Biomechanical Evaluation of a Growth-Friendly Rod Construct

A novel spine tester TO GO

Background

Often after large animal experiments in spinal research, the question arises-histology or biomechanics? While biomechanics are essential for informed decisions on the functionality of the therapy being studied, scientists often choose histological analysis alone. For biomechanical testing, for example, flexibility, specimens must be shipped to institutions with special testing equipment, as spine testers are complex and immobile. The specimens must usually be shipped frozen, and, thus, biological and histological investigations are not possible anymore. To allow both biomechanical and biological investigations with the same specimen and, thus, to reduce the number of required animals, the aim of the study was to develop a spine tester that can be shipped worldwide to test on-site.

Methods

The "Spine Tester TO GO" was designed consisting of a frame with three motors that initiate pure moments and rotate the specimen in three motion planes. A load cell and an optical motion tracking system controlled the applied loads and measured range of motion (ROM) and neutral zone (NZ). As a proof of concept, the new machine was validated and compared under real experimental conditions with an existing testing machine already validated employing fresh bovine tail discs CY34 (n = 10).

Results

The new spine tester measured reasonable ROM and NZ from hysteresis curves, and the ROM of the two testing machines formed a high coefficient of determination R 2 = 0.986. However, higher ROM results of the new testing machine might be explained by the lower friction of the air bearings, which allowed more translational motion.

Conclusions

The spine tester TO GO now opens up new opportunities for on-site flexibility tests and contributes hereby to the 3R principle by limiting the number of experimental animals needed to obtain full characterization of spine units at the macroscopic, biomechanical, biochemical, and histological level.

Serum Titanium Levels Remain Elevated But Urine Titanium is Undetectable in Children With Early Onset Scoliosis Undergoing Growth-Friendly Surgical Treatment: A Prospective Study

BACKGROUND

Elevated serum titanium levels have been found in patients with early onset scoliosis (EOS) treated with traditional growing rods (TGR), magnetically controlled growing rods (MCGR), and vertical expandable prosthetic titanium rib (VEPTR). No studies have investigated whether serum titanium remains persistently elevated and if titanium is excreted. Our purpose was to compare serum titanium levels in patients with EOS with growth-friendly instrumentation to age-matched controls and evaluate urine titanium and serial serum titanium levels in patients with EOS.

METHODS

This was a prospective case-control study. Patients with EOS with TGR, MCGR, or VEPTR underwent urine titanium and serial serum titanium collection at a minimum 6-month interval. Control patients did not have a history of metal implant insertion and underwent serum titanium collection before fracture fixation.

RESULTS

Twenty patients with EOS (6 TGR, 8 MCGR, and 6 VEPTR) and 12 controls were analyzed. The control group had no detectable serum titanium (0 ng/mL), whereas the patients with EOS had a median serum titanium of 4.0 ng/mL ( P < 0.001). Analysis of variance showed significantly higher median serum titanium levels in the MCGR and VEPTR groups than the TGR group at time point 1 (5.5 vs 6.0 vs 2.0 ng/mL, P = 0.01) and time point 2 (6.5 vs 7.5 vs 2.0 ng/mL, P < 0.001). Binary comparisons showed a significant difference in serum titanium level between TGR and MCGR (time point 1: P = 0.026, time point 2: P = 0.011) and TGR and VEPTR (time point 1: P = 0.035, time point 2: P = 0.003). However, there was no difference between MCGR and VEPTR (time point 1: P = 0.399, time point 2: P = 0.492) even though the VEPTR group had a longer duration of follow-up ( P = 0.001) and a greater number of lengthenings per patient at the first serum collection ( P = 0.016). No patients with EOS had detectable urine titanium.

CONCLUSIONS

Patients with EOS treated with titanium alloy growth-friendly instrumentation had elevated serum titanium levels compared with age-matched controls that persisted over time with no evidence of renal excretion. Additional studies are necessary to assess for local and systemic accumulation of titanium and the significance of long-term exposure to titanium in growing children.

LEVEL OF EVIDENCE

Level III, therapeutic.

Mechanical Analysis of 3 Posterior Fusion Assemblies Intended to Cross the Cervicothoracic Junction

STUDY DESIGN

This was a biomechanical comparison study.

OBJECTIVE

The objective of this study is to evaluate the mechanical properties of 3 posterior spinal fusion assemblies commonly used to cross the cervicothoracic junction.

SUMMARY OF BACKGROUND

When posterior cervical fusions are extended into the thoracic spine, an instrumentation transition is often utilized. The cervical rod (3.5 mm) can continue using thoracic screws designed to accept the cervical rods. Alternatively, traditional thoracic screws may be used to accept thoracic rods (5.5 mm). This requires the use of a 3.5-5.5 mm transition rod or a separate 5.5 mm rod and a connector to fix the 3.5 and 5.5 mm rod together. Fusion success depends on the immobilization of vertebrae, yet the mechanics provided by these different assemblies are unknown.

