Anatomic reconstruction of acromioclavicular joint dislocations using allograft and synthetic ligament

Anatomical acromioclavicular joint stabilization with chemically sterilized tendon allografts: A retrospective study

Background

The purpose of this retrospective study was to analyze whether chemically sterilized tendon allografts perform as well as other non-sterilized allografts and autografts as described in the literature for anatomical acromioclavicular joint stabilization for the treatment of Rockwood III-V. Allografts are still described as a factor for higher re-rupture rates.

Methods

Retrospective data were collected from 21 acromioclavicular joint stabilizations performed by a single surgeon and performed between 2011 and 2014 using sterilized semitendinosus allografts. The primary endpoints were re-rupture and complication rates. Secondary endpoints were AC-joint stability, pain level, return to work and sport and the range of motion.

Results

No re-ruptures occurred during the mean follow-up time of 33 months. Zero complications occurred directly after surgery, but three complications later than three weeks after surgery. All cases resolved without further surgery. After surgery, stability significantly improved for all patients. Post-surgery, 19 patients had stable acromioclavicular joints and only two patients showed minor instabilities. Range of motion returned to the range of the healthy shoulders for all patients.

Conclusion

Chemically sterilized semitendinosus allograft use for anatomic AC-joint stabilization is equivalent to the use of other allografts or autografts and required no hardware removal. No donor age or graft size dependence was observed, due to zero re-ruptures.

Bone tunnel placement influences shear stresses at the coracoid process after coracoclavicular ligament reconstruction: a finite element study and radiological analysis

INTRODUCTION

Coracoid fractures after arthroscopic treatment of acromioclavicular (AC) joint separations lead to poor clinical outcomes. In this study, different configurations of bone tunnels in the lateral clavicle and coracoid were examined concerning the amount of stress induced in the coracoid.

METHODS

An authentic 3D finite element model of an ac joint was established. Three 2.4 mm bone tunnels were inserted in the lateral clavicle, which were situated above, medially and laterally of the coracoid. Then, two 2.4 mm bone tunnels were inserted in the latter, each simulating a proximal and a distal suture button position. Von Mises stress analyses were performed to evaluate the amount of stress caused in the coracoid process by the different configurations. Then, a clinical series of radiographs was examined, the placement of the clavicle drill hole was analyzed and the number of dangerous configurations was recorded.

RESULTS

The safest configuration was a proximal tunnel in the coracoid combined with a lateral bone tunnel in the clavicle, leading to an oblique traction at the coracoid. A distal bone tunnel in the coracoid and perpendicular traction as well as a proximal tunnel in the coracoid with medial traction caused the highest stresses. Anatomical placement of the clavicle drill hole does lead to configurations with smaller stresses.

CONCLUSION

The bone tunnel placement with the smallest amount of shear stresses was found when the traction of the suture button was directed slightly lateral, towards the AC joint. Anatomical placement of the clavicle drill hole alone was not sufficient in preventing dangerous configurations.

LEVEL OF EVIDENCE

Controlled laboratory study.

ANATOMICAL AND BIOMECHANICAL ROLE OF STATIC STABILIZERS OF THE ACROMIOCLAVICULAR JOINT

OBJECTIVE

The aim: To determine the anatomical and biomechanical significance of the static stabilizers of the acromioclavicular joint by conducting numerical modeling using the finite element method and experimental investigation.

PATIENTS AND METHODS

Materials and methods: To ensure the study, modeling of the deformation processes of the clavicle and scapula systems with various combinations of ligament damage was conducted. The COMPAS-3D software package was used to build the simulation model, which allowed obtaining models that are closest to reality. To verify the results of the numerical modeling, corresponding studies of the mechanical characteristics and determination of the stiffness of the investigated systems were carried out using the upgraded TIRAtest-2151 testing stand.

RESULTS

Results: The stiffest system is the system in which all ligaments are intact, and the sequence of decreasing stiffness of the system is presented in the following order: damage to lig. trapezoideum; lig. conoideum; lig. claviculo-acoacromiale inferior; lig. claviculo-acoacromiale superior; the coracoclavicular ligament complex; the acromioclavicular ligament complex.

CONCLUSION

Conclusions: Static stabilizers in general, and their components in particular, are characterized by significant anatomical and functional features. The natural stabilization of the acromioclavicular joint is provided by their synergistic interaction, which is the basis for the development and implementation of surgical interventions, the scope of which includes the restoration of both ligament complexes. The loss of stiffness in the «clavicle-scapula» system is significantly more pronounced when lig. acromioclaviculare superior and inferior are damaged (8.5 N/mm) than when lig. conoideum and lig. trapezoideum are damaged (11.6 N/mm).