Kinetic performance comparison of fully and superficially porous particles with sizes ranging between 2.7 μm and 5 μm: Intrinsic evaluation and application to a pharmaceutical test compound

Column selection considerations in compact capillary liquid chromatography

Recent years have seen significant advances in compact, portable capillary LC instrumentation. This study explores the performances of several commercially available columns within the pressure and flow limits of both the columns and one of these compact LC instruments. The commercially available compact capillary LC system with UV-absorbance detector used in this study is typically operated using columns in the 0.15-0.3 mm internal diameter (i.d.) range. Efficiency measurements (i.e., theoretical plates, N) for six columns with i.d.s in this range and of varying lengths and pressure limits, packed with stationary phases of different particle diameters and morphologies, were made using a mixture of standard alkylphenones. Kinetic plot comparisons between columns that vary by one (or more) of these parameters are described, along with calculated kinetic performance and Knox-Saleem limits. These theoretical performance descriptions provide insight into optimal operating conditions when using capillary LC systems. Based on kinetic plot evaluation of available capillary columns in the 0.2-0.3 mm i.d. range with a conservative upper pressure limit of 330 bar packed with superficially porous particles, a 25 cm column could generate ∼47,000 plates in 7.85 min when operated at 2.4 µL/min. For comparison, more robust 0.3 mm i.d. columns (packed with fully porous particles) that can be operated at higher pressures than can be provided by the pumping system (conservative pump upper pressure limit of 570 bar), a ∼20 cm column could generate nearly 40,000 plates in 5.9 min if operated at 6 µL/min. Across all capillary LC columns measured, higher pressure limits and shorter columns can provide the best throughput when considering both speed and efficiency.

Preparation of mixed-mode stationary phase for separation of peptides and proteins in high performance liquid chromatography

Porous silica particles were prepared by sol–gel method with some modification to get wide-pore particles. These particles were derivatized with N-phenylmaleimide-methylvinylisocyanate (PMI) and styrene by reversible addition fragmentation chain transfer (RAFT) polymerization to prepare N-phenylmaleimide embedded polystyrene (PMP) stationary phases. Narrow bore stainless steel column (100 × 1.8 mm i.d) was packed by slurry packing method. The chromatographic performance of PMP column was evaluated for the separation of synthetic peptides mixture composed of five peptides (Gly-Tyr, Gly-Leu-Tyr, Gly-Gly-Tyr-Arg, Tyr-Ile-Gly-Ser-Arg, Leucine enkephalin) and tryptic digest of human serum albumin (HAS) respectively. Number of theoretical plates as high as 280,000 plates/m were obtained for peptides mixture at optimum elution condition. Separation performance of the developed column was compared with commercial Ascentis Express RP-Amide column and it was observed that separation performance of PMP column was better than commercial column in terms of separation efficiency and resolution.

Development and Validation of a Chiral Liquid Chromatographic Assay for Enantiomeric Separation and Quantification of Verapamil in Rat Plasma: Stereoselective Pharmacokinetic Application

A novel, fast and sensitive enantioselective HPLC assay with a new core-shell isopropyl carbamate cyclofructan 6 (superficially porous particle, SPP) chiral column (LarihcShell-P, LSP) was developed and validated for the enantiomeric separation and quantification of verapamil (VER) in rat plasma. The polar organic mobile phase composed of acetonitrile/methanol/trifluoroacetic acid/triethylamine (98:2:0.05: 0.025, v/v/v/v) and a flow rate of 0.5 mL/min was applied. Fluorescence detection set at excitation/emission wavelengths 280/313 nm was used and the whole analysis process was within 3.5 min, which is 10-fold lower than the previous reported HPLC methods in the literature. Propranolol was selected as the internal standard. The S-(-)- and R-(+)-VER enantiomers with the IS were extracted from rat plasma by utilizing Waters Oasis HLB C18 solid phase extraction cartridges without interference from endogenous compounds. The developed assay was validated following the US-FDA guidelines over the concentration range of 1-450 ng/mL (r2 ≥ 0.997) for each enantiomer (plasma) and the lower limit of quantification was 1 ng/mL for both isomers. The intra- and inter-day precisions were not more than 11.6% and the recoveries of S-(-)- and R-(+)-VER at all quality control levels ranged from 92.3% to 98.2%. The developed approach was successfully applied to the stereoselective pharmacokinetic study of VER enantiomers after oral administration of 10 mg/kg racemic VER to Wistar rats. It was found that S-(-)-VER established higher Cmax and area under the concentration-time curve (AUC) values than the R-(+)-enantiomer. The newly developed approach is the first chiral HPLC for the enantiomeric separation and quantification of verapamil utilizing a core-shell isopropyl carbamate cyclofructan 6 chiral column in rat plasma within 3.5 min after solid phase extraction (SPE).