MATERIALS AND METHODS

Three titanium alloy posterior fusion assemblies intended to cross the cervicothoracic junction underwent static compressive bending, tensile bending, and torsion as described in ASTM F1717 to a torque of 2.5 Nm. Five samples of each assembly were attached to ultrahigh molecular weight polyethylene blocks via multiaxial screws for testing. Force and displacement were recorded, and the stiffness of each construct was calculated.

RESULTS

The 2 assemblies that included a 5.5 mm rod were found to be stiffer and have less range of motion than the assembly that used only 3.5 mm rods.

CONCLUSIONS

The results of this study indicate that incorporating a 5.5 mm rod in a fusion assembly adds significant stiffness to the construct. When the stability of a fusion is of heightened concern, as demonstrated by the ASTM F1717 vertebrectomy (worst-case scenario) model, including 5.5 mm rods may increase fusion success rates.

LEVEL OF EVIDENCE

Level V.

Analysis of serum levels of titanium and aluminium ions in patients with early onset scoliosis operated upon using the magnetic growing rod-a single centre study of 14 patients

STUDY DESIGN

A cross-sectional retrospective Level 3 study.

OBJECTIVE

To study the serum levels of Titanium and Aluminium ions in patients operated using the magnetically controlled growing rod (MCGR) system. 14 consecutive patients of early onset scoliosis with varying etiology managed with MCGR system with a minimum follow-up of 24 months were selected for the study. The group consisted of two boys (14.3%) and 12 girls (85.7%). The average age of the patients at the time of surgery was 10.4 years (5-15 years). The average period of follow-up was 43.7 months (28-79 months). After informed consent of the subjects and their caretakers, serum levels of titanium and aluminium were measured. These levels were then assessed with regards to the number of screws used, number of distractions and complications.

METHODS

The concentration of titanium and aluminium ions in the serum was measured using high resolution inductively coupled plasma mass spectrometry.

RESULTS

For the sake of ease of assessment, patients were divided into three etiology-based groups-idiopathic (n = 6), neuromuscular (n = 2) and syndromic (n = 6). The mean serum titanium level was 15.9 μg/L (5.1-28.2 μg/L) while that of aluminium was 0.1 μmol/L (0.1-0.2 μmol/L). Of the 14 patients, 2 (14.2%) patients had mechanical failure (actuator pin dysfunction), 3 (21.4%) had rod breakage requiring revision surgery and one patient (7.1%) had surgical site infection managed with appropriate antibiotics. Patients undergoing revision for rod breakage did not show any metallosis of the tissues during surgery.

CONCLUSION

Analysis of patients with scoliosis operated using the magnetic growing rod system concludes that it is accompanied by presence of titanium in the blood but whether clinically significant or not needs to be ascertained by comparison of preoperative and postoperative blood concentrations of the titanium ions in individual subjects. The aluminium ion concentration remains within normal limits. Though implant malfunction may raise the titanium levels in the blood, its clinical significance needs to be determined. The aluminium levels are not affected irrespective to the presence or absence of complications. The long-term effects of raised titanium levels in the blood also warrant further prospective studies designed for precise and deeper analyses.

Validation of a custom spine biomechanics simulator: A case for standardization

Mechanical testing machines used in cadaveric spine biomechanics research vary between labs. It is a necessary first step to understand the capabilities and limitations in any testing machine prior to publishing experimental data. In this study, a reproducible protocol that uses a synthetic spine was developed and used to quantify the inherent rotation error and the ability to apply loads in a single physiologic plane (pure-moment) of a custom spine biomechanics simulator. Rotation error was evaluated by comparing data collected by the test machine and the data collected by an optical motion capture system. Pure-moment loading was assessed by comparing the out-of-plane loads to the primary plane load. Using synthetic functional spine units previously shown to have mechanics similar to the cadaveric human spine, the simulator was evaluated using a dynamic test protocol reflective of its future use in the study of cadaveric spine specimens. Rotation errors inherent in the test machine were <0.25° compared to motion capture. Out of plane loads were <4.0% of the primary plane load, which confirmed pure-moment loading. The authors suggest that a standard validation protocol for biomechanical spine testing machines is needed for transparency and accurate field-wide data interpretation and comparison. We offer recommendations based on the reproducible use of a synthetic spinal specimen for consideration.

