Photocatalytic activity of TiO2 films immobilized on aluminum foam by atomic layer deposition technique

Photocatalysts for a sustainable future: Innovations in large-scale environmental and energy applications

The growing environmental and energy crises have prompted researchers to seek new solutions, including large-scale photocatalytic environmental remediation and the production of solar hydrogen using photocatalytic materials. To achieve this goal, scientists have developed numerous photocatalysts with high efficiency and stability. However, the large-scale application of photocatalytic systems under real-world conditions is still limited. These limitations arise at every step, including the large-scale synthesis and deposition of photocatalyst particles on a solid support, and the development of an optimal design with high mass transfer and efficient photon absorption. The purpose of this article is to provide a detailed description of the primary challenges and potential solutions encountered in scaling up photocatalytic systems for use in large-scale water and air purification and solar hydrogen production. Additionally, based on a review of current pilot developments, we draw conclusions and make comparisons regarding the main operating parameters that affect performance, as well as propose strategies for future research.

Tunable TiO2-BN-Pd nanofibers by combining electrospinning and atomic layer deposition to enhance photodegradation of acetaminophen

The demand for fresh and clean water sources is increasing globally, and there is a need to develop novel routes to eliminate micropollutants and other harmful species from water. Photocatalysis is a promising alternative green technology that has shown great performance in the degradation of persistent pollutants. Titanium dioxide is the most used catalyst owing to its attractive physico-chemical properties, but this semiconductor presents limitations in the photocatalysis process due to the high band gap and the fast recombination of the photogenerated carriers. Herein, a novel photocatalyst has been developed, based on titanium dioxide nanofibers (TiO2 NFs) synthesized by electrospinning. The TiO2 NFs were coated by atomic layer deposition (ALD) to grow boron nitride (BN) and palladium (Pd) on their surface. The UV-Vis spectroscopy measurements confirmed the increase of the band gap and the extension of the spectral response to the visible range. The obtained TiO2/BN/Pd nanofibers were then tested for photocatalysis, and showed a drastic increase of acetaminophen (ACT) degradation (>90%), compared to only 20% degradation obtained with pure TiO2 after 4 h of visible light irradiation. The high photocatalytic activity was attributed to the good dispersion of Pd NPs on TiO2-BN nanofibers, leading to a higher transfer of photoexcited hole carriers and a decrease of photogenerated electron-charge recombination. To confirm its reusability, recycling tests on the hybrid photocatalyst TiO2/BN/Pd have been performed, showing a good stability over 5 cycles under UV and visible light. In addition, toxicity tests as well as quenching tests were carried out to check the toxicity of the byproducts formed and to determine active species responsible for the degradation. The results presented in this work demonstrate the potential of TiO2/BN/Pd nanomaterials, and open new prospects for the preparation of tunable photocatalysts.

Photocatalytic Degradation of Dissolved Phenol by Immobilized Zinc Oxide Nanoparticles: Batch Studies, Continuous Flow Experiments, and Numerical Modeling

In spite of the progress achieved on the photo-catalytic treatment of water streams, there is still a gap of knowledge on the optimization of the performance of continuous-flow photo-reactors. Zinc-oxide (ZnO) nanoparticles were immobilized on Duranit (80% silica + 20% alumina) inert balls with dip-coating and thermal annealing. The immobilized ZnO nanoparticles were characterized by scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX), X-ray diffraction (XRD), ultraviolet-visible (UV-Vis) spectroscopy, and Raman spectroscopy. To assess the stability and photocatalytic capacity of immobilized ZnO, degradation tests of phenol were performed in batch mode in a 22 W UV-oven with an emission peak at 375 nm by varying the temperature, the initial phenol concentration, and the ratio of photocatalyst mass to initial phenol mass. Continuous flow tests were conducted on two types of annular photo-reactors, made of poly(methyl)methacrylate (PMMA) and stainless steel (STST), equipped with a 6 W UV-lamp with emission at 375 nm, packed with ZnO-coated Duranit beads. Experiments were conducted by recirculating the phenol solution between the annular space of reactor and an external tank and varying the flow rate and the liquid volume in the tank. A one-dimensional dynamic mathematical model was developed by combining reactive with mass-transfer processes and used to estimate the overall reaction kinetic constant with inverse modeling. The results revealed that the ZnO losses might be discernible in batch mode due to the intense stirring caused by the bubbles of injected air, while an insignificant loss of ZnO mass occurs under continuous flow conditions, even after several cycles of reuse; the order of the overall phenol photodegradation reaction is lower than unity; the pseudo-1st order kinetic constant scales positively with the ratio of photocatalyst mass to the initial phenol mass and Peclet number.