Basic Structure-Independent Equations of Kinetic Performance of Columns in Liquid Chromatography

The lowest dimensionless plate height (h_min) of the liquid chromatography (LC) column is a subjective metric that cannot be found from measurements of parameters of a column as a separation device and is not suitable for comparison of kinetic performance of differently structured columns. In some cases (monolithic, pillar-array columns), there is no correlation between h_min (as it is currently understood) and the column performance. The same is true for the flow resistance parameter (ϕ). Recently introduced measurable effective diameter and structural quality factor (q_max) of a column are objective replacements for ϕ and h_min. Metric q_max, the maximum of the flow-dependent kinetic performance factor (q), is suitable for comparison of differently structured columns. Structure-independent basic equations binding kinetic performance of LC column with its q and other parameters and operational conditions were developed. It has been shown that previously known and new equations of a column kinetic performance can be derived from the basic ones. An example of using the equations for solving a known practical problem of column selection is provided.

Fundamental to achieving fast separations with high efficiency: A review of chromatography with superficially porous particles

Types of particles have been fundamental to LC separation technology for many years. Originally, LC columns were packed with large-diameter (>100 μm) calcium carbonate, silica gel, or alumina particles that prohibited fast mobile-phase speeds because of the slow diffusion of sample molecules inside deep pores. During the birth of HPLC in the 1960s, superficially porous particles (SPP, ≥30 μm) were developed as the first high-speed stationary-phase support structures commercialized, which permitted faster mobile-phase flowrates due to the fast movement of sample molecules in/out of the thin shells. These initial SPPs were displaced by smaller totally porous particles (TPP) in the mid-1970s. But SPP history repeated when UHPLC emerged in the 2000s. Stationary-phase support structures made from sub-3-μm SPPs were introduced to chromatographers in 2006. The initial purpose of this modern SPP was to enable chromatographers to achieve fast separations with high efficiency using conventional HPLCs. Later, the introduction of sub-2-μm SPPs with UHPLC instruments pushed the separation speed and efficiency to a very fast zone. This review aims at providing readers a comprehensive and up-to-date view on the advantages of SPP materials over TPPs historically and theoretically from the material science angle.

Through-pore polymerization in polar high-performance liquid chromatography columns allowing scanning electron microscopy based imaging of the packing order

To allow an enhanced understanding of the order in packed HPLC columns, in this work a methodology for immobilizing native polar silica particles is developed based on the polymerization of a methyl methacrylate (MMA) and ethylene glycol dimethacrylate (EGDMA) as a cross-linker in the interstitial pores of HPLC columns. Subsequent mechanical cutting then allows scanning electron microscopy (SEM) based imagery of cross-sections of the packed bed. In this way, the packing efficiency of home-made and commercial HPLC columns with 4.6 mm inner diameter and 150 mm length comprising the same packing material of 5 µm silica particles are compared. The methodology is developed for native silica used in e.g. hydrophilic interaction liquid chromatography (HILIC) and in normal phase LC. In order to confirm the feasibility of the developed methodology, the conventional methods for the evaluation of column, efficiency and porosity, are also employed. The obtained porosity information is compared and showed the same trend with the external porosity measurements obtained via inverse size exclusion approach, illustrating its potential application to study the micro-heterogeneity of packed HPLC columns and to guide the optimization of the packing process of HPLC columns.

Application of chiral chromatography in radiopharmaceutical fields: A review

Chiral column chromatography (CCC) is a revolutionary analytical methodology for the enantioseparation of novel positron emission tomography (PET) tracers in the primary stages of drug development. Due to the different behaviors of tracer enantiomers (e.g. toxicity, metabolism and side effects) in administrated subjects, their separation and purification is a challenging endeavor. Over the last three decades, different commercial chiral columns have been applied for the enantioseparation of PET-radioligand (PET-RL) or radiotracers (PET-RT), using high-performance liquid chromatography (HPLC). The categorization and reviewing of them is a vital topic. This review presents a brief overview of advances, applications, and future prospectives of CCC in radiopharmaceutical approaches. In addition, the effective chromatographic parameters and degravitation trends to enhance enantioseparation resolution are addressed. Moreover, the application and potential of chiral super fluidical chromatography (CSFC) as an alternative for enantioseparation in the field of radiopharmaceutical is discussed. Finally, the crucial application challenges of CCC are explained and imminent tasks are suggested.

