Investigation of 2,4-dichlorophenoxyacetic acid adsorption onto MIEX resin: Optimization using response surface methodology

Orange peel magnetic activated carbon for removal of acid orange 7 dye from water

Magnetic activated carbon resources with a remarkably high specific surface area have been successfully synthesized using orange peels as the precursor and ZnCl2 as the activating agent. The impregnation ratio was set at 0.5, while the pyrolysis temperature spanned from 700 to 900 °C. This comprehensive study delved into the influence of activation temperatures on the resultant pore morphology and specific surface area. Optimal conditions were discerned, leading to a magnetic activated carbon material exhibiting an impressive specific surface area at 700 °C. The Brunauer-Emmett-Teller surface area reached 155.09 m2/g, accompanied by a total pore volume of 0.1768 cm3/g, and a mean pore diameter of 4.5604 nm. The material displayed noteworthy properties, with saturation magnetization (Ms) reaching 17.28 emu/g, remanence (Mr) at 0.29 emu/g, and coercivity (Hc) of 13.71 G. Additionally, the composite demonstrated super-paramagnetic behaviour at room temperature, facilitating its rapid collection within 5 s through an external magnetic field. Factors such as absorbent dose, initial concentration of the adsorbate, contact time, and pH were systematically examined. The adsorption behaviour for acid orange 7 (AO7) was found to adhere to the Temkin isotherm models (R2 = 0.997). The Langmuir isotherm model suggested a monolayer adsorption, and the calculated maximum monolayer capacity (Qm) was 357.14 mg/g, derived from the linear solvation of the Langmuir model using 0.75 g/L as an adsorbent dose and 150-500 mg/L as AO7 dye concentrations. The pseudo-second order model proved to be the best fit for the experimental data of AO7 dye adsorption, with a high coefficient of determination (R2) ranging from 0.999 to 1.000, outperforming other kinetic models.

Experimental design optimization of RP-HPLC method for simultaneous estimation of metsulfuron-methyl, chlorantraniliprole and chlorimuron-ethyl residues in stems of Oryza sativa

Background

The study aims to develop a chemometrics optimized D-optimal mixture design approach assisted RP- HPLC method for the determination of pesticide residues of metsulfuron-methyl, chlorantraniliprole, and chlorimuron-ethyl in the stems of Oryza sativa. Chromatographic separation was achieved on a C18 column using a mobile phase consisting of a pH 3.5 phosphate buffer and acetonitrile in the ratio 85:15.

Results

The optimized HPLC method gave a sharp resolution of metsulfuron-methyl, chlorantraniliprole and chlorimuron-ethyl at a retention time of 2.599 min, 3.805 min and 4.661 min receptively. Linearity was observed in the range 100‒500 µg/mL for metsulfuron-methyl (r2 = 0.999), 4‒20 µg/mL for chlorantraniliprole (r2 = 0.999) and 100‒500 µg/mL for chlorimuron-ethyl (r2 = 0.999). The developed method was validated as per ICH guidelines.

Conclusion

The proposed chemometrics optimized RP-HPLC method was found to be successful in the resolution of pesticide residues in the stems of O. sativa. The developed method can be applied to routine quantification of metsulfuron-methyl, chlorantraniliprole and chlorimuron-ethyl.

Evaluation of a hybrid process of magnetic ion-exchange resin treatment followed by ozonation in secondary effluent organic matter removal

The presence of effluent organic matter (EfOM) and organic micro-pollutants (OMPs) in secondary effluent is receiving increasing concern due to their potential impacts on the aquatic environment and human health. In this study, the removal characteristics of EfOM by magnetic ion-exchange resin (MIEX), ozonation, and the hybrid process of MIEX followed by ozonation (M + O) were compared by measuring the bulk organic indicators (BOIs), OMPs, bio-toxicity, and fluorescence. Furthermore, the desorption characteristics of MIEX were comprehensively studied. Ozonation could reduce the OMPs, total fluorescence (TF), genotoxicity, and oestrogenic activity more effectively than MIEX, with reductions of 80.3%, 97.8%, 98.9%, and 94.6%, respectively. The M + O process was capable of removing more EfOM than the individual MIEX or ozonation processes and could reduce the genotoxicity and oestrogenic activity to the detection limit. By implementing MIEX as a pre-treatment, the generation of ammonia-nitrogen and nitrate-nitrogen was effectively reduced in the subsequent ozonation process as MIEX adsorbed organic nitrogen and nitrite-nitrogen. The different regenerants influenced the OMP desorption performance of MIEX by changing the desorption mechanisms, and NaCl + NaOH was the best regenerant due to its high total OMP desorption efficiency. Parallel factor analysis coupled with self-organising maps further explained the differences in fluorescence desorption due to the addition of NaOH to the regenerated solution. Pearson correlation analysis indicated the potential of using spectroscopic indicators, such as ultraviolet absorbance and TF, to assess the evolution of OMPs and bio-toxicity during the M + O and MIEX desorption processes.

