Development and validation of a parametric human mandible model to determine internal stresses for the future design optimization of maxillofacial implants

Mechanical and modal analysis of different implant strategies for loss of three teeth with bone atrophy in the maxillary posterior region

PURPOSE

This study aimed to evaluate the stress distribution and secondary stability involved in five implant strategies, including implant-supported prostheses (ISP) and tooth-implant-supported prostheses (TISP), used for bone atrophy in the maxillary posterior region with teeth loss using finite element analysis, and to explore the more desirable implant methods.

METHODS

Five implant strategies were made to analyze and compare: M1, implant-supported prosthesis consisting of a short implant with a regular implant; M2, implant-supported prosthesis consisting of a tilted implant with a regular implant; M3, cantilever structure; M4, tooth-implant-supported prosthesis consisting of a short implant with a regular implant; M5, tooth-implant-supported prosthesis consisting of a regular implant, and M6, with only the natural teeth as a control group. Dynamic loading of the above models was performed in finite element analysis software to assess the stress distribution of the bone tissue and implants using the von Mise criterion. Finally, the secondary stability of different models was evaluated by modal analysis.

RESULTS

The maximum stress distribution in the cortical bone in M1(60 MPa) was smaller than that in M2(97 MPa) and M3(101 MPa), The first principal strain minimum was obtained in M2 (2271μ ε ). M4 (33 MPa, 10085 Hz) with the best mechanical properties and highest resonance frequency. But increased the loading on the natural teeth.

CONCLUSIONS

Short implants and tilted implants are both preferred implant strategies, if cantilever construction is necessary, a tooth-implant-supported prosthesis consisting of a short implant and a regular implant is recommended.

Development of a test bench for biomechanical simulation-a preliminary study of mandibular forces

Purpose: The aim of this study is to develop a test bench, which integrates different complexity levels and enables in that way a flexible and dynamic testing for mid and long term intervals as well as testing of maximum loads till implant failure of different osteosynthesis systems on the mandible. Material and Methods: For this purpose, an analysis of the state of the art regarding existing test benches was combined with interviews of clinical experts to acquire a list of requirements. Based on these requirements a design for a modular test bench was developed. During the implementation of the test stand, functional tests were continuously carried out and improvements made. Depending on the level of complexity, the test bench can be used either as an incorporated variant or as a standalone solution. In order to verify the performance and the degree of fulfilment of the requirements of these two variants of the test bench, preliminary studies were carried out for all levels of complexity. In these preliminary studies, commercially available osteosynthesis and reconstruction plates were investigated for their biomechanical behaviour and compared with data from the literature. Results: In total, fourteen test runs were performed for the different levels of complexity. Firstly, five test runs were executed to test the simplified load scenario in the incorporated variant of the test bench. High forces could be transmitted without failure of the miniplates. Secondly a quasi-static test scenario was examined using the incorporated variant with simplified load insertion. Five experiments with a number of cycles between 40,896 and 100,000 cycles were carried out. In one case the quasi-static testing resulted in a fracture of the tested reconstruction plate with a failure mode similar to the clinical observations of failure. The last four test runs were carried out using the standalone variant of the test bench simulating complex load patterns via the insertion of forces through imitated muscles. During the test runs joint forces were measured and the amplitude and vector of the resulting joint forces were calculated for both temporomandibular joints. Differences in the force transmission depending on the implant system in comparison to the zero sample could be observed. Conclusion: The presented modular test bench showed to be applicable for examination of the biomechanical behavior of the mandible. It is characterized by the adjustability of the complexity regarding the load patterns and enables the subsequent integration of further sensor technologies. Follow-up studies are necessary to further qualify and optimize the test bench.

Development and validation of a digital twin of the human lower jaw under impact loading by using non-linear finite element analyses

Mandibular fractures are one of the most frequently observed injuries within craniofacial region mostly due to tumor-related problems and traumatic events, often related to non-linear effects like impact loading. Therefore, a validated digital twin of the mandible is required to develop the best possible patient-specific treatment. However, there is a need to obtain a fully compatible numerical model that can reflect the patients' characteristics, be available and accessible quickly, require an acceptable level of modeling efforts and knowledge to provide accurate, robust and fast results at the same time under highly non-linear effects. In this study, a validated simulation methodology is suggested to develop a digital twin of mandible, capable of predicting the non-linear response of the biomechanical system under impact loading, which then can be utilized to design treatment strategies even for multiple fractures of the mandibular system. Using Computed Tomography data containing cranial (skull) images of a patient, a 3-dimensional mandibular model, which consists cortical and cancellous bones, disks and fossa is obtained with high accuracy that is compatible with anatomical boundaries. A Finite Element Model (FEM) of the biomechanical system is then developed for a three-level validation procedure including (A) modal analysis, (B) dynamic loading and (C) impact loading. For the modal analysis stage: Free-free vibration modes and frequencies of the system are validated against cadaver test results. For the dynamic loading stage: Two different regions of the mandible are loaded, and maximum stress levels of the system are validated against finite element analyses (FEA) results, where the first loading condition (i) transfers a 2000 N force acting on the symphysis region and, the second loading condition (ii) transfers a 2000 N force acting on the left body region. In both cases, equivalent muscle forces dependent on time are applied. For the impact loading stage: Thirteen different human mandibular models with various tooth deficiencies are used under the effects of traumatic impact forces that are generated by using an impact hammer with different initial velocities to transfer the impulse and momentum, where contact forces and fracture patterns are validated against cadaver tests. Five different anatomical regions are selected as the impact site. The results of the analyzes (modal, dynamic and impact) performed to validate the digital twin model are compared with the similar FEA and cadaver test results published in the literature and the results are found to be compatible. It has been evaluated that the digital twin model and numerical models are quite realistic and perform well in terms of predicting the biomechanical behavior of the mandible. The three-level validation methodology that is suggested in this research by utilizing non-linear FEA has provided a reliable road map to develop a digital twin of a biomechanical system with enough confidence that it can be utilized for similar structures to offer patient-specific treatments and can help develop custom or tailor-made implants or prosthesis for best compliance with the patient even considering the most catastrophic effects of impact related trauma.