Cyclofructans as Chiral Selectors: An Overview

Cyclofructans are cyclic oligosaccharides made of β-2,1-linked fructofuranose units. They have been utilized as chiral selectors, usually after derivatization, with high-performance liquid chromatography (HPLC), gas chromatography (GC), capillary electrophoresis (CE), and supercritical fluid chromatography (SFC). The focus herein will be directed to their development and applications as chiral selectors in various chiral separation techniques. Discussion of their use in hydrophilic liquid interaction chromatography (HILIC) will be limited. Their use in liquid chromatography, especially their improvements with the use of superficially porous particles (SPPs) will be emphasized. Method parameters and future directions are also discussed.

Comparison between core-shell and totally porous particle stationary phases for fast and green LC determination of five hepatitis-C antiviral drugs

The performances of core-shell 2.7 μm and fully porous sub-2 μm particles packed in narrow diameter columns were compared under the same chromatographic conditions. The stationary phases were compared for fast separation and determination of five new antiviral drugs; daclatasvir, sofosbuvir, velpatasvir, simeprevir, and ledipasvir. The gradient elution was done using ethanol as green organic modifier, which is more environmentally friendly. Although both columns provided very good resolution of the five drugs, core-shell particles had proven to be of better efficiency. Under gradient elution conditions, core-shell particles exhibited faster elution, better peak shape, and enhanced resolution adding to lower system backpressure. The column backpressure on sub-2 μm particles was more than twice that on core-shell particles. This gives a chance to use conventional high-performance liquid chromatography conditions without needing special instrumentation as that required for ultra-high performance liquid chromatography. The method was validated for determination of the five drugs by gradient elution using mobile phase composed of organic modifier ethanol and aqueous part containing 0.75 g sodium octane sufonate and 3.0 g sodium dihydrogen phosphate per liter at pH of 6.15. Detection was done using UV-detector set at 210 nm. The linearity, accuracy, and precision were found very good within the concentration range of 2-200 μg/mL.

Temperature Effects on Retention and Separation of PAHs in Reversed-Phase Liquid Chromatography Using Columns Packed with Fully Porous and Core-Shell Particles

Effects of temperature on the reversed-phase chromatographic behavior of PAHs were investigated on three columns. The first was the recent C18column (250 mm × 4.6 mm) packed with 5 µm core-shell particles while the others were more conventional C18columns (250 mm × 4.6 mm) packed with fully porous particles. Among the 16 PAHs studied, special attention has been paid to two pairs of PAHs, fluorene/acenaphthene and chrysene/benzo[a]anthracene, which often present coeluting problems. Due to the low surface area of the core-shell particles, lowest retention time of each PAH was highlighted and effects of the temperature on the separation of PAHs were negligible in regard to those using columns packed with fully porous particles. For each PAH studied, it was demonstrated that peaks were symmetrical and may be considered as Gaussian peaks when the column packed with core-shell particle was employed. In the best condition, the separation of PAHs was conducted at 16°C under very low pressure values (670–950 psi = 46–65 bars). Depending on PAHs, the limit of detection ranged from 0.88 to 9.16 μg L−1. Analysis of spiked acetonitrile samples with PAHs at 10 and 50 µg L−1and tap water at 10 µg L−1gave very good recoveries (94%–109.3%) and high precision (1.1%–3.5%).

Evaluation of 5 µm Superficially Porous Particles for Capillary and Microfluidic LC Columns

Large-size (4–5 µm) superficially porous particles yield lower plate heights (e.g., the minimal reduced plate height or h_min ≈ 1.5) than fully porous particles of a similar size when packed into large-bore columns. This property allows for better chromatographic performance without the higher pressures required for smaller particles. This study explores the use of such particles in microfluidic LC columns where materials and fitting pressure limits can constrain the size of particle used. The theoretically predicted performance improvements compared to fully porous particles were not demonstrated in capillary columns (with h_min ≈ 2 for both particle types), in agreement with previous studies that examined smaller superficially porous particles. Microfluidic columns were then compared to capillary columns. Capillary columns significantly outperformed microfluidic columns due to imperfections imposed by microfluidic channel asymmetry and world-to-chip connection at the optimal flow rate; however, superficially porous particles packed in microfluidic LC columns had flatter plate height versus flow rate curves indicating potential for better performance at high reduced velocities.