Early-onset Scoliosis: Contemporary Decision-making and Treatment Options

Early-onset scoliosis (EOS) describes a wide array of diagnoses and deformities exposed to growth. This potentially life-threatening condition is still 1 of the biggest challenges in pediatric orthopaedics. The enlightenment of Bob Campbell's thoracic insufficiency syndrome concept and the negative impact of the earlier short and straight spine fusion approach on respiratory function and survival have fueled the evolution of EOS care. Despite all the progress made, growth-friendly spine surgery remains to be a burden to patients and caregivers. Even down-sized implants and remote-controlled noninvasive rod expansions do not omit unexpected returns to the operating room: failures of foundations, rod breakage, difficulties to keep the sagittal balance, progressive transverse plane deformities, stiffening, and the need for final instrumented fusion are still common. However, past experience and the current multitude of surgical strategies and implants have sharpened the decision-making process, patients with thoracic insufficiency syndrome require earliest possible vertical expandable prosthetic titanium ribs application. Flexible deformities below 60 degrees, with normal spinal anatomy and without thoracic involvement, benefit from serial Mehta casting which revived as a long available but not-used strategy. In case of progression, standard double growing rods or-if available, affordable, and applicable-magnetically controlled motorized rods provide deformity control and growth promotion. Shilla growth-guiding technique is a less costly alternative. Its lack of stiff lengthening boxes or actuators may be beneficial in difficult deformities. Anterior convex flexible tethering promises benefits of sparing the trunk muscles and keeping mobility. However, this step towards a true nonfusion concept has yet to stand the test of broad clinical application.

Metal Ion Release During Growth-Friendly Instrumentation for Early-Onset Scoliosis: A Preliminary Study

BACKGROUND

Metal ions released from spinal instruments can cause localized debris and distribute systemically to settle on distant organs. Children with early-onset deformities live with metallic implants for a substantial amount of time. No research focused on metal distribution in growth-friendly instrumentations. The aim of this study was to compare age-matched growing rod (GR) and magnetically controlled growing rod (MCGR) groups to noninstrumented controls.

METHODS

The study was designed as a multicenter, prospective, cross-sectional case series. GR and MCGR applications of three institutions were included. A total of 52 children were enrolled. Blood samples were collected between December 2014 and February 2015. Biochemical serum analyses were performed to trace and quantify titanium, vanadium, aluminum, and boron. The GR group included 15 children. Mean age was 10.7 (range 6-15). MCGR group included 22 children. Mean age was 8.5 (range 2-13). Fifteen age-matched nonoperated children formed the control group. The mean age was 10.4 (range 5-15). One-way analysis of variance, Kruskal-Wallis, and Mann-Whitney U tests were used for comparisons.

RESULTS

The mean serum titanium level in control, GR, and MCGR groups were 2.8 ± 1.4, 7.3 ± 4.3, and 10.2 ± 6.8 μg/L, respectively. GR and MCGR group titanium levels were higher than controls' (p = .008 and p < .001). The mean serum vanadium level in control, GR, and MCGR groups were 0.2 ± 0.0, 0.2 ± 0.0, and 0.5 ± 0.5 μg/L, respectively. MCGR group vanadium level was higher than control (p < .001) and GR groups (p = .004). Mean serum levels in control, GR, and MCGR groups were, respectively, 5.4 ± 4.1, 8.1 ± 7.4, and 7.8 ± 5.1 μg/L for aluminum and 86.7 ± 2.7, 86.9 ± 2.5, and 85.0 ± 6.6 μg/L for boron. The distribution of aluminum and boron were similar across groups (p = .675 and p = .396).

CONCLUSIONS

Both GR and MCGR applications significantly release titanium and possibly aluminum. MCGR further releases vanadium. MCGR possibly releases more titanium than traditional GR. Time-dependent alterations of serum ion levels, structural properties of the MCGR device, and exposure caused by magnetic distraction processes warrant investigation.

The rib cage reduces intervertebral disc pressures in cadaveric thoracic spines by sharing loading under applied dynamic moments

The effects of the rib cage on thoracic spine loading are not well studied, but the rib cage may provide stability or share loads with the spine. Intervertebral disc pressure provides insight into spinal loading, but such measurements are lacking in the thoracic spine. Thus, our objective was to examine thoracic intradiscal pressures under applied pure moments, and to determine the effect of the rib cage on these pressures. Human cadaveric thoracic spine specimens were positioned upright in a testing machine, and Dynamic pure moments (0 to ±5 N·m) with a compressive follower load of 400 N were applied in axial rotation, flexion - extension, and lateral bending. Disc pressures were measured at T4-T5 and T8-T9 using needle-mounted pressure transducers, first with the rib cage intact, and again after the rib cage was removed. Changes in pressure vs. moment slopes with rib cage removal were examined. Pressure generally increased with applied moments, and pressure-moment slope increased with rib cage removal at T4-T5 for axial rotation, extension, and lateral bending, and at T8-T9 for axial rotation. The results suggest the intact rib cage carried about 62% and 56% of axial rotation moments about T4-T5 and T8-T9, respectively, as well as 42% of extension moment and 36-43% of lateral bending moment about T4-T5 only. The rib cage likely plays a larger role in supporting moments than compressive loads, and may also play a larger role in the upper thorax than the lower thorax.