Three-Dimensional Printing of Graphene Oxide/Poly-L-Lactic Acid Scaffolds Using Fischer-Koch Modeling

Accurately printing customizable scaffolds is a challenging task because of the complexity of bone tissue composition, organization, and mechanical behavior. Graphene oxide (GO) and poly-L-lactic acid (PLLA) have drawn attention in the field of bone regeneration. However, as far as we know, the Fischer-Koch model of the GO/PLLA association for three-dimensional (3D) printing was not previously reported. This study characterizes the properties of GO/PLLA-printed scaffolds in order to achieve reproducibility of the trabecula, from virtual planning to the printed piece, as well as its response to a cell viability assay. Fourier-transform infrared and Raman spectroscopy were performed to evaluate the physicochemical properties of the nanocomposites. Cellular adhesion, proliferation, and growth on the nanocomposites were evaluated using scanning electron microscopy. Cell viability tests revealed no significant differences among different trabeculae and cell types, indicating that these nanocomposites were not cytotoxic. The Fischer Koch modeling yielded satisfactory results and can thus be used in studies directed at diverse medical applications, including bone tissue engineering and implants.

Stress-strain and fatigue life numerical evaluation of two different dental implants considering isotropic and anisotropic human jaw

Dental prostheses are currently a valid solution for replacing potential missing tooth or edentulism clinical condition. Nevertheless, the oral cavity is a dynamic and complex system: occlusal loads, external agents, or other unpleasant events can impact on implants functionality and stability causing a future revision surgery. One of the failure origins is certainly the dynamic loading originated from daily oral activities like eating, chewing, and so on. The aim of this paper was to evaluate, by a numerical analysis based on Finite Elements Method (FEM), and to discuss in a comparative way, firstly, the stress-strain of two different adopted dental implants and, subsequently, their fatigue life according to common standard of calculations. For this investigation, the jawbone was modeled accounting for either isotropic or anisotropic behavior. It was composed of cortical and cancellous regions, considering it completely osseointegrated with the implants. The impact of implants' fixture design, loading conditions, and their effect on the mandible bone was finally investigated, on the basis of the achieved numerical results. Lastly, the life cycle of the investigated implants was estimated according to the well-established theories of Goodman, Soderberg, and Gerber by exploiting the outcomes obtained by the numerical simulations, providing interesting conclusions useful in the dental practice.

Mandibular Titanium Miniplates Change the Biomechanical Behaviour of the Mandible in the Case of Facial Trauma: A Three-Dimensional Finite Element Analysis

Our study aimed to compare the biomechanical behaviour of mandibles with or without titanium miniplates when subjected to an impact after bone healing using a finite element model (FEM) of the human mandible. We simulated mandibular trauma on an FEM of a human mandible carrying or not two parasymphyseal miniplates and applying a concentrated force of 2000 N to four different areas, including the insertion area, the area straddling the edge of the miniplates and the adjacent bone, at a distance from the miniplates on the symphysis, and on the basilar border of the mandible below the miniplates. Then, we compared the Von Mises stress distributions between the two models. In the case of an impact on the miniplates, the maximum Von Mises stress occurred in two specific areas, on the cortical bone at the posterior border of the two miniplates at a distance from the impact, while in the model without miniplates, the Von Mises stresses were homogenously distributed in the impact area. The presence of titanium miniplates in the case of trauma affects the biomechanical behaviour of the mandible and could cause more complex fractures. We recommend informing patients of this potential risk.

Surface Modification of WE43 Magnesium Alloys with Dopamine Hydrochloride Modified GelMA Coatings

As biodegradable medical implants, magnesium alloys have attracted great concerns due to their desirable biological and mechanical performances. Nevertheless, the overfast degradation rate of magnesium alloys makes it difficult to make full use of their potential in medical sciences. Therefore, it is a hot issue to control the degradation rate and functionalize the magnesium alloys via surface modifications. Herein, methacrylate gelatin (GelMA) hydrogel was adopted as coatings on the surface of WE43 magnesium alloys to control the degradation behaviors of magnesium alloys. Inspired by mussels, dopamine (DOPA) hydrochloride was adopted to modify GelMA to further functionalize the coatings. The compositions, swelling properties, degradation behaviors, and morphologies of samples were characterized by UV-Vis spectrophotometer, nuclear magnetic resonance (NMR), Fourier transform infrared spectroscopy (FTIR), scanning electron microscope (SEM), and immersion test. It was shown that GelMA-DOPA composites could be obtained and the swelling and degradation behaviors of magnesium alloys could be controlled by adjusting the compositions of GelMA and DOPA. Furthermore, the GelMA-DOPA hydrogel coatings can be tightly bonded to the Mg alloys.