Comparative study of the photocatalytic activity for hydrogen evolution of MFe 2 O 4 (M = Cu, Ni) prepared by three different methods

Ba3(PO4)2 Photocatalyst for Efficient Photocatalytic Application

Barium phosphate (Ba3(PO4)2) is a class of material that has attracted significant attention thanks to its chemical stability and versatility. However, the use of Ba3(PO4)2 as a photocatalyst is scarcely reported, and its use as a photocatalyst has yet to be reported. Herein, Ba3(PO4)2 nanoflakes synthesis is optimized using sol-gel and hydrothermal methods. The as-prepared Ba3(PO4)2 powders are investigated using physicochemical characterizations, including XRD, SEM, EDX, FTIR, DRS, J-t, LSV, Mott-Schottky, and EIS. In addition, DFT calculations are performed to investigate the band structure. The oxidation capability of the photocatalysts is investigated depending on the synthesis method using rhodamine B (RhB) as a pollutant model. Both Ba3(PO4)2 samples prepared by the sol-gel and hydrothermal methods display high RhB photodegradation of 79% and 68%, respectively. The Ba3(PO4)2 obtained using the sol-gel process exhibits much higher stability under light excitation after four regeneration cycles. The photocatalytic oxidation mechanism is proposed based on the active species trapping experiments where O2 •‒ is the most reactive species. The finding shows the promising potential of Ba3(PO4)2 photocatalysts and opens the door for further investigation and application in various photocatalytic applications.

Removal of Organic Dyes from Water and Wastewater Using Magnetic Ferrite-Based Titanium Oxide and Zinc Oxide Nanocomposites: A Review

Heterogeneous photocatalysis using titanium dioxide (TiO2) and zinc oxide (ZnO) has been widely studied in various applications, including organic pollutant remediation in aqueous systems. The popularity of these materials is based on their high photocatalytic activity, strong photosensitivity, and relatively low cost. However, their commercial application has been limited by their wide bandgaps, inability to absorb visible light, fast electron/hole recombination, and limited recyclability since the nanomaterial is difficult to recover. Researchers have developed several strategies to overcome these limitations. Chief amongst these is the coupling of different semi-conductor materials to produce heterojunction nanocomposite materials, which are both visible-light-active and easily recoverable. This review focuses on the advances made in the development of magnetic ferrite-based titanium oxide and zinc oxide nanocomposites. The physical and magnetic properties of the most widely used ferrite compounds are discussed. The spinel structured material had superior catalytic and magnetic performance when coupled to TiO2 and ZnO. An assessment of the range of synthesis methods is also presented. A comprehensive review of the photocatalytic degradation of various priority organic pollutants using the ferrite-based nanocomposites revealed that degradation efficiency and magnetic recovery potential are dependent on factors such as the chemical composition of the heterojunction material, synthesis method, irradiation source, and structure of pollutant. It should be noted that very few studies have gone beyond the degradation efficiency studies. Very little information is available on the extent of mineralization and the subsequent formation of intermediate compounds when these composite catalysts are used. Additionally, potential degradation mechanisms have not been adequately reported.

Isolation Strategy towards Earth-Abundant Single-Site Co-Catalysts for Photocatalytic Hydrogen Evolution Reaction

Achieving efficient photocatalytic water splitting remains one of the most vital challenges in the photocatalysis field, as the performance of contemporary heterogeneous catalysts is still limited by their insufficient activity and low predictability. To address this challenge, this work takes inspiration from the concept of heterogeneous single-metal-site catalysts (HSMSCs) and follows the idea of site-isolation, aiming towards single-site co-catalyst species and a higher atom-utilization efficiency. We synthesized a set of photocatalysts through an adsorption-limited wet impregnation process using bare and phosphate-modified TiO2 as model supports and earth-abundant metals (Cu and Ni) with various loadings (0.008–5 wt.%) as co-catalyst species. The catalysts are characterized by TXRF for the determination of the real co-catalyst loadings, UV-vis and FTIR spectroscopes for semi-quantitative analysis of the metal state and binding modes to the substrate, and HRTEM for resolving the morphology of the sample’s surface. All samples were then evaluated towards the photocatalytic hydrogen evolution reaction (HER). We show that much higher turnover frequencies (TOFs) are obtained for both Cu- and Ni-based systems when lower co-catalyst loadings are used, which indicates an improved atom-utilization efficiency that reaches performances comparable to the noble Au co-catalyst. We also introduce a structural model to explain the observed TOF trends, which confirms that both earth-abundant systems undergo a strong structural reconstruction upon site-isolation towards smaller, perhaps even single-site-like species.

A critical review on advances in the practices and perspectives for the treatment of dye industry wastewater

Rapid industrialization has provided comforts to mankind but has also impacted the environment harmfully. There has been severe increase in the pollution due to several industries, in particular due to dye industry, which generate huge quantities of wastewater containing hazardous chemicals. Although tremendous developments have taken place for the treatment and management of such wastewater through chemical or biological processes, there is an emerging shift in the approach, with focus shifting on resource recovery from such wastewater and also their management in sustainable manner. This review article aims to present and discuss the most advanced and state-of-art technical and scientific developments about the treatment of dye industry wastewater, which include advanced oxidation process, membrane filtration technique, microbial technologies, bio-electrochemical degradation, photocatalytic degradation, etc. Among these technologies, microbial degradation seems highly promising for resource recovery and sustainability and has been discussed in detail as a promising approach. This paper also covers the challenges and future perspectives in this field.

Photocatalytic degradation and kinetic modeling of azo dye using bimetallic photocatalysts: effect of synthesis and operational parameters

Industrial wastewaters are the major source polluting the surface and ground water resources. Pollutants released along with the untreated textile industry wastewaters are responsible for the great damage to the natural resources like water. Considering the hazardous effects of the azo dyes (textile coloring agents) and their byproducts, there is a need to develop cost-effective and efficient treatment method for the textile wastewaters as such dyes have been reported as toxic, mutagenic, and carcinogenic and can cause direct demolition of aquatic communities. One of the possible and effective treatment methods is the use of TiO₂ photocatalysis due to its chemical stability, low cost, and non-toxic nature. The present study explored the photocatalytic potential of anatase-type of bimetallic Cu-Ni/TiO₂ photocatalysts under visible light irradiation for possible photocatalytic degradation and mineralization of Methyl Orange (MO), as model azo dye. The focus was to correlate the synthesis (different calcination temperatures, phase composition of TiO₂ either anatase or rutile, and metal ion loading in terms of concentration and composition (Cu:Ni)) and operational parameters (photocatalyst loading, pollutant concentration, and irradiation time) that were believed responsible for the enhanced photocatalytic performance. Blank experiments were carried out to check the effect of metal loading in comparison to bare TiO₂ and effect of absence or presence of light and photocatalysts on MO photodegradation. Results obtained using bimetallic photocatalysts are promising as compared to bare TiO₂ as 100% MO removal and ~ 90% %COD removal were obtained in 90 min of irradiation, obeying a pseudo-first-order kinetics with photocatalytic reaction via the Langmuir-Hinshelwood mechanism with a good linear fit. Photocatalysts synthesized using anatase TiO₂ were reported with improved performance compared to rutile phase. It is evident that synthesis parameters influence photocatalyst performance directly. The higher rate constant (> 1) that proves the excellent adsorption capacity of the tested photocatalysts for tested pollutants on the surface may have a great prospective for photocatalytic water purification at neutral pH.