A generic gas chromatography method for determination of residual solvents in PET radiopharmaceuticals

OMNI: Gas Chromatograph Captures Seven Common PET Radiotracer Analytes in under 5 Minutes

A novel gas chromatography method was developed using automatic injections to identify and quantify the amount of residual solvents or analytes in samples of fluorine-18 and carbon-11 radiopharmaceuticals. This approach evaluates seven analytes in less than 5 versus 13 min of acquisition time. The method additionally includes a 3 min bakeout to aid in the removal and carry-over of higher-boiling impurities. Chromatographic parameters such as column temperature, hold time, column pressure, flow rate, and split ratios were adjusted and optimized to analyze radioactive drug samples containing analytes which include methanol, ethanol, acetone, acetonitrile, triethylamine, N,N-dimethylformamide, and dimethyl sulfoxide. The relative standard deviation for each solvent was determined to be no greater than 1.6%. The method limit of detection (LOD) and limit of quantification (LOQ) were between 0.053 and 0.163 and 0.000 (5.791 × 10-6) and 0.520 mg/mL, respectively. This GC technique, using flame ionization detection (FID), was validated and is currently employed for the routine quality control of all approved IND and RDRC PET radiopharmaceuticals at our center.

Chromatographic method development using multivariate approaches for organic solvents optimized analysis in [18F]fluorocholine

A fast and simple method using Gas Chromatography combined with Flame Ionization Detection (GC-FID) was developed for the determination of ethanol, acetonitrile, dibromomethane, dimethylaminoethanol, and dimethyl sulfoxide in [¹⁸F]fluorocholine. The combination of fractional factorial design, Doehlert design, and Desirability function was used to evaluate the operational parameters and to establish the best working condition. The validation results revealed that the proposed method has good recovery (85.1-104.1%) and repeatability (RSD ≤8.1%). Correlation coefficients (R ≥ 0.983) indicated good linearity over a wide range. The limit of detection (≤2.5 ppm) and the limit of quantification (≤7.5 ppm) were satisfactory. The proposed method is based on minimum manual operation, sample preparation free, direct injection technique, and short chromatographic separation time. This method is useful for routine analysis of organic solvents in [¹⁸F]fluorocholine, feasible for the modernization of specific monograph, and was therefore successfully implemented to assess samples manufactured by Nuclear Technology Development Center (CDTN).

Platform headspace gas chromatography method for high-throughput determination of residual solvents in pharmaceutical materials

Static headspace capillary gas chromatography (HSGC) has been employed to monitor the level of residual solvents in the pharmaceutical materials. Most of the HSGC methods, however, consume significant amounts of diluents and require considerable amount of sample preparation time. Accordingly, a HSGC method featured with fast turnaround time, and minimal amount of solvent use has been developed for the quantitative analysis of 27 residual solvents frequently used in the development and manufacturing processes of pharmaceutical industry. This HSGC-FID method employs a commercially available fused silica capillary column, a split injection (40:1), and a programmed temperature ramp. It was qualified for specificity, accuracy, repeatability/precision, linearity, LOQ, solution stability, and robustness using two representative sample matrices. The standards, samples and spiked samples were demonstrated to be stable for at least 10 days at room temperature in sealed headspace vials with a recovery of ≥ 93%. The method was also shown to be robust, and its performance was not affected by small changes of carrier gas flow rate, initial oven temperature or the headspace oven temperature. In this new approach, the analytical sample was prepared by dissolving the sample into 1 mL of the diluent and the standard solution was prepared by diluting 1 mL of the custom-made stock into 9 mL of the diluent whereas the traditional approach requires liters of the diluent, making the new approach environmentally friendly, sustainable, economical, agile, error-proofing and thus appropriate for a variety of pharmaceutical applications.