Electrochemical study and application on rutin at chitosan/graphene films modified glassy carbon electrode

Electrochemical Determination of Morin in Natural Food Using a Chitosan-Graphene Glassy Carbon Modified Electrode

This report presents a new application for the chitosan-graphene glassy carbon electrode (Ch-G/GCE) system in the determination of the hydroxyflavonoid morin (MR), one of the flavonoids with the highest favorable activity for people, due to its natural properties by square-wave voltammetry (SWV). The anodic peak current for MR was observed at 0.50 V with an increase of 73% compared with the glassy carbon electrode unmodified. The surface areas of Ch-G/GCE, Ch/GCE and GCE evaluated by cyclic voltammetry were 0.140, 0.053 and 0.011 cm², respectively. Additionally, an increase greater than 100% compared to the electrode without modification was observed. The detection limit was 0.30 µmol/L for MR, and the relative standard deviations (RSDs) were 1.8% (n = 6). Possible interferences as quercetin, rutin, and applications in real samples were also evaluated with very acceptable results.

Surfactant-free solvothermal synthesis of Cu-MOF via protonation-deprotonation approach: A morphological dependent electrocatalytic activity for therapeutic drugs

A copper-1,4-naphthalenedicarboxylic acid-based organic framework (Cu-NDCA MOF) with different morphologies was synthesized by solvothermal synthetic route via a simple protonation-deprotonation approach. The synthesized Cu-NDCA MOFs were analyzed by diverse microscopic and spectral techniques. The FE-SEM and TEM image results exhibited the flake-like (FL), partial anisotropic (PAT), and anisotropic (AT)-Cu-NDCA MOFs formation obtained at different pH (3.0, 7.0, and 9.0) of the reaction medium. The AT-Cu-NDCA MOF/GC electrode not only increases the electroactive surface area but also boosts the electron transfer rate reaction compared to other modified electrodes (PAT- and FL-Cu-NDCA MOFs/GCEs). Under the optimized conditions, the modified electrode (AT-Cu-NDCA MOF) exhibited a sharp oxidation peak (+ 0.46 V vs. Ag/AgCl) and higher current response for rutin. The electrode provides a wide linear range from 1 × 10^-9 to 50 × 10^-6 M, a low detection limit of 1.21 × 10^-10 M, LOQ of 0.001 μM, and sensitivity of 0.149 μA μM^-1 cm^-2. The AT-Cu-NDCA MOF/GC electrode exhibited good stability (RSD = 3.52 ± 0.02% over 8 days of storage), and excellent reproducibility (RSD = 2.62 ± 0.02% (n = 3)). The modified electrode was applied to the determination of rutin in apple, orange, and lemon samples with good recoveries (99.79-99.91, 99.24-99.69, and 99.53-99.83, respectively). Graphical abstract Anisotropic structure of Cu-NDCA MOFs and its modification on glassy carbon electrode for ultra-sensitive determination of rutin in fruit samples.

A chitosan grafted mesoporous carbon aerogel for ultra-sensitive voltammetric determination of isoniazid

A screen-printed carbon electrode (SPCE) was modified with chitosan (Chit) supported on carbon aerogel (CA) to obtain an electrochemical sensor for the tuberculosis drug isoniazid (INZ). The interconnected mesoporous structure of Chit/CA provides a large surface area (S_BET = 461 m² g^-1) and good porosity (V_Tot = 0.69 cm³ g^-1). Besides, the modified SPCE displayed enhanced electrocatalytic activity due to the presence of numerous active sites (such as >C=O, -NH-, -NH₂, -OH). Figures of merit include (a) a typical working voltage of 0.28 V (vs. Ag/AgCl), (b) high sensitivity (8.09 μA μM^-1 cm^-2), (c) a wide linear response to INZ (0.01-115 μM) and (d) a low detection limit (8 nM). The modified electrode has successfully been applied to the determination of INZ in spiked serum and urine, and recoveries ranged from 97.8 to 99.8%. Graphical abstract Schematic illustration of preparation and applications of a nanocomposite consisting of chitosan (Chit; CS) supported on carbon aerogel (CA) for electrochemical detection of isoniazid.

Polyphenol oxidase/gold nanoparticles/mesoporous carbon-modified electrode as an electrochemical sensing platform for rutin in dark teas

In the communication, by virtue of the excellent conductivity and great surface area of mesoporous carbon (FDU-15), the enhanced conductivity of Au NPs, and the good electrochemical response of polyphenol oxidase (PPO) to rutin, a PPO/AuNPs/FDU-15-modified electrode was used as a candidate for the determination of rutin in dark teas with satisfactory results.

By virtue of great surface area of mesoporous carbon, enhanced conductivity of AuNPs, and good electrochemical response of polyphenol oxidase to rutin, a PPO/AuNPs/FDU-15-modified electrode was used for the determination of rutin in dark teas.

Electrocomposite Developed with Chitosan and Ionic Liquids Using Screen-Printed Carbon Electrodes Useful to Detect Rutin in Tropical Fruits

This work reports the development of a composite of the ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIM]BP₄) and chitosan (CS) described in previous reports through a new method using cyclic voltammetry with 10 cycles at a scan rate of 50.0 mV s⁻¹. This method is different from usual methods such as casting, deposition, and constant potential, and it allows the development of an electroactive surface toward the oxidation of rutin by stripping voltammetry applied to the detection in tropical fruits such as orange, lemon, and agraz (Vaccinium meridionale Swartz), with results similar to those reported in previous studies. In addition, the surface was characterized by electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM), and Raman spectroscopy. The limit of detection was 0.07 µmol L⁻¹ and the relative standard deviation (RSD) of 10 measurements using the same modified electrode was 0.86%. Moreover, the stability of the sensor was studied for six days using the same modified electrode, where the variation of the signal using a known concentration of rutin (RT) was found to be less than 5.0%. The method was validated using a urine chemistry control spiked with known amounts of RT and possible interference was studied using ten substances including organic and biological compounds, metal ions, and dyes. The results obtained in this study demonstrated that this electrodeveloped composite was sensitive, selective, and stable.

Core-shell hyperbranched chitosan nanostructure as a novel electrode modifier

The present study reports, for the first time, the development and use of core-shell amino-terminated chitosan (Cs) hyperbranched nanoparticles (HBCs-NH₂ NPs) as a novel natural polymer-based electrode modifier for efficient electrochemical systems. The electrochemical activity of the developed HBCs-NH₂ NPs as compared to Cs NPs was identified by standard oxidation-reduction reactions of ferricyanide. The oxidation-reduction peaks height was about twofold higher than the response of Cs-modified electrode. On the other hand, NADH oxidation at the nanostructured surfaces confirmed the electrocatalytic activity where the oxidation of NADH appeared at a lower overpotential (from 805mV to 635mV vs Ag/AgCl). Eventually, a diffusion-controlled process was confirmed from the scan rate effect.