Gone in seconds: praxis, performance, and peculiarities of ultrafast chiral liquid chromatography with superficially porous particles

A variety of brush-type chiral stationary phases (CSPs) were developed using superficially porous particles (SPPs). Given their high efficiencies and relatively low back pressures, columns containing these particles were particularly advantageous for ultrafast "chiral" separations in the 4-40 s range. Further, they were used in all mobile phase modes and with high flow rates and pressures to separate over 60 pairs of enantiomers. When operating under these conditions, both instrumentation and column packing must be modified or optimized so as not to limit separation performance and quality. Further, frictional heating results in axial thermal gradients of up to 16 °C and radial temperature gradients up to 8 °C, which can produce interesting secondary effects in enantiomeric separations. It is shown that the kinetic behavior of various CSPs can differ from one another as much as they differ from the well-studied C18 reversed phase media. Three additional interesting aspects of this work are (a) the first kinetic evidence of two different chiral recognition mechanisms, (b) a demonstration of increased efficiencies at higher flow rates for specific separations, and

Comparison of superficially porous and fully porous silica supports used for a cyclofructan 6 hydrophilic interaction liquid chromatographic stationary phase

A new HILIC stationary phase comprised of native cyclofructan-6 (CF6) bonded to superficially porous silica particles (2.7μm) was developed. Its performance was evaluated and compared to fully porous silica particles with 5μm (commercially available as FRULIC-N) and 3μm diameters. Faster and more efficient chromatography was achieved with the superficially porous particles (SPPs). The columns were also evaluated in the normal phase mode. The peak efficiency, analysis time, resolution, and overall separation capabilities in both HILIC and normal phase modes were compared. The analysis times using the superficially porous based column in HILIC mode were shorter and the theoretical plates/min were higher over the entire range of flow rates studied. The column containing the superficially porous particles demonstrated higher optimum flow rates than the fully porous particle packed columns. At higher flow rates, the advantages of the superficially porous particles was more pronounced in normal phase separations than in HILIC, clearly demonstrating the influence that the mode of chromatography has on band broadening. However, the minimum reduced plate heights (hmin) were typically lower in HILIC than in the normal phase mode. Overall, the superficially porous particle based CF6 column showed clear advantages over the fully porous particle columns, in terms of high throughput and efficient separations of polar compounds in the HILIC mode.

Green chromatography-carbon footprint of columns packed with core–shell materials

Acetonitrile and methanol are the most popular organic solvents employed in RP HPLC, so it is important to minimize the environmental impact of organic solvent and the use of environmentally friendly solvents.

Derringer desirability and kinetic plot LC-column comparison approach for MS-compatible lipopeptide analysis

Lipopeptides are currently re-emerging as an interesting subgroup in the peptide research field, having historical applications as antibacterial and antifungal agents and new potential applications as antiviral, antitumor, immune-modulating and cell-penetrating compounds. However, due to their specific structure, chromatographic analysis often requires special buffer systems or the use of trifluoroacetic acid, limiting mass spectrometry detection. Therefore, we used a traditional aqueous/acetonitrile based gradient system, containing 0.1% (m/v) formic acid, to separate four pharmaceutically relevant lipopeptides (polymyxin B₁, caspofungin, daptomycin and gramicidin A₁), which were selected based upon hierarchical cluster analysis (HCA) and principal component analysis (PCA).

In total, the performance of four different C18 columns, including one UPLC column, were evaluated using two parallel approaches. First, a Derringer desirability function was used, whereby six single and multiple chromatographic response values were rescaled into one overall D-value per column. Using this approach, the YMC Pack Pro C18 column was ranked as the best column for general MS-compatible lipopeptide separation. Secondly, the kinetic plot approach was used to compare the different columns at different flow rate ranges. As the optimal kinetic column performance is obtained at its maximal pressure, the length elongation factor λ (P_max/P_exp) was used to transform the obtained experimental data (retention times and peak capacities) and construct kinetic performance limit (KPL) curves, allowing a direct visual and unbiased comparison of the selected columns, whereby the YMC Triart C18 UPLC and ACE C18 columns performed as best. Finally, differences in column performance and the (dis)advantages of both approaches are discussed.