response to articular loading. As the superficial zone is often compromised during the course of osteoarthritic disease, this finding is of clinical relevance, suggesting that the load-bearing function deteriorates over time.

Preclinical evaluation of a mini-arthroplasty implant based on polyetheretherketone and Ti6AI4V for treatment of a focal osteochondral defect in the femoral head of the hip

A mini or partial arthroplasty may offer the advantages of reduced pain, shorter hospital stay, and increased range of motion, which are beneficial for the treatment of large-sized focal osteochondral defects. We aimed to evaluate the in vivo histologic response and function of our nonresorbable, composite structure implant, developed using polyetheretherketone (PEEK) and Ti6AI4V alloy, as a treatment for full-thickness osteochondral defects in the femoral head of the hip using a goat model. The gross and imaging appearance and histologic results were compared to those of a similar size cobalt-chromium-molybdenum (CoCrMo) alloy implant placed in a defect in the femoral head and evaluated up to 12 weeks. The X radiographs showed that there was no evidence of loosening of the implants for both the PEEK-Ti6AI4V and CoCrMo groups. Magnetic resonance imaging results showed no inflammatory signal findings in both PEEK-Ti6AI4V and CoCrMo implants. Macroscopically and histologically, there was lesser cartilage degeneration in the PEEK-Ti6AI4V implant than in the CoCrMo implant. The modified macroscopic articular evaluation score was lower in the PEEK-Ti6AI4V group than in the CoCrMo group (p < 0.05), and the histological score of the periprosthetic and acetabular cartilage was lower in the PEEK-Ti6AI4V group than in the CoCrMo group (P < 0.05). The micro-computed tomography results showed that the uncemented PEEK-Ti6AI4V implant has better osseointegration and higher bone-implant contact than the cemented CoCrMo implant. The peri-implant bone mass was higher in the PEEK-Ti6AI4V implant(p < 0.05). Meanwhile, the optical profile analytical results showed that the surface roughness of the cartilage in the acetabulum was higher in the CoCrMo group. In conclusion, the mini-arthroplasty implant based on PEEK-Ti6AI4V was superior to an identical CoCrMo alloy implant as a treatment for local osteochondral defect in the femoral head, owing to its in vivo cartilage protection and better osseointegration.