A novel calcium phosphate-based nanocomposite for the augmentation of cement-injectable cannulated pedicle screws fixation: A cadaver and biomechanical study

High Strength and Shape Memory Spinal Fusion Device for Minimally Invasive Interbody Fusions

Introduction

Lumbar interbody fusion is widely employed for both acute and chronic spinal diseases interventions. However, large incision created during interbody cage implantation may adversely impair spinal tissue and influence postoperative recovery. The aim of this study was to design a shape memory interbody fusion device suitable for small incision implantation.

Methods

In this study, we designed and fabricated an intervertebral fusion cage that utilizes near-infrared (NIR) light-responsive shape memory characteristics. This cage was composed of bisphenol A diglycidyl ether, polyether amine D-230, decylamine and iron oxide nanoparticles. A self-hardening calcium phosphate-starch cement (CSC) was injected internally through the injection channel of the cage for healing outcome improvement.

Results

The size of the interbody cage is reduced from 22 mm to 8.8 mm to minimize the incision size. Subsequent NIR light irradiation prompted a swift recovery of the cage shape within 5 min at the lesion site. The biocompatibility of the shape memory composite was validated through in vitro MC3T3-E1 cell (osteoblast-like cells) adhesion and proliferation assays and subcutaneous implantation experiments in rats. CSC was injected into the cage, and the relevant results revealed that CSC is uniformly dispersed within the internal space, along with the cage compressive strength increasing from 12 to 20 MPa.

Conclusion

The results from this study thus demonstrated that this integrated approach of using a minimally invasive NIR shape memory spinal fusion cage with CSC has potential for lumbar interbody fusion.

A Biomechanical Study on Cortical Bone Trajectory Screw Fixation Augmented With Cement in Osteoporotic Spines

STUDY DESIGN

A biomechanical study.

OBJECTIVE

To evaluate the efficacy and feasibility of cement-augmented cortical bone trajectory (CBT) screw fixation.

METHODS

Forty-nine CBT screws were inserted into lumbar vertebrae guided by three-dimensionally printed templates, and then injected with 0, .5, or 1.0 mL of polymethylmethacrylate. The screw placement accuracy, cement dispersion, and cement leakage rate were evaluated radiologically. Biomechanical tests were performed to measure the axial pull-out strength and torque value.

RESULTS

Overall, 83.67% of the screws were inserted without pedicle perforation. In the 1.0 mL group, cement dispersed into the pedicle zone and formed a concentrated mass more often than in the .5 mL group, but not significantly more often (P > .05). The total cement leakage rate was 18.75%. Compared with the control group, the torque value was slightly higher in the .5 mL group (P = .735) and significantly higher in the 1.0 mL group (P = .026). However, there was no significant difference between the .5 and 1.0 mL groups (P = .431). The maximal pull-out force (Fmax) was increased by 52.85% and 72.73% in the .5 and 1.0 mL groups, respectively, compared with the control group (P < .05). However, the difference was not significant between the 2 cemented groups (P = .985).

CONCLUSIONS

Cement augmentation is a useful method for increasing CBT screw stability in osteoporotic spines. The cement injection volume is recommended to be 1 mL for each screw, and the cement should disperse into the vertebral body than the pedicle zones.

Evaluation of an Injectable Biphasic Calcium Sulfate/Hydroxyapatite Cement for the Augmentation of Fenestrated Pedicle Screws in Osteoporotic Vertebrae: A Biomechanical Cadaver Study

Cement augmentation of pedicle screws is one of the most promising approaches to enhance the anchoring of screws in the osteoporotic spine. To date, there is no ideal cement for pedicle screw augmentation. The purpose of this study was to investigate whether an injectable, bioactive, and degradable calcium sulfate/hydroxyapatite (CaS/HA) cement could increase the maximum pull-out force of pedicle screws in osteoporotic vertebrae. Herein, 17 osteoporotic thoracic and lumbar vertebrae were obtained from a single fresh-frozen human cadaver and instrumented with fenestrated pedicle screws. The right screw in each vertebra was augmented with CaS/HA cement and the un-augmented left side served as a paired control. The cement distribution, interdigitation ability, and cement leakage were evaluated using radiographs. Furthermore, pull-out testing was used to evaluate the immediate mechanical effect of CaS/HA augmentation on the pedicle screws. The CaS/HA cement presented good distribution and interdigitation ability without leakage into the spinal canal. Augmentation significantly enhanced the maximum pull-out force of the pedicle screw in which the augmented side was 39.0% higher than the pedicle-screw-alone side. Therefore, the novel biodegradable biphasic CaS/HA cement could be a promising material for pedicle screw augmentation in the osteoporotic spine.