Self-cleaning, photocatalytic films on aluminum plates for multi-pollutant air remediation: promoting adhesion and activity by SiO2interlayers

In recent years, nanoparticles have come under close scrutiny for their possible health and environmental issues, making them less attractive for photocatalytic applications in air or water purification. Replacing free nano-powders with active and stable films is thus a fundamental step towards developing effective photocatalytic devices. Aluminum represents a cheap and technologically-relevant substrate, but its photocatalytic applications have been hampered by adhesion issues and metal ion diffusion within the photocatalytic layer. In this work, the use of silica interlayers is investigated as a strategy to promote adhesion, efficiency and reusability of TiO₂films deposited on aluminum plates. Films were prepared from stable titania sols to avoid the use of nano-powders. Aluminum substrates with different surface morphology were investigated and the role of the silica interlayer thickness was studied. Films were extensively characterized, studying their structure, morphology, optical properties, adhesion and hardness. Self-cleaning properties were studied with respect to their superhydrophilicity and ability to resist fouling via alkylsilanes. Photocatalytic degradation tests were carried out using both volatile organic compounds and NO_x, also in recycle tests. The presence of the silica interlayer proved crucial to promote the film robustness and photocatalytic activity. The substrate morphology determined the optimal interlayer thickness, especially in terms of the film reusability.

Columnar nitrogen-doped ZnO nanostructured thin films obtained through atomic layer deposition

The present study was aimed to develop nitrogen-doped nanostructured ZnO thin films. These films were produced in a sequential procedure involving the atomic layer deposition technique, and a hydrothermal process supported by microwave heating. Employing the atomic layer deposition technique, through self-limited reactions of diethylzinc (DEZn) and H₂O, carried out at 3.29 × 10^-4atm and 190 °C, a high-quality ZnO seed was grown on a Si (100) substrate, producing a textured film. In a second stage, columnar ZnO nanostructures were grown perpendicularly oriented to the silicon substrate on those films, using a solvothermal process in a microwave heating facility, employing Zn(NO₃)₂as zinc precursor, while hexamethylenetetramine (HMTA) was used to produce the bridging of Zn²⁺ions. The consequence of N-doping concentration on the physicochemical properties of ZnO thin films was studied. The manufactured films were structurally analyzed by scanning electron microscopy and x-ray diffraction. Also, x-ray photoelectron spectroscopy, Raman, and UV-vis spectroscopies were used to provide further insight on the effect of nitrogen doping. The N-doped films displayed textured wurtzite-like structures that changes their preferential growth from the (002) to the (100) crystallographic plane, apparently promoted by the increase of nitrogen precursor. It is also shown that nitrogen-doped films undergo a reduction in their bandgap, compared to ZnO. The methodology presented here provides a viable way to perform high-quality N-ZnO nanostructured thin films.

Novel Strategy for the Development of Antibacterial TiO2 Thin Film onto Polymer Substrate at Room Temperature

This work demonstrates a novel method to deposit an antibacterial TiO₂ thin film on a polymer substrate at room temperature. A combination of sol–gel and photon assistance was used in the experiment in order to avoid any thermal processes of thin film crystallization. The morphological photograph of samples indicated that the TiO₂ thin film was perfectly coated on the PVC substrate without any cracks or pinholes. Chemical analysis by EDS and XPS reported that the thin film consisted of titanium (Ti), oxygen (O), and carbon (C). The Raman spectrum proved that the thin film was the anatase phase of TiO₂ and, furthermore, that it was contaminated with carbon remaining from the photon assistance process. In addition, the optical band gap of the thin film was 3.35 eV, suggesting that the photocatalytic activity of TiO₂ should occur under UV-A radiation. The bacteria viability assay was examined using E. coli and S. typhimurium as indicator strains under UV-A irradiation (365 nm) at different times. The data from OD and CFU count revealed that >97% of bacteria were killed after 60 min of irradiation, and the bacteria were completely killed at 120 min for E. coli and 180 min for S. typhimurium.

