Evaluation of a Double Layer Technique to Enhance Bone Formation in Atrophic Alveolar Ridge: Histologic Results of a Pilot Study

Double layer graft technique for horizontal alveolar ridge augmentation with staged implant placement: radiographic histological and implant stability analysis-a case report

INTRODUCTION

Horizontal ridge augmentation of a deficient alveolar bone site is performed either simultaneously with implant placement or in a staged approach prior to implant insertion. There are several available strategies for the augmentation of alveolar ridge deficiencies, including guided bone regeneration (GBR) through the use of barrier membranes. The success of the GBR approach mainly depends on the exclusion of soft tissue cells during bone remodeling.

CASE PRESENTATION

A healthy 25-year-old male patient presented with a missing upper left central incisor after clinical and radiographic examination, the site showed a class III defect horizontal atrophy. The procedure performed was the horizontal alveolar ridge augmentation using resorbable pericardium membrane with double layer graft technique (DLT) where autogenous bone placed as a first layer of the graft followed by xenograft as a second layer, the membrane was fixed with titanium pins. A cone beam computed tomography (CBCT) was performed before, immediately and 6 month following the surgery. After 6 months during implant placement, a core biopsy specimen was retrieved, stored and prepared for histological evaluation, with assessment of primary implant stability. The radiographic analysis showed a horizontal width gain of about 4 mm, at 6 month following implant placement, the implant was successfully osteointegrated with stability assessment also done after 6 months from placement.

CONCLUSION

DLT was successfully used for horizontal alveolar ridge augmentation, thus allowing a prosthetically driven implant placement. More cases assessing implant survival and success are needed to confirm the results of this case report.

Influence of direct prostheses on the condition of the alveolar processes during dental implantation

OBJECTIVE

The purpose of this article is to study of the processes accompanying osseointegration of the dental implants using various plate prostheses as temporary constructions, as well as to compare the dynamics of changes in the state of the jaw alveolar processes.

MATERIALS AND METHODS

The effect of dentures on the condition of the alveolar processes was studied in all patients according to the technique developed by L. Chulak on the 7th, 14th, 30th day and in 3, 6 months. To verify the results, the degree of atrophy of the alveolar processes was also determined by the second method the authors have chosen at the same time as indicated above.

RESULTS

The measurement results confirm linear changes in the height of the alveolar processes of the jaws with a decrease in the tissues of the prosthetic area. Throughout the duration of the examination, atrophy of the tissues of the alveolar processes is observed. Judging by the results obtained during the patients' study, it can be concluded that when applied as a temporary prosthesis with a dental delayed implantation of a partial denture made of polypropylene, the results of the state of the hard tissues of the mandible alveolar process show a better adaptation of the mucous membrane and slowing of atrophy of the jaw alveolar processes with this type of prosthetics.

Alveolar Bone Ridge Augmentation Using Polymeric Membranes: A Systematic Review and Meta-Analysis

Alveolar bone ridge resorption occurred after natural teeth loss and it can restrict the possibility of dental implants placement. The use of bone regenerative procedures is frequently required. The existing evidence regarding the efficacy of horizontal bone ridge augmentation trough guided bone regeneration (GBR) using polymeric membranes was stated. A systematic review and meta-analysis were performed. Electronic and manual literature searches were conducted. Screening process was done using the National Library of Medicine (MEDLINE by PubMed), Embase, and the Cochrane Oral Health. Included articles were randomized controlled trials and observational studies. Weighted means were calculated. Heterogeneity was determined using Higgins (I2). If I2 > 50% a random-effects model was applied. It was found that the mean of horizontal bone gain was 3.95 mm, ranging from 3.19 to 4.70 mm (confidence interval 95%). Heterogeneity is I2 = 99% (confidence interval 95%) and significance of the random-effects model was p < 0.001. The complications rate was 8.4% and membrane exposure was the most frequent. Through this study, we were able to conclude that the existing scientific evidence suggests that GBR using polymeric membranes is a predictable technique for achieving horizontal bone augmentation, thus, permitting a proper further implant placement.