In-situ fabrication of a spherical-shaped Zn-Al hydrotalcite with BiOCl and study on its enhanced photocatalytic mechanism for perfluorooctanoic acid removal performed with a response surface methodology

Perfluorooctanoic acid (PFOA), a widely used compound, is harmful to the environment and human health. In this study, a facile one pot solvothermal method of integrating BiOCl with Zn-Al hydrotalcite to form spherical-shaped BiOCl/Zn-Al hydrotalcite (B-BHZA) sample is reported. The characteristics and main factors affecting photocatalytic PFOA and photocatalytic mechanism of BiOCl/Zn-Al hydrotalcite (B-BHZA) are systematically investigated. It is found that spherical-shaped B-BHZA possesses abundant defects and a larger surface area of 64.4 m² g^-1. The factors affecting photocatalytic removal PFOA (e.g., time, pH, initial concentration and dosage) are investigated by modeling the 3D surface response. The removal rate of PFOA is over 90 % in 6 h under UV light at an optimal pH of 2, an initial concentration of 500 μg/L and a dose of dosage 0.5 g/L. The main mechanism occurs by photo-generated h⁺ oxidation and synergistic effects from the photocatalysis process. Though investigating the intermediates of PFOA degradation and F^-, a possibility was proposed that h⁺ initiated the rapidly decarboxylation of PFOA. The unstable perfluoroheptyl group is formatted and further conversed to short chain perfluorocarboxylic acid. This study provides a new insight for the preparation of highly efficient photocatalysts to the treatment of halogenated compounds in UV system.

Process Parameters Optimization of Gallic Acid Removal from Water by MIEX Resin Based on Response Surface Methodology

In this work, the response surface methodology was used to optimize the process parameters of gallic acid adsorption on magnetic ion exchange (MIEX) resin. Based on Box-Behnken Design, a quadratic polynomial model equation including solution pH, gallic acid concentration, MIEX resin dosage and adsorption time was established. The reliability of the established regression equation was tested by variance analysis. Based on the regression equation, the technical parameters for gallic acid adsorption on MIEX resin were optimized and the effects of interaction between variables on the removal of gallic acid were analyzed. The results showed that the established regression equation was reliable and could effectively predict the removal of gallic acid. The optimal technical parameters were determined to be a pH of 9.17, a gallic acid concentration of 8.07 mg/L, a resin dosage of 0.98 mL/L and an adsorption time of 46.43 min. The removal efficiency of gallic acid was 97.93% under the optimal parameters. The interaction between pH and adsorption time had the most significant effect on the removal of gallic acid. The results of this study demonstrated that MIEX resin can remove gallic acid efficiently and relatively quickly under the condition of optimal technical parameters.

Enhancement in Iron Absorption on Intake of Chemometrically Optimized Ratio of Probiotic Strain Lactobacillus plantarum 299v with Iron Supplement Pearl Millet

This research article aims to establish the intake ratio of probiotic Lactobacillus plantarum 299v with iron supplement pearl millet by central composite design of response surface methodology so as to enhance iron absorption. In anemic rat models, the food intake pattern, body weight, hemoglobin content, and hematocrit values were found to be significantly increased on treatment with pearl millet:probiotic; however, incorporation of probiotics at lower dose (0.5 g) was significantly (p < 0.05) effective in enhancing iron absorption, and further increment in probiotic doses (1.0 g) did not produce significant increase in hemoglobin and hematocrit values as evidenced by the experimental findings.

Removal of 2,4-D, glyphosate, trifluralin, and butachlor herbicides from water by polysulfone membranes mixed by graphene oxide/TiO2 nanocomposite: study of filtration and batch adsorption

PURPOSE

Degradation or decomposition of the chemical herbicides by natural reagents after using can lead to produce various types of harmful intermediates. Ultrafiltration by the mixed matrix membranes blended with the graphene oxide/TiO₂ can remove the residual herbicides from aqueous solution.

METHODS

Graphene oxide/TiO₂x% (x = 10, 30, 50%) was prepared by solvothermal method and blended by polysulfone to prepare GO/TiO₂/PSf membranes for dynamic rejection of aqueous solutions of glyphosate, 2,4-D, butachlor, and trifluralin in a dead-end flow system. The blended membranes were also applied for the adsorption of herbicides in batch experiments.