Coating-free TiO2@β-SiC alveolar foams as a ready-to-use composite photocatalyst with tunable adsorption properties for water treatment

Coating-free TiO₂@β-SiC photocatalytic composite foams gathered within a ready-to-use shell/core alveolar medium the photocatalytically active TiO₂ phase and the β-SiC foam structure were prepared via a multi-step shape memory synthesis (SMS) replica method. They were fabricated following a sequential two-step carburization approach, in which an external TiC skin was synthesized at the surface of a β-SiC skeleton foam obtained from a pre-shaped polyurethane foam during a first carburization step. The adsorption behaviour of the shell/core TiO₂@β-SiC composite foams towards the Diuron pollutant in water was tuned by submitting the carbide foams to a final calcination treatment within the 550–700 °C temperature range. The controlled calcination step allowed (i) the selective oxidation of the TiC shell into a TiO₂ crystallite shell owing to the β-SiC resistance to oxidation and (ii) the amount of residual unreacted carbon in the foams to be tuned. The lower the calcination temperature, the more pronounced the adsorption profiles of the composites and the higher the Diuron amount removed by adsorption on the residual unreacted carbon. The ready-to-use TiO₂@β-SiC composite foams were active in the degradation of the Diuron pesticide, without any further post-synthesis immobilization or synthesis process at the foam surface. They displayed good reusability with test cycles and benefitted from an enhanced stability in terms of the titania release to water.

Coating-free TiO₂@β-SiC photocatalytic composite foams gathering within a ready-to-use shell/core alveolar medium the TiO₂ photocatalyst and the β-SiC foam structure were prepared via a multi-step shape memory synthesis (SMS) replica method.

Simultaneous removal of Cr(VI) and phenol contaminants using Z-scheme bismuth oxyiodide/reduced graphene oxide/bismuth sulfide system under visible-light irradiation

An all-solid-state Z-scheme system containing Bi-based semiconductors bismuth oxyiodide (BiOI) and bismuth sulfide (Bi₂S₃) was constructed on reduced graphene oxide (rGO) sheets through an electrostatic self-assembly method to simultaneously remove aqueous Cr(VI) and phenol. In this Z-scheme that mimicked natural photosynthesis, photoinduced electrons in the conduction band (CB) of BiOI were transferred through rGO and reacted with photoinduced holes in the valence band (VB) of Bi₂S₃, which significantly increased its photocatalytic activity. The reduction and oxidation reactions were performed on Bi₂S₃ and BiOI photocatalysts, respectively. Furthermore, complex contaminants of coexisting heavy metal Cr(VI) and organic phenol were treated using the system under visible-light irradiation. Results showed that Cr(VI) reduction and phenol oxidation were achieved efficiently with optimum reductive and oxidative efficiencies up to 73% and 95% under visible-light irradiation, respectively. This work provided a promising method of simultaneously removing heavy metals and organic pollutants by using a Z-scheme system with enhanced photocatalytic activity.

Nitrogen-containing organic compounds: Origins, toxicity and conditions of their photocatalytic mineralization over TiO2

Sustainable water management remains a global concern to meet the food needs of industrial and agricultural activities. Therefore, pollution abatement techniques, cheap and environmentally, are highly desired and recommended. The present review is devoted to the origin and the toxicity of nitrogen-containing organic compounds in water. The progress made in removing these pollutants, in recent years, is addressed. However, a prominent place is given to the photocatalytic degradation process using the TiO₂ as a semiconductor, the conditions for good mineralization and especially the factors influencing it. The parameters that impact the performance of this method are the pH, the temperature, the reactor used, the light, the concentration of the pollutant, the amount of catalyst, etc. Up to now, the importance of one parameter relative to another has not been established because in the context of the photocatalytic degradation, certain parameters are often tightly coupled. Consequently, the mineralization is dependent on the initial degree of oxidation of nitrogen atom contained in the pollutant to be degraded. The hydroxyl nitrogen is primarily converted into nitrate ions (NO₃^-), while the amides and the primary amines are converted into ammonium ions (NH₄⁺).