Titanium mesh-reinforced calcium sulfate for structural bone grafts

Personalized 3D printed bone scaffolds: A review

3D printed bone scaffolds have the potential to replace autografts and allografts because of advantages such as unlimited supply and the ability to tailor the scaffolds' biochemical, biological and biophysical properties. Significant progress has been made over the past decade in additive manufacturing techniques to 3D print bone grafts, but challenges remain in the lack of manufacturing techniques that can recapitulate both mechanical and biological functions of native bones. The purpose of this review is to outline the recent progress and challenges of engineering an ideal synthetic bone scaffold and to provide suggestions for overcoming these challenges through bioinspiration, high-resolution 3D printing, and advanced modeling techniques. The article provides a short overview of the progress in developing the 3D printed scaffolds for the repair and regeneration of critical size bone defects. STATEMENT OF SIGNIFICANCE: Treatment of critical size bone defects is still a tremendous clinical challenge. To address this challenge, diverse sets of advanced manufacturing approaches and materials have been developed for bone tissue scaffolds. 3D printing has sparked much interest because it provides a close control over the scaffold's internal architecture and in turn its mechanical and biological properties. This article provides a critical overview of the relationships between material compositions, printing techniques, and properties of the scaffolds and discusses the current technical challenges facing their successful translation to the clinic. Bioinspiration, high-resolution printing, and advanced modeling techniques are discussed as future directions to address the current challenges.

High porosity 3D printed titanium mesh allows better bone regeneration

BACKGROUND

Most patients with insufficient bone mass suffer from severe horizontal or vertical bone defects in oral implant surgery. The purpose of this study was to compare the bone regeneration effects of titanium meshes with different porosity in the treatment of bone defects.

METHODS

Nine beagle dogs were equally divided into three groups based on execution time. Three months after the extraction of the first to fourth premolars of the mandible, three bone defects were randomly made in the mandible. Bone particles and three kinds of three-dimensional (3D) printed titanium nets with different porosities (low porosity group (LP), 55%; medium porosity group (MP), 62%; and high porosity group (HP), 68%) were replanted in situ. The beagles were killed 4, 8, and 12 weeks after surgery. Formalin-fixed specimens were embedded in acrylic resin. The specimens were stained with micro-CT, basic fuchsin staining, and toluidine blue staining.

RESULTS

Micro-CT analysis showed that the trabecular thickness, trabecular number, and bone volume fraction of the HP group were higher than those of the other two groups. Moreover, the trabecular separation of the HP group decreased slightly and was lower than that of the MP and LP groups. Histological staining analysis showed that the trabecular number in the HP group was higher than in the other two groups at 8 and 12 weeks, and the bone volume fraction of the HP was higher than that in the other two groups at 12 weeks. Moreover, the trabecular thickness of the MP was higher than that of the LP group at 12 weeks and the trabecular separation was lower in the HP group at 4 and 8 weeks. The differences were statistically significant (p < 0.05).

CONCLUSION

A 3D printed titanium mesh with HP in a certain range may have more advantages than a titanium mesh with LP in repairing large bone defects.

Successful management of a rare radius schwannoma mimicking malignant bone tumors: A case report and literature review

Background

Schwannomas are benign tumors originating from Schwann cells, frequently occurring in the spinal cord and peripheral nerves. Intraosseous schwannomas, a rare subset, account for approximately 0.2% of schwannomas. Intraosseous schwannomas commonly impinge the mandible, followed by the sacrum and the spine. By far, only three cases of radius intraosseous schwannomas have been reported in PubMed. The tumor was treated differently in all three cases, resulting in different outcomes.

Case presentation

A 29-year-old male construction engineer who complained of a painless mass on the radial aspect of the right forearm was diagnosed with an intraosseous schwannoma of the radius based on radiography, three-dimensional computed tomography reconstruction, magnetic resonance imaging, pathological examination, and immunohistochemistry. A different surgical approach was employed to reconstruct the radial graft defect using bone microrepair techniques, resulting in more reliable bone healing and early functional recovery. Meanwhile, no clinical and radiographic findings suggestive of recurrence were observed at the 12-month follow-up.

Conclusion

Vascularized bone flap transplantation combined with three-dimensional imaging reconstruction planning might yield better results for repairing small segmental bone defects of the radius caused by intraosseous schwannomas.

The Role of Substrate Topography and Stiffness on MSC Cells Functions: Key Material Properties for Biomimetic Bone Tissue Engineering

The hypothesis of the present research is that by altering the substrate topography and/or stiffness to make it biomimetic, we can modulate cells behavior. Substrates with similar surface chemistry and varying stiffnesses and topographies were prepared. Bulk PCL and CNTs-reinforced PCL composites were manufactured by solvent casting method and electrospinning and further processed to obtain tunable moduli of elasticity in the range of few MPa. To ensure the same chemical profile for the substrates, a protein coating was added. Substrate topography and properties were investigated. Further on, the feedback of Wharton’s Jelly Umbilical Cord Mesenchymal Stem Cells to substrates characteristics was investigated. Solvent casting scaffolds displayed superior mechanical properties compared to the corresponding electrospun films. However, the biomimetic fibrous texture of the electrospun substrates induced improved feedback of the cells with respect to their viability and proliferation. Cells’ adhesion and differentiation was remarkably pronounced on solvent casting substrates compared to the electrospun substrates. Soft substates improved cells multiplication and migration, while stiff substrates induced differentiation into bone cells. Aspects related to the key factors and the ideal properties of substrates and microenvironments were clarified, aiming towards the deep understanding of the required optimum biomimetic features of biomaterials.