RESULTS

Addition of GO/TiO₂ nanocomposite increased water flux from 7.3 for pure membrane to 211-326 kg/m² h for mixed matrix samples in order to increase of the membrane porosity and surface hydrophilicity. The herbicides rejections were found in the range of 50-70% related to GO/TiO₂ content. It was found that the membrane blended with 0.5 wt.% of GO/TiO₂(10%) demonstrated the most efficiency.

CONCLUSIONS

Details of dynamic filtration showed that the blended membrane acted based on the size exclusion mechanism. Adsorption experiments indicated that the strong attractions between H-bond donor sites of the herbicide and GO/TiO₂ nanoparticles in membranes played a key role in the increase of adsorption of herbicides on the membrane.

Magnetic ion exchange resin for effective removal of perfluorooctanoate from water: study of a response surface methodology and adsorption performances

This research exhibited the use of magnetic ion exchange (MIEX) resin as an effective adsorbent for the removal of perfluorooctanoate (PFOA) in aqueous solution. The adsorption performance of PFOA was investigated by a batch experiment. All kinds of factors affecting the adsorption of PFOA, including adsorbent dosage, initial concentration, adsorption time, temperature, stirring intensity, coexistent anions, initial solution pH, natural organic matter, ion strength, and bed volume were studied. Moreover, the response surface methodology was put into use to know the key parameters affecting PFOA removal efficiency. The sorption equilibrium and kinetic data could conform well to the Langmuir and pseudo-second-order model, respectively. Thermodynamic parameters were obtained, and it was observed that the adsorption of PFOA onto MIEX resin was an endothermic and spontaneous process at the temperatures under investigation. It was summarized that both chemical absorption and physical adsorption were involved in the PFOA sorption onto the MIEX resin. Moreover, the MIEX resin could be effectively regenerated using a saturated sodium chloride solution. A series of batch experiments and characterizations demonstrated that the MIEX resin possessed a strong adsorption ability with the removal efficiency exceeding 90%, allowing a possible practical application in future water treatment.

OPAC (orange peel activated carbon) derived from waste orange peel for the adsorption of chlorophenoxyacetic acid herbicides from water: Adsorption isotherm, kinetic modelling and thermodynamic studies

This study presents the orange peel activated carbon (OPAC), derived from biowaste precursor (orange peel) by single step pyrolysis method and its application for the adsorption of chlorophenoxyacetic acid herbicides from the water. The OPAC exhibited the surface area of 592.471 m² g^-1, pore volume and pore diameter of 0.242 cc g^-1 and 1.301 nm respectively. The adsorption kinetics and thermodynamic equilibrium modelling for all chlorophenoxyacetic acid herbicides were investigated. The various parametric effects such as pH and temperature were evaluated. A pseudo-second-order kinetic model was well fitted for all the herbicides. The Langmuir isotherm was obeyed for all the herbicides and the maximum Langmuir capacity of 574.71 mg g^-1 was achieved. The thermodynamic studies revealed that the adsorption increases with increase in temperature. The results shows that the orange peel derived carbon (OPAC) as effective and efficient adsorbent material for the removal of chlorophenoxyacid herbicides from the water.

Novel magnetic carboxyl modified hypercrosslinked resins for effective removal of typical PPCPs

A series of novel magnetic carboxyl modified hypercrosslinked resins were successfully prepared via a sequence of suspension polymerization, hydrolysis and post-crosslinking reactions. The serial resins possessed both high cation exchange capacity and high specific surface area with MA-10 having the supreme specific surface area of 1238.65 m²/g and MA-70 having the largest exchange capacity of 6.45 mmol/g. The serial resins exhibited excellent adsorption capacity of typical PPCPs including chloramphenicol, atenolol, ibuprofen and tetracycline, which were neutral, cationic, anionic and zwitterionic respectively in natural water. The adsorption of chloramphenicol and ibuprofen was dominated by the hydrophobic and π-π Electron-Donor-Acceptor (EDA) interactions, while as to atenolol, the electrostatic interaction dominated the adsorption process. Especially, MA-50 was found to have the largest adsorption amount and the longest equilibrium time of zwitterionic tetracycline compared with other resins, the mechanism of which needed further investigation. Breakthrough tests showed that the serial resins had significant advantages over granular activated carbon F400D in contaminants removal for all of the four target pharmaceuticals. Batch experiments proved that the serial resins possessed strong anti-pollution ability and excellent regeneration property, which made it possible for the practical application in future water treatment.

Control of disinfection by-product derived from humic acid using MIEX process: optimization through response surface methodology

Response surface methodology (RSM) was used to optimize humic acid (HA) removal by MIEX resin for controlling the disinfection by-product (DBP) formation.