Structure and electron density analysis of electrochemically and chemically delithiated LiCoO2 single crystals

Structural Understanding for High-Voltage Stabilization of Lithium Cobalt Oxide

The rapid development of modern consumer electronics is placing higher demands on the lithium cobalt oxide (LiCoO2 ; LCO) cathode that powers them. Increasing operating voltage is exclusively effective in boosting LCO capacity and energy density but is inhibited by the innate high-voltage instability of the LCO structure that serves as the foundation and determinant of its electrochemical behavior in lithium-ion batteries. This has stimulated extensive research on LCO structural stabilization. Here, it is focused on the fundamental structural understanding of LCO cathode from long-term studies. Multi-scale structures concerning LCO bulk and surface and various structural issues along with their origins and corresponding stabilization strategies with specific mechanisms are uncovered and elucidated at length, which will certainly deepen and advance the knowledge of LCO structure and further its inherent relationship with electrochemical performance. Based on these understandings, remaining questions and opportunities for future stabilization of the LCO structure are also emphasized.

A synergetic promotion of surface stability for high-voltage LiCoO2 by multi-element surface doping: a first-principles study

The utilization of high-voltage LiCoO2 is an effective approach to break through the bottleneck of practical energy density in lithium ion batteries. However, the structural and interfacial degradations at the deeply delithiated state as well as the associated safety concerns impede the application of high-voltage LiCoO2. Herein, we present a synergetic strategy for promoting the surface stability of LiCoO2 at high voltage by Ti-Mg-Al co-doping and systematically study the effects of the dopants on the surface stability, electronic structure and Li+ diffusion properties of the LiCoO2 (104) surface using first-principles calculations. It is found that Ti, Mg and Al dopants can be facilely introduced into the Co sites of the LiCoO2 (104) surface. Furthermore, the co-doping could significantly stabilize the surface oxygen of LiCoO2 at a high delithiation state. Particularly, by aggregating Ti-Mg-Al co-dopant distribution in the surface layer, surface oxygen loss is dramatically suppressed. In addition, analysis of the electronic structure indicates that Ti-Mg-Al co-doping can enhance the electronic conductivity of the LiCoO2 (104) surface and greatly inhibit the charge deficiency of the superficial lattice O atoms at a highly delithiated state. In spite of a negligible improvement in the surface Li+ diffusion kinetics, the Ti-Mg-Al surface-modified LiCoO2 is expected to exhibit improved electrochemical performance at high voltage due to its superior surface stability. Our results suggest that aggregating Ti, Mg and Al co-dopant distribution in the surface layer is a promising modulation strategy to synergistically promote the surface oxygen stability of LiCoO2 at high voltages.

Impact of Synthesis Chelation on the Crystallography and Capacity of Li-Rich Li1.2Ni0.13Mn0.54Fe0.13O2 Cathode Particles

The quest for removal of cobalt from battery materials has intensified in the face of intensifying demand for batteries. Cobalt-free lithium-rich Li_1.2Ni_0.13Mn_0.54Fe_0.13O₂ (LNMFO) is synthesized under variation of chelating agent ratio and pH using the sol-gel method. Systematic search of the chelation and pH space found that the extractable capacity of the synthesized LNMFO is most clearly correlated to the ratio of chelating agent to transition metal oxide; a ratio of transition metal to citric acid of 2:1 achieves greater capacity at the expense of relative capacity retention. Charge-discharge cycling, dQ/dV analysis, XRD, and Raman at different charging potentials are used to quantify the different degrees of activation of the Li₂MnO₃ phase in the LNMFO powders synthesized under different chelation ratios. SEM and HRTEM analysis are employed to understand the effect of particle size and crystallography on the activation of Li₂MnO₃ phase in the composite particles. An unprecedented use of the marching cube algorithm to evaluate atomic scale tortuosity of crystallographic planes in HRTEM revealed that subtle undulations in the planes in addition to stacking faults correlate to the extracted capacity and stability of the various LNMFO synthesized.

Stress Prediction of the Particle Structure of All-Solid-State Batteries by Numerical Simulation and Machine Learning

All-Solid-state batteries (ASSBs) are non-flammable and safe and have high capacities. Thus, ASSBs are expected to be commercialized soon for use in electric vehicles. However, because the electrode active material (AM) and solid electrolyte (SE) of ASSBs are both solid particles, the contact between the particles strongly affects the battery characteristics, yet the correlation between the electrode structure and the stress at the contact surface between the solids remains unknown. Therefore, we used the results of numerical simulations as a dataset to build a machine learning model to predict the battery performance of ASSBs. Specifically, the discrete element method (DEM) was used for the numerical simulations. In these simulations, AM and SE particles were used to fill a model of the electrode, and force was applied from one direction. Thus, the stress between the particles was calculated with respect to time. Using the simulations, we obtained a sufficient data set to build a machine learning model to predict the distribution of interparticle stress, which is difficult to measure experimentally. Promisingly, the stress distribution predicted by the constructed machine learning model showed good agreement with the stress distribution calculated by DEM.

A multi-technique approach to understanding delithiation damage in LiCoO2 thin films

We report on the delithiation of LiCoO₂ thin films using oxalic acid (C₂H₂O₄) with the goal of understanding the structural degradation of an insertion oxide associated with Li chemical extraction. Using a multi-technique approach that includes synchrotron radiation X-ray diffraction, scanning electron microscopy, micro Raman spectroscopy, photoelectron spectroscopy and conductive atomic force microscopy we reveal the balance between selective Li extraction and structural damage. We identify three different delithiation regimes, related to surface processes, bulk delithiation and damage generation. We find that only a fraction of the grains is affected by the delithiation process, which may create local inhomogeneities. However, the bulk delithiation regime is effective to delithiate the LCO film. All experimental evidence collected indicates that the delithiation process in this regime mimics the behavior of LCO upon electrochemical delithiation. We discard the formation of Co oxalate during the chemical extraction process. In conclusion, the chemical route to Li extraction provides additional opportunities to investigate delithiation while avoiding the complications associated with electrolyte breakdown and simplifying in-situ measurements.

Electrodeposition Technologies for Li-Based Batteries: New Frontiers of Energy Storage

Electrodeposition induces material syntheses on conductive surfaces, distinguishing it from the widely used solid-state technologies in Li-based batteries. Electrodeposition drives uphill reactions by applying electric energy instead of heating. These features may enable electrodeposition to meet some needs for battery fabrication that conventional technologies can rarely achieve. The latest progress of electrodeposition technologies in Li-based batteries is summarized. Each component of Li-based batteries can be electrodeposited or synthesized with multiple methods. The advantages of electrodeposition are the main focus, and they are discussed in comparison with traditional technologies with the expectation to inspire innovations to build better Li-based batteries. Electrodeposition coats conformal films on surfaces and can control the film thickness, providing an effective approach to enhancing battery performance. Engineering interfaces by electrodeposition can stabilize the solid electrolyte interphase (SEI) and strengthen the adhesion of active materials to substrates, thereby prolonging the battery longevity. Lastly, a perspective of future studies on electrodepositing batteries is provided. The significant merits of electrodeposition should greatly advance the development of Li-based batteries.

Probing transport limitations in thick sintered battery electrodes with neutron imaging

Lithium-ion batteries have received significant research interest due to their advantages in energy and power density, which are important to enabling many devices. One route to further increase energy density is to fabricate thicker electrodes in the battery cell; however, careful consideration must be taken when designing electrodes as to how increasing the thickness impacts the multiscale and multiphase molecular transport processes, which can limit the overall battery operating power. Design of these electrodes necessitates probing the molecular processes when the battery cell undergoes electrochemical charge/discharge. One tool for in situ insights into the cell is neutron imaging, because neutron imaging can provide information of where electrochemical processes occur within the electrodes. In this manuscript, neutron imaging is applied to track the lithiation/delithiation processes within electrodes at different current densities for a full cell with a thick sintered Li₄Ti₅O₁₂ anode and LiCoO₂ cathode. The neutron imaging reveals that the molecular distribution of Li⁺ during discharge within the electrode is sensitive to the current density, or equivalently discharge rate. An electrochemical model provides additional insights into the limiting processes occurring within the electrodes. In particular, the impact of tortuosity and molecular transport in the liquid phase within the interstitial regions in the electrodes are considered, and the influence of tortuosity was shown to be highly sensitive to the current density. Qualitatively, the experimental results suggest that the electrodes behave consistent with the packed hard sphere approximation of Bruggeman tortuosity scaling, which indicates that the electrodes are largely mechanically intact but also that a design that incorporates tunable tortuosity could improve the performance of these types of electrodes.

Interaction of Phosphate with Lithium Cobalt Oxide Nanoparticles: A Combined Spectroscopic and Calorimetric Study

Adsorption of small ions such as phosphates to the surfaces of metal oxides can significantly alter the behavior of these materials, especially when present in the nanoscale form. Lithium cobalt oxide is a good model system for understanding small-molecule interactions with emerging nanomaterials because of its widespread use in lithium ion batteries and its known activity as a water oxidation catalyst. Here, we present a thermodynamic analysis of phosphate adsorption to LiCoO₂ and corroborate the results with additional in situ techniques, including zeta potential measurements and attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy, at pH values relevant to potential environmental release scenarios. Flow microcalorimetry measurements of phosphate interaction with LiCoO₂ at pH 7.4 show that there are two distinct exothermic processes taking place. Time-sequence in situ ATR-FTIR with two-dimensional correlation analysis reveals the spectroscopic signatures of these processes. We interpret the data as an interaction of phosphate with LiCoO₂ that occurs through the release of two water molecules and is therefore, best described as a condensation process rather than a simple adsorption, consistent with prior studies, demonstrating that phosphate interaction with LiCoO₂ is highly irreversible. Additional measurements for over longer times of 5 months show that phosphate adsorption terminates with one surface layer and that continued transformation over longer periods of time arises from H⁺/Li⁺ exchange and slow transformation to a cobalt hydroxide, with phosphate adsorbed to the surface only. To the best of our knowledge, this is the first time that flow microcalorimetry and two-dimensional correlation spectroscopy have been applied in tandem to clarify the specific chemical reactions that occur at the interface of solids and adsorbates.

Monitoring the evolution of local oxygen environments during LiCoO2 charging via ex situ17O NMR

A Li_xCoO₂ phase diagram based on NMR results in reference to different phase regions derived from the dV/dx vs. x plot.

A sustainable process for metal recycling from spent lithium-ion batteries using ammonium chloride

In this paper, a sustainable process to recover valuable metals from spent lithium ion batteries (LIBs) in sulfuric acid using ammonium chloride as reductant was proposed and studied. Being easily reused, ammonium chloride is found to be efficient and posing minor environmental impacts during the overall process. By investigating the effects of a wide range of parameters, e.g., H₂SO₄ concentration, NH₄Cl concentration, temperature, leaching time, and solid-to-liquid mass ratio, the leaching behaviour of Li, Ni, Co, and Mn was systematically investigated. And the leaching mechanism and kinetics were determined by mineralogically characterization of residues at various reaction times and by fitting using different kinetic models. With this research, it is possible to provide a win-win solution to improve the recycling effectiveness of spent LIBs by using waste salt that is easily reused as the reductant.

Solid-state electrochemistry on the nanometer and atomic scales: the scanning probe microscopy approach

Energy technologies of the 21(st) century require an understanding and precise control over ion transport and electrochemistry at all length scales - from single atoms to macroscopic devices. This short review provides a summary of recent studies dedicated to methods of advanced scanning probe microscopy for probing electrochemical transformations in solids at the meso-, nano- and atomic scales. The discussion presents the advantages and limitations of several techniques and a wealth of examples highlighting peculiarities of nanoscale electrochemistry.

Oxyanion induced variations in domain structure for amorphous cobalt oxide oxygen evolving catalysts, resolved by X-ray pair distribution function analysis

Amorphous thin film oxygen evolving catalysts, OECs, of first-row transition metals show promise to serve as self-assembling photoanode materials in solar-driven, photoelectrochemical `artificial leaf' devices. This report demonstrates the ability to use high-energy X-ray scattering and atomic pair distribution function analysis, PDF, to resolve structure in amorphous metal oxide catalyst films. The analysis is applied here to resolve domain structure differences induced by oxyanion substitution during the electrochemical assembly of amorphous cobalt oxide catalyst films, Co-OEC. PDF patterns for Co-OEC films formed using phosphate, Pi, methylphosphate, MPi, and borate, Bi, electrolyte buffers show that the resulting domains vary in size following the sequence Pi < MPi < Bi. The increases in domain size for CoMPi and CoBi were found to be correlated with increases in the contributions from bilayer and trilayer stacked domains having structures intermediate between those of the LiCoOO and CoO(OH) mineral forms. The lattice structures and offset stacking of adjacent layers in the partially stacked CoMPi and CoBi domains were best matched to those in the LiCoOO layered structure. The results demonstrate the ability of PDF analysis to elucidate features of domain size, structure, defect content and mesoscale organization for amorphous metal oxide catalysts that are not readily accessed by other X-ray techniques. PDF structure analysis is shown to provide a way to characterize domain structures in different forms of amorphous oxide catalysts, and hence provide an opportunity to investigate correlations between domain structure and catalytic activity.

Zero-strain reductive intercalation in a molecular framework

Reductive intercalation of potassium within the molecular framework Ag3[Fe(CN)6] gives rise to a volume strain that is an order of magnitude smaller than is typical for common ion-storage materials. We suggest that framework flexibility might be exploited as a general strategy for reducing cycling strain in battery and ion-storage materials.

Chemical delithiation and exfoliation of [Formula: see text]

Progressive chemical .delithiation of commercially available lithium cobalt oxide ([Formula: see text]) showed consecutive changes in the crystal properties. Rietveld refinement of high resolution X-ray and neutron diffraction revealed an increased lattice parameter c and a reduced lattice parameter a for chemically delithiated samples. Using electron microscopy we have also followed the changes in the texture of the samples towards what we have found is a critical layer stoichiometry of about [Formula: see text] with x=1/3 that causes the grains to exfoliate. The pattern of etches by delithiation suggests that unrelieved strain fields may produce chemical activity.

Preparation and characterization of core-shell battery materials for Li-ion batteries manufactured by substrate induced coagulation

In this work Substrate Induced Coagulation (SIC) was used to coat the cathode material LiCoO(2), commonly used in Li-ion batteries, with fine nano-sized particulate titania. Substrate Induced Coagulation is a self-assembled dip-coating process capable of coating different surfaces with fine particulate materials from liquid media. A SIC coating consists of thin and rinse-prove layers of solid particles. An advantage of this dip-coating method is that the method is easy and cheap and that the materials can be handled by standard lab equipment. Here, the SIC coating of titania on LiCoO(2) is followed by a solid-state reaction forming new inorganic layers and a core-shell material, while keeping the content of active battery material high. This titania based coating was designed to confine the reaction of extensively delithiated (charged) LiCoO(2) and the electrolyte. The core-shell materials were characterized by SEM, XPS, XRD and Rietveld analysis.