A Novel Calcium Phosphate-Based Nanocomposite for Augmentation of Cortical Bone Trajectory Screw Fixation

Purpose

To evaluate the effect of cement augmentation of cortical bone trajectory (CBT) screws using a novel calcium phosphate–based nanocomposite (CPN).

Material and Methods

CBT screws were placed into cadaveric lumbar vertebrae. Depending on the material used for augmentation, they were divided into the following three groups: CPN, polymethylmethacrylate (PMMA), and control. Radiological imaging was used to evaluate the cement dispersion. Biomechanical tests were conducted to measure the stability of CBT screws. A rat cranial defect model was used to evaluate biodegradation and osseointegration of the CPN.

Results

After cement augmentation, the CPN tended to disperse into the distal part of the screws, whereas PMMA remained limited to the proximal part of the screws (P < 0.05). As for cement morphology, the CPN tended to form a concentrated mass, whereas PMMA arranged itself as a scattered cement cloud, but the difference was not significant (P > 0.05). The axial pullout test showed that the average maximal pullout force (Fmax) of CPN-augmented CBT screws was similar to that of the PMMA group (CPN, 1639.56 ± 358.21 N vs PMMA, 1778.45 ± 399.83 N; P = 0.745) and was significantly greater than that of the control group (1019.01 ± 371.98 N; P < 0.05). The average torque value in the CPN group was higher than that in the control group (CPN, 1.51 ± 0.78 N∙m vs control, 0.97 ± 0.58 N∙m) and lower than that in the PMMA group (1.93 ± 0.81 N∙m), but there were no statistically significant differences (P > 0.05). The CPN could be biodegraded and gradually replaced by newly formed bone tissue after 12 weeks in a rat cranial defect model.

Conclusion

The biocompatible CPN could be a valuable augmentation material to enhance CBT screw stability.

The Biomechanical Properties of Cement-Augmented Pedicle Screws for Osteoporotic Spines

STUDY DESIGN

This is a broad, narrative review of the literature.

OBJECTIVE

In this review, we describe recent biomechanics studies on cement-augmented pedicle screws for osteoporotic spines to determine which factors influence the effect of cement augmentation.

METHODS

A search of Medline was performed, combining the search terms "pedicle screw" and ("augmentation" OR "cement"). Articles published in the past 5 years dealing with biomechanical testing were included.

RESULTS

Several factors have been identified to impact the effect of cement augmentation in osteoporotic spines. These include the type of augmentation material, the volume of injected cement, the timing of augmentation, the severity of osteoporosis, the design of the pedicle screw, and the specific augmenting technique, among others.

CONCLUSIONS

This review elaborates the biomechanics of cement-augmented pedicle screws, determines which factors influence the augmentation effect, and identifies the risk factors of cement leakage in osteoporotic bone, which might offer some guidance when using this technique in clinical practice. Further, we provide information about newly designed screws and recently developed augmentation materials that provide higher screw stability as well as fewer cement-related complications.

Calcium phosphate-based composite cement: Impact of starch type and starch pregelatinization on its physicochemical properties and performance in the vertebral fracture surgical models in vitro

Calcium phosphate cement (CPC) modified with native and pregelatinized normal corn and waxy maize starches was studied. Effects of starch pregelatinization and starch type on the physicochemical properties of CPC were investigated. CPC modified with pregelatinized normal corn starch (CPB-PNC) or pregelatinized waxy maize starch (CPB-PW) was evaluated by two vertebral fracture surgical models in vitro. Both granular and pregelatinized starches significantly improved the setting times and injectability of CPC, but only the pregelatinized starches improved the anti-collapsibility and compressive strength of CPC significantly. CPB-PW, whose micro-structure was compact and uniform, showed the best physicochemical properties. Addition of starch did not inhibit the hydro-reaction of CPC. Unmodified CPC had very poor dispersibility and could not apply in the tests of the surgical models. Pregelatinized starch especially waxy maize starch improved the dispersibility of CPC and showed good dispersion area, volume, improved pull-out force and maximum torque in the Sawbones sponge model. Similarly, in the minimally invasive kyphoplasty model, CPB-PNC and CPB-PW could disperse in the osteoporotic sheep vertebrae and improve the compressive strength of the sheep vertebral body. In conclusion, starch pregelatinization and starch botanical source affect the physicochemical properties of CPC significantly. Bone cements modified by different starches also performed differently in surgical models for osteoporotic vertebral fracture. Pregelatinized waxy maize starch may be a better candidate for CPC modification comparing to the pregelatinized normal